Quoizel LWS4345A Installation guide

Brand
Quoizel
Model
LWS4345A
Type
Installation guide
A
AA
BB
2019 QuoizelInc.
Model#
LWS4345A
Item# 1221062
1
Package Contents
Español p. 7
Français p. 4
Warnings And Cautions
Tools Required
Helpful tools
Bulb Recommended:
Estimated Assembly Time
Preparation
Quoizel Customer Service
(not included): Flathead screwdriver, Phillips screwdriver, Pliers, Wire
cutters, Electrical tape, Safety goggles, Ladder.
(not included): Wire Stripper
(1) 100W Type-A medium base bulb, Alternate (1) LED bulb.
: 20 - 30 minutes
:
Identify and inspect all parts before beginning installation
Check package contents list and diagrams below to be sure all parts are included.
If any parts are missing or damaged, do not attempt to assemble, install or operate
the fixture.
Contact for replacement parts.
·
·
·
·
·
·
·
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in
doubt.
These instructions are provided for your safety. It is very important you read them completely before installing
fixture. We strongly recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs.
- Make sure bulbs are given sufficient time to cool before removal.
- Do not subject glass parts to any shock while in operation or shattering may result.
Mounting Screw
(Pre-assembled to Crossbar)
PART
DESCRIPTION
QUANTITY
A
Crossbar Assembly
(Pre-assembled to Fixture Body)
1pc
3pcs
2pcs
Wire Connector
Outlet Box Screw
AA
BB
CC
Stock Part#
N/A
914164KIT
6 Corporate Parkway
Goose Creek
SC 29445
Customer Service
Toll Free Phone
E-mail
:
1-844-564-3055
:
[email protected]
For the quickest
response, please visit
and
click on .
Quoizel.com
Contact Us
Thankyou for purchasing a Quoizel product.
Needassistance withparts orassembly?
CallQuoizel CustomerService tollfree at1-844-564-3055;
send us an email at[email protected] orvisit usonline atwww.quoizel.com
B
1pc
CC
B
2pcs
D
E
D
1pc
Shade
E
Socket Collar(Pre-assembled
to Fixture Body)
1pc
Fixture
02.16.2019
C
C
1pc
Ring
N/A
M14172RGEK
2
Outlet Box Screw
Outlet Box
Tab
STEP 2:
A. Loosen the set screw on the coupling of the underside of
the ceiling canopy. Adjust the cord in or out of the ceiling
canopy according to your hanging height.
B. Tighten the set screw on the coupling once your hanging
height is achieved. Move the safety clip next to the hex nut
inside of the ceiling canopy.
Recommended length, from the top of canopy to bottom of
socket, when mounting above a 30 inch high table:
8 foot ceiling 30 inches
9 foot ceiling 42 inches
10 foot ceiling 54 inches
11 foot ceiling 66 inches
12 foot ceiling 78 inches
: The fixture wire should be slightly longer than the
cable. Do not cut the fixture wire. This will be done in step 3.
Note
STEP 3:
a. Confirm the desired hanging height. Refer to step 2 if
adjustments are needed.
b. Using wire cutters, cut the fixture wire leaving
approximately 10 inches of wire extending from the
Canopy. On the fixture wire, remove 4 inches of the
outer sleeve.
c. Using wire strippers, strip each wire ½ inch from the
end.
Ceiling Canopy
STEP 1:
a. Remove the crossbar from the ceiling canopy on the
fixture body.
b. Secure the crossbar to the outlet box (not included) with
outlet box screws.
c. Tighten until snug.
The tab on the crossbar should protrude outward.Note:
Crossbar Assembly
Set Screw
Cord
Cord
Coupling
Safety Clip
Hex Nut
Ceiling
Canopy
Screwdriver
2019 QuoizelInc.
STEP 4:
a. The lanyard is provided as a means to support the
fixture from the junction box while connecting the
electrical wires. This enables the fixture to hang from
the junction box and your hands are free to make the
wire connections.
b. Turn the button stop so it may be inserted into the
crossbar slot. Make sure the button stop is completely
inside the crossbar.
c. Slowly release the fixture to make sure it is supported
by the button stop.
d. Proceed to Step 5. Once wiring is complete, the lanyard
will push into the junction box when the Ceiling Canopy
is Attached to the ceiling.
Crossbar Assembly
Button Stop
Lanyard
Slot
3
CARE AND MAINTENANCE
Wipe clean using soft, dry cloth or static duster. Always avoid using harsh chemicals and abrasives to clean
fixture as they may damage the finish.
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Bulbs will not light.
Fuse blows or the
circuit breaker trips
when light is turned
on.
1. Bulb is burned out.
2. Power is off.
3. Faulty wire connection.
4. Faulty switch.
Crossed wires or power wire is
grounding out.
1 . Replace light bulb.
2. Make sure power supply is on.
3. Check wiring.
4. Test or replace the switch.
Check wire connection.
Your installation is now complete! Restore electricity and save this sheet for future reference.
STEP 8:
a. Install correct bulbs referring to fixture markings and/or labels for maximum wattage.
Mounting Screw
Fixture Body
STEP 7:
a. Remove the socket collar from the socket on the .
b. Position ring so that the curled lip is facing up. Place the
ring on the shade.
c. Place the shade over the socket on the fixture as shown.
d. Hand-tighten until snug.
fixture
Fixture
Shade
Socket Collar
STEP 6:
a. Line up the holes on the canopy of the fixture body and
the mounting holes on the crossbar.
b. Secure with the mounting screws. Tighten until snug.
Ring
Printed in China
2019 QuoizelInc.
WHITE
BLACK (OR RED) WIRE
WHITE OR RIBBED
BLACK OR SMOOTH
FROM SUPPLY
FROM SUPPLY
FROM FIXTURE
FROM FIXTURE
STEP 5:
* Use Wire Connectors (supplied) to connect the wires.
ground wire green ground screw
ground screw
ground wire supply ground
supply white wire white fixture
supply wire
supply black (or red) black
fixture supply wire
a) Ground Wire:
1. Wrap supply around
on mounting bracket, no less than 2 in. from the end of
the wire. Tighten .
2. Connect fixture green to
wire with wire connector.
b) Supply Wire:
1. Connect the to the
with wire connector.
2. Connect the wire to the
with wire connector.
3. Wrap each connection with approved electrical tape and
carefully stuff all of the connected wires into the outlet
box.
GROUND WIRE
GROUND WIRE
FROM SUPPLY
FROM FIXTURE
GREEN GROUND SCREW
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9

Quoizel LWS4345A Installation guide

Brand
Quoizel
Model
LWS4345A
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents