MATSONIC MS7012D User manual

Important Information

Copyright

This publication, including all photographs, illustrations and software, is

Neither this manual, nor any of the material contained herein, may be

reproduced without the express written consent of the manufacturer.

Disclaimer

The information in this document is subject to change without notice. The

manufacturer makes no representations or warranties with respect to the

contents hereof and specifically disclaims any implied warranties of

merchantability or fitness for any particular purpose. Further, the

manufacturer reserves the right to revise this publication and to make

changes from time to time in the content hereof without obligation of the

manufacturer to notify any person of such revision or changes.

Trademark Recognition

Microsoft, MS-DOS and Windows are registered trademarks of Microsoft

Corp.

MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered

trademarks of Intel Corporation.

VGA, OS/2, PS/2 are registered trademarks of International Business

Machines.

AMD, K5, K6 are registered trademarks of Advanced Micro Devices Inc.

Cyrix, M1 are registered trademarks of Cyrix Corporation.

Other product names used in this manual are the properties of their

respective owners and are acknowledged.

Version 2.0

Safety Compliance

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to

radio communications. However there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following

measures:

q Reorient or relocate the receiving antenna.

q Increase the separation between the equipment and the receiver.

q Connect the equipment onto an outlet on a circuit different from that

to which the receiver is connected.

q Consult the dealer or an experienced radio/TV technician for help.

Shielded interconnect cables and shielded AC power cable must be

employed with this equipment to insure compliance with the pertinent RF

emission limits governing this device. Changes or modifications not

expressly approved by the system’s manufacturer could void the user’s

authority to operate the equipment.

Declaration of Conformity

This device complies with part 15 of the FCC rules. Operation is subject

to the following conditions:

q This device may not cause harmful interference, and

q This device must accept any interference received, including

interference that may cause undesired operation.

Canadian Department of Communications

This class B digital apparatus meets all requirements of the Canadian

Interference-causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du

Réglement sur le matériel brouilieur du Canada.

Contents

Chapter 1: Introduction...........................................1

Welcome..................................................................1

About the Manual......................................................2

Checklist..................................................................3

Standard Items -------------------------------------------------------3

Recommendations....................................................3

Features...................................................................4

Chapter 2: Installation.............................................8

Quick Installation Table.............................................8

Quick Jumper Setting Reference................................9

Before You Begin......................................................11

Static Electricity------------------------------------------------------11

Choosing a Case-----------------------------------------------------11

How to Set Jumpers ------------------------------------------------12

Preparing the Mainboard...........................................13

Mainboard Guide-----------------------------------------------------13

I/O Ports Side View-------------------------------------------------15

Check the Jumper Settings --------------------------------------16

Install the Mainboard in the Case...............................19

Connecting Power, Chassis Fans, Panel,

Auxiliary USB Ports, and Case Open Detect Circuit---21

Install Other Hardware...............................................23

Install the Processor------------------------------------------------23

Installing a Slot1 Processor--------------------------------------25

Installing a Socket-370 Processor----------------------------27

Install the Memory Modules -------------------------------------29

Install a Hard Disk Drive and CD-ROM---------------------30

Installing a Floppy Diskette Drive------------------------------33

Using the Expansion Slots---------------------------------------34

Add-in Card Options------------------------------------------------36

Install Options and Extension Brackets---------------------37

Make the External Connections .................................42

External Connector Color Coding-----------------------------43

Chapter 3: Setup.....................................................44

About the Setup Utility...............................................44

Starting the Setup Utility------------------------------------------44

How to Flash a New BIOS ---------------------------------------46

Standard CMOS Features Option...............................47

Advanced BIOS Features Setup Option......................49

Advanced Chipset Features Option............................51

Integrated Peripherals Option ....................................53

Power Management Setup Option..............................56

PNP/PCI Configuration Option...................................59

PCI Health Status Option...........................................60

Frequency / Voltage Control Option............................61

Load Fail-Safe Defaults Option ..................................62

Load Optimized Defaults Option.................................62

Set Supervisor and User Passwords ..........................62

Save And Exit Setup Option.......................................63

Exit Without Saving Option........................................63

Chapter 4: Software................................................64

About the Software....................................................64

Folders for this Mainboard.........................................64

Running the Support CD-ROM...................................66

Utility Folder Installation Notes...................................66

CMI8X38 Folder Installation Notes .............................67

Audio Software--------------------------------------------------------67

Modem Driver and Software-------------------------------------68

Intel Folder Installation Notes.....................................68

Mainboard (MS7012D) Installation Notes....................69

Appendix 1: Quick Jumper Setting Reference ........70

1

C

h

a

p

t

e

r

1

:

I

n

t

r

o

d

u

c

t

i

o

n

Welcome

Congratulations on purchasing the MS7012D mainboard. The mainboard

includes a Slot1 processor slot and a PPGA (Plastic Pin Grid Array)

Celeron Socket-370 processor socket. This feature means that you

can install the mainboard with a Pentium-iii or Pentium-II cartridge,

the SEPP (Single Edge Processor Package) Celeron cartridge, or

one of the new generation PPGA Celerons.

The MS7012D is a full-sized ATX mainboard that uses 4-layer printed

circuit board and measures 305mm x 243mm. The mainboard features

the new low-cost Intel 810 chipset which includes an accelerated

graphics adapter with digital video output for use by televisions of flat-

panel displays. The MS7012D has a slot1 and a socket-370 so that it

can be installed with either a slot1 processor (SEPP Celeron or Pentium-

II) or a socket-370 processor (PPGA Celeron). The mainboard includes

integrated graphics system, integrated audio system, and integrated

fax/modem. A powerful internet-ready workstation can be developed with

just the addition of processor and memory. Therefore the MS7012D is

the ideal platform for the creation of a powerful value PC.

2

This chapter contains the following information:

q About the Manual explains how the information in this manual is

organized

q Checklist comprises a list of the standard and optional components

that are shipped with this mainboard

q Recommendations lists some Do’s and Don’ts from the

manufacturer to help ensure reliability and performance from this

product

q Features highlights the functions and components that make this

one of the best value mainboards on the market

About the Manual

The manual consists of the following chapters:

Introduction

Use the Introduction Chapter to learn about the features of the

mainboard, and the checklist of items that are shipped with the package.

Installation

Use the Installation Chapter to learn how to install the mainboard and

get your system up and running.

Setup

Use the Setup Chapter to configure the mainboard for optimum

performance.

Software

Use the Software Chapter to learn how to use the software drivers and

support programs that are provided with this mainboard.

3

Checklist

Compare the contents of your mainboard package with the standard

checklist below. If any item is missing or appears damaged, please

contact the vendor of your mainboard package.

Standard Items

ü

1 x MS7012D Mainboard

ü

1 x Cable/Bracket Pack

Diskette drive ribbon cable

IDE drive ribbon cable

ü

Serial ports extension bracket

ü

This User’s Manual

ü

Software Support CD-ROM Disc

Optional Items

ü

1 x V.90 Fax/modem Card

ü

1 x TV-out extension bracket

Recommendations

This mainboard automatically determines the CPU clock frequency and

system bus frequency for the kind of processor that you install. You may

be able to change these automatic settings by making changes to

jumpers on the mainboard, or changing the settings in the system setup

utility. We strongly recommend that you do not overclock the mainboard

to run processors or other components faster than their rated speed.

Overclocking components can adversely affect the reliability of the

system and introduce errors into your system. Overclocking can

permanently damage the mainboard by generating excess heat in

components that are run beyond the rated limits.

Components on this mainboard can be damaged by discharges of static

electricity. Handle the board carefully holding it by the edges. Don’t flex

or stress the circuit board. Keep the board in its static-proof packing until

you are ready to install it. Follow the static guidelines given at the

beginning of Chapter 2.

4

Features

The key features of this mainboard are the wide range of processors that

can be installed, and the high level of integration which includes built-in

audio, video, and communications.

