Microh LED Quadpar TRI MKII User manual

Brand: Microh

Model: LED Quadpar TRI MKII

Category: Stroboscopes & disco lights

Type: User manual

TABLE OF CONTENTS

1. INTRODUCTION AND UNPACKING 1

2. SAFTEY INSTRUCTIONS 1-2

3. OPERATION INSTRUCTIONS 2-4

4. MOUNTING AND INSTALLATION 5

5. DMX-512 CONTROL CONNECTIONS 6

6. PHOTOMETRIC DATA 7

7. MENU NAVIGATION 8

8. DMX CHANNELS 9-13

9. KEY FEATURES 14

10. TECHNICAL SPECIFICATIONS 14

11. MAINTENANCE AND CLEANING 15

1. INTRODUCTION AND UNPACKING

Thank you for purchasing the MICROH LED QUADPAR MKII wash fixture. For your own safety and knowledge, please read this

manual before installing or operating the device. This manual covers the important information on installation and applications.

Please install and operate the fixture according to instructions. Meanwhile, please keep this manual for future reference.

The MICROH LED QUADPAR MKII pack-and-go LED wash par system is made of a new type of high temperature cast aluminum

casing. The fixture is designed and manufactured strictly following CE standards, complying with international standard DMX512

protocol. This fixture is applicable but not limited to large-scale live performances, theater, studio, nightclubs and discos.

The MICROH LED QUADPAR MKII wash fixture uses 436 powerful 10mm LED’s (109 per head – 20 Red, 52 Green, 37 Blue)

swhich feature high brightness and stability. Please carefully unpack it when you receive the fixture and check if it was damaged

during the transportation. And please check whether the following items are included inside the box:

Par Bar – One 4-Pedal Foot Switch – One Adjustable Tripod – One Power Cord – One

Bag for Par Bar – One Bag for Tripod Stand – One Foot Switch Controller Cable – One User Manual - One

2. SAFTEY INSTRUCTIONS

This device has left the factory in perfect condition. In order to maintain this condition and to ensure safe operation, it is absolutely

necessary for the user to follow the safety instructions and warning notes written in this user manual.

If the device has been exposed to temperature changes, do not switch it on immediately. The arising condensation could damage

the device. Leave the device switched off until it has reached room temperature, and is dry.

This device falls under protection-class I, therefore it is essential that the device be grounded. The electrical connection must be

carried out by a qualified technician.

The device should only be used with rate voltage and frequency. Make sure that the available voltage is not higher than 120V as

stated at the end of this manual.

Make sure the power cord is never crimped or damaged in any way, as this could cause shock and damage. If your power chord is

damaged in any way, please purchase a new cable from your local MICROH dealer. Always disconnect power, when the device is

not in use or before cleaning it. Never pull out the plug by tugging the power cord.

During initial start-up, some smoke or smell may arise. This is a normal process, and does not necessarily mean that the device is

defective. It should decrease gradually. Please do not project the beam onto combustible substances.

Fixtures cannot be installed on or near combustible substances. Keep more than 50cm distance from wall for proper ventilation and

air flow. If your fixture is or has become damaged in any way, it shall be exclusively replaced or repaired by the manufacturer to

avoid any hazard.

3. OPERATION INSTRUCTIONS

- Do not turn on the fixture if it has been through severe temperature differences. Damage may occur to the fixture. Wait until unit is

at room temperature to operate.

- The unit should be protected from any tremor or agitation during transport.

- Do not expose the fixture in any excessive heat, moisture or any environment with too much dust when installing. Do not lay any

power cables on the floor. It may cause electronic shock or damage to persons or equipment.

- Make sure to attach the safety chain and ensure the screws are properly screwed in when installing the fixture.

- Make sure the lens is in good condition. It is recommended to replace the unit if there are any damages or severe scratches.

- Make sure the fixture is operated and installed by qualified personnel.

- Keep the original packaging in case of defective product.

- Any non-manufacturer additions, modifications or changes in any way will void all warranty.

- Please do not attempt to open unit. It is only to be serviced by an authorized technician. If this occurs, or is apparent, the warranty

will be voided.

