Contec PCE37/9PS Owner's manual

Contec
Brand
Contec
Model
PCE37/9PS
Type
Owner's manual

Contec PCE37/9PS is a connection conversion cable for Serial I/O. It converts the CN1 (37-pin D-SUB connector) on the board of Serial I/O to 9-pin D-SUB male connectors for four channels. This allows you to connect four RS-232C or RS-422A/485 devices to your computer. The cable is 250mm long and weighs 200g. It has a 37-pin D-SUB male connector on one end and four 9-pin D-SUB male connectors on the other end. The cable is shielded to protect against electromagnetic interference.

Here are some of the possible use cases for the Contec PCE37/9PS:

  • Connecting four serial devices to a single computer

Contec PCE37/9PS is a connection conversion cable for Serial I/O. It converts the CN1 (37-pin D-SUB connector) on the board of Serial I/O to 9-pin D-SUB male connectors for four channels. This allows you to connect four RS-232C or RS-422A/485 devices to your computer. The cable is 250mm long and weighs 200g. It has a 37-pin D-SUB male connector on one end and four 9-pin D-SUB male connectors on the other end. The cable is shielded to protect against electromagnetic interference.

Here are some of the possible use cases for the Contec PCE37/9PS:

  • Connecting four serial devices to a single computer
1 PCE37/9PS
Connection Conversion Cable
for Serial I/O (37P→9Px4)
PCE37/9PS User’s Guide
CONTEC CO.,LTD.
This cable converts the CN1 (37-pin D-SUB connector) on the board of Serial I/O to 9-pin
D-SUB male connectors for four channels as shown below.
Suitable boards : COM-4(PCI)H, COM-4(PCI), COM-4P(PCI)H, COM-4PD(PCI)H, COM-4M(PC)
External Dimensions
CH1
CH2
CH3
CH4
250mm
5
1
6
33.1mm
9
15.0mm
16.4mm
72.2mm
1
37
19
20
Specifications
Item Specification
Connector
37-pin
D-SUB
male connector
Thumb screw
:
UNC#4-40(
Inch screw
)
9-pin
D-SUB
male connector
Screw nut:
UNC#4-40(
Inch screw
)
Cable 9 core shield cable
Conductor size
: AWG28
Conductor composition
: 7pcs/0.127mm UL2919
Weight
200g
Notes!
- Do not strike or bend the product. Otherwise, the product may malfunction, overheat, cause a
failure or breakage.
- Do not insert or remove the connector while the power is turned on to the PC. Failure to observe
this precaution may cause malfunction, overheating.
- The specifications of this product are subject to change without notice for quality improvement.
Even when using the product continuously, be sure to read the manual and understand the contents.
- Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that may
appear in this document or for any results of using the product.
- All relevant issues have been considered in the preparation of this document. Should you notice an
omission or any questionable item in this document, please feel free to notify CONTEC CO., LTD.
PCE37/9PS User’s Guide
Copyright 1997 CONTEC CO., LTD. ALL RIGHTS RESERVED.
CONTEC CO., LTD. August 2006 Edition
3-9-31, Himesato, Nishiyodogawa-ku, Osaka 555-0025, Japan
Japanese http://www.contec.co.jp/
English http://www.contec.com/ A-41-727 (LZB9961)
Chinese http://www.contec.com.cn/ 08032006_rev5 [03141997]
No part of this document may be copied or reproduced in any form by any means without prior written
consent of CONTEC CO., LTD.
Connection Diagram
CH1
CH2
CH3
CH4
TxD-
TxD+
RTS-
RTS+
SG
9
8
7
6
RxD-
RxD+
CTS+
CTS-
5
4
3
2
1
SG
DTR
TxD
RxD
DCD
9
8
7
6
RI
CTS
RTS
DSR
5
4
3
2
1
Pin No. on
the 9-pin D-SUB
connectors
Pin No. on
the 9-pin D-SUB
connectors
CH1 - 3
CH1 - 7
CH1 - 6
CH1 - 4
CH1 - 9
CH2 - 2
CH2 - 8
CH2 - 5
CH2 - 1
CH4 - 3
CH4 - 7
CH4 - 6
CH4 - 4
CH4 - 9
CH3 - 2
CH3 - 8
CH3 - 5
CH3 - 1
N.C.
CH1 - 2
CH1 - 8
CH1 - 5
CH1 - 1
CH2 - 3
CH2 - 7
CH2 - 6
CH2 - 4
CH2 - 9
CH4 - 2
CH4 - 8
CH4 - 5
CH4 - 1
CH3 - 3
CH3 - 7
CH3 - 6
CH3 - 4
CH3 - 9
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
Pin Assignments for RS-232C
Pin Assignments for RS-422A/485
CH1 - CH4
CH1 - CH4
  • Page 1 1
  • Page 2 2

Contec PCE37/9PS Owner's manual

Contec
Brand
Contec
Model
PCE37/9PS
Type
Owner's manual

Contec PCE37/9PS is a connection conversion cable for Serial I/O. It converts the CN1 (37-pin D-SUB connector) on the board of Serial I/O to 9-pin D-SUB male connectors for four channels. This allows you to connect four RS-232C or RS-422A/485 devices to your computer. The cable is 250mm long and weighs 200g. It has a 37-pin D-SUB male connector on one end and four 9-pin D-SUB male connectors on the other end. The cable is shielded to protect against electromagnetic interference.

Here are some of the possible use cases for the Contec PCE37/9PS:

  • Connecting four serial devices to a single computer
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents