Page is loading ...
Model: AF-T1B
HD WIRELESS SOUND FOR YOUR HDTV
QUICKSTART GUIDE
www.MEEaudio.com/Connect
universal dual bluetooth
®
wireless audio transmitter
For Headphones and Speakers
Scan QR code or enter the URL
below into your web browser:
MEEaudio.com/ConnectVid
CONNECT SUPPORT GUIDE
Ensure the
micro-USB power
cable is plugged
into the micro-USB
POWER port of the
Connect
.
Plug the USB end
of the cable into an
AC adapter, TV, or
computer USB port.
Put your Bluetooth headphones in pairing
mode.
Consult the user manual of your
Bluetooth headphones if you are not
sure how to put them in pairing mode
Once the headphones are in pairing mode,
click Pairing button “A” once to put the
Connect
in pairing mode.
Put the second headphone in pairing
mode.
Consult the user manual of your
Bluetooth headphones if you are not
sure how to put them in pairing mode
Once the headphones are in pairing mode,
click Pairing button “B” once to put the
Connect
in pairing mode.
Blinking blue light will change to solid blue
light once successfully paired.
OPTIONAL: PAIR WITH
2ND BLUETOOTH HEADPHONES
Remove protective caps
from both ends of the
digital optical S/PDIF
audio cable
Plug digital optical
S/PDIF audio cable
into the OPTICAL
audio input of
the
Connect
.
Plug the other end into
the TV’s DIGITAL AUDIO
OUT (OPTICAL) port.
Plug 3.5 mm audio cable into the
3.5 mm audio input of the
Connect
.
Plug the other
end into the TV’s
headphone jack.
Headphone jack may be located on
rear, side, front, or bottom of TV.
ADJUSTING VOLUME
Choose
ONLY ONE
audio cable supported by your TV
STEP 2 STEP 3
STEP 1
STEP 4
SUBSEQUENT USE
A OFF ON
A OFF ON
Slide the ON/OFF switch to
the ON position.
CLICK
PAIRING
BLINKING BLUE LIGHT
PAIRED
SOLID BLUE LIGHT
PAIRING SIDE “B”
BLINKING BLUE LIGHT
TWO HEADPHONES PAIRED
TWO SOLID BLUE LIGHTS
B
CLICK
1.
2.
1.
2.
PAIR WITH BLUETOOTH HEADPHONES
GETTING STARTED
CHOICE A: OPTICAL CHOICE B: 3.5 MM
CHOICE C: RCA
POWER ON
1.
2.
3.
Proceed to
4.
OR OR
1.
2.
3.
1.
2.
1.
2.
1.
2.
OPTICAL
DIGITAL AUDIO OUT
Plug red/white ends of RCA audio cable
into the TV’s red/white RCA AUDIO OUT
port.
Plug 3.5 mm end of RCA audio cable into
the 3.5 mm audio input of the
Connect
.
Change audio output settings to “VARIABLE”.
Set TV’s internal speakers to “OFF”.
**Exact menu and item names may vary
between TVs.
AUDIO OUT
R L
settings
sound / audio
Analog audio out
fixed
variable
settings
sound / audio
tv speakers
on
off
STEP 2
3.
If you need to pair a second Bluetooth
headphone, see below. Otherwise,
proceed to
STEP 3
Blinking blue light will change to solid
blue light once successfully paired.
Test for sound. Make sure the volume on both
your TV and headphones is turned up.
5.
4.
Proceed to
STEP 4
3.
Proceed to
STEP 4
3.
Proceed to
STEP 3
A second set of Bluetooth headphones can
be paired after one is already connected.
Change Sound Output to “Optical”**
Change Digital Audio Output Format to
“STEREO” or “PCM”**
†
This may also need to done in the audio
output settings menu(s) of your streaming
app(s) and/or device(s) such as Apple TV
®
**Exact menu and item names may vary
between TVs.
†
On some TVs settings may be located in
“Advanced settings” or “Expert settings”
submenus.
1.
2.
settings
expert settings
Audio Output format
auto
dolby digital
pcm / stereo
DTS
settings
Sound / Audio
sound Output
hdmi
optical
tv speaker
NO SOUND? CHECK YOUR TV SETTINGS.
4.
Proceed to
STEP 4
Test for sound. Make sure the volume on
both your TV and headphones is turned up.
If you are using the Optical cable, you may
mute the TV speakers, which allows you to
directly control the volume on your
Bluetooth headphones.
Maximize the volume level on your TV, then
use volume controls on headphones to
adjust to preferred volume.
WHEN FINISHED, power off headphones
until next use
3.
Test for sound. Make sure the volume on
both your TV and headphones is turned up.
RCA jacks on TV must be designated
an AUDIO OUT. RCA input jacks,
commonly labeled AV IN, INPUT, or
COMPONENT will not work.
4.
3.
Proceed to
STEP 4
NO SOUND? CHECK YOUR TV SETTINGS.
3.
Proceed to
STEP 4
Volume max vol+
WHEN READY TO USE AGAIN, POWER ON THE
HEADPHONES AND THEY WILL RECONNECT
AUTOMATICALLY.
Do not put the Connect or your
headphones into pairing mode.
A solid blue light on the Connect will indicate
that a connection has been re-established.
COMPLETE ALL 4 STEPS. REMEMBER TO PLUG IN ONE POWER CABLE AND ONE AUDIO CABLE
NEED HELP?
VIEW OUR VIDEO SETUP GUIDE
Scan QR code or enter the URL
below into your web browser:
MEEaudio.com/ConnectVid
RCA
audio cable
Digital optical S/PDIF
audio cable
Micro-USB
power cable
3.5mm
audio cable
PACKAGE CONTENTS:
OVERVIEW:
Micro-USB POWER port
ON/OFF switch
Pairing
button “A”
Pairing
button “B”
OPTICAL audio input
3.5 mm
audio input
The status of the
Connect
is shown by a green power / charging
indicator light on the rear of the unit and two blue indicator lights on
the top as follows:
INDICATOR LIGHT (S)
USB Power plugged in,
green power indicator light solid
USB Power plugged in,
green power indicator
light pulsing slowly
USB Power not plugged in,
green power indicator light solid
USB Power not plugged in,
green power indicator
light blinking rapidly
Blue light blinking
One solid blue light
Two solid blue lights
CONNECT STATUS
Battery full
Charging
Powered on
Low battery
Pairing mode active
One Bluetooth device is connected
Two Bluetooth
devices are connected
LED INDICATOR LIGHTS
SAFETY AND CARE
Battery performance will be severely decreased when stored in
extreme temperatures: below -10°C/14°F or above 45°C/113°F
including direct sunlight.
The lifetime of the battery will be significantly reduced if your device
is not charged for a long time. It is recommended to charge your
device at least once a month.
Clean with a soft, slightly damp cloth.
Do not use chemical cleaners.
There are no user replaceable/reparable parts in this device.
Disassembling it will void your warranty.
•
•
•
•
WARNINGS
This device is designed and manufactured to operate within its
defined design limits. Misuse may result in electric shock or fire.
Read and follow these instructions carefully.
To prevent fire or shock hazards, do not expose this unit to rain or
moisture. If the device comes in contact with liquids, quickly wipe
away. If submersed in water, do not turn the device on until
completely dried. Note: liquid submersion voids the warranty.
Danger of explosion or fire if batteries are damaged. Keep away
from direct sunlight, naked flames, flammable gasses, or heat
sources such as radiators or stoves
Only use attachments/accessories specified by the manufacturer
Changes or modifications to this unit not expressly approved by
MEE audio could void the user’s authority to operate the equipment.
Keep the device and packaging out of reach of children.
•
•
•
FCC RULES
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
Relocate the receiving antenna.
Increase the separation between equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
•
•
•
•
MEE audio
and its logo are registered trademarks of S2E, Inc. All rights reserved.
The Bluetooth
®
word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.
and any use of such marks by MEE audio is under license. Other trademarks and trade
names are those of their respective owners.
Qualcomm
®
aptX
™
is a product of Qualcomm Technologies International, Ltd. Qualcomm is a
trademark of Qualcomm Incorporated, registered in the United States and other countries,
used with permission. aptX is a trademark of Qualcomm Technologies International, Ltd.,
registered in the United States and other countries, used with permission.
Apple TV
®
is a registered trademark of Apple Inc.
WARRANTY
MEE audio products purchased from authorized resellers are
covered by a 1-year manufacturer warranty. For more information,
visit MEEaudio.com/support
QUESTIONS?
• Get answers at MEEaudio.com/ConnectHelp
WE’RE HERE TO HELP!
Phone Support: 626-965-1008 x31
Monday ~ Friday 9am to 5:00pm PST
Email Support: [email protected]
All emails are responded to within 2 business days
FACTORY RESET/CLEAR MEMORY
To perform a factory reset of the
Connect
, hold Pairing button “A” for
approximately 5 seconds until the blue indicator light stops blinking.
All previously paired devices will be cleared from memory and a new
pairing will need to be created by following the procedure in STEP 2
STEP 2
VIEW OUR VIDEO SETUP GUIDE
Scan QR code or enter the URL below into
your web browser:
MEEaudio.com/ConnectVid
DISPOSAL AND RECYCLING
Dispose of this product in accordance with all local laws and
regulations. Because this product contains electronic components
and a battery, it must be disposed of separately from household
waste. Contact local authorities to learn about disposal and recycling
options.
ADDITIONAL INFORMATION
FOR ADDITIONAL SUPPORT
COMPLIANCE INFORMATION
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
/
