Raven SmarTrax Installation guide

Type
Installation guide
SmarTrax™ Installation Manual
AGCO RT-A Series
Massey Ferguson 64XX/74XX/76XX Series
and Challenger MT5X5B Series
While every effort has been made to ensure the accuracy of this document,
Raven Industries assumes no responsibility for omissions and errors. Nor is any
liability assumed for damages resulting from the use of information contained
herein.
Raven Industries shall not be responsible or liable for incidental or consequential
damages or a loss of anticipated benefits or profits, work stoppage or loss, or
impairment of data arising out of the use, or inability to use, this system or any of
its components. Raven Industries shall not be held responsible for any
modifications or repairs made outside our facilities, nor damages resulting from
inadequate maintenance of this system.
As with all wireless and satellite signals, several factors may affect the availability
and accuracy of wireless and satellite navigation and correction services (e.g.
GPS, GNSS, SBAS, etc.). Therefore, Raven Industries cannot guarantee the
accuracy, integrity, continuity, or availability of these services and cannot
guarantee the ability to use Raven systems, or products used as components of
systems, which rely upon the reception of these signals or availability of these
services. Raven Industries accepts no responsibility for the use of any of these
signals or services for other than the stated purpose.
Disclaimer
©Raven Industries, Inc. 2012, 2014
Table of Contents
Manual No. 016-5033-006 Rev. B i
Chapter 1 Important Safety Information................................................. 1
Hydraulic Safety ........................................................................................................................2
Electrical Safety ........................................................................................................................2
Chapter 2 Introduction............................................................................. 3
Preparing for Installation ...........................................................................................................4
Recommendations ..............................................................................................................4
Point of Reference ...............................................................................................................4
Updates .....................................................................................................................................4
Kit Contents ...............................................................................................................................5
Chapter 3 Hydraulic System Installation.............................................. 13
Remove the Cartridge from the SmarTrax Valve .....................................................................14
Install Fittings in the SmarTrax Valve ......................................................................................14
Mount the SmarTrax Valve ......................................................................................................16
Tractors with High Profile Cabs .........................................................................................16
Tractors with Low Profile Cabs ..........................................................................................17
Install the Left and Right Steering Hoses ................................................................................18
Install the Pressure Transducer ..............................................................................................20
Load Sense Steering Orbital .............................................................................................21
Open Center Steering Orbital ............................................................................................23
Install the Load Sense Hose ...................................................................................................24
Install the Pressure and Tank Hoses .......................................................................................26
Hydraulic Diagram ...................................................................................................................27
Chapter 4 Wheel Angle Sensor Installation........................................ 29
Assemble the Wheel Angle Sensor (WAS) .............................................................................29
Install the WAS ........................................................................................................................31
Chapter 5 Cab Component Installation................................................ 35
Install the SmarTrax Node .......................................................................................................35
Mount the SmarTrax Node ................................................................................................35
Node Mounting Locations ..................................................................................................37
Install the Foot Switch .............................................................................................................38
Install the Valve Harness .........................................................................................................38
Install the Chassis Cable - SmarTrax-Only Systems (If Applicable) ........................................42
Connect SmarTrax to an Existing Chassis Cable (If Applicable) ............................................42
System Diagrams ....................................................................................................................43
Table of Contents
ii AGCO RT-A Series, Massey Ferguson 64XX/74XX/76XX Series, Challenger MT5X5B Series SmarTrax™ Installation Manual
Chapter 6 Startup Procedures .............................................................. 47
Verify the SmarTrax System Installation ..................................................................................47
Calibrate the SmarTrax System ..............................................................................................48
CHAPTER
1
Manual No. 016-5033-006 Rev. B 1
C hapter 1
Important Safety
Information
Read this manual and the operation and safety instructions included with your implement and/or controller
carefully before installing the SmarTrax™ system.
Follow all safety information presented within this manual.
If you require assistance with any portion of the installation or service of your Raven equipment, contact
your local Raven dealer for support.
Follow all safety labels affixed to the SmarTrax system components. Be sure to keep safety labels in good
condition and replace any missing or damaged labels. To obtain replacements for missing or damaged
safety labels, contact your local Raven dealer.
When operating the machine after installing SmarTrax, observe the following safety measures:
Be alert and aware of surroundings.
Do not operate SmarTrax or any agricultural equipment while under the influence of alcohol or an illegal
substance.
Remain in the operator’s position in the machine at all times when SmarTrax is engaged.
Disable SmarTrax when exiting the operator’s seat and machine.
Do not drive the machine with SmarTrax enabled on any public road.
Determine and remain a safe working distance from other individuals. The operator is responsible for
disabling SmarTrax when the safe working distance has diminished.
Ensure SmarTrax is disabled prior to starting any maintenance work on SmarTrax or the machine.
When starting the machine for the first time after installing SmarTrax, be sure that all persons stand clear in
case a hose has not been properly tightened.
The machine must remain stationary and switched off during SmarTrax installation or maintenance.
NOTICE
WARNING
Chapter 1
2 AGCO RT-A Series, Massey Ferguson 64XX/74XX/76XX Series, Challenger MT5X5B Series SmarTrax™ Installation Manual
Hydraulic Safety
Raven Industries recommends that appropriate protective equipment be worn at all times when working on
the hydraulic system.
Never attempt to open or work on a hydraulic system with the equipment running. Care should always be
taken when opening a system that has been previously pressurized.
When disconnecting the hydraulic hoses or purging is required, be aware that the hydraulic fluid may be
extremely hot and under high pressure. Caution must be exercised.
Any work performed on the hydraulic system must be done in accordance with the machine manufacturer’s
approved maintenance instructions.
When installing SmarTrax hydraulics or performing diagnostics, maintenance, or routine service, ensure
that precautions are taken to prevent any foreign material or contaminants from being introduced into the
machine’s hydraulic system. Objects or materials that are able to bypass the machine’s hydraulic filtration
system will reduce performance and possibly damage the SmarTrax valve.
Electrical Safety
Always verify that the power leads are connected to the correct polarity as marked. Reversing the power
leads could cause severe damage to the equipment.
Ensure that the power cable is the last cable to be connected.
CAUTION
CHAPTER
2
Manual No. 016-5033-006 Rev. B 3
C hapter 2
Introduction
Congratulations on your purchase of the SmarTrax system! This system is designed to provide cutting-edge,
hands-free steering of the machine via Global Positioning System (GPS) coordinates.
This manual applies to the following machines:
MAKE: AGCO
MODEL: RT100, RT120, RT135, RT150
RT100A, RT110A, RT120A, RT140A, RT155A, RT165A, RT180A
MAKE: Massey Ferguson
MODEL: 6465, 6475, 6480, 6485, 6490, 6495, 6497, 6499
7465, 7475, 7480, 7485, 7490, 7495
7619, 7620, 7622, 7624
MAKE: Challenger
MODEL: MT525B, MT535B, MT545B, MT555B, MT565B, MT575B, MT595B
FIGURE 1. AGCO RT-A Series, Massey Ferguson 64XX/74XX/76XX Series, Challenger MT5X5B Series
Chapter 2
4 AGCO RT-A Series, Massey Ferguson 64XX/74XX/76XX Series, Challenger MT5X5B Series SmarTrax™ Installation Manual
Preparing for Installation
Before installing the SmarTrax system, park the machine where the ground is level, clean, and dry. Turn off the
machine and leave it turned off for the duration of the installation process. Bleed pressure from the hydraulic
system by loosening the hydraulic fittings slowly, where applicable.
During the installation process, follow good safety practices. Be sure to carefully read the instructions in this
manual as you complete the installation process.
Recommendations
Raven Industries recommends the following best practices when installing or operating the SmarTrax system
for the first time, at the start of the season, or when moving the SmarTrax system to another machine:
Install the GPS antenna in the recommended location. Refer to the following table for the machine-specific
antenna mounting location.
Note: If your machine is not listed, install the antenna on the front-center of the cab..
Ensure the machine’s hydraulic filters have been recently changed and there are no issues with the
machine’s hydraulic system (e.g., pump issues, faulty hydraulic motors, fine metal deposits in the hydraulic
hoses, etc.).
Ensure the machine’s hydraulic system is using fresh oil and debris is flushed from the hydraulic hoses,
valves, and filters.
Raven Industries recommends the following best practices when installing the SmarTrax system:
Use part numbers to identify the parts.
Do not remove the plastic wrap from a part until it is necessary for installation.
Do not remove plastic caps from a part until it is necessary for installation.
Point of Reference
The instructions in this manual assume that you are standing behind the machine, looking toward the cab.
