Sharper Image 55-1550 User manual

Sharper Image
Brand
Sharper Image
Model
55-1550
Category
Fitness, gymnastics & weight training
Type
User manual

This manual is also suitable for

When calling for parts or
service, please specify
the following number
:
Model#: 55-1550
CAUTION:
Weight on this product should not exceed 250 lbs.
Owner's
Manual
This Product is Produced Exclusively by
2040 N. Alliance, Springeld, MO 65803
Customer Care
1 (800) 375-7520
www.staminaproducts.com
Product May Vary Slightly From Pictured.
!
WARNING
!
Exercise can present a
health risk. Consult a
physician before beginning
any exercise program with
this equipment. If you feel
faint or dizzy, immediately
discontinue use of this
equipment. Serious bodily
injury can occur if this
equipment is not assembled
and used correctly. Serious
bodily injury can also occur
if all instructions are not
followed. Keep others and
pets away from equipment
when in use. Always make
sure all bolts and nuts are
securely tightened prior to
each use. Follow all safety
instructions in this manual.
STAMINA PRODUCTS
MADE IN CHINA
©
2016 Stamina Products, Inc.
2017, 04
TABLE OF CONTENTS
Safety Instructions ...................................... 2
Before You Begin ........................................ 4
Equipment Warning & Notice Labels ........ 5
Hardware Identication Chart .................... 6
Assembly Instructions ................................ 7
Operational Instructions ........................... 13
Storage ....................................................... 16
Maintenance ............................................... 16
Warranty ..................................................... 17
Product Parts Drawing .............................. 18
Parts List .................................................... 19
Notes ........................................................... 21
Fax/Mail Ordering Form ............................ 22
2
SAFETY INSTRUCTIONS
1. Save these instructions and ensure that other exercisers read this manual prior to using the inLine®
Inversion Chair for the rst time.
2. Read all warnings and cautions posted on the inLine® Inversion Chair.
3. The inLine® Inversion Chair should only be used after a thorough review of the Owner's Manual. Make
sure that it is properly assembled and tightened before use.
4. We recommend that two people be available for assembly of this product.
5. Do not use the inLine® Inversion Chair alone. Always have a helper available in case assistance is
needed in recovering from the decline position.
6. You must understand how to recover from the inverted position before using the inLine® Inversion Chair.
7. Keep children away from the inLine® Inversion Chair. Do not allow children to use or play on the inLine®
Inversion Chair. Keep children and pets away from the inLine® Inversion Chair when it is in use.
8. The inLine® Inversion Chair should not be used by persons weighing more than 250 lbs.
9. The inLine® Inversion Chair should not be used by persons over 6 feet 6 inches tall.
10. It is recommended that you place this exercise equipment on an equipment mat.
11. Set up and operate the inLine® Inversion Chair on a solid level surface. Do not position the inLine®
Inversion Chair on loose rugs or uneven surfaces.
12. Be sure the inLine® Inversion Chair is placed in an area where there is enough room for the seat to rotate
completely.
13. Always use the Seat Belt(60). Make sure the Seat Belt(60) is securely fastened before inverting.
14. Do not wear loose or dangling clothing while using the inLine® Inversion Chair.
15. Use the inLine® Inversion Chair only as described in the manual.
16. Before using, inspect the inLine® Inversion Chair for worn or loose components, and securely tighten or
replace any worn or loose components prior to use.
17. Be careful to maintain your balance while using, mounting, dismounting, or assembling the inLine®
Inversion Chair, loss of balance may result in a fall and serious bodily injury.
18. The inLine® Inversion Chair is for consumer use only. It is not for use in public or semipublic facilities.
19. Do not use the inLine® Inversion Chair if you have any of the following conditions or ailments:
!
WARNING
This product contains a chemical known to the State of California to cause cancer and
birth defects or other reproductive harm.
Consult your physician before starting this or any exercise program. This is especially
important if you are over the age of 35, have never exercised before, are pregnant,
or suer from any health problem. This product is for home use only. Do not use in
institutional or commercial applications. Failure to follow all warnings and instructions
could result in serious injury or death.
To reduce the risk of serious injury, read the following Safety Instructions before using
the inLine® Inversion Chair.
!
WARNING
!
WARNING
Extreme obesity
Glaucoma, retinal detachment or conjunctivitis
Pregnancy
Spinal injury, Cerebral Sclerosis, or acutely swollen joints
Middle ear infection
High blood pressure, hypertension, recent stroke or transient ischemic attack
Heart or circulatory disorders for which you are being treated
Hiatus hernia or ventral hernia
Bone weaknesses including osteoporosis, unhealed fractures, medullary pins, or surgically
implanted orthopedic supports.
Use of anti-coagulants including aspirin in high doses.
NEED HELP?
CONTACT US FIRST
1 (800) 375-7520
customer.care@staminaproducts.com
Hi! From all of us here at Stamina Products, thank you for your purchase. We
know that you have big fitness goals in mind and we are here to help you along.
Call us, email us, or send us a message on Facebook. Be sure to contact us if you
have any questions on your new product. We look forward to hearing from you!
With your body in mind,
Stamina Customer Care
To enact your extended warranty and to help us better
serve you, please go online and register your new product.
register.staminaproducts.com
ONLINE
customer.care@staminaproducts.com
www.staminaproducts.com
TELEPHONE
1 (800) 375-7520
FAX
(417) 889-8064
MAIL
Stamina Products, Inc.
ATTN: Customer Care
P.O. Box 1071
Springfield, MO 65801-1071
facebook.com/StaminaProducts
facebook.com/AeroPilates
CUSTOMER CARE HOURS:
Monday-Thursday, 7:30 AM-5:00 PM, Central Time
Friday, 8:00 AM-3:00 PM, Central Time
It is quick and easy to register online, but if you’re a little old school or just need a
reason to raise that little flag on your mailbox, fill out the info on the last page of this
manual and mail it in.
THE FOLLOWING TOOLS ARE INCLUDED FOR ASSEMBLY :
BEFORE YOU BEGIN
4
Allen Wrench (5mm)
Allen Wrench (6mm)
Warning Label
Security Belt
Handrail
Back Cushion
Leg Adjustment Frame
Handrail
Seat Belt
Front Pivot Arm
Swing Bar
Rear Frame
Foam Pad
Seat
Lever
Round Stand
Front Frame
Combination Wrench
Allen Wrench (4mm)
Thank you for choosing the inLine® Inversion
Chair. We take great pride in producing this quality
product and hope it will provide many hours of
quality exercise to make you feel better, look
better, and enjoy life to its fullest.
It's a proven fact that a regular exercise program
can improve your physical and mental health.
Too often, our busy lifestyles limit our time and
opportunity to exercise. The inLine® Inversion
Chair provides a convenient and simple method to
begin your journey of getting your body in shape
and achieving a happier and healthier lifestyle.
Before reading further, please review the
drawing below and familiarize yourself with the
parts that are labeled.
Read this manual carefully before using the
inLine® Inversion Chair.
Although Stamina constructs its products with
the nest materials and uses the highest standards
of manufacturing and quality control, there can
sometimes be missing parts or incorrectly sized
parts. If you have any questions or problems with
the parts included with your inLine® Inversion
Chair, please do not return the product. Contact us
FIRST!
If a part is missing or defective, please go to
staminaproducts.com under the Customer Care
section and order the part needed, or call us toll
free at 1-800-375-7520 (in the U.S.). Our Customer
Care Staff is available to assist you from 7:30
A.M. to 5:00 P.M. (Central Time) Monday through
Thursday and 8:00 A.M. to 3:00 P.M. (Central
Time) on Friday.
Be sure to have the name and model number of
the product available when you contact us.
Front Support
Front Pivot Arm
Back Frame
Labels are larger than actual size
This chart is provided to help identify the warning and notice labels on the InLine® Inversion Chair.
Please take a moment to familiarize yourself with all of the warning and notice labels.
EQUIPMENT WARNING & NOTICE LABELS
WARNING LABEL(62)W1
5
INVERSION WARNING DECAL(63)W2
WARNING
!
Consult your physician before starting this or any exercise program. This is
especially important if you are over the age of 35 or have any pre-existing
health condition. Always make sure all nuts and bolts are securely tightened
before using this product. This product should not be used by persons
weighing more than 250 lbs. unless otherwise stated in your Owner’s Manual.
Keep others including children & pets away from equipment when in use.
For consumer use only. Failure to follow all warnings
and instructions could result in serious injury or death.
Before assembling or using this product, read and
follow the Owner’s Manual and all other warnings and
instructions that accompany this product. Replace this
warning label if damaged, illegible, or removed.
57 Nylock Nut (M10 x 1.5) 5
58 Nylock Nut (M8 x 1.25) 10
59 Nylock Nut (M6 x 1) 2
52 Washer (M10) 11
53 Washer (M8) 12
55 Washer (M6) 8
Part Number and Description Qty
54 Arc Washer (M8) 12
56 Arc Washer (M6) 4
61 Bolt, Flat Head (M6 x 1 x 20mm) 1
6
length
length
mm.
in.
INCHES
This chart is provided to help identify the fasteners used in the assembly process. Place the washers or
the ends of the bolts or screws on the circles to check for the correct diameter. Use the small scale to
check the length of the bolts and screws.
NOTICE: The length of all bolts and screws, except those with flat
heads, is measured from below the head to the end of the bolt
or screw. Flat head bolts and screws are measured from the
top of the head to the end of the bolt or screw.
After unpacking the unit, open the hardware bag and make sure that you have all the following
fasteners. Some fasteners may be already attached to the parts.
MILLIMETERS
0 10 20 30 40 50 60 70 80 90
100
110
120
130 140
150
0 1/2
1 1/2
2 1/2
3 1/2
4 1/2
5 1/2
6
6 8
10
12
3/16"
1/4"
5/16" 3/8" 1/2"
HARDWARE IDENTIFICATION CHART
48 Bolt, Button Head (M8 x 1.25 x 20mm) 2
50 Bolt, Button Head (M6 x 1 x 35mm) 2
51 Bolt, Button Head (M6 x 1 x 20mm) 9
40 Bolt, Button Head (M10 x 1.5 x 90mm) 1
41 Bolt, Button Head (M10 x 1.5 x 65mm) 4
42 Bolt, Button Head (M8 x 1.25 x 85mm) 1
43 Bolt, Button Head (M8 x 1.25 x 65mm) 2
44 Bolt, Button Head (M8 x 1.25 x 60mm) 1
45 Bolt, Button Head (M8 x 1.25 x 50mm) 4
46 Bolt, Button Head (M8 x 1.25 x 45mm) 4
47 Bolt, Button Head (M8 x 1.25 x 40mm) 2
ASSEMBLY INSTRUCTIONS
STEP 1
Insert the FRONT FRAME(1) into the brackets on the REAR FRAME(3) and secure with BUTTON
HEAD BOLTS(M8x1.25x50mm)(45), WASHERS(M8)(53), and NYLOCK NUTS(M8x1.25)(58).
STEP 2
Attach the FRONT SUPPORT(2) to the FRONT FRAME(1) with BUTTON HEAD BOLTS
(M8x1.25x45mm)(46), ARC WASHERS(M8)(54), and NYLOCK NUTS(M8x1.25)(58).
7
Place all parts from the box in a cleared area and position them on the oor in front of you. Remove
all packing materials from your area and place them back into the box. Do not dispose of the packing
materials until assembly is completed. Read each step carefully before beginning. If you are missing
a part, please go to staminaproducts.com under the Customer Care section and order the part
needed, e-mail us at customer[email protected], or call us toll free at 1-800-375-7520 (in
the U.S.). Our Customer Care Sta is available to assist you from 7:30 A.M. to 5:00 P.M. (Central
Time) Monday through Thursday and 8:00 A.M. to 3:00 P.M. (Central Time) on Friday.
ASSEMBLY INSTRUCTIONS
STEP 3
Attach the BACK FRAME(5) to the REAR FRAME(3) with BUTTON HEAD BOLTS (M10x1.5x65mm)(41),
WASHERS(M10)(52), and NYLOCK NUTS(M10x1.5)(57) on both sides.
STEP 4
Place the SWING BAR(9) into the gap in the SEAT FRAME(7), then secure by inserting the SHAFT(12)
through the SEAT FRAME(7) and SWING BAR(9). Attach the FRONT PIVOT ARMS(6) to both ends
of the SHAFT(12) with BUTTON HEAD BOLTS(M6x1x35mm)(50), ARC WASHERS(M6)(56), and
NYLOCK NUTS(M6x1)(59).
8
ASSEMBLY INSTRUCTIONS
STEP 5
Attach the FRONT PIVOT ARMS(6) to the REAR FRAME(3) with BUTTON HEAD BOLTS
(M10x1.5x65mm)(41), WASHERS(M10)(52), and NYLOCK NUTS(M10x1.5)(57) on both sides.
STEP 6
Attach the SEAT FRAME(7) to the BACK FRAME(5) with BUTTON HEAD BOLT(M10x1.5x90mm)(40),
WASHERS(M10)(52), and NYLOCK NUT(M10x1.5)(57).
STEP 7
Attach the LINKAGE(8) to the BACK FRAME(5) with BUTTON HEAD BOLT(M8x1.25x85mm)(42),
WASHERS(M8)(53), and NYLOCK NUT(M8x1.25)(58).
9
ASSEMBLY INSTRUCTIONS
STEP 8
Refer to detail view A and the illustration below. Attach the ANGLE ADJUSTMENT BELT(16) to the
FRONT SUPPORT(2) with BUTTON HEAD BOLT(M8x1.25x60mm)(44), WASHERS(M8)(53), and
NYLOCK NUT(M8x1.25)(58).
STEP 9
Refer to the bottom view of the illustration below. Align the hook and loop pad on the HINGE WEAR
COVER(15) and the SEAT(13), then press them to attach together.
STEP 10
Attach the SEAT(13) to the SEAT FRAME(7) with ROUND HEAD BOLTS(M6x1x20mm)(51) and
WASHERS(M6)(55).
Bottom View
hook and
loop pad
10
A.
ASSEMBLY INSTRUCTIONS
11
STEP 11
Attach the SEAT BELT(60) to the BACK FRAME(5) with FLAT HEAD BOLT(M6x1x20mm)(61) and
WASHER(M10)(52).
CAUTION: Always use the SEAT BELT(60). Make sure the SEAT BELT(60) is securely fastened before
inverting.
STEP 12
Refer to the Back View of the illustration below. Align the hook and loop pad on the HINGE WEAR
COVER(15) and the BACK CUSHION(14), then press them to attach together. Attach the BACK
CUSHION(14) to the BACK FRAME(5) with BUTTON HEAD BOLTS(M6x1x20mm)(51) and WASHERS
(M6)(55).
NOTE: Pull the upper part of the BACK CUSHION(14) back and invert the system so that the BACK
CUSHION(14) and SEAT(13) are in the same plane. Check that the HINGE WEAR COVER(15)
is not too tight or too loose when the unit is in its inverted position. If necessary, adjust the
position of the HINGE WEAR COVER(15) on the BACK CUSHION(14) and the SEAT(13).
Back View
hook and
loop pad
ASSEMBLY INSTRUCTIONS
12
STEP 13
Insert the upper end of the HANDRAIL(4) into the REAR FRAME(3) and secure with BUTTON HEAD
BOLT(M8x1.25x40mm)(47). Do no tighten the bolt. Attach the lower end of the HANDRAIL(4)
to the REAR FRAME(3) with BUTTON HEAD BOLT(M8x1.25x20mm)(48), BUTTON HEAD
BOLT(M8x1.25x65mm)(43), and ARC WASHERS(M8)(54). Tighten the BUTTON HEAD BOLT
(M8x1.25x40mm)(47). Repeat on other side.
STEP 14
Pull the ADJUSTMENT KNOB(28) and insert the LEG ADJUSTMENT FRAME(10) into the SWING
BAR(9). Bolt the ROUND HEAD BOLT(M6x1x20mm)(51) into the SWING BAR(9).
NOTE: The pin on the ADJUSTMENT KNOB(28) must be inserted into one of the adjustment holes in
the LEG ADJUSTMENT FRAME(10). The ADJUSTMENT KNOB(28) should be screwed in tight
to make the LEG ADJUSTMENT FRAME(10) t securely in the SWING BAR(9).
STEP 15
Insert the FOAM PAD TUBES(39) through the LEG ADJUSTMENT FRAME(10) and the LEVER(11).
Slide the FOAM PADS(