Value-class Processors

Functioning as a platform for a value PC, the MS7012D is ideally suited

for the PPGA (Plastic Pin Grid Array) Celeron processor. The PPGA

Celeron has 32k of internal cache memory, 128K of external cache

memory, and operates over a 66MHz system bus. The PPGA Celeron

ships with clock speeds running from 300 MHz through to 500 MHz. The

PPGA Celeron is the premiere choice for an entry-level PC. For slightly

better performance, the MS7012D can be installed with a slot-1

processor. The SEPP (Single Edge Processor Package) Celeron is the

least expensive Dlot-1 processor. It has 32K of internal cache memory,

128K of external cache memory (except for older versions), and

operates over a 66 MHz system bus. SEPP Celerons ship with clock

speed ranging from 266 MHz through 500 MHz.

For higher-performance business class computing, the slot-1 can be

installed with a Pentium-III or Pentium-II processor cartridge. The

Pentium cartridges have 32K of internal cache memory and 512K of

external cache memory. They operate over a 100 MHz system bus

(except for older versions). The Pentium-II ships with clock speeds

running from 233 MHz through to 450 MHz and the Pentium-III ships

with clock speeds of 450, 500, and 550 MHz

Intel’s 810 Chipset

This board features the 810 chipset from Intel. The 810 chipset is

designed to reduce the cost and improve the multimedia capability of

value PCs. The chipset features an integrated AGP (Accelerated

Graphics Port) graphics controller which is optimized to produce smooth

rendition of 2D and 3D video. Digital video output is supported so that

the system can display on a TV or a flat-panel display with digital video

input. The graphics controller improves performance and reduces cost

by dynamically allocating a segment of active memory as video memory.

The 810 I/O chip (82801 I/O Controller Hub) makes a direct connection

between the graphics system and the IDE controller and the PCI bus. It

uses Accelerated Hub Architecture to effectively double the bandwidth

between these components enabling more life like audio and video. It

includes an integrated Audio-Codec controller (AC97) that lets the

5

processor more effectively decode sound generated by the integrated

audio system or the integrated fax/modem. Finally, the P82802 Firmware

Hub allows the system and video BIOS to be stored (eliminating the

need for non-volatile CMOS memory) for faster execution, and provides

a random number generator to enable strong encryption routines.

Inexpensive Memory

The board has two DIMM sockets for the installation of 168-pin, 3.3V

non-buffered DIMM memory modules. The DIMM memory modules must

be installed with SDRAM memory chips. The board supports a memory

bus of 66 MHz or 100 MHz, so you can choose between inexpensive 66

MHz memory modules or high-performance PC-100 memory modules.

Each installed memory module can be populated with 8 MB up to 256

MB of memory, so a maximum total of 512 MB memory can be installed.

The integrated video system uses a shared memory architecture so that

you must reserve some of the installed memory as video memory using

the system BIOS. You must install at least one memory module.

Highly Integrated Design

As well as the Intel 810 chipset, the MS7012D features other highly

integrated silicon chips. The ITE LPC I/O controller handles the

mainboard’s I/O functions. The CMI 8738/PCI C3DX is a two-chip

solution that provides an integrated audio and fax/modem system. The

Chrontel CH7007A is a single chip dedicated to converting digital PC

output to a TV format.

Built-in AGP 3D-Graphics

The Intel 810 chipset includes an integrated AGP controller that is

optimized for smooth 2D and 3D video. The graphics system shares

active memory and does not require dedicated video memory. Video is

delivered through a regular 15-pin connector, or as a low cost alternative

to a monitor, the system can display on a regular TV set by using an

optional TV-out extension bracket with an RCA video jack.

Built-in PCI 3D Sound

The PCI Audio CMI 8738 is a single chip solution for PCI-bus 3D audio.

The chip provides Sound Blaster 16-bit-compatible audio, plus support

for Microsoft’s DirectSound 3D specification and Aureal A3D interface.

The sound ports include jacks for speakers, microphone and stereo in,

and a game/MIDI port. The audio system supports full duplex operation

and drivers are available for WIN 95/98 and WIN NT 4.0. The audio

system can output sound to 4 loudspeakers and also supports SPDIF

24-bit digital sound input and output.

6

Built-in V.90 Fax/modem

The PCI C3DX chip is a single chip solution for value PC

communications. The chip supports 56 Kbps transmission using rhe V.90

protocol. The chip is integrated with the built-in audio system to support

voice as well as data transmissions.

Up-to-date Expansion Options

This is a full-sized ATX board with a full set of current technology

expansion slots. The mainboard no longer supports the legacy ISA

(Industry Standard Architecture) 8/16-bit slots. Instead, the board

provides five 32-bit PCI (Peripheral Components Interconnect) slots, with

each slot supporting Ultra DMA 66/33 and bus mastering. In addition, the

board has an AMR slot. The AMR slot lets you install an AMR (Audio

Modem Riser) card. Because the regulations regarding the use of

modems is different from country to country, mainboard manufacturers

can simply install a standard AMR slot which can be used by third-party

Audio Modem Riser cards that have been certified for use in the local

territory.

Integrated I/O

Using the ITE LPC I/O chip and the Intel 810 chipset, the board has a

comprehensive set of integrated I/O ports. The I/O port array features

PS/2 keyboard and mouse ports, a parallel port, two USB ports, one

serial port, a monitor port, a game/MIDI port, and three audio jacks. The

mainboard has connectors for the installation of a second serial port,

TV-out ports (supplied on optional extension brackets), an infrared port

(for IrDA or ASKIR), a fax/modem card, and two additional USB ports.

The mainboard includes connections for floppy diskette drives and two

PCI IDE channels.

Keyboard Power On Feature

Using the system BIOS setup program, you can configure the system to

turn on using a keyboard typed password. A green keyboard is not

required.

Programmable Firmware

The mainboard includes Award BIOS which allows BIOS setting of CPU

parameters. The fully programmable firmware enhances the system

features and allows users to set power management, CPU and memory

timing, LAN and modem wake-up alarms, and so on. The firmware can

also be used to set parameters for different Celeron processor clock

speeds so that you don’t need to change mainboard jumpers and

switches.

7

Suspend to RAM Feature

This mainboard features the suspend to RAM function. In a suspend to

RAM, the system is totally powered down with the exception of the small

current required to refresh the system memory. To resume from a

suspend to RAM, press the power button (or use the hot keys or

password if you have enabled a hot-key or password power on). The

system will resume in just a few seconds, and it will appear in exactly the

same state as it was before it was suspended to RAM.

8

C

h

a

p

t

e

r

2

:

I

n

s

t

a

l

a

t

i

o

n

Quick Installation Table

This chapter explains how to successfully install the mainboard into a

computer case and build a working system. The installation procedure is

as follows:

Quick Jumper

Setting Reference

Provides a quick reference for the jumper

settings on this mainboard.

Before you Begin Provides advice on choosing a case,

avoiding static electricity damage, and setting

jumpers.

Preparing the

Mainboard

Provides a guide to the mainboard and I/O

port locations, full details on the jumper

settings, and advice on installing the

mainboard in the system case.

Install Other

Hardware

Provides guidance on installing essential

hardware: processor, memory, hard disk

drive, CD-ROM, floppy disk drive, and

expansion cards.

Make the External

Connections

Provides advice on using the external I/O

ports to install peripheral devices such as a

keyboard, a monitor, a mouse, a printer,

loudspeakers, and so on.

9

Quick Jumper Setting Reference

If you are familiar with most of the material in this chapter, you can begin

preparing the mainboard for installation by using this quick reference to

begin the setting the jumpers. A detailed description of the jumper setting

appears later in this chapter.

JP1: Clear CMOS memory jumper

Use this 3-pin jumper top clear all the current data stored in the CMOS

memory.

Function Jumper Cap

Normal operation Short pins 1-2

Clear CMOS Short pins 2-3

JP2: Keyboard power on jumper

Use this 3-pin jumper to enable keyboard power on with hot keys or

password.

Function Jumper Cap

Enable keyboard power on Short pins 1-2

Disable keyboard power on Short pins 2-3

JP3: Audio/modem enable/disable jumper

Use this jumper to enable or disable the audio system and modem

integrated on the mainboard.

Function Jumper Cap

Enable audio/modem Short Pins 1-2

Disable audio/modem

Short pins 2-3

JP5: Set System bus frequency jumper (100 MHz)

Use this jumper to set the system bus frequency at auto-detect, or fixed

at 100 MHz.

Function Jumper Cap

Normal Short Pins 1-2

Force 100 MHz Short pins 2-3

1

2

3

JP2

1 2 3

JP1

1 2 3

JP3

1 2 3

JP5

10

JP6: Audio codec select jumper

Use this jumper to select if the system uses the audio codec chip

integrated on the mainboard, or an audio codec chip located on an

optional AMR card.

Function Jumper Cap

Turn on onboard codec Short Pins 1-2

Turn off onboard codec Short pins 2-3

JP9: Set System bus frequency jumper (133 MHz)

Use this jumper to set the system bus frequency at auto-detect, or fixed

at 133 MHz.

Function Jumper Cap

Normal Short Pins 1-2

Force 133 MHz Short pins 2-3

JP11: Set TV-out format jumper

Use this jumper to select the format of the TV-out connector.

Function Jumper Cap

Select NTSC format Short Pins 1-2

Select PAL format Short pins 2-3

JP12: Select IDT or Intel processor jumper

Use this jumper to select if you are installing an Intel processor or an IDT

processor in the socket-370 processor socket.

Function Jumper Cap

IDT processor Short Pins 1-2

Intel processor Short pins 2-3

1 2 3

JP6

1 2 3

JP9

1 2 3

JP11

1 2 3

JP12

11

Before You Begin

Before you begin to install your MS7012D mainboard, take some

precautions to ensure that you avoid the possibility of damage to the

product from static electricity. Ensure too that you are installing the

mainboard into a suitable case.

Static Electricity

In adverse conditions, static electricity can accumulate and discharge

through the integrated circuits and silicon chips on this product. These

circuits and chips are sensitive and can be permanently damaged by

static discharge.

♦ If possible wear a grounding wrist strap clipped to a safely

grounded device during the installation.

♦ If you don’t have a wrist strap, discharge any static by touching

the metal case of a safely grounded device before beginning the

installation.

♦ Leave all components inside their static-proof bags until they are

required for the installation procedure.

♦ Handle all circuit boards and electronic components carefully.

Hold boards by the edges only. Do not flex or stress circuit

boards.

Choosing a Case

This a full-sized ATX mainboard that measures 305mm x 243mm. It has

5 PCI expansion slots and an AMR slot. The mainboard will fit most ATX

cases that are designed for full-sized ATX mainboards. With a full set of

expansion slots and support for 4 IDE devices, you might like to choose

a case that has a robust power supply unit that delivers at least 250

watts.

Some features on the mainboard are implemented by cabling connectors

on the mainboard to indicators and switches on the system case. Ensure

that your case supports all the features required. The MS7012D

mainboard can support one or two floppy diskette drives and four

enhanced IDE drives. Ensure that your case has sufficient power and

space for all the drives that you intend to install.

12

The mainboard has a set of I/O ports on the rear edge. Ensure that your

case has an I/O template that supports the I/O ports and expansion slots.

How to Set Jumpers

A jumper consists of two or more pins mounted on the mainboard. Some

jumpers might be arranged in a series with each pair of pins numbered

differently. Jumpers are used to change the electronic circuits on the

mainboard. When a jumper cap is placed on two jumper pins, the pins

are SHORT. If the jumper cap is removed (or placed on just a single pin)

the pins are OPEN.

This illustration shows a 2-pin jumper. When the

jumper cap is placed on both pins, the jumper is

SHORT. If you remove the jumper cap, or place the

jumper cap on just one pin, the jumper is OPEN.

This illustration shows a 3-pin jumper. The jumper cap is

placed on pins 2 and 3, so this jumper setting is SHORT

PINS 2-3.

This illustration shows the same 3-pin jumper. The jumper

cap is placed on pins 1 and 2, so this jumper setting is

SHORT PINS 1-2.

In this manual, all the jumper illustrations clearly show the

pin numbers. When you are setting the jumpers, make sure that the

jumper caps are placed on the correct pins to select the function or

feature that you want to enable or disable.

SHORT

OPEN

13

Preparing the Mainboard

Mainboard Guide

Use the following illustration and key to identify the components on your

mainboard.