Updates
Software and manual updates are available on the Raven Applied Technology website:
http://www.ravenhelp.com
Machine Preset
Antenna X Position
(left to right)
Antenna Y Position
(from the rear wheel
axle to the antenna
position on the cab)
Antenna Z Position
(ground to top of
antenna)
MF64XX/74XX/MT5X5B AGCO RTA Centered 4 ft. 9 in/1.448 m 9 ft.10 in./2.997 m
2
Manual No. 016-5033-006 Rev. B 5
Introduction
Kit Contents
This section contains a list of the components that are included in the SmarTrax kit. Before beginning the
SmarTrax installation, compare the items in the kit with the components on this list. If you have questions about
the kit, contact your local Raven dealer.
Note: The SmarTrax node (P/N 063-0173-228) is sold separately. Contact your local Raven dealer for
ordering information.
At Raven Industries, we strive to make your experience with our products as rewarding as
possible. One way to improve this experience is to provide us with feedback on this manual.
Your feedback will help shape the future of our product documentation and the overall service
we provide. We appreciate the opportunity to see ourselves as our customers see us and are
eager to gather ideas on how we have been helping or how we can do better.
To serve you best, please send an email with the following information to
-AGCO RT-A Series, Massey Ferguson 64XX/74XX/76XX Series, Challenger MT5X5B Series
SmarTrax™ Installation Manual
-Manual No. 016-5033-006 Rev. B
-Any comments or feedback (include chapter or page numbers if applicable).
-Let us know how long have you been using this or other Raven products.
We will not share your email or any information you provide with anyone else. Your feedback
is valued and extremely important to us.
Thank you for your time.
TABLE 1. SmarTrax Installation Kit (P/N 117-5033-006)
Picture Item Description Part Number Qty.
Not Pictured
Manual - SmarTrax and SmartSteer
Calibration & Operation
016-0171-277 1
Not Pictured
Manual - AGCO RT-A Series, Massey
Ferguson 64XX/74XX Series, and
Challenger MT5X5B Series SmarTrax
Installation Manual
016-5033-006 1
Valve - Shuttle 334-0003-016 1
Chapter 2
6 AGCO RT-A Series, Massey Ferguson 64XX/74XX/76XX Series, Challenger MT5X5B Series SmarTrax™ Installation Manual
Valve - -6 JIC 5 PSI Check 334-0003-078 1
Valve - SmarTrax Hydraulic 334-0003-088 1
Bracket - Hydraulic Valve Mounting 107-0172-104 1
Bracket - Node Support 107-0172-105 1
Bracket - Rotary WAS (Large Axle) 107-0172-106 1
Bracket - Rotary WAS (Small Axle) 107-0172-107 1
Bracket - Node Mounting 107-0172-128 1
Bracket - Rotary WAS (Small Axle) 107-0172-181 1
Bracket - 5” Rotary WAS Arm Mounting 116-0159-721 1
Bracket - 4” Rotary WAS Arm Mounting 116-0159-722 1
Sensor - Rotary Wheel Angle 063-0181-024 1
TABLE 1. SmarTrax Installation Kit (P/N 117-5033-006)
Picture Item Description Part Number Qty.
2
Manual No. 016-5033-006 Rev. B 7
Introduction
Cable - Node Harness 115-4001-126 1
Cable - Valve Harness 115-4001-132 1
Cable - 12-pin Deutsch Adapter Cable 115-4001-219 1
Assembly - SmarTrax Enable Foot Switch 063-0172-470 1
Mount - M10 Ball Linear Sensor 103-0001-029 1
Mount - M10 Stud Linear Sensor 103-0001-030 1
Rod - M10 x 1.5 Threaded WAS Linkage 107-0172-125 1
Transducer - 0-3000 PSI Pressure 422-0000-086 1
Clamp - U-Bolt Muffler 435-3003-053 1
U-Bolt - 3/4” W x 1-1/4” L x 1/4”-20 Thread 107-0172-102 2
Bolt - 1/4”-20 UNC x 1” Hex 311-0050-105 1
TABLE 1. SmarTrax Installation Kit (P/N 117-5033-006)
Picture Item Description Part Number Qty.
