LXE HX2A3116 User manual

HX2 Multi-Charger User’s Guide

Models HX2A310CHGR6US and HX2A311CHGR6WW

For Use with LXE HX2 Lithium Ion Battery Packs

E-EQ-HX2CHGROG-B

Notices

LXE Inc. reserves the right to make improvements or changes in the products described in this manual at any time

without notice. While reasonable efforts have been made in the preparation of this document to assure its accuracy,

LXE assumes no liability resulting from any errors or omissions in this document, or from the use of the information

contained herein. Further, LXE Incorporated, reserves the right to revise this publication and to make changes to it

from time to time without any obligation to notify any person or organization of such revision or changes.

Copyright Notice:

This manual is copyrighted. All rights are reserved. This document may not, in whole or in part, be copied,

photocopied, reproduced, translated or reduced to any electronic medium or machine-readable form without prior

consent, in writing, from LXE Inc. Further, LXE Incorporated, reserves the right to revise this publication and to

make changes to it from time to time without any obligation to notify any person or organization of such revision or

changes.

125 Technology Parkway, Norcross, GA 30092, U.S.A. (770) 447-4224

LXE® and Spire® are registered trademarks of LXE Inc. All other brand or product names are trademarks or

registered trademarks of their respective companies or organizations. When this user guide is in PDF format:

logo, Acrobat, and the Acrobat logo are trademarks of Adobe Systems Incorporated." applies.

IMPORTANT SAFETY WARNINGS US

SAVE THESE INSTRUCTIONS

This document contains important safety and operating instructions for the LXE HX2 Multi-Charger. Please read all

instructions and cautionary markings on the charger/analyzer itself before putting the unit into service.

Safety Alert Symbols

This symbol is used to call your attention to instructions concerning your personal safety. Watch for

this symbol – it will alert you to important safety precautions that must be observed to avoid death,

personal injury or property damage. Follow the instructions after the warning symbol and be alert to

the possibility of personal injury or death.

These signal words provide users with information about the seriousness of the hazard involved:

DANGER WARNING CAUTION

Indicates imminent hazards

which, if not avoided, WILL

result in severe personal injury

or death.

Indicates potential hazards

which, if not avoided, COULD

result in severe personal injury

or death.

Indicates hazards or unsafe practices which,

if not avoided, COULD result in minor or

moderate personal injury or property

damage.

Safety Instructions

Setting up the HX2 Multi-Charger

Locate or orient the AC cord so that it will not be stepped on, tripped over or subjected to damage or stress.

CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

Analyze or charge only LXE HX2A301BATTSTD / HX2A302BATTEXT Rechargeable Lithium Ion Battery Packs in

this charger/analyzer. Other batteries or battery packs may burst causing injury or property damage.

Operating the HX2 Multi-Charger

Only users who have read and understand all operating instructions are qualified to operate the HX2 Multi-Charger.

Failure to read, understand and follow safety instructions may result in injury or death.

Keep the charger/analyzer away from any heat source. Excessive internal heating can ruin the charger/analyzer.

Use care when inserting battery. Do not "slam" or slide the battery into the pocket, this could damage the

charger/analyzer.

Keep dirt and foreign objects out of the battery pocket. Do not short circuit any of the contacts in the battery pocket,

this could result in injury or property damage.

Do not operate the charger/analyzer if it has been dropped or damaged in any way. Return the charger/analyzer to

LXE.

Storing the HX2 Multi-Charger

Disconnect charger/analyzer by pulling the plug; not the cord.

Maintaining the HX2 Multi-Charger

Service should be performed by trained persons only. Return the charger/analyzer to LXE.

Caring for Batteries

Do not dispose of batteries into a fire. Burning will generate hazardous vapors and may cause the battery to explode.

Failure to observe this warning may result in injury from inhalation of vapors or burns from flying debris.

Do not immerse batteries in water or any other liquid. If batteries are immersed, contact LXE.

Do not disassemble or perform modifications to the battery. There are no user serviceable components in the battery.

Do not place battery into pocket or toolbox with conductive objects (coins, keys, tools, etc.).

A battery placed on damp ground or grass could be electrically shorted. Lay the battery on its side when not in use.

Do not store batteries above 140°F (60°C) for extended periods.

Failure to observe these warnings could result in injury or damage to the battery from rapid discharge of energy or

overheating of the battery.

Electrical Shock Hazards

The following precautions should be observed to avoid the risk of electrical shock hazards associated with charging

batteries:

The HX2 Multi-Charger has been designed for indoor use only. Do not operate outdoors or in extremely high

humidity environments. Do not expose charger/analyzer to rain, snow or wet conditions.

Unplug the charger/analyzer from power source before cleaning. Use only mild detergent with a slightly damp cloth

to clean the outside of the charger/analyzer. Do not use solvents or flammable cleaners. Allow the case to dry fully

before using again.

Use of attachments or accessories not recommended by LXE could result in fire, electric shock or injury.

This appliance must be properly grounded. If it should malfunction or break down, grounding provides a path of

least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having

an equipment grounding conductor and ground outlet that is properly installed and grounded in accordance with all

local codes and ordinances. Do not operate the charger/analyzer with a damaged AC cord or plug. LXE does not

recommend the use of any extension cord with the HX2 Multi-Charger.

The HX2 Multi-Charger has been designed for use on a nominal 100 or 120 volt or nominal 220 or 240 volt circuit

and has a grounding attachment plug. The plug is an IEC configuration that is appropriate for your country and

regulations. Make sure that the appliance is connected to an outlet having a configuration similar to the plug. No

adapter should be used with this appliance. Improper connection of the equipment-grounding conductor can result in

a risk of electric shock.

Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded.

Do not modify the plug provided with the appliance. If it will not fit in the outlet, have a proper outlet installed by a

qualified electrician.

Do not disassemble the HX2 Multi-Charger. It contains no user serviceable parts.

HX2 Multi-Charger Approvals/Standards

EMI/EMC Standards Safety Standards

FCC Part 15 Subpart B, Class A

EN 55022 Class A – (CISPR 22)

EN 55024:1998

AS/NZS 3548, Class A (CISPR 22)

UL 60950-1 / CSA C22.2 No. 60950-1

IEC/EN 60950-1

FCC Information:

This device complies with FCC Rules, part 15. Operation is subject to the following conditions:

1. This device may not cause harmful interference

and

2. This device must accept any interference that may be received, including interference that may cause undesired

operation.

Warning!

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to correct the interference at

his own expense.

Changes or modifications to this device not expressly approved by LXE Inc., could void the user’s authority to operate this

equipment.

EMC Directive Requirements:

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be

required to take adequate measures.

Industry Canada:

This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is

subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques

de Classe A prescrites dans le Règlement sur le brouillage radioélectrique édits par le ministère des Communications du Canada.

Important: This symbol is placed on the product to remind users to dispose of Waste Electrical and Electronic

Equipment (WEEE) appropriately, per Directive 2002-96-EC. In most areas, this product can be recycled,

reclaimed and re-used when properly discarded. Do not discard labeled units with trash. For information about

proper disposal, contact LXE through your local sales representative, or visit www lxe com.

Caution

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

Attention

II y a danger d’explosion s’il y a remplacement incorrect de la batterie.

Remplacer uniquement avec une batterie du même type ou d’un type equivalent recommandé par le

constructeur. Mettre au rebut les batteries usagées conformément aux instructions du fabricant.

DECLARATION OF CONFORMITY

according to

the Low Voltage Directive; 73/23/EEC

the EMC Directive; 89/336/EEC

and the Marking Directive; 93/68/EEC

Type of Equipment: Accessory battery charger and battery analyzer

Brand Name or Trademark: LXE

Type Designation: HX2 Battery Charger

Manufacturer: LXE Inc.

Address: 125 Technology Parkway

Norcross, GA 30092 USA

The following harmonized European Standards, technical specifications, or other normative documents,

have been applied:

EMI / EMC Standards:

EN 55022 : 1998 Limits and methods of measurement of radio disturbance

characteristics of information technology equipment

EN 55024 : 1998 Information Technology Equipment – Immunity characteristics

– Limits and methods of measurement

Safety Standards:

UL 60950-1 Safety of information technology equipment, including electrical

business equipment

The product carries the CE Mark:

We, LXE Inc., declare that the equipment specified above complies with all Essential Health and Safety

Requirements of the above Directives and Standards, as amended.

Date of issue: April 10, 2007

Cyril A. Binnom Jr.

Regulatory Engineer

Page is loading ...

E-EQ-HX2CHGROG-B HX2 Multi-Charger User’s Guide

Table of Contents

I

NTRODUCTION 1

Purpose of this Guide............................................................................................... 1

Quick Start................................................................................................................. 1

Intended Use ............................................................................................................. 1

Controls and Connectors......................................................................................... 2

HX2 Multi-Charger ..................................................................................................................2

Specifications............................................................................................................ 3

Electrical Specifications ...........................................................................................................

3

Operating Temperature Ranges ................................................................................................

3

Dimensions ...............................................................................................................................3

Battery Capacity .......................................................................................................................3

HX2 Rechargeable Lithium Ion Battery Pack.......................................................... 4

INSTALLATION AND OPERATION 5

Introduction............................................................................................................... 5

Normal Operations.................................................................................................... 5

Setup.......................................................................................................................... 6

Power Supply............................................................................................................................6

Orienting and Inserting the Battery Pack..................................................................................7

Charging a Battery.................................................................................................... 7

Using the Analyze / Charge Pocket ......................................................................... 8

Begin Analyzing .......................................................................................................................8

LEDs...........................................................................................................................

9

Charging Pocket LEDs .............................................................................................................9

Charger/Analyzer LEDs ...........................................................................................................9

Interpreting the LEDs ............................................................................................. 10

RED - on any pocket ........................................................................................................................ 10

RED FLASHING - on every pocket................................................................................................. 10

GREEN - on any pocket................................................................................................................... 10

YELLOW - on any pocket ............................................................................................................... 10

NO LIGHT - on a pocket.................................................................................................................. 10

NO LIGHT - on every pocket........................................................................................................... 10

Maintenance ............................................................................................................ 11

Storage .................................................................................................................... 11

Service .....................................................................................................................

11

Troubleshooting......................................................................................................

11

Getting Help............................................................................................................. 13

Accessories............................................................................................................. 13

ii Table of Contents

HX2 Multi-Charger User’s Guide E-EQ-HX2CHGROG-B

IMPORTANT SAFETY WARNINGS - TRANSLATIONS 14

Illustrations

Figure 1 HX2 Multi-Charger ............................................................................................................................2

Figure 2 Charging Pocket .................................................................................................................................2

Figure 3 Lithium Ion Battery Packs..................................................................................................................4

Figure 4 AC/DC Power Supply.........................................................................................................................6

Figure 5 Insert Battery in Charging Pocket.......................................................................................................7

Figure 6 Multi-charger Control Panel...............................................................................................................9

Figure 7 Charger/Analyzer LED Location........................................................................................................9

E-EQ-HX2CHGROG-B HX2 Multi-Charger User’s Guide

Introduction

Purpose of this Guide

This user’s guide is intended to familiarize the user with the safety and operating instructions

necessary to use the HX2 Multi-charger (Model HX2A310CHGR6US and

HX2A311CHGR6WW) to simultaneously charge up to six LXE Rechargeable HX2 Lithium Ion

Battery Packs:

• Standard Battery Pack (LXE HX2A301BATTSTD)

• Extended Battery Pack (LXE HX2A302BATTEXT)

This guide should be readily available to all users and maintenance personnel using the HX2

Multi-charger.

Quick Start

This guide provides the following instructions for operating the HX2 Multi-Charger.

• Setting Up the Charger

• Inserting the Battery Pack

• Interpreting the LEDs

• Using the Analyze/charge Pocket

Intended Use

The LXE HX2 Multi-Charger is designed to simultaneously charge up to six standard HX2

Rechargeable Lithium Ion Battery Packs in less than four hours, depending upon battery pack

temperature and conditions. The Extended battery packs require less than eight hours.

The charger/analyzer should be located in an area where it:

• Is not in high traffic areas.

• Has enough clearance to allow easy access to the power port on the back of the device.

• Is protected from rain, dust or inclement weather. This device is intended for indoor use

only.

• Is not located near hazardous materials.

Note: Store the multi-charger and batteries in a cool, dry place.

2 Controls and Connectors

HX2 Multi-Charger User’s Guide E-EQ-HX2CHGROG-B

Controls and Connectors

HX2 Multi-Charger

Figure 1 HX2 Multi-Charger

1 Front 5 Analyze LED

2 Battery Charging Pocket 6 Analyze Dome Switch

3 Battery Charge LED Indicator 7 Analyze Progress LEDs

4 Analyze Pocket 8 AC/DC Power Connector

1. Battery Well

2. Alignment Rib Apertures

3. Battery Charging Contacts

4. Battery Charge Progress LED

Figure 2 Charging Pocket

Note: Do not allow cleaning agents of any kind to contact the battery charging contacts; they

may be damaged. If necessary, clean them with a soft-bristle, dry brush or compressed

air.

Specifications 3

E-EQ-HX2CHGROG-B HX2 Multi-Charger User’s Guide

Specifications

Electrical Specifications

Parameter Min Max. Comment

Power Supply Input

Voltage (V

AC-IN

)

100 VAC 240VAC Auto-switching

Power Supply Input

Frequency (freq)

47Hz 63Hz

Note: Battery packs may leak up to 1mA current through the battery contacts when left in an unpowered multi-

charger battery well.

Operating Temperature Ranges

Minimum Maximum Comment

Operating -20°C (-4°F) +40°C (104°F) Battery packs can only be charged when their temperature

is between 10°C (50°F) and 40°C (104°F).

Charging 10°C (50°F) +40°C (104°F) Battery packs will not begin charging if their temperature

is outside this range.

Storage -20°C (-4°F) +70°C (160°F) Unit is off.

Dimensions

Weight Multi-charger – 15 oz / .43 kg (no batteries, no power connection)

Power Supply – 10 oz / .28 kg

Plug Type IEC320 (3 prong, grounded) / barrel connector

Length 11.25” (28.57 cm)

Width 4.25” (10.79 cm)

Height 1.70” (4.32 cm)

Battery Capacity

A battery pack with less than 70% capacity provides a significant reduction in the length of time it

can power the unit.

LXE Battery Pack Part

Number

Standard

HX2A301BATTSTD

Extended

HX2A302BATTEXT

Construction Lithium Ion Lithium Ion

Specified Capacity 2000mAh 4000mAh

70% of Specified Capacity 1400mAh 2800mAh

4 HX2 Rechargeable Lithium Ion Battery Pack

HX2 Multi-Charger User’s Guide E-EQ-HX2CHGROG-B

HX2 Rechargeable Lithium Ion Battery Pack

Each standard battery pack has one side alignment rib wider than the other to ensure the battery

pack is inserted in the battery charging pocket easily. This design ensures the battery charging

contacts line up with the charger contacts in each charging pocket. The extended battery’s ribs are

the same on each side.

Standard Battery Pack Model Number – HX2A301BATTSTD

Extended Battery Pack Model Number – HX2A302BATTEXT

Figure 3 Lithium Ion Battery Packs

Note: When a battery pack is not in use, lay the battery pack contact-side up in a protected

environment. When feasible, protect the battery from ESD and contamination. Any dust

or moisture that adheres to the tether connector can potentially cause damage upon

cable connection.

Battery Charge Contact Description

Power (+) Positive terminal 1

ID (D) Battery ID 2

Voltage Sense (S) Cell voltage sensor 3

Thermistor (T) Temperature sensor 4

Ground (-) Negative terminal 5

Introduction 5

E-EQ-HX2CHGROG-B HX2 Multi-Charger User’s Guide

Installation and Operation

Introduction

The life and capacity of a Lithium Ion battery can vary significantly depending on the discharge

current and the environment in which it is used. As with all batteries, expect to see a reduction in

the total number of operations a fully charged battery pack can deliver as it ages. When the battery

reaches end-of-life, it must be replaced.

Charging times may increase but will not exceed four hours for the Standard battery packs and

eight hours for the Extended battery packs. Battery packs do not need to be fully discharged

between charge cycles.

Analyzing times may increase but will not exceed 16 hours for the Standard battery packs and 32

hours for the Extended battery pack. Minimum analysis time is 8.5 hours. Typical analysis time is

approximately 12 hours for the Standard battery pack and 24 hours for the Extended battery pack.

Normal Operations

The optimal operating temperature range for the HX2 Multi-Charger is between 50°F and 104°F

(10°C and 40°C). While charging, the charger and battery pack will generate enough heat to feel

warm. This is normal and does not indicate a problem. Do not store the battery pack in direct

sunlight or anywhere the battery pack cannot cool down. If the battery pack is hot after removal

from the mobile device, allow it to cool at room temperature before placing it in the charger.

Charge times may increase significantly if the battery is warm or hot, since it takes the battery

pack longer to cool down while in the battery well. If the battery pack is hot from severe

environmental use and immediate recharging is necessary, place the battery pack in a cool air

stream or in a cool location until it is no longer warm to the touch before charging.

When a battery is placed in a charging pocket, the multi-charger begins charging the battery.

There is a slight delay while the multi-charger evaluates the condition of the battery (ambient

temperature, remaining charge, etc.) before charging begins.

Do not place, store or use the HX2 Multi-Charger in hazardous locations.

6 Setup

HX2 Multi-Charger User’s Guide E-EQ-HX2CHGROG-B

Setup

Ensure that the location you choose for the battery charger/analyzer is:

• Well ventilated.

• Is not in high traffic areas.

• Has enough clearance to allow easy access to the power port on the back of the device.

• Is protected from rain, direct sunlight, dust or inclement weather.

Power Supply

Figure 4 AC/DC Power Supply

1. Place the multi-charger on a horizontal, stable, hard surface.

2. Plug the power cord into a properly grounded outlet. An LED on the power supply, if

available, may illuminate.

3. Plug the power supply cable into the Power outlet on the back of the multi-charger.

4. On initial power-up, multi-charger LEDs light up for a few seconds.

5. The Multi-charger is ready for use.

Note: Multi-charger and power supply are designed for indoor use only, at a maximum ambient

temperature of 40

°

C (104

°

F).

Charging a Battery 7

E-EQ-HX2CHGROG-B HX2 Multi-Charger User’s Guide

Orienting and Inserting the Battery Pack

Caution!

It is important that battery packs are inserted into the charging/analyzing pocket

correctly. Inserting the battery incorrectly could result in damage to the battery pack

or the charger/analyzer.

When preparing the battery pack for insertion into an HX2 multi-charger pocket, hold the battery

with the HX2 cable connect interface up and the battery charging contacts in line with the

charging contacts in the charging pocket.

The alignment ribs will line up with the rib notches. Both the standard battery pack and extended

battery packs fit in all pockets.

Caution!

Do not “slam” the battery pack into the

charging or analyze/charge pocket.

Damage may result.

Figure 5 Insert Battery in Charging Pocket

Place the battery pack into the battery charging pocket, lining up the rib notches on the battery and

the pocket. Firmly press the battery down into the charging pocket until it is fully inserted.

The battery alignment ribs fit snugly in both rib notches on either side of the battery charging

pocket. If they do not, remove the battery and turn it around, keeping the HX2 cable interface

uppermost, until the alignment ribs fit correctly in the charging pocket.

Charging a Battery

The HX2 Multi-Charger indicates the status of a battery pack in the charging pocket with an LED

located below each pocket. There are six charging pockets available that can hold and charge the

Standard and the Extended battery pack.

8 Using the Analyze / Charge Pocket

HX2 Multi-Charger User’s Guide E-EQ-HX2CHGROG-B

Using the Analyze / Charge Pocket

The analyze/charge pocket is the one closest to the HX2 Multi-charger label and the Analyze

dome switch. The analyze/charge pocket can be used to:

• Charge a standard battery pack in less than four hours.

• Charge an Extended battery pack in less than 8 hours.

• Analyze a standard battery pack, ending with the battery pack fully charged, in less than

twelve hours.

• Analyze an extended battery pack, ending with the battery pack fully charged, in less than

32 hours.

Begin Analyzing

Press the Analyze dome switch within 15 seconds of inserting the battery in the Analyze pocket to

start the Analyze (Charge – Discharge – Charge) process. See figure titled “Analyzer LED

Location”.

If the analyze dome switch is not pressed within 15 seconds, the battery will be charged, but not

analyzed.

The Analyze progress LEDs indicate the battery capacity as a percent of the original value.

When the Analyze dome switch has been pressed, the Analyze LED will illuminate Red to

indicate that the battery testing has started. As the analysis proceeds and during the discharge

activity, the four progress LEDs at the side of the battery pocket will illuminate in sequence to

indicate the capacity of the battery . The Analyze LED is Green when the process is finished. The

battery is then ready for use provided the capacity is acceptable.

LEDs 9

E-EQ-HX2CHGROG-B HX2 Multi-Charger User’s Guide

LEDs

Charging Pocket LEDs

The status of the charge operation is communicated by the LED located at the base of each

charging pocket. See previous figure titled “HX2 Multi-charger” for LED location.

LED

Indication Description

Off No Battery/power Battery pack not plugged in or no power applied.

Green Charged Battery pack fully charged.

Red Charging Battery pack charging.

Yellow Standby Battery pack temperature out of range.

Flashing Red

on any station

Fault Battery pack fault or failure.

Flashing Red

on any station

Timeout Battery analyzer’s 4.5 hour timeout period

expired.

Flashing Red

on all stations.

Charger/Analyzer

Failure

Battery analyzer fault or failure.

Figure 6 Multi-charger Control Panel

Charger/Analyzer LEDs

1. Analyze/Charge Percentage of

Original value

2. Analyze Dome switch

3. Analyze/Charge Pocket LED

Figure 7 Charger/Analyzer LED Location

The Analyze progress LEDs indicate the battery capacity as a percent of the original value.

10 Interpreting the LEDs

HX2 Multi-Charger User’s Guide E-EQ-HX2CHGROG-B

Percentage of Battery

Capacity

Between 90%

and 100%

Between 80%

and 90 %

Between 70%

and 80%

Between 50%

and 70%

On Off Off Off

On On Off Off

On On On Off

On On On On

Analyze

Progress

LED Status

When all LEDs are off, the battery capacity is less than 50%.

Interpreting the LEDs

Each pocket on the Multi-Charger has an LED. The LED located at the base of each pocket

communicates the status of the charge operation.

Note: On initial power-up, all six pocket LEDs will light yellow, red, green for 1 second

before turning off.

RED - on any pocket

Continuous Battery pack - Charging (any charge pocket).

Charging or analyzing (analyze/charge pocket).

Flashing Battery pack fault or failure.

Battery charger timeout period expiration.

RED FLASHING - on every pocket

Battery charger fault or failure.

GREEN - on any pocket

Continuous Battery pack charge complete - Ready.

YELLOW - on any pocket

Continuous Battery pack temperature is out of range - Standby.

NO LIGHT - on a pocket

No battery pack installed.

Defective or damaged battery pack or charger. Refer to “Troubleshooting.”

NO LIGHT - on every pocket

No battery packs installed.

No power applied to the Multi-Charger.

Maintenance 11

E-EQ-HX2CHGROG-B HX2 Multi-Charger User’s Guide

Maintenance

Use a clean soft cloth to wipe any dirt, moisture or grease from the battery pack, contacts or the

charger. Do not use any liquid to clean the battery pack or charger contacts. Any dust or moisture

that adheres to the tether connector can potentially cause damage upon cable connection.

Storage

Battery packs should be kept in a cool, dry place whenever possible. Do not store battery packs in

direct sunlight, on a metal surface, or anywhere the battery pack cannot cool down. Do not leave

the battery pack in a non-operating charger. The battery pack may discharge through the charger

rather than hold its charge.

Service

There are no user serviceable parts in the Rechargeable Lithium Ion Battery Pack or the HX2

Multi-Charger. Should your charger require service, contact LXE.

Troubleshooting

The following is intended as an aid in determining whether the battery pack or the charger may be malfunctioning.

Problem Cause Solution

Battery pack does not fit in

battery well.

Different manufacturer's battery

pack, or there is an object in the

battery well.

Alignment ribs

Check if the battery pack is LXE part

number: HX2A301BATTSTD or

HX2A302BATTEXT.

If not, do not use. Remove the object

from the battery well.

Turn the battery pack until the curved

part of the charging pocket matches up

with the curved part of the battery pack.

Make sure the HX2 cable connector is

up.

No battery pack in charger, but

any of the LEDs are on.

Dirt or foreign objects are in the

battery pocket.

Unplug charger from outlet. Remove any

dirt or foreign objects from battery

pockets. If the LEDs continue to remain

ON, the charger may be defective. Return

charger to an authorized LXE service

center.

Charger is plugged into a live

outlet, battery pack is inserted,

but RED LED is OFF and no

other LEDs are on, or all LEDs

are off.

• Battery pack is not making

contact with charging

terminals in the battery

pocket.

• Faulty battery pack.

• New battery pack, same

result.

• Push battery pack in firmly. Do not

"slam" the battery pack into the

battery well.

• Replace battery pack.

• Contact LXE for replacement

options.

12

HX2 Multi-Charger User’s Guide E-EQ-HX2CHGROG-B

Problem Cause Solution

When you first put a fully

charged battery pack in the

battery well, the RED LED

comes on, indicating the battery

pack is charging.

During the first few minutes, the

charger checks the battery pack

for correct voltage and charge

state. During this time the LED

is RED and is continuously ON.

After charging is complete, the

LED is GREEN.

There is nothing wrong with the battery

pack or charger.

Current could not be sourced

through the battery pack due to

age, exhaustion or damage to

the cell(s). The battery pack

does not communicate with the

charger.

OR

Contact LXE for battery pack

replacement options.

The battery pack voltage has not

reached 6.0V within 30 minutes

and the charger has timed out.

OR

Contact LXE for battery pack

replacement options.

LED is flashing RED at any

station.

The charger’s timeout period

has expired.

Make sure that the battery pack

temperature is within specification and

retry charging. If problem repeats,

contact LXE for battery pack replacement

options.

Solid YELLOW LED when

battery pack is inserted in the

charger.

The battery pack is too hot or

too cold to charge.

Remove battery pack from the charger

and allow it to adjust to room

temperature.

Note: If the battery pack is left in the

charger, it will cool down or warm to a

temperature upon which the charger will

begin the charge cycle. However,

depending on the temperature of the

battery, it may take 2-3 hours to adjust.

The cool-down or warm-up of a battery

pack is much quicker if the battery is not

in the battery pocket.

Getting Help 13

E-EQ-HX2CHGROG-B HX2 Multi-Charger User’s Guide

Getting Help

LXE manuals are now available on one CD and they can also be viewed/downloaded from the

LXE ServicePass website. Contact your LXE representative to obtain the LXE Manuals CD. You

can also check the LXE ServicePass website for the latest releases of LXE manuals.

You can get help from LXE by calling the telephone numbers listed on the LXE Manuals CD, in

the file titled "Contacting LXE". This information is available on the LXE ServicePass website.

Explanations of terms and acronyms used in this manual are located in the file titled "LXE

Technical Glossary" on the LXE Manuals CD and on the LXE ServicePass website.

Accessories

Note: Items with a Green letter R in the second column are ROHS-compliant. Please contact

your LXE representative when ordering ROHS-compliant items as the part number may

have changed. Items without the letter R may have received ROHS-compliance after this

guide was published. E designator means the accessory is RoHS Exempt.

HX2 Standard Battery, Lithium Ion

E

HX2A301BATTSTD

HX2 Extended Battery, Lithium Ion

E

HX2A302BATTEXT

6 slot battery charger with universal power supply.

Includes analyzing capabilities on one slot. US power

cord included.

R

HX2A310CHGR6US

6 slot battery charger with universal power supply.

Includes analyzing capabilities on one slot. Power cord

not included.

R

HX2A311CHGR6WW

Page is loading ...

LXE HX2A3116 User manual

This manual is also suitable for

LXE HX2A3116 User manual

in other languages

Related papers

Other documents