- The fixture’s warranty will be voided if there are any malfunctions from not following the user manual or any illegal operation (shock

short circuit, electronic shock, lamp broke, etc.)

-This fixture is equipped with 9 operating modes. 4 Pedal Foot Switch, Manual Colour Dimming, Built-in Program, Auto, Sound

Active, Master/Slave, DMX & IR Remote.

Press MODE and SET UP button simultaneously to run the auto-run program mode. To make the display stay on continuously,

press the MODE and UP buttons simultaneously. To make the display turn off after 20 seconds, press the MODE and DOWN

buttons simultaneously.

4-PEDAL FOOT SWITCH MODE

- In any mode, you will enter the foot pedal controller function when you set foot on any of the foot pedals. The functions for the

pedal are:

- 1.BLACK OUT is to turn off the light;

- 2.FREEZE is to lock the current condition;

- 3.SOUND ACTIVE is for sound active function;

- 4.PRESET is to select the built in programs and the static colours. The designed order is: program1 (static colour) → program2 →

program3 → program4 → program5 → program6 → program7 → program8 → program9 → program10 → program11 → program12

→ auto run → red → green → blue → yellow → purple → cyan → white

Note: 1. Keep pressing the PRESET foot pedal, the fixture will run the program in the designed order by cycle.

2. When press the FREEZE foot pedal, the fixture will lock the current condition. Press the FREEZE foot pedal again, and

the fixture will continue running the previous program you have select.

3. When the fixture is in the foot pedal controller function, the LED digital display will show the current running program.

MANUAL COLOUR DIMMING MODE

- Press MODE button, press SETUP to choose colour and flash speed, red“r.×××”,green“G. ×××”, blue“b. ×××

- Press SETUP to choose different colour, Press UP or DOWN button to set the dimming rate (0-255).

- When “FS.XX” is displayed, press UP or DOWN to select flash speed 0-99, 0 is turn off flash,1 is the slowest,99 is the fastest.

BUILT-IN PROGRAM MODE

- Press MODE button to select built-in program mode, “Pr.XX” is displayed. Press SETUP button choose the program, the colour

jumping speed and flash speed, when “Pr.XX” is displayed, press UP or DOWN button to set the program 1-12, total 12 programs.

- When “SP.XX” is displayed, press UP or DOWN to set the jumping speed (1-99), when “FS.XX” is displayed, press UP or DOWN

to set the flash speed (0-99), “0”is turn off flash.

- Notice: “ Pr.01” is static colour select program. There are 8 colours to choose from. Press the SET UP button to enter the static

colour submenu. When “CL.-X” is displayed press UP or DOWN buttons to scroll through the static colours.

AUTO MODE

- Press MODE button, when ”AUTO.” is displayed, the built-in programs run one after another in a continuous loop.

- When “SP.XX” is displayed, press UP or DOWN to set the colour jumping speed (0-99), ”0”is turn off flash.

- When ”FS.XX” is displayed, press UP or DOWN button to adjust the strobe speed(0-99), ”0”is turn off flash.

SOUND ACTIVE MODE

- Press MODE button, ”SU.XX” is display, and then press UP or DOWN button to set the sound level (0-31). Under this mode, the

SETUP button does not function.

MASTER/SLAVE MODE

- To activate slave mode press MODE button, ”SLAU.” is displayed. Under this mode SET UP, UP and DOWN do not function.

DMX MODE

- Press MODE button. When “d.XXX” is displayed, press SET UP to choose the DMX address or DMX mode. When “d.XXX”is

displayed, press UP or DOWN to select the DMX address 1-512.

- When “d-P.X” is displayed, press UP or DOWN button to choose the DMX mode 1-7.When there is no controller signal, the

display will flash, and turn off.

IR REMOTE MODE

You may also operate this fixture by optional IR remote sold separately (LEDQUADPAR-REMOTE). Operating distance of 10M.

Notice: IR remote is ready to control the product which is in any working mode.

AUTO MODE: Press AUTO RUN to choose Auto mode. Press FLASH to turn on/off the flash of the

Auto Run, and then pressing “+” and “-“ buttons to adjust flash speed. Press SPEED to control the

speed of the Auto Run, and then pressing “+” and “-” buttons to adjust it.

BUILT-IN PROGRAM MODE: Press PROG to set built-in program mode. Press “+” or “-” to program

(Pressing FLASH /SPEED will change the strobe rate and speed of the program). Press FLASH to

turn on/off flash and press “+” or “-” to adjust the flash speed. Press SPEED to set the program

running speed and press “+” or “-” to adjust it. Notice: “ Pr.01” is a static colour program. There are 8

colours to choose from. Press the SPEED button to enter the static colour submenu, and then

pressing “+” and “-” buttons to scroll through the static colours.

SLAVE MODE: Press SL to display SLAVE mode. The R/G/B lights are off when without a master

light.

SOUND ACTIVE MODE: Press SA to display sound active mode, and pressing “+” and “-” buttons to

adjust sensitivity level.

MANUAL COLOUR DIMMING MODE: Press R/G/B to choose program mode, and press “+” and “-”

buttons to adjust the intensity of the light. Press FLASH to turn on/off flash effect, pressing “+” and “-”

buttons to adjust the flash speed.

DMX MODE: There are seven DMX modes: 2, 3, 4, 7, 8, 14, or 15 Channels. You must set the DMX Channel mode before you

address the fixture. To select your desired DMX Channel mode press the DMX mode button, and then press the “+” or “-” buttons to

scroll through the DMX Channel modes.

• If Red LED’s glow you are in DMX Mode 1: 3 DMX Channels

• If Green LED’s glow you are in DMX Mode 2: 4 DMX Channels

• If Blue LED’s glow you are in DMX Mode 3: 8 DMX Channels

• If Red and Green LED’s glow you are in DMX Mode 4: 14 DMX Channels

• If Red and Blue LED’s glow you are in DMX Mode 5: 2 DMX Channels

• If Green and Blue LED’s glow you are in DMX Mode 6: 15 DMX Channels

• If all the LED’s glow you are in DMX Mode 7: 7 DMX Channels

SETTING ADDRESS: Press S button to set the DMX address or initialize the program, then the red, green lights will flash 2~3

times. Please put in 3 numbers ,for example, 1 2 3. After the red light is on, please put in the first number. After the first number is

accessed the green light will be on, then put in the second number. When the blue light is on, please put in the third number. After

all the three numbers are entered, the red, green & blue lights will flash 2~3 times, which indicates that the DMX address is correct

and it entered the DMX MODE automatically. If the address is wrong the red light will be on. (Auto mode will be applied when

numbers 951 are pressed. The red & green light will turn on, press 0 to initialize auto program). If the address is greater than 512,

the red light will turn on, indicating new address should be put in. Then the system will run in the designated mode.

BLACK OUT MODE: Press BLACK OUT to set the LED lights power on or power off by pressing this button.

4. MOUNTING AND INSTALLATION

Caution: For added protection, mount the fixtures in areas outside walking paths, seating areas, or in areas were the fixture might

be reached by unauthorized personnel. Before mounting the fixture to any surface, make sure that the installation area can hold a

minimum point load of 10 times the device’s weight. Fixture installation must always be secured with a secondary safety attachment,

such as an appropriate safety cable. Never stand directly below the device when mounting, removing, or servicing the fixture.

Whether installing inverted on a truss or ceiling, or set on a flat level surface (see image below). Be sure this fixture is kept at least

0.5m (1.5 ft) away from any flammable materials (decoration etc.). Always use and install the supplied safety cable as a safety

measure to prevent accidental damage and/or injury in the event the clamp fails.

Mounting Points: Overhead mounting requires extensive experience, including calculating working load limits. A knowledge of the

installation material being used, and periodic safety inspection of all installation material and the fixture are all imperative and should

only be performed by a qualified technician. Improper installation can result in bodily injury and damage.

The MICROH LEDQUAD PAR SERIES can be mounted by using the pole mount on the base of the T bar. Be sure to complete all

rigging and installation procedures before connecting the main power cord to the appropriate wall outlet.

The MICROH LEDQUAD PAR SERIES has a folding bar mechanism that is easily released by gently pressing upward on the silver

clip in the middle base of the bar. Please see diagrams below.

5. DMX-512 CONTROL CONNECTIONS

This fixture complies with international USITT DMX standards and can be used with either a 3 pin or 5 pin DMX connector. Plug in

the provided 3 pin XLR cable to the female 3-pin XLR output of your controller and the other side to the male 3-pin XLR input of the

fixture. To connect the units to DMX, you must daisy chain the fixtures together as referred in the diagram below. Always end your

DMX-512 connection with a DMX terminator.

For installations where the DMX cable has to run a long distance, or is in an electrically noisy environment, it is recommended to

use a DMX terminator. This helps in preventing corruption of the digital control signal by electrical noise. The DMX terminator is

simply an XLR plug with a 120 Ω resistor connected between pins 2 and 3,which is then plugged into the output XLR socket of the

last fixture in the chain. Please see illustrations below.

PIN 3

PIN 2

6. PHOTOMETRIC DATA

7. MENU NAVIGATION

8. DMX CHANNELS

DMX mode 1：3 channel mode

CH No. DMX value Function

CH1 000~255 Red(dim→bright)

CH2 000~255 Green(dim→bright)

CH3 000~255 Blue(dim→bright)

DMX mode 2: 4 channel mode

CH No. DMX value Function

CH1 000~255 Master dimmer(dim→bright)

CH2 000~255 Red(dim→bright)

CH3 000~255 Green(dim→bright)

CH4 000~255 Blue(dim→bright)

DMX mode 3: 8 channel mode

CH No. DMX value Function

CH1 000~255 Master dimmer(dim→bright)

CH2 000 No function

001~255 Strobe(slow→fast)

CH3 000~255 Red panel 1&2(dim→bright)

CH4 000~255 Green panel 1&2(dim→bright)

CH5 000~255 Blue panel 1&2(dim→bright)

CH6 000~255 Red panel 3&4(dim→bright)

CH7 000~255 Green panel 3&4(dim→bright)

CH8 000~255 Blue panel 3&4(dim→bright)

DMX mode 4: 14 channel mode

CH No. DMX value Function

CH1 000~255 Master dimmer(dim→bright)

CH2 000 No function

001~255 Strobe(slow→fast)

CH3 000~255 Red panel 1(dim→bright)

CH4 000~255 Green panel 1(dim→bright)

CH5 000~255 Blue panel 1(dim→bright)

CH6 000~255 Red panel 2(dim→bright)

CH7 000~255 Green panel 2(dim→bright)

CH8 000~255 Blue panel 2(dim→bright)

CH9 000~255 Red panel 3(dim→bright)

CH10 000~255 Green panel 3(dim→bright)

CH11 000~255 Blue panel 3(dim→bright)

CH12 000~255 Red panel 4(dim→bright)

CH13 000~255 Green panel 4(dim→bright)

CH14 000~255 Blue panel 4(dim→bright)

DMX mode 5: 2 channel mode

CH1 CH2

0-11 off

No function

12-23 red

24-35 yellow

36-47 green

48-59 cyan

60-71 blue

72-83 purple

84-95 white

96-107 program 2

speed

0~stop

1~255（into99

grade,

1~2 is grade 1；more than 247 is grade

99；

slowfast）

108-119 program 3

120-131 program 4

132-143 program 5

144-155 program 6

156-167 program 7

168-179 program 8

180-191 program 9

192-203 program 10

204-215 program 11

216-227 program 12

228-239 auto-run

240-255 sound active Sound sensitive

0=OFF 1-255 into 31grade

DMX mode 6: 15 channel mode

CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 CH10 CH11 CH12 CH13 CH14 CH15

0-9

OFF

10-255

Master

dimmer

(dim→

bright)

0-9

RGB

dimmer

mode

strobe

0~9=

OFF

10~25

5=ON

（Slow

Fast

）

Red

(panel

Green

(panel

Blue

(panel

Red

(panel

Green

(panel

Blue

(panel

Red

(panel

Green

(panel

Blue

(panel

Red

(panel

Green

(panel

Blue

(panel

10-249

auto-

run

speed

0~stop

1~255

(into 99

grade,

1~2 is

grade;

than

247 is

grade;

Slow

fast）

No use

250-

255

sound

active

Sound

sensitiv

ity

0=OFF

1-255

into 31

grade

No use

No use No use No use No use No use No use No use No use No use No use

DMX mode 7: 7 channel mode

CH1 CH2 CH3 CH4 CH5 CH6 CH7

Master

Dimmer

0-255

(dim→

bright)

Red

0-255

(dim→

bright)

Green

0-255

(dim→

bright)

Blue

0-255

(dim→

bright)

0-11 off

No Function

12-23 red

strobe

0= OFF

1~255=ON

（SlowFast）

24-35 yellow

36-47 green

48-59 cyan

60-71 blue

72-83 purple

84-95 white

96-107 program 2

speed

0~stop

1~255（into99

grade,

1~2 is grade 1；more

than 247 is grade 99；

slowfast）

108-119 program 3

120-131 program 4

132-143 program 5

144-155 program 6

156-167 program 7

168-179 program 8

180-191 program 9

192-203 program 10

204-215 program 11

216-227 program 12

228-239 auto-run

240-255 sound active

Sensitivity

0=OFF 1-255 into

31grade

No FUNCTION

9. KEY FEATURES

- 109 x 10mm LEDs Per Head (20 Red, 52 Green, 37 Blue) (436 Total)

- 3 Pin XLR Input & Output

- Adjustable Tripod Stand

- 4-Pedal Foot Switch Operation

- IR Remote Optional Operation (LEDQUADPAR-REMOTE)

- Digital Display

10. TECHNICAL SPECIFICATIONS

MODEL: LED QUADPAR MKII

LAMP: 436 x 10mm LEDS (Per Head: 109 LEDs – 20 Red, 52 Green, 37 Blue)

VOLTAGE: 120VAC 60Hz 60W

FUSE: 120VAC 3A

DIMENSIONS (W x H): 47.2" x 94.5" (Max Height 9.8') / 120 x 240 cm (Max Height 3m)

CASE DIMENSIONS (lL x W x H): 29" x 14" x 7.5" (Max Height 9.8') / 737 x 356 x 191 mm

NET WEIGHT: 20.5 lbs / 9.3 kg

WARRANTY: 2 Year Limited Warranty

11. MAINTENANCE AND CLEANING

The following points have to be considered during the inspection:

1) All screws for installing the device, or parts of the device must be tightly connected, and must not be corroded.

2) There must not be any deformations on the housing, colour lenses, fixations or installation spots (ceiling, suspension, trussing).

3) Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances.

4）The electric power supply cables must not show any damage, material fatigue or sediments.

Further instructions depending on the installation spot and usage must be handled by a skilled installer or technician. Any safety

issues must be resolved.

In order to keep the fixture in good condition and extend the life, we suggest regular cleaning to the fixture.

1) Clean the inside and outside lens each week to avoid the light output from darkening due to accumulation of dust, dirt, etc.

2) Clean the fan each week.

3) A detailed electrical check by approved technician every three months is advised. Ensure the circuit contacts are in good

condition, and prevent from overheating.

We recommend a frequent cleaning of the device. Please use a moist, lint- free cloth. Never use alcohol or solvents.

There are no serviceable parts inside the device. Please refer to the instructions under “Installation instructions”.

Should you need any spare parts, please order genuine MICROH parts from your local dealer.

IF YOU SHOULD EXPERIENCE ANY PROBLEMS OR ISSUES PLEASE CONTACT MICROH PROFESSIONAL PRODUCTS BY

EMAIL AT [email protected]m

In the event that your unit is defective in any way, please contact your local dealer to obtain an RA number for service

repair.

DISCLAIMER – MICROH believes that the information contained within this user manual is accurate. However, Microh is

not responsible for any error or addendums to this manual. If you have any comments or general suggestions on how this

manual can be improved please contact info@microhpro.com. Thank you.

Microh LED Quadpar TRI MKII User manual

Brand: Microh

Model: LED Quadpar TRI MKII

Category: Stroboscopes & disco lights

Type: User manual

Download PDF

report

Microh LED Quadpar TRI MKII User manual

Microh LED Quadpar TRI MKII User manual

Related papers

Other documents