Chapter 2
8 AGCO RT-A Series, Massey Ferguson 64XX/74XX/76XX Series, Challenger MT5X5B Series SmarTrax™ Installation Manual
Bolt - 5/16”-18 UNC x 3/4” Hex 311-0052-103 4
Bolt - 5/16”-18 UNC x 1-1/4” Hex 311-0052-106 2
Bolt - M8 x 1.25 x 25 mm Metric Hex 311-0070-001 2
Screw - 1/4”-20 Knurled Cup Hex Socket
Head Set
311-0015-729 2
Nut - 1/4”-20 Zinc Flanged Lock 312-1001-168 5
Nut - 5/16”-18 Flanged Lock Nut 312-1001-169 2
Nut - M10 x 1.5 x 5 mm Jam 312-1002-035 2
Nut - 3/8”-16 Nylon Insert Lock 312-4000-061 2
Nut - M10 x 1.5 Nylon Insert Lock 312-4000-208 1
Nut - 3/8”-16 Nylon Insert Thin Lock 312-4001-109 3
Washer - 5/16” Split Lock 313-1000-019 4
TABLE 1. SmarTrax Installation Kit (P/N 117-5033-006)
Picture Item Description Part Number Qty.
2
Manual No. 016-5033-006 Rev. B 9
Introduction
Washer - 5/8” Split Lock 313-1000-045 2
Washer - 5/16” Flat 313-2300-011 2
Washer - 3/8” Flat 313-2300-013 5
TABLE 2. Hydraulic Kit (P/N 117-0199-012)
Picture Item Description Part Number Qty.
Guard - 6” Hydraulic Hose with Cable Ties 214-3000-001 2
Fitting - -6 JIC (M) to -6 SAE O-Ring (M)
Straight Adapter
333-0012-045 2
Fitting - -4 SAE O-Ring (M) Plug 333-0012-051 2
Fitting - -6 ORFS M/F 90° Swivel Elbow 333-0012-065 2
Fitting - -6 JIC (M) to -6 SAE O-Ring (M)
Straight Adapter
333-0012-086 1
Fitting - -6 SAE O-Ring (M) Plug 333-0012-104 2
Fitting - -8 SAE O-Ring (M) Plug 333-0012-211 1
TABLE 1. SmarTrax Installation Kit (P/N 117-5033-006)
Picture Item Description Part Number Qty.
Chapter 2
10 AGCO RT-A Series, Massey Ferguson 64XX/74XX/76XX Series, Challenger MT5X5B Series SmarTrax™ Installation Manual
Fitting - -6 ORFS (M) to -10 SAE O-Ring (M)
Straight Adapter
333-0012-233 2
Fitting - -4 NPT (F) to -6 JIC (F) Straight
Adapter
333-0012-311 1
Fitting - -10 ORFS (M) to -8 SAE O-Ring (M)
Straight Adapter
333-0012-352 2
Fitting - -4 JIC (M) x -4 NPT (M) x -4 JIC (M)
Branch Tee Adapter
333-0012-353 1
Fitting - -4 NPT (M) to -4 SAE O-Ring (F)
Straight Adapter
333-0012-354 1
Fitting - 12L, M18 x 1.5 M/M/F Swivel Run
Tee Adapter
333-0012-356 1
Fitting - 18L, M26 x 1.5 M/M/F Swivel Run
Tee Adapter
333-0012-357 2
Fitting - 15L, M22 x 1.5 M/M/F Swivel Run
Tee Adapter
333-0012-361 1
Fitting - 8L, M14 x 1.5 M/F 90° Swivel Elbow 333-0012-367 1
Fitting - 15L, M22 x 1.5 (F) to -6 JIC (M)
Straight Adapter
333-0012-378 1
Fitting - 12L, M18 x 1.5 (M) to -8 BSPP (M)
Straight Adapter
333-0012-395 2
TABLE 2. Hydraulic Kit (P/N 117-0199-012)
Picture Item Description Part Number Qty.
Manual No. 016-5033-006 Rev. B 11
Introduction
Hydraulic Hose - -10 ORFS (F) 90° to18L,
M26 x 1.5 (F) - 36”
214-1000-860 2
Hydraulic Hose - -6 ORFS (F) 45° to 12L,
M18 x 1.5 (F) 122”
214-1000-861 2
Hydraulic Hose - -6 JIC (F) to 10L, M16 x 1.5
(F) 90° - 122”
214-1000-862 1
Hydraulic Hose - -4 JIC (F) to 8L, M14 X 1.5
(M) - 6”
214-1000-863 1
Hydraulic Hose - -4 JIC (F) to 8L, M14 X 1.5
(F) - 6”
214-1000-864 1
TABLE 2. Hydraulic Kit (P/N 117-0199-012)
Picture Item Description Part Number Qty.
Chapter 2
12 AGCO RT-A Series, Massey Ferguson 64XX/74XX/76XX Series, Challenger MT5X5B Series SmarTrax™ Installation Manual
CHAPTER
3
Manual No. 016-5033-006 Rev. B 13
C hapter 3
Hydraulic System
Installation
WARNING
Hydraulics are under pressure. Care should
always be taken with a system that has been
pressurized.
Before beginning the SmarTrax hydraulic
installation, turn off the machine and relieve
pressure by turning the steering wheel left and
right.
Never work on a hot machine. Always allow it to
cool before performing diagnostics,
maintenance, or routine service.
When disconnecting or purging hydraulic
hoses, be aware that the hydraulic fluid within
the machine’s system may be extremely hot
and under high pressure.
Tampering with hydraulic valves may cause
serious injury or death, and will void the
warranty.
CAUTION
When installing SmarTrax hydraulics or
performing diagnostics, maintenance, or routine
service, ensure precautions are taken to
prevent any foreign material from being
introduced into the machine’s hydraulic system.
Object or materials that are able to bypass the
machine’s hydraulic filtration system will reduce
performance and possibly damage the
SmarTrax hydraulic valve.
Chapter 3
14 AGCO RT-A Series, Massey Ferguson 64XX/74XX/76XX Series, Challenger MT5X5B Series SmarTrax™ Installation Manual
Remove the Cartridge from the SmarTrax
Valve
FIGURE 1. Cartridge Removed from the SmarTrax Valve
Before installing the hydraulic fittings in the SmarTrax valve (P/N 334-0003-088), remove the cartridge in Port
EP1 of the valve.
Note: This cartridge is not used in the SmarTrax system for the machines listed in this manual. Keep the
cartridge for future use.
Install Fittings in the SmarTrax Valve
Before mounting the SmarTrax valve (P/N 334-0003-088) on the machine, install the proper fittings in the
valve. This prepares the valve for installation and simplifies the hose connection process later in the procedure.
NOTICE
The appearance of the SmarTrax hydraulic
valve may vary slightly from the images
contained in this manual. However, the fittings,
hose connections, and cable connections
remain the same.
3
Manual No. 016-5033-006 Rev. B 15
Hydraulic System Installation
FIGURE 2. Fittings Installed in the SmarTrax Valve
Fitting Part Number Port
Fitting - -6 JIC (M) to -6 SAE O-Ring (M) Straight Adapter 333-0012-045 LSPV
Fitting - -4 SAE O-Ring (M) Plug 333-0012-051 PS
Fitting - -6 SAE O-Ring (M) Plug 333-0012-104 LS STEER
Fitting - -8 SAE O-Ring (M) Plug 333-0012-211 EP1
Fitting - -6 ORFS (M) to -10 SAE O-Ring (M) Straight Adapter 333-0012-233 A, B
Fitting - -6 ORFS M/F 90° Swivel Elbow 333-0012-065 A, B
Fitting - -10 ORFS (M) to -8 SAE O-Ring (M) Straight Adapter 333-0012-352 P, T
Chapter 3
16 AGCO RT-A Series, Massey Ferguson 64XX/74XX/76XX Series, Challenger MT5X5B Series SmarTrax™ Installation Manual
Mount the SmarTrax Valve
FIGURE 3. Potential Valve Mounting Positions
Determine the ideal valve mounting position on the machine based on the cab’s configuration, then refer to the
applicable section below to mount the SmarTrax valve (P/N 334-0003-088) in the desired location.
Tractors with High Profile Cabs
FIGURE 4. Mounting Bracket Installed
1. Mount the SmarTrax valve (P/N 334-0003-088) on the valve mounting bracket (P/N 107-0172-104) using
four 5/16”-18 x 3/4” hex bolts (P/N 311-0052-103) and four 5/16” lock washers (P/N 313-1000-019).
Note: The valve should be aligned so that the valve controller is parallel with the arm of the mounting
bracket.
POSITION 1 - High
profile cabs only
POSITION 2 - High or low
profile cabs
POSITION 3 - Use when
no weld nuts are present.
Use the valve mounting
bracket as a template to
drill holes.
Mounting Bracket
Arm
Valve Controller Parallel
with Mounting Bracket
Arm
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58

Raven SmarTrax Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI