Johnson Controls LP-NRM001-000C Installation guide

Brand: Johnson Controls

Model: LP-NRM001-000C

Type: Installation guide

This manual is also suitable for

Network Room Modules

Installation Guide

Part No. 24-85638-1214, Rev. E

Issue Date June 14, 2010

Figure 1: Dimensions, mm (in.)

80 (3.15)

120

(4.72)

25 (0.98)

(6)

Display

in Celsius and

Fahrenheit units

80 (3.15)

(1.38)

(1)

LCD Display

with back-light

(2)

Dial for Temperature

Setpoint Adjustment

(3)

°C / °F Button

(4)

Fan Button for fan speed adjustment

(5)

Service tool socket

Figure 2: Removing the Cover from the Base

III

Figure 3: Wall Mounting Base Dimensions, mm (in.)

31 (1.22)

60 (2.36)

2 x Ø 4.2 (0.16)

66 (2.60)66 (2.60)

60 (2.36)

4,3 (0.17)

4,3 (0.17) 4,3 (0.17)

29 (1.14)

(1.30)

(1.50)

5.7 (0.22)

34 (1.34)

67 (2.64)

Figure 4: Dual-Switch DIP Switch Block

Figure 5: Terminal Block Connection

Figure 6: Service Port (4-pin) for LP-NRM0xx-000C Series

Figure 7: Port (6-pin Modular Jack) for LP-NRM5xx-000C and

LP-NRM6xx-000C Series

1Network Room Modules Installation Guide

Network Room Modules

Installation Guide

READ THIS INSTRUCTION SHEET AND THE SAFETY WARNINGS

CAREFULLY BEFORE INSTALLING, AND SAVE IT FOR FUTURE USE

General Features

• Network Room Modules (NRMs) are designed for use with

Johnson Controls® Facility Explorer FX06, FX07, FX14, and FXVMA

Field Controllers.

• The Liquid Crystal Display (LCD), along with a dial and push button(s) on

the front of the NRM, allow the occupant to view and adjust the setpoint

temperature in the controller, and to manually override the speed of the

fan in the controlled equipment.

• The NRM connects to the Local Link Display Bus of the FX field

controller. Configure the NRM with the FX Builder programming tool,

which is part of the FX Tools Pro Software package.

• The LP-NRM0xx-000C Series NRM requires a 15 to 24 VAC/VDC power

supply from the FX Controller or from an external power source, and has

a 4-pin service port (Figure 6).

• The LP-NRM5xx-000C and LP-NRM6xx-000C Series NRMs require a

15 VDC power supply from the FX Controller or from an external power

source, and have a 6-pin Modular Jack service port (Figure 6).

North American Emissions Compliance

United States

This equipment has been tested and found to comply with the limits for a

Class A digital device pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

when this equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may

cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference, in

which case the user will be required to correct the interference at his/her

own expense.

Part No. 24-85638-1214, Rev. E

Issue Date June 14, 2010

2 Network Room Modules Installation Guide

Canada

This Class (A) digital apparatus meets all the requirements of the Canadian

Interference-Causing Equipment Regulations.

Cet appareil numérique de la Classe (A) respecte toutes les exigences du

Règlement sur le matériel brouilleur du Canada.

Tools

• Flat-head screwdrivers, 3 mm and 5 mm (1/8 to 5/32 in.)

• Drill, bits, and appropriate 4 mm (3/16 in.) screws and plugs

• Pointed tool (available from Johnson Controls, Ordering Code TM-9100-8900

in Europe, or T-4000-119 in North America)

Figure 1: Dimensions, mm (in.)

(1) LCD Display with backlight

(2) Dial for temperature set point adjustment

(3) °C/°F Button

(feature available in specific models, see Ordering Codes)

(4) Fan button for fan speed adjustment

(feature available in specific models, see Ordering Codes)

(5) Service port

(6) Display in Celsius and Fahrenheit units

Mounting

The NRM mounts directly on a wall surface in the room you want to control.

Choose a location for the NRM while considering the following information:

• Place the room module where the occupant can easily read the LCD and

use the controls.

• Place the module where the ambient temperature is representative of the

general room conditions if you want to use the built-in temperature

sensor to measure space temperature. For example, there should be a

sufficient amount of air circulation.

• Avoid cold or warm air drafts, radiant heat, and direct sunlight.

• Place some insulating material in the wiring access hole or conduit to

prevent the introduction of air from outside the room.

3Network Room Modules Installation Guide

Figure 2: Removing the Cover from the Base

1. Remove the retaining screw (if inserted) from the top of the module

enclosure.

2. Remove the module cover from the base by inserting a pointed tool into

the narrow slot at the center top of the cover. While pressing down

gently, pry the base away from the cover. As the two parts separate,

remove the tool and continue to pull the cover away from the base until

the cover is free.

Figure 3: Wall Mounting Base Dimensions, mm (in.)

1. Hold the module base on the wall to cover the electrical outlet and mark

the position of at least two holes. Drill the holes and insert the plastic

plugs (wall anchors) into the holes.

2. Mount the module base on the wall and secure with at least two screws.

For other mounting options, see Ordering Codes and refer to the

corresponding installation sheets.

Addressing

Figure 4: Dual-Switch DIP Switch Block

NRM models which are not addressable have a fixed physical address of

191. For those models which are addressable, the NRM's address must be

set using its dual-switch DIP switch block, located on the printed wiring

board. See Table 1 for details on addressing the NRM.

Note: You must cycle power to the NRM (disconnect/reconnect the NRM

or cycle power to the field controller) for the address change to take

effect.

Table 1: NRM Addressing

DIP Switch

Address

Switch 2 Switch 1

191 OFF OFF

192 OFF ON

193 ON OFF

194 ON ON

4 Network Room Modules Installation Guide

Wiring

CAUTION: Risk of Electric Shock.

Disconnect power supply before making electrical

connections to avoid electric shock.

IMPORTANT: The Complementary Metal Oxide Semiconductor

(CMOS) circuits in the controller are sensitive to static electricity.

Take suitable precautions.

IMPORTANT: The LP-NRM0xx-000C Series NRM accepts VAC or

VDC power. The LP-NRM5xx-000C and LP-NRM6xx-000C Series

accept VDC power only.

IMPORTANT: Use this NRM Room Command Module only as an

operating control. Where failure or malfunction of the NRM could

lead to personal injury or property damage to the controlled

equipment or other property, additional precautions must be

designed into the control system. Incorporate and maintain other

devices, such as supervisory or alarm systems or safety or limit

controls, intended to warn of or protect against failure or

malfunction of the NRM.

IMPORTANT: The installation of electrical wiring must conform to

local codes and should be carried out by authorized personnel only.

Users should ensure that all Johnson Controls products are used

safely and without risk to health or property.

5Network Room Modules Installation Guide

Figure 5: Terminal Block Connection

• Terminations are made on the terminal block in the base of the module,

which is accessible after removing the cover from the base.

• The screw terminals accept up to 1.5 mm

(16 AWG) wires.

• Keep low-voltage wiring separated from power line voltage wiring.

• Do not run wiring close to transformers or high frequency generating

equipment.

• Complete and verify all wiring connections before applying power to the

module.

• Use screw terminals RT+, RT-, and COM to connect to the FX controller

display (local ink) bus terminals (LL+, LL-, and COM, respectively).

Note: RT+ and RT- are polarity sensitive and are not interchangeable.

• If shielded cable is used, connect the shield to a clean earth ground at

one end only.

• Connect the power supply voltage to the terminals as marked:

- 15-24 VAC/VDC and COM (common) for the LP-NRM0xx-000C

Series NRM

- 15 VDC and COM (common) for the LP-NRM5xx-000C and

LP-NRM6xx-000C Series NRMs

Service Port

The service port is located on the lower edge of the module. There are two

different types of service ports, depending on the NRM Series you are

using:

4-Pin Service Port

See Figure 6 for service port wiring for LP-NRM0xx-000C Series NRM.

Use the 4-pin service port to download applications into the connected FX

Controller using the Programming Key (pass-through feature). The NRM

supplies power to the Programming Key.

6-Pin Modular Jack Service Port

See Figure 7 for service port wiring for LP-NRM5xx-000C and

LP-NRM6xx-000C Series NRMs.

Use the 6-pin Modular Jack service port to connect a Medium User

Interface (MUI) for monitoring and adjusting parameters in the control

application of the connected FX controller. The NRM supplies power to the

MUI from the FX controller through the 6-pin Modular Jack service port.

6 Network Room Modules Installation Guide

Ordering Codes

Table 2: Network Room Modules (Available in Europe)

Table 3: Network Room Modules (Available in North America)

Product Code Features/Options

Size (mm)

Service Port Type

LCD Display

Temperature

Adjust Dial

Fan Speed

Selector Button

°F/°C

Addressable

LP-NRM001-000C 80 x 80 Program

Key

No No No No No

LP-NRM002-000C Yes Yes No No No

LP-NRM003-000C Yes Yes Yes No No

LP-NRM511-000C MUINoNoNoNoYes

LP-NRM502-000C Yes Yes No No No

LP-NRM503-000C Yes Yes Yes No No

Product Code Features/Options

Size, mm (inch)

Service Port Type

LCD Display

Temperature

Adjust Dial

Fan Speed

Selector Button

°F/°C

Addressable

LP-NRM511-000C 80 x 80

(3.15 x

3.15 in.)

MUINoNoNoNoYes

LP-NRM552-000C Yes Yes No Yes No

LP-NRM553-000C Yes Yes Yes Yes No

LP-NRM611-000C 120 x 80

(4.72 x

3.15 in.)

MUINoNoNoNoYes

LP-NRM652-000C Yes Yes No Yes No

LP-NRM653-000C Yes Yes Yes Yes No

7Network Room Modules Installation Guide

Table 4: NRM Mounting Kits and Accessories

Table 5: Recommended FX Controller and MUI/NRM

Configuration Limits

1. One addressable NRM is required.

Ordering Codes Description

TM-1100-8931 Plastic Base for Surface Mounting - White

TM-9100-8941-W Recessed Wall Box Mounting Kit - White

TM-9100-8951-W Panel Mounting Kit - White

NS-WALLPLATE-0 Wall plate kit used to mount an 80 x 80 mm (3.15 x 3.15 in.)

NRM onto a 2 x 4 in. wall box.

TM-9100-8900 Special Tool (to open module) - Europe

T-4000-119 Special Tool (to open module) - North America

LP-KIT100-000C Programming Key

FX Controller Type MUI/NRM Configuration Limits

FX06 One MUI and one NRM

FX06 Rev A One MUI and one NRM

FX07 One MUI and one NRM

FX07 Rev A One MUI and one NRM

FX14 One MUI and two NRMs

FX14 Rev A One MUI and two NRMs

FX14 Rev B One MUI and two NRMs

FX15 Universal NRM is not supported

FX15 NRM is not supported

FX15 Rev A NRM is not supported

FX16 NRM is not supported

FX16 Rev A NRM is not supported

FX16 Rev B NRM is not supported

FXVMA One MUI and one NRM

FXVMA Rev A One MUI and one NRM

8 Network Room Modules Installation Guide

Technical Specifications

NRM Technical Specifications (Part 1 of 2)

Product Network Room Module

Power Requirements

LP-NRM0xx-000C

Series

14.3 to 27.6 VDC at 500 mW maximum or

24 VAC ±15%, 50/60 Hz,

at 1 VA maximum

Class 2 or Safety Extra-Low Voltage (SELV)

Power Requirements

LP-NRM5xx-000C and

LP-NRM6xx-000C

Series

9.8 to 16.5 VDC (15 VDC nominal)

at 35 mA maximum

Class 2 or SELV

Ambient Operating

Conditions

0 to 50°C (32 to 122°F)

10 to 90% RH noncondensing

(and max. 30°C [86°F] dew point)

Ambient Storage

Conditions

-20 to 70°C (0 to 160°F)

5 to 95% RH noncondensing

(and max. 30°C [86°F] dew point)

Terminations Terminal block with screw terminals in base for

1.5 mm

/ 16 AWG (max.) wires.

Recommended tightening torque 0.5 Nm.

Temperature Sensor RTD Platinum element, PTC, 1k ohm at 0°C (32°F),

Pt1000 Class A, DIN EN 60751

Suitable for residential and commercial office

environments only.

Display and Controls LCD display with three digits and seven symbols.

Dial and push button(s).

Communications

Interface

N2 Open Protocol communication

Service bus RS485 at 9600

baud

Service Port Model LP-NRM0xx:

4-pin service port for FX Programming Key with

9 VDC power

Models LP-NRM5xx and LP-NRM6xx:

6-pin Modular Jack service port for MUI with

15 VDC power

Mounting Direct surface mount.

Plastic base for surface mount with wiring conduits.

Recessed wall box and panel mounting kits

available on request (see

Ordering Codes).

Dimensions

(H x W x D)

80 x 80 x 35 mm (3.15 x 3.15 x 1.4 in.)

120 x 80 x 35 mm (4.72 x 3.15 x 1.4 in.)

9Network Room Modules Installation Guide

Housing Material ABS + polycarbonate, self-extinguishing UL94-HB

Housing Protection IP30 (EN60529)

Shipping Weight 0.2 kg (7 oz), 80 x 80 mm (3.15 x 3.15 in.) housing

or 0.25 kg (9 oz), 120 x 80 mm (4.72 x 3.15 in.)

housing

Compatible FX

Controllers and

Firmware Versions

FX06, V 2.32 and higher

FX07, V 3.01 and higher

FX14, V 2.32 and higher

FXVMA, all versions

Compliance Europe

CE Mark – Johnson Controls, Inc., declares that the

Network Room Modules (NRMs) are in compliance

with the essential requirements and other relevant

provisions of the EMC Directive 2004/108/EC.

Canada

UL Listed (PAZX7), C22.2 No. 205,

Signal Equipment Industry Canada, ICES-003

United States

UL Listed (PAZX), UL 916, Energy Management

Equipment

FCC compliant to CFR 47, Part 15, Subpart B,

Class A

Agency Listings UL916 and CUL Listed

This document is subject to change without notice.

NRM Technical Specifications (Part 2 of 2)

10 Network Room Modules Installation Guide

Building Efficiency

507 E. Michigan Street, Milwaukee, WI 53202

Johnson Controls® is a registered trademark of Johnson Controls, Inc.

Johnson Controls LP-NRM001-000C Installation guide

Brand: Johnson Controls

Model: LP-NRM001-000C

Type: Installation guide

This manual is also suitable for

Download PDF

report

Johnson Controls LP-NRM001-000C Installation guide

This manual is also suitable for

Johnson Controls LP-NRM001-000C Installation guide

Related papers

Other documents