JP2

CASFAN1

CPUFAN1

DIMM1

DIMM2

LED2

PWRFAN1

JP9

FDD1

IDE2

IDE1

PANEL1

SIR1

WOM1

WOL1

JP1

JP3

SPDIF1

J8

JP6

AMR Slot

TV1

J4

J5

Slot-1

Socket-370

PCI1

PCI2

PCI3

PCI4

PCI5

ATX1

COM2

LED1

J6

JP5

J7

JP12

JP11

14

Key to Mainboard Components

Component Description

Slot-1 Slot for Slot-1 processor cartridge

Socket-370

Socket for PPGA Celeron Processor

PCI 1,2,3,4,5

Five 32-bit PCI Slots

AMR Slot

Slot for an Audio Modem Riser card.

DIMM 1, 2

Two slots for 168-pin SDRAM memory module

FDD1

Connector for floppy disk drives

IDE1, IDE2

Primary and secondary IDE channels

ATX1

Connector for ATX power supply

PANEL1

Panel connector for switches and indicators

WOM1

Connector for modem wake up

WOL1

Connector for LAN wake up

SIR1

Connector for infrared port

SPDIF

SPDIF In/out connector (24-bit digital audio interface)

TV1

Connector for optional TV-out extension bracket

COM2

Connector for serial port 2/4

CASFAN1

Power connector for case cooling fan

CPUFAN1

Power connector for CPU cooling fan

PWRFAN1

Power connector for power supply cooling fan

J6

Case open detect connector

J8

Onboard modem connector

J4

Audio connector for CD-ROM/DVD drive

J5

Auxiliary audio connector for CD-ROM/DVD drive

J7

Auxiliary USB Ports connector

JP1

Clear CMOS memory jumper

JP2

Keyboard power on jumper

JP3

Audio/modem enable/disable jumper

JP5

Set system bus frequency jumper (100 MHz)

JP6

Select onboard audio codec or AMR audio codec

JP9

Set system bus frequency jumper (133 MHz)

JP11

Set TV-out format jumper

JP12

Select IDT or Intel processor jumper

LED1*

Suspend-to-RAM indicator

LED2**

Suspension Indicator

*LED1

This red indicator turns on if your system is suspended to RAM. In a

suspend to RAM, the system turns off most of the power-consuming

components except for the 3.3V required to refresh the memory. If LED1

is turned on, it warns you that the computer is suspended to RAM and a

refresh current is passing through the memory modules. You should not

attempt to remove or install memory modules when LED1 is turned on.

15

**LED2

This red indicator turns on whenever system is turned on. The LED

warns users not to work on the mainboard, for example adding

expansion cards or changing jumpers, because the system is still active.

I/O Ports Side View

PS2KBM

USB1

COM1

VGA1

J3

LPT1

Key to I/O Ports

Component Description

PS2KBM PS/2 port for pointing device (upper port)

PS/2 port for keyboard (lower port)

LPT1 External parallel port

J3 (Upper)

External game/MIDI port

J3 (Lower)

Audio jacks for (left to right) line out, line in,

microphone

VGA1

External monitor port

COM1

Serial port COM1/3

USB1 Two stacked Universal Serial Bus ports

16

Check the Jumper Settings

Check all the mainboard jumpers to ensure that the board is configured

correctly.

JP1 Clear CMOS Memory Jumper

This jumper lets you erase the system setup settings that are stored in

CMOS memory. You might need to erase this data if incorrect settings

are preventing your system from operating. To clear the CMOS memory,

turn off the system, disconnect the power cable from the mainboard, and

short the appropriate pins for a few seconds.

Function Jumper Cap

Normal Operation Short pins 1-2

Clear CMOS Short pins 2-3

JP2: Keyboard Power On Jumper

This jumper lets you use a typed-in password as a power switch to turn

your system on. If you enable this property, you need to define the

password or the hot keys using the setup utility. See Chapter 3.

Function Jumper Cap

Disable keyboard power on

Short pins 1-2

Enable keyboard power on Short pins 2-3

JP2

1

2

3

JP1

1 2 3

JP2

JP1

JP6

JP3

JP12

JP11

JP9

JP5

Page is loading ...

MATSONIC MS7012D User manual

MATSONIC MS7012D User manual

Related papers

Other documents