Phase Technology FP Series User manual

Phase Technology
Brand
Phase Technology
Model
FP Series
Category
Car kits
Type
User manual

This manual is also suitable for

Phase Technology Motion Sensor FP Series

Phase Technology Motion Sensor FP Series is a professional-grade audio activation device designed to trigger audio output based on motion detection. It offers two distinct motion sensor lens options: a wide lens for triggering audio activation from movement beyond the diameter of the dome and a narrow lens for triggering audio activation only when someone is standing directly underneath the dome.

Phase Technology Motion Sensor FP Series

Phase Technology Motion Sensor FP Series is a professional-grade audio activation device designed to trigger audio output based on motion detection. It offers two distinct motion sensor lens options: a wide lens for triggering audio activation from movement beyond the diameter of the dome and a narrow lens for triggering audio activation only when someone is standing directly underneath the dome.

Install Instructions For:
Motion Sensor
1.435.647.9555
|
800.647.TUBE
|
www.soundtube.com
FP Series
FP Series
FP Series
Do not spec or install speaker near support beam, ventilation
duct or other structure that may interfere with speaker function
or dispersion.
Warning Warning
SoundTube speakers must be installed by a professional audio
installer/contractor. For safety and for optimum audio performance,
installer must follow all directions issued by SoundTube Entertainment.
© 2005 SoundTube Entertainment, Inc. All rights reserved. PN INS-FP6-MS REV 01.12.06
Dome Clamp
FP Speaker Pod
Motion Sensor
lens (narrow)
Motion Sensor
lens (wide)
Motion Sensor
Motion Sensor
Pod Cover
Motion Sensor Accessory Contents
1 FP Pod with wide lens
1 Narrow lens
(Optional, included)
(Standard)
The FP pod comes with the motion sensor lens preset to a wide angle and will trigger audio
activation from movement beyond the diameter of the dome. For applications with a narrow motion
sensor angle, follow these instructions. The narrow motion sensor lens will trigger audio activation
only when someone is standing directly underneath the dome.
ATTENTION
2. Remove motion sensor
pod cover.
3. Remove motion sensor lens. 4. Place narrow lens into pod
cover. Make sure lens is flush
with outside of pod cover.
Align the flat side of the lens w/
the flat side of the pod cover.
5. Place pod cover back on
FP unit.
6. Complete.
Install Instructions For:
To adjust the sensor from wide angle to narrow angle:
Motion Sensor
1.435.647.9555
|
800.647.TUBE
|
www.soundtube.com
FP Series
FP Series
FP Series
1. Unpack FP speaker pod
and FP Dome.
Orange White /
Orange
Blue White (unused)
Green (unused)
Brown White /
Brown
White/Green Signal wire
for 5 Volt ttl signal
Power supply and voltage sensor control
not included.
1. Attach the +12 V from the power supply to the
Orange white and orange wire pair.
2. Attach the ground from the power supply to the brown
white and brown wire pair.
3. Attach the ground from the voltage sensor controller to
the brown and white wire pair also.
4. Attach the signal wire to the white/green single wire.
5 Volt ttl signal (White/Green Signal wire)
• 0 Volts = motion detected
• 5 Volts = no motion detected
• The green and blue/white
wires are unused.
1k to 12 Volt pullup (Blue Signal wire)
• 12 Volts = motion detected
• 0 Volts = no motion detected
• The green and blue/white
wires are unused.
Wiring Diagram for Motion Sensor
Power Source
Cat V Wire From Pod
Voltage Sensor Controller
Blue Signal wire for
1k to 12 Volt pullup
Signal wire
Ground
Ground
Positive
(not included)
(not included)
SD-25 Audio Repeater
Gilderfluke & Company
Burbank, califorina
Power
9-24 VDC
Line out
Left
Line out
right
Speakers
Left
Right
Power
9-24 vdc
Running
status
Inputs
A
B
Black Spk
Red Spk
Green Spk
White spk
Brown
White Brown
Cat V Pair
Orange
White Orange
Cat V Pair
Jumper wire
Pin 5 to 10
Blue
Cat V
(Signal)
12 VDC
Power
supply
Install Instructions For:
SoundTube/Gilderfluke SD-25
FP6030-M FP6020-M Wiring diagram
1.435.647.9555 | 800.647.TUBE | www.soundtube.com
FP SeriesFP Series
Notes
1- 12 VDC is the maximum power
input from the power supply if using
soundtube motion sensor
2- If more volume is needed the SD-25
can be bridged and run in mono
mode. Internal jumpers need to be
set for this mode. Please see Sd-25
configuration & installation
instructions.
3- For operating and playback modes
please see SD-25 installation sheet.
  • Page 1 1
  • Page 2 2
  • Page 3 3

Phase Technology FP Series User manual

Phase Technology
Brand
Phase Technology
Model
FP Series
Category
Car kits
Type
User manual
This manual is also suitable for

Phase Technology Motion Sensor FP Series

Phase Technology Motion Sensor FP Series is a professional-grade audio activation device designed to trigger audio output based on motion detection. It offers two distinct motion sensor lens options: a wide lens for triggering audio activation from movement beyond the diameter of the dome and a narrow lens for triggering audio activation only when someone is standing directly underneath the dome.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents