Medtronic Breeze SleepGear CPAP Interface User guide

Page is loading ...

Breeze SleepGear iii

Contents

Overview ...................................................................................... 1

Components .................................................................. 1

Nasal Pillows .................................................... 2

DreamSeal ........................................................ 2

Indications for Use ......................................................... 3

Technical Data ...............................................................3

Assembly ..................................................................................... 4

Use ............................................................................................... 5

Inspection ...................................................................... 5

Fitting ............................................................................. 5

Adjustment ..................................................................... 6

Cleaning ....................................................................................... 8

This manual is available online at: http://www.puritanbennett.com

Nellcor Puritan Bennett Inc. is an affiliate of Tyco Healthcare. Breeze,

SleepGear, and DreamSeal are trademarks of Nellcor Puritan Bennett Inc.

Contents

iv Breeze SleepGear

Warnings

Warnings are identified by the WARNING symbol shown above and alert the user to

potential serious outcomes (death, injury, or adverse events) to the patient or user.

WARNINGS:

• Do not block or modify the vent hole(s).

• To ensure sufficient air for respiration, do not wear the Breeze SleepGear

until it is connected to a properly operating CPAP machine.

• At low CPAP pressures, flow through the vent hole(s) may be inadequate

to clear all exhaled gas from the Breeze SleepGear. Some rebreathing and

inhalation of carbon dioxide may occur.

• If you experience skin irritation, soreness or discoloration, eye

discomfort, gastric problems such as distention or bloating, nasal

irritation or dryness, excessive hair loss, or any discomfort from using

the Breeze SleepGear, discontinue use and consult your physician.

• If oxygen is used with the Breeze SleepGear or CPAP machine, turn

oxygen flow off whenever the CPAP machine is off.

Cautions

Cautions are identified by the CAUTION symbol shown above and alert the user to

exercise care necessary for the safe and effective use of the Breeze SleepGear.

Caution: By US Federal law, this device may be sold or used only as

ordered by a licensed physician.

Notes

Notes are identified by the NOTE symbol shown above and provide additional helpful

information.

English

Breeze SleepGear 1

Overview

The Puritan-Bennett Breeze SleepGear (Single Patient Use) is

offered in two airway assembly configurations:

• Nasal Pillows

• DreamSeal

User information for both configurations is presented in this guide.

Components

The primary components that comprise the Breeze SleepGear are:

• Nasal Pillows (or DreamSeal)

• Shell

• Vent Hole Insert (DreamSeal only)

• Vent Hole(s)

• Wing Knob

• Pivot (DreamSeal only)

•Hose

•Hose Guide

• Clip (Nasal Pillows only)

• Outrigger

• Spine Adapter

• Swivel Adapter

•Cradle

•Halo Straps

Refer to the figures on the following page.

English

Overview

2 Breeze SleepGear

Nasal Pillows

DreamSeal

English

1. Nasal Pillows

2. Vent holes

3. Shell

4. Wing knob

5. Clip

6. Hose

7. Hose guide

8. Outrigger

9. Swivel adapter

10.Spine adapter

11. Cradle

12.Halo straps

1. DreamSeal

2. Shell

3. Vent hole insert

4. Pivot

5. Hose

6. Hose guide

7. Outrigger

8. Swivel adapter

9. Spine

10.Cradle

11. Halo straps

Overview

Breeze SleepGear 3

Indications for Use

This product is intended for use with devices that deliver continuous

positive airway pressure (CPAP) and bi-level positive airway

pressure in patients weighing at least 30 kg. Refer to the warnings

on page iv.

Technical Data

The following table provides the technical data for both the

Nasal Pillows and DreamSeal configurations.

English

Vent Flow, Pressure Range, and Materials

Parameter

CPAP Pressure

(cmH

2

O)

Flow Rate

(L/min)

Pressure Range 3 – 30 with DreamSeal with Nasal Pillows

Vent Flow

31317

51620

82125

10 23 28

12 25 31

15 28 35

18 31 39

20 32 41

25 34 47

30 38 53

Storage and

Operating Conditions

— Storage Operating

Temp. Range -40°F to 158°F

(-40°C to 70°C)

41°F to 104°F

(5°C to 40°C)

Relative Humidity

(noncondensing)

Up to 95% Up to 95%

Materials

• Nasal Pillows: medical-grade silicone

• DreamSeal Perimeter Seal: medical-grade silicone

• Halo Straps: Velstretch

®

Assembly

4 Breeze SleepGear

Assembly

Before using the Breeze SleepGear for the first time, assemble it as

follows:

1. Insert the nasal airway assembly (item 1) into the SleepGear

assembly spine adapter (item 2). The hose guide slides back and

forth in the spine adapter with a ratcheting sound.

2. Nasal Pillows airway configuration: While pinching the Nasal

Pillows between the thumb and forefinger, insert the Nasal Pillows

into the shell holes with a gentle rotating motion.

3. DreamSeal airway configuration: Perform the following steps and

refer to the figure on the next page.

• Attach the DreamSeal to the shell by inserting the lip on the

bottom of the DreamSeal into the notch on the bottom of the

shell.

• Place your thumb and forefinger on the two raised circles on the

DreamSeal.

• Rotate the DreamSeal toward the shell and squeeze gently to

engage the two side latches.

English

a

Use

Breeze SleepGear 5

4. Optional: Thread the halo straps through the slots in the cradle

(see figure below, item 1). Then thread the halo straps through the

outrigger (item 2) or through the optional clip accessory (item 3 –

Nasal Pillows only). Engage the Velcro

®

fasteners on the straps.

Note: You may wish to try fitting the Breeze SleepGear

without the halo straps first, then add the straps if a

better fit is required. Refer to the Adjustment section

on the following page.

Use

Inspection

Inspect the Breeze SleepGear and its components before each use

to ensure all parts are firmly connected and no visible leaks exist.

Fitting

1. Insert the Nasal Pillows into your nostrils or place the DreamSeal

over your nose.

English

Nasal Pillows - Side View

Use

6 Breeze SleepGear

Caution: Avoid excessive bending of the nasal airway

assembly when putting on the Breeze SleepGear.

2. Place the cradle (back pad) below the curve at the back of

your head.

Adjustment

1. Adjust the position of the cradle on the spine so that the cradle sits

comfortably at the base of your head.

2. Place your hand on the spine and hold it firmly to the back of your

head. Adjust the length of the Breeze SleepGear with your free

hand by moving the nasal airway assembly toward your face.

Refer to the following figure.

3. Adjust the height and angle of the shell so that the Nasal Pillows or

DreamSeal device is comfortable and there are no audible leaks.

4. Optional: Use the halo straps, if needed, to add stability and

enhance the fit of the Breeze SleepGear.

English

Use

Breeze SleepGear 7

• Adjust the tension of the halo straps for a comfortable fit. Do not

overtighten the straps.

• If using the optional clip accessory, adjust by first lifting the clip;

then, slide the clip to one of the three available positions along

the hose guide that provides the most comfortable fit.

5. Pressurize the interface with your positive airway pressure device

and readjust as required to eliminate leaks.

Notes:

• The amount of force on your nose should be just enough to

prevent air leaks.

• You may need to readjust the fit of Breeze SleepGear when you

lie down.

• The use of humidification may improve comfort during use.

English

Closeup of Clip AdjustmentUsing Halo Straps With Clip

Cleaning

8 Breeze SleepGear

Cleaning

Note: To prolong the life of the product, it is recommended that

the Breeze SleepGear be cleaned thoroughly at least

once per week.

Caution: Hand clean only. To avoid damage to the Breeze

SleepGear, never use a dishwasher or other

mechanical device to clean the Breeze SleepGear

or any of its components.

1. Disconnect the back half of the nasal airway assembly (item 1)

where the hose guide attaches to the spine adapter (item 2).

2. Remove the Nasal Pillows or the DreamSeal from the shell.

To remove the Nasal Pillows, pinch the Nasal Pillows between

your thumb and forefinger; then, pull the Nasal Pillows out of the

shell holes with a gentle rotating motion.

To remove the DreamSeal from the shell, do the following and

refer to the next figure.

• Place your thumb and forefinger on the two raised circles on the

DreamSeal.

English

Cleaning

Breeze SleepGear 9

• Squeeze gently to disengage the two side latches.

• Rotate the DreamSeal away from the shell.

• Disengage the lip on the bottom of the DreamSeal from the

notch on the bottom of the shell.

Caution: To avoid damaging the hoses when connecting or

disconnecting them, use the methods described in

the following instructions. Never pull on or twist the

ribbed portions of hoses. Refer to the figure below.

3. Disconnect the hose at the swivel adapter:

• Grasp each hose at its rubber cuff.

• Gently pull hoses apart.

4. Remove the vent hole insert from the DreamSeal shell. Slide your

fingernail under the end of the insert with the raised indicator

dot(s) and pull the insert up and out.

English

Cleaning

10 Breeze SleepGear

Caution: Do not immerse components with foam pads

attached. Do not sterilize. Do not use bleach-,

chlorine-, or aromatic-based solutions, scented oils,

or moisturizing, antibacterial, deodorizing, or

fragranced soaps to clean the nasal pillows, mask,

headgear, padding, or air tubing. Use of such

substances may cause hardening of your Breeze

SleepGear, thereby reducing the life of the product.

Caution: Do not expose the mask or tubing to direct sunlight.

Exposure to direct sunlight may cause deterioration

of the product.

5. Wash the nasal airway assembly parts in warm, soapy water as

necessary to remove dirt, body oils, cosmetics, etc. Rinse them

thoroughly in clean running water and air dry on a clean,

absorbent surface. Foam pads may be wiped with a mild soap

applied to a moist cloth.

6. To install the vent hole insert, align the indicator dot on the insert

with the dot on the shell. Press the vent hole insert into the

opening in the shell. Make sure the inner lip on the vent hole

insert is fully inserted into the shell.

7. If you are using the halo straps, release the ends and pull the

straps through the outrigger and cradle slots. The cradle may be

separated from the spine adapter for cleaning.

8. Extend the cradle (item 1) to its maximum adjustment and then

pull on the cradle more forcefully to separate it from the spine

adapter (item 2).

English

Page is loading ...

Breeze SleepGear 47

Contenido

Generalidades ........................................................................... 49

Componentes .............................................................. 49

Almohadillas nasales ...................................... 50

DreamSeal ...................................................... 50

Indicaciones de uso ..................................................... 50

Información técnica ..................................................... 51

Montaje ...................................................................................... 52

Uso ............................................................................................. 53

Inspección ................................................................... 53

Prueba de medida ....................................................... 53

Ajuste ........................................................................... 54

Limpieza .................................................................................... 56

Este manual está disponible en línea en: http://www.puritanbennett.com

Nellcor Puritan Bennett Inc. es una filial de Tyco Healthcare. Breeze,

SleepGear

y

DreamSeal

son marcas registradas de Nellcor Puritan Bennett Inc.

Page is loading ...

Puritan Bennett Corporation

4280 Hacienda Drive

Pleasanton, CA 94588 U.S.A.

Telephone Toll Free 1.800.255.6774

Authorized Representative

Tyco Healthcare UK LTD

154 Fareham Road

Gosport PO13 0AS, U.K.

Rx ONLY

Assembled in Mexico

10018938

A-0507

Medtronic Breeze SleepGear CPAP Interface User guide

This manual is also suitable for

Medtronic Breeze SleepGear CPAP Interface User guide

in other languages

Related papers

Other documents