Wacker Neuson G100 User manual

5200007837

01 1012

5200007837

Operator’s Manual

Mobile Generator

G 100

G 120

EN

Copyright notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the

machine. Any other type of reproduction is prohibited without express

written permission from Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker

Neuson Production Americas LLC represents an infringement of valid

copyrights. Violators will be prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their

respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original instructions

This Operator’s Manual presents the original instructions. The original

language of this Operator’s Manual is American English.

G 100 / G 120 Foreword

wc_tx003146gb.fm 3

Foreword

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson Production Americas LLC and must be followed during installation,

operation, and maintenance of the machines.

Machines

covered in

this manual

Machine

documentation

 From this point forward in this documentation, Wacker Neuson Production

Americas LLC will be referred to as Wacker Neuson.

 Keep a copy of the Operator’s Manual with the machine at all times.

 Use the separate Parts Book supplied with the machine to order replacement

parts.

 Refer to the separate Repair Manual for detailed instructions on servicing and

repairing the machine.

 If you are missing any of these documents, please contact Wacker Neuson to

order a replacement or visit www.wackerneuson.com.

 When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Expectations

for

information in

this manual

 This manual provides information and procedures to safely operate and

maintain the above Wacker Neuson model(s). For your own safety and to

reduce the risk of injury, carefully read, understand, and observe all instructions

described in this manual.

 Wacker Neuson expressly reserves the right to make technical modifications,

even without notice, which improve the performance or safety standards of its

machines.

 The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson reserves the right to change

any portion of this information without notice.

CALIFORNIA

Proposition

65 Warning

Engine exhaust, some of its constituents, and certain vehicle components, contain

or emit chemicals known to the State of California to cause cancer and birth

defects or other reproductive harm.

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental

discharge of sparks or flames from the engine exhaust. Spark arresters are

qualified and rated by the United States Forest Service for this purpose. In order to

comply with local laws regarding spark arresters, consult the engine distributor or

the local Health and Safety Administrator.

Machine Item Number

G 100 / G 120 5200003854, 5200003855, 5200003856, 5200003857,

5200003858, 5200003859

Foreword G 100 / G 120

4 wc_tx003146gb.fm

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and

modifications. The following definitions apply:

 Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

 Approved modifications are those performed by an authorized Wacker

Neuson service center according to written instructions published by Wacker

Neuson.

 Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following

consequences:

 Serious injury hazards to the operator and persons in the work area

 Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

Table of Contents

G 100 / G 120

wc_bo5200007837_01TOC.fm

5

Foreword 3

1 Safety Information 9

1.1 Signal Words Used in this Manual ....................................................... 9

1.2 Machine Description and Intended Use ............................................. 10

1.3 Safety Guidelines for Operating the Machine ..................................... 11

1.4 Service Safety .................................................................................... 13

1.5 Operator Safety while Using Internal Combustion Engines ............... 15

1.6 Safety Guidelines for Mobile Generators ........................................... 16

1.7 Safety Guidelines for Towing the Machine ......................................... 18

1.8 Safety Guidelines for Lifting the Machine ........................................... 19

1.9 Reporting Safety Defects ................................................................... 19

2 Labels 20

2.1 Label Locations .................................................................................. 20

2.2 Label Meanings .................................................................................. 22

3 Lifting and Transporting 32

3.1 Lifting the Machine ............................................................................. 32

3.2 Towing the Machine ........................................................................... 33

3.3 Before Towing Checklist ..................................................................... 35

3.4 Hazardous Materials Placards ........................................................... 36

4 Operation 37

4.1 Pre-Start Checklist ............................................................................. 38

4.2 Positioning the Machine ..................................................................... 39

4.3 Recommended Fuel ........................................................................... 40

4.4 Refueling the Machine ........................................................................ 41

4.5 Control Panel ...................................................................................... 42

4.6 Main Line Circuit Breaker ................................................................... 44

4.7 Engine Start Switch ............................................................................ 45

4.8 Idle Switch .......................................................................................... 46

4.9 Pre-Alarm / Shutdown LED ................................................................ 46

4.10 Voltage Selector ................................................................................. 47

4.11 Voltage Selector Label ....................................................................... 48

4.12 Panel Door Interlock Switch ............................................................... 48

4.13 Adjusting Voltage with the Rheostat ................................................... 49

4.14 Emergency Stop Switch ..................................................................... 50

Table of Contents

G 100 / G 120

wc_bo5200007837_01TOC.fm

6

4.15 Grounding the Generator ....................................................................51

4.16 Connection Lugs .................................................................................52

4.17 Convenience Receptacles ..................................................................53

4.18 Before Starting ....................................................................................54

4.19 Manual Start-Up ..................................................................................55

4.20 Operation ............................................................................................57

4.21 Generator Monitoring ..........................................................................58

4.22 Engine Monitoring ...............................................................................59

4.23 Engine Power Correction Factors .......................................................59

4.24 Engine Shutdown Faults .....................................................................60

4.25 Current Overload Fault .......................................................................61

4.26 Event Log ............................................................................................61

4.27 Stopping the Generator ......................................................................61

4.28 Cold Weather Start-Up .......................................................................62

4.29 Block Heater .......................................................................................62

4.30 Remote Run Terminal Block ...............................................................63

4.31 Automatic / Remote Start-Up ..............................................................64

4.32 Remote/Transfer Switch .....................................................................65

4.33 Low Coolant Shutdown .......................................................................66

5 Using the LCD Panel and Keypad 67

5.1 Navigating the Menus .........................................................................68

5.2 Entering Passwords ............................................................................70

5.3 Adjusting Screen Contrast ..................................................................71

5.4 Setting the Time or Date .....................................................................72

5.5 Changing User Preferences ...............................................................73

5.6 Changing / Disabling Low Fuel Fault ..................................................74

5.7 Changing Cooldown Time ..................................................................75

6 Factory Installed Options 76

6.1 Automatic LCD Heat ...........................................................................76

6.2 Temperature-Activated Shutters .........................................................77

6.3 Lockable Battery Disconnect ..............................................................77

6.4 Camlocks ............................................................................................78

6.5 Quick-Disconnect Fuel Fittings ...........................................................79

6.6 Containment System ..........................................................................80

6.7 Battery Charger ..................................................................................80

Table of Contents

G 100 / G 120

wc_bo5200007837_01TOC.fm

7

7 Maintenance 81

7.1 Preparing for Maintenance ................................................................. 81

7.2 Periodic Maintenance Schedule ......................................................... 82

7.3 Cleaning the Machine ......................................................................... 83

7.4 Inspecting the Machine ...................................................................... 84

7.5 Checking the Engine Oil Level ........................................................... 85

7.6 Checking the Engine Coolant Level ................................................... 86

7.7 Checking the Air Cleaning System ..................................................... 87

7.8 Maintaining the Air Cleaner ................................................................ 88

7.9 Checking the Exhaust System ........................................................... 90

7.10 Checking and Draining the Containment System (if equipped) .......... 91

7.11 Draining the Fuel / Water Separator ................................................... 92

7.12 Maintaining the Batteries .................................................................... 93

7.13 Changing the Engine Oil and Oil Filter ............................................... 94

7.14 Replacing the Fuel Filter .................................................................... 96

7.15 Checking Fan Belt Tension ................................................................ 98

7.16 Performing Coolant Solution Analysis ................................................ 99

7.17 Testing the Cooling System Pressure .............................................. 100

7.18 Maintaining the Trailer ...................................................................... 102

7.19 Resetting the Periodic Maintenance Timer ...................................... 103

7.20 Storage ............................................................................................. 104

7.21 Machine Disposal / Decommissioning .............................................. 105

8 Troubleshooting 106

9 Technical Data 107

9.1 Engine .............................................................................................. 107

9.2 Generator ......................................................................................... 108

9.3 Trailer and Skid ................................................................................ 109

9.4 Dimensions ....................................................................................... 110

Tire Safety Information 111

10 User’s Information for Transport Canada Fuel Tank 123

Table of Contents

G 100 / G 120

wc_bo5200007837_01TOC.fm

8

11 Emission Control Systems Information and Warranty 127

11.1 Emission Control System Background Information ..........................127

11.2 Limited Defect Warranty for Exhaust Emission Control System .......128

11.3

Limited Defect Warranty for Wacker Neuson Emission Control Systems

.128

12 Schematics 132

12.1 Engine Wiring ...................................................................................132

12.2 Engine Wiring Components ..............................................................133

12.3 Electrical Schematic .........................................................................134

12.4 Electrical Schematic Components ....................................................135

wc_si000717gb.fm

9

G 100 / G 120 Safety Information

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE

signal words which must be followed to reduce the possibility of personal injury,

damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a situation

which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

f Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

f To avoid death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

f To avoid possible death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

f To avoid possible minor or moderate injury from this type of hazard, obey all

safety messages that follow this signal word.

wc_si000717gb.fm

10

Safety Information G 100 / G 120

1.2 Machine Description and Intended Use

This machine is a mobile electric power source. The Wacker Neuson Mobile

Generator consists of a trailer-mounted cabinet containing an electric alternator, a

fuel tank, and a diesel engine. A control panel, receptacles, and connection lugs

are provided on the side of the cabinet. As the engine runs, the generator converts

mechanical energy into electric power. The operator connects loads to the electric

power receptacles and connection lugs.

This machine is intended for the purpose of supplying electrical power to

connected loads. Refer to the product specifications for the output voltage and

frequency of this generator, and for the maximum output power limit of this

generator.

This machine has been designed and built strictly for the intended use described

above. Using the machine for any other purpose could permanently damage the

machine or seriously injure the operator or other persons in the area. Machine

damage caused by misuse is not covered under warranty.

The following are some examples of misuse:

 Connecting a load that has voltage and frequency requirements that are

incompatible with the generator output

 Overloading the generator with a load that draws excessive power during either

continuous running or start-up

 Operating the generator in a manner that is inconsistent with all federal, state

and local codes and regulations

 Using the machine as a ladder, support, or work surface

 Using the machine to carry or transport passengers or equipment

 Using the machine to tow other machines

 Operating the machine outside of factory specifications

 Operating machine in a manner inconsistent with all warnings found on the

machine and in the Operator’s Manual

This machine has been designed and built in accordance with the latest global

safety standards. It has been carefully engineered to eliminate hazards as far as

practicable and to increase operator safety through protective guards and labeling.

However, some risks may remain even after protective measures have been taken.

They are called residual risks. On this machine, they may include exposure to:

 Heat, noise, exhaust, and carbon monoxide from the engine

 Fire hazards from improper refueling techniques

 Fuel and its fumes

 Electric shock and arc flash

 Personal injury from improper lifting the trailer tongue

 Typical hazards related to towing a trailer on roads and highways

To protect yourself and others, make sure you thoroughly read and understand the

safety information presented in this manual before operating the machine.

wc_si000717gb.fm

11

G 100 / G 120 Safety Information

1.3 Safety Guidelines for Operating the Machine

Operator

training

Before operating the machine:

 Read and understand the operating instructions contained in all manuals

delivered with the machine.

 Familiarize yourself with the location and proper use of all controls and safety

devices.

 Contact Wacker Neuson for additional training if necessary.

When operating this machine:

 Do not allow improperly trained people to operate the machine. People

operating the machine must be familiar with the potential risks and hazards

associated with it.

Operator

qualifications

Only trained personnel are permitted to start, operate, and shut down the machine.

They also must meet the following qualifications:

 have received instruction on how to properly use the machine

 are familiar with required safety devices

The machine must not be accessed or operated by:

 children

 people impaired by alcohol or drugs

Application

area

Be aware of the application area.

 Keep unauthorized personnel, children, and pets away from the machine.

 Remain aware of changing positions and the movement of other equipment and

personnel in the application area/job site.

Be aware of the application area.

 Do not operate the machine in areas that contain flammable objects, fuels, or

products that produce flammable vapors.

Safety

devices,

controls, and

attachments

Only operate the machine when:

 All safety devices and guards are in place and in working order.

 All controls operate correctly.

 The machine is set up correctly according to the instructions in the Operator’s

Manual.

 The machine is clean.

 The machine’s labels are legible.

To ensure safe operation of the machine:

 Do not operate the machine if any safety devices or guards are missing or

inoperative.

 Do not modify or defeat the safety devices.

 Only use accessories or attachments that are approved by Wacker Neuson.

wc_si000717gb.fm

12

Safety Information G 100 / G 120

Safe

operating

practices

When operating this machine:

 Remain aware of the machine’s moving parts. Keep hands, feet, and loose

clothing away from the machine’s moving parts.

When operating this machine:

 Do not operate a machine in need of repair.

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while operating this

machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

After Use

 Stop the engine when the machine is not being operated.

 Close the fuel valve on engines equipped with one when machine is not being

operated.

 Ensure that the machine will not tip over, roll, slide, or fall when not being

operated.

 Store the machine properly when it is not being used. The machine should be

stored in a clean, dry location out of the reach of children.

wc_si000717gb.fm

13

G 100 / G 120 Safety Information

1.4 Service Safety

Service

training

Before servicing or maintaining the machine:

 Read and understand the instructions contained in all manuals delivered with

the machine.

 Familiarize yourself with the location and proper use of all controls and safety

devices.

 Only trained personnel shall troubleshoot or repair problems occurring with the

machine.

 Contact Wacker Neuson for additional training if necessary.

When servicing or maintaining this machine:

 Do not allow improperly trained people to service or maintain the machine.

Personnel servicing or maintaining the machine must be familiar with the

associated potential risks and hazards.

Precautions

Follow the precautions below when servicing or maintaining the machine.

 Read and understand the service procedures before performing any service to

the machine.

 All adjustments and repairs must be completed before operating the machine.

Do not operate the machine with a known problem or deficiency.

 All repairs and adjustments shall be completed by a qualified technician.

 Turn off the machine before performing maintenance or making repairs.

 Remain aware of the machine’s moving parts. Keep hands, feet, and loose

clothing away from the machine’s moving parts.

 Reinstall the safety devices and guards after repair and maintenance

procedures are complete.

Machine

modifications

When servicing or maintaining the machine:

 Use only accessories/attachments that are approved by Wacker Neuson.

When servicing or maintaining the machine:

 Do not defeat safety devices.

 Do not modify the machine without the express written approval of Wacker

Neuson.

Replacing

parts and

labels

 Replace worn or damaged components.

 Replace all missing and hard-to-read labels.

 When replacing electrical components, use components that are identical in

rating and performance to the original components.

 When replacement parts are required for this machine, use only Wacker

Neuson replacement parts or those parts equivalent to the original in all types of

specifications, such as physical dimensions, type, strength, and material.

wc_si000717gb.fm

14

Safety Information G 100 / G 120

Cleaning

When cleaning and servicing the machine:

 Keep the machine clean and free of debris such as leaves, paper, cartons, etc.

 Keep the labels legible.

When cleaning the machine:

 Do not clean the machine while it is running.

 Never use gasoline or other types of fuels or flammable solvents to clean the

machine. Fumes from fuels and solvents can become explosive.

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while servicing or

maintaining this machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

In addition, before servicing or maintaining the machine:

 Tie back long hair.

 Remove all jewelry (including rings).

Electrical

service safety

 Make sure clothing and shoes are dry, stand on a dry wooden platform or rubber

insulating mat, and use tools with insulated handles when servicing the

machine.

 Do not allow water to accumulate around the base of the machine. If water is

present, move the machine and allow the machine to dry before servicing.

 Do not pressure wash the control panel, generator end, or any other electrical

components when cleaning the machine.

Cooling

system safety

 Do not attempt to open the radiator cap while the unit is running or before the

engine has cooled down. Severe burns may result!

 Engine coolant is toxic to humans and animals. Clean up spills and dispose of

waste engine coolant in accordance with local environmental regulations.

wc_si000717gb.fm

15

G 100 / G 120 Safety Information

1.5 Operator Safety while Using Internal Combustion Engines

Operating

safety

When running the engine:

 Keep the area around exhaust pipe free of flammable materials.

 Check the fuel lines and the fuel tank for leaks and cracks before starting the

engine. Do not run the machine if fuel leaks are present or the fuel lines are

loose.

When running the engine:

 Do not smoke while operating the machine.

 Do not run the engine near sparks or open flames.

