The Great Outdoors 72633-143C User manual

Brand: The Great Outdoors

Model: 72633-143C

Type: User manual

The Great Outdoors 72633-143C is a versatile and easy-to-install light fixture designed for both indoor and outdoor use. With its sturdy construction and weather-resistant design, this fixture is perfect for illuminating pathways, driveways, patios, and other outdoor areas. The 72633-143C features a circular strap for easy mounting to a variety of surfaces, and its adjustable design allows for customization of the light's angle and direction. The fixture's clear glass panel provides ample illumination, and its included candle covers add a touch of elegance to any setting.

INSTALLATION INSTRUCTIONS

For item#72633-143C (New. 12/11/2017)

READ AND SAVE THESE INSTRUCTIONS

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

Fig.1

Fig. 3

PREPARING FOR INSTALLATION (Fig. 1)

1. Shut off the power at the fuse box or circuit breaker. If

necessary, remove the old fixture, including the mounting

hardware.

2. Carefully unpack your new fixture, lay out all parts on a

clear area. Be careful not to lose any small parts necessary

for installation.

3. Thread the studs (C) into the pre-drilled holes of the circular

strap (A), spaced the same distance apart as the holes in

the back plate (D).

4. Attach the circular strap (A) to the outlet box using the

mounting screws (B) (Size: #8-32N*L0.5”). The side of the

circular strap (A) marked “GND” must face out.

5. The support cable is provided to support the weight of the

fixture while wiring. Align the fixture to circular strap (A) and

attach hook (L) on the end of support cable (K) into a slot

located on circular strap (A). Carefully allow the support

cable (K) to support the weight of the fixture while wiring.

(Fig 1)

CONNECTING THE WIRES (Fig. 2)

6. At this point, connect the fixture wires to outlet box wires as

shown in Fig. 2, making sure that all wire connectors are

secured. If your outlet box has a ground wire (green or bare

copper), connect the fixture’s ground wire to it. Otherwise,

connect the fixture’s ground wire directly to the circular

strap (A) using the green screw provided. After wires are

connected, tuck them carefully inside the outlet box.

COMPLETING THE INSTALLATION (Fig. 1)

7. Align back plate (D) onto studs (C) and secure with two ball

nuts (E).

8. To prevent moisture from entering the outlet box and

causing a shortage, use clear caulking (i.e. Indoor/Outdoor

silicone sealant) to outline the outside of fixture back plate

where it meets the wall leaving a space at the bottom to

allow moisture a means to escape (Fig.3).

9. Place the candle covers (H) over the sockets (G).

10. Install the glass panel (F) into fixture body (J) and secure

with the tabs provided.

11. Install the light bulbs (I) (not included) in accordance with

the fixture’s specifications. (DO NOT EXCEED THE

MAXIMUM WATTAGE RATING!!) (NE PAS DEPASSER

LA PUISSANCE NOMINALE MAXIMALE!)

Your installation is now complete. Return power to the

outlet box and test the fixture.

Note: Illustration (Fig. 1) on this manual is for

installation purposes only. It may or may not be

identical to the fixture purchased.

LA-2898E

Fig.2

FIXTURE

WIRES

Black or

Smooth

HOUSE

WIRES

Black

(Hot)

FIXTURE

WIRES

White or

Ribbed

HOUSE

WIRES

White

(Neutral)

FIXTURE

WIRES

Bare

Copper

(Ground)

HOUSE

WIRES

Green or

Bare

Copper

(Ground)

Set# A-020

- Circular Strap

- Ground Screw

- Mounting Screw*2

CAULKING

BACKPLATE

Candle Cover#CCV20060P-143C

The Great Outdoors 72633-143C User manual

The Great Outdoors 72633-143C User manual

The Great Outdoors 72633-143C User manual

Related papers

Other documents