Grizzly G9929 Owner's manual

Brand: Grizzly

Model: G9929

Type: Owner's manual

This manual is also suitable for

G9930

Grizzly G9929 is a gun security safe designed to provide secure storage for up to 5 firearms. It features a combination lock for added security, and comes with two keys for the storage compartment. The safe is constructed from heavy-duty steel, and has been tested to withstand forced entry attempts. It also includes pre-drilled holes for mounting to a wall or floor, for added security and stability. With its durable construction and secure locking mechanisms, the Grizzly G9929 is an ideal choice for responsible gun owners who want to keep their firearms safe and secure.

Congratulations on your purchase of one of the best values in gun security safes. Responsible gun

ownership begins with the safe and secure storage of firearms when not in use.

After unpacking the box, consider carefully where

you want to place the safe. Choose a location

which is not obvious to an intruder and a place

where the safe can be firmly secured. Refer to the

mounting instructions below.

GUN SECURITY SAFES

INSTRUCTION SHEET

G9929 5 Gun Combination Lock

G9930 10 Gun Combination Lock & Key

This safe is extremely heavy and great care

should be taken when moving it into place.

The safe can tip forward when the door is

opened which can cause a crushing injury.

Before opening or moving safe, attach the

extension feet with the screws provided.

Once the final location for the safe has been

determined, it should be permanently

mounted to the building structure to avoid

inadvertent tipping or movement. Once

secured, the extension foot may be

removed. Serious personal injury may

occur.

MOUNTING INSTRUCTIONS

There are four holes through the back wall of the safe designed to allow bolting of the safe to a

structural component such as a concrete wall or a wall stud. Do not attempt to bolt the safe to plas-

ter or wall board as these can be easily broken out.

Position the safe where you want it, and mark the hole locations from inside the safe cabinet. Use

caution to make sure the safe is secured with the foot or other holding device so it cannot tip over.

Concrete wall anchors of various types can be purchased to allow installation against a concrete

wall. Follow the instructions for the type of fastener you purchased. It may be necessary to move

the safe out of the way to do the drilling.

Attach these safety feet to the front of the safe to avoid the possibility of the safe tipping forward.

Thread the locknut and rubber foot onto the bracket, then use two Phillips

head screws to attach

the bracket to the lower edge of the door frame. Adjust the rubber foot so it contacts the floor and

tighten the locknut.

MODEL #: ____________

KEY #: ______________

Combination:

#1 Left ____

#2 Right ____

#3 Left ____

#4 Right ____

MODEL #: ____________

KEY #: ______________

Combination:

#1 Left ____

#2 Right ____

#3 Left ____

#4 Right ____

OPENING INSTRUCTIONS

The combination for your safe is shown below. Please be sure to record this number in several

different places. For your safety and security, Grizzly does not retain a master record of the com-

bination numbers. In the event the combination is lost, you will need to contact a locksmith or safe

expert to open the safe. There is a special key required for opening the safe. Two copies of the

key are included with your safe, be sure to safely store away at least one of these keys.

To open the safe:

1. Turn the Dial Left (counterclockwise) at least four (4) turns, then line the first number (#1) up

with the index mark at the top of the Dial.

2. Turn the dial Right (clockwise) until the first number has gone past the index mark two times,

then line up the second number (#2) with the index mark when it comes around.

3. Turn the Dial Left (counterclockwise) one full revolution, then line up the third number (#3)

with the index mark on the next revolution.

4. Turn the Dial Right (clockwise) until the fourth number (#4) lines up with the index mark.

Do not go past the third number on this revolution.

5. Insert the key into the lock and turn the key Right (clockwise) (Model G9930 Only).

6. Turn the handle lever to the Right and pull on the door.

To lock the safe:

1. Close the door.

2. Turn the key to its original position and remove. (Model G9930 Only)

3. Rotate the Dial several turns in either direction.

There are also two separate keys provided which open the storage compartment in the safe. Be

sure to lock this compartment and remove the key before closing the safe door.

If you are putting the safe in a building which has plaster or sheetrocked walls, be sure to locate

the safe in a position where the mounting holes will line up with a wall stud. Locate the stud by

tapping on the wall or by using one of the several different devices to locate studs. Mark and drill

holes into the stud, making sure you are centered on the stud. Two lag bolts (not supplied) should

be used to secure the safe through the inside back of wall of the safe into the drilled holes.

Permanently mounting the safe also provides an extra measure of security in that it makes it very

difficult for a thief to take the entire unit. It also provides stability for the heavy weight of the safe

and will eliminate any tipping hazard.

Cut these out

and store in

two different

secure places.

Grizzly G9929 Owner's manual

Brand: Grizzly

Model: G9929

Type: Owner's manual

This manual is also suitable for

G9930

Download PDF

report

Grizzly G9929 Owner's manual

This manual is also suitable for

Grizzly G9929 Owner's manual

Related papers

Other documents