 Do not touch the engine or muffler while the engine is running or immediately

after it has been turned off.

 Do not operate a machine when its fuel cap is loose or missing.

 Do not start the engine if fuel has spilled or a fuel odor is present. Move the

machine away from the spill and wipe the machine dry before starting.

Refueling

safety

When refueling the engine:

 Clean up any spilled fuel immediately.

 Refill the fuel tank in a well-ventilated area.

 Replace the fuel tank cap after refueling.

 Do not smoke.

 Do not refuel a hot or running engine.

 Do not refuel the engine near sparks or open flames.

 Use suitable tools for refueling (for example, a fuel hose or funnel).

WARNING

Internal combustion engines present special hazards during operation and fueling.

Failure to follow the warnings and safety standards could result in severe injury or

death.

f Read and follow the warning instructions in the engine owner’s manual and the

safety guidelines below.

DANGER

Exhaust gas from the engine contains carbon monoxide, a deadly poison.

Exposure to carbon monoxide can kill you in minutes.

f NEVER operate the machine inside an enclosed area, such as a tunnel, unless

adequate ventilation is provided through such items as exhaust fans or hoses.

wc_si000717gb.fm

16

Safety Information G 100 / G 120

1.6 Safety Guidelines for Mobile Generators

Installing as

backup power

Special hazards exist when installing this machine as a backup power supply.

Improper connection of generator to a building’s electrical system can allow

electrical current from the generator to backfeed into utility lines. This may result in

electrocution of utility workers, fire, or explosion.

If connected to a building’s electrical system, the generator must meet the power,

voltage, and frequency requirements of the equipment in the building. Differences

in power, voltage, and frequency requirements may exist and improper connection

may lead to equipment damage, fire, and personal injury or death.

DANGER

Carbon monoxide. Using a generator indoors CAN KILL YOU IN MINUTES.

Generator exhaust contains carbon monoxide (CO). This is a poison you cannot

see or smell. If you can smell the generator exhaust, you are breathing CO. But

even if you cannot smell the exhaust, you could be breathing CO.

f NEVER use a generator inside homes, garages, crawlspaces, or other partly

enclosed areas. Deadly levels of carbon monoxide can build up in these areas.

Using a fan or opening windows and doors does NOT supply enough fresh air.

f ONLY use a generator outside and far away from windows, doors, and vents.

These openings can pull in generator exhaust.

f Even when you use a generator correctly, CO may leak into the home. ALWAYS

use a battery-powered or battery-backup CO alarm in the home.

f If you start to feel sick, dizzy, or weak after the generator has been running,

move to fresh air RIGHT AWAY. See a doctor. You could have carbon monoxide

poison.

WARNING

Electrocution hazard. Machines that generate electric power present special

hazards while the engine is running. These include the risk of electrocution or

severe electrical shock.

f Read and follow the instructions in this Operator’s Manual.

WARNING

Backfeed from the generator into the public power distribution system can cause

serious injury or death to utility workers!

f Connections to a building’s electrical system must be made by a qualified elec-

trician and comply with all applicable laws and electrical codes.

wc_si000717gb.fm

17

G 100 / G 120 Safety Information

General safety

 Do not use evaporative starting fluids to start the engine. They are highly

explosive.

 Do not store items such as excess oil, rags, or tools on top of or inside the

machine. These items are a fire hazard and can restrict cooling air.

 Ensure that electrical cords attached to the machine are in serviceable condition

without cuts, cracks, or exposed wires.

 Do not route electrical cords over vibrating or hot parts of the machine.

 Do not stand on the machine.

 Do not enclose or cover the machine when it is use, or when it is hot.

Ground

Connection

The generator must be connected to a good earthen ground for proper operating

safety.

A central “equipment ground” is provided at the customer connection lugs. This

point is connected directly to the generator set base. All other system grounds are

connected to this central point. Ground the generator in accordance with the

standards defined in national, state, and local regulations.

After Use

 Stop the engine when the machine is not being operated.

 Ensure that the machine will not tip over, roll, slide, or fall when not being

operated.

 Store the machine properly when it is not being used. The machine should be

stored in a clean, dry location out of the reach of children.

wc_si000717gb.fm

18

Safety Information G 100 / G 120

1.7 Safety Guidelines for Towing the Machine

When towing the machine:

 Do not tow the machine if the towing vehicle’s hitch or the trailer’s coupler are

damaged.

 Do not tow the machine if any of the trailer’s lug nuts are missing.

 Do not tow the machine if the trailer’s tires have less than 1.5 mm (1/16 inch) of

tread.

 Do not tow the machine unless the trailer’s brakes are functioning properly.

 Do not exceed the trailer manufacturer’s speed limitations.

When towing the machine:

 Only tow the machine when the trailer’s lug nuts are properly torqued.

 Only tow the machine when the trailer’s tires are properly inflated.

 Only tow the machine when all trailer lights are functioning correctly.

 Only tow the machine when the trailer’s safety chains are connected to the

towing vehicle in a crisscross pattern.

 Maintain extra distance between the towing vehicle and other vehicles.

 Avoid soft shoulders, curbs, and sudden lane changes

 Abide by all licensing requirements for your area.

If you have not driven a towing vehicle with trailer before, practice turning,

stopping, and backing up the towing vehicle with trailer in an area away from traffic.

Only drive the towing vehicle with trailer when you are confident in your ability to do

so.

WARNING

Risk of severe injury or death. Improper trailer condition and towing technique can

lead to an accident.

f Obey the trailer manufacturer’s instructions and the instructions below to reduce

the risk of an accident.

wc_si000717gb.fm

19

G 100 / G 120 Safety Information

1.8 Safety Guidelines for Lifting the Machine

When lifting the machine:

 Make sure slings, chains, hooks, ramps, jacks, forklifts, cranes, hoists, and any

other type of lifting device used is attached securely and has enough weight-

bearing capacity to lift or hold the machine safely. See section Technical Data

for machine weight.

 Remain aware of the location of other people when lifting the machine.

 Only use the lifting points and tie-downs described in the Operator’s Manual.

 Make sure the transporting vehicle has sufficient load capacity and platform size

to safely transport the machine.

To reduce the possibility of injury:

 Do not stand under the machine while it is being lifted or moved.

 Do not get onto the machine while it is being lifted or moved.

1.9 Reporting Safety Defects

If you believe your trailer has a defect which could cause a crash or could cause

injury or death, you should immediately inform the National Highway Traffic Safety

Administration (NHTSA) in addition to notifying Wacker Neuson.

If NHTSA receives similar complaints, it may open an investigation; and if it finds

that a safety defect exists in a group of trailers, it may order a recall and remedy

campaign. However, NHTSA cannot become involved in individual problems

between you, your dealer, or Wacker Neuson.

To contact NHTSA, you may either contact the Vehicle Safety Hotline toll-free at

1-888-327-4236 (TTY: 1-800-424-9153), go to http://www.safercar.gov; or write to:

Administrator

NHTSA

1200 New Jersey Avenue S.E.

Washington, DC 20590

You can also obtain other information about your motor vehicle safety from

http://www.safercar.gov

Labels G 100 / G 120

20 wc_si000718gb.fm

2 Labels

2.1 Label Locations

WARNING

AVERTISSEMENT

ADVERTENCIA

WARNING

WARNUNG

DIESEL

STOP

DANGER

PELIGRO

GEFAHR

DANGER

177416

ULTRA LOW SULFUR FUEL ONLY.

NUR ULTRANIEDRIGEN SCHWEFELKRAFTSTOFF.

SOLAMENTE COMBUSTIBLE DE ULTRABAJO CONTENIDO DE AZUFRE.

SEULEMENT CARBURANT DE SOUFRE ULTRA BAS.

WARNING

AVERTISSEMENT

ADVERTENCIA

WARNUNG

179282

ACHTUNG

AVISO

ATTENTION

NOTICE

wc_gr009501

Metering

Engine

Main

A

FF

HH

S

F

ZZ

U

EE

GG

CC

AA

WW

QQ

BB

H

I

YY

X

W

L

R

DD

RR

N

M

SS

V

Q

Y

P

C

PP

A

Page is loading ...

Wacker Neuson G100 User manual

This manual is also suitable for

Wacker Neuson G100 User manual

Related papers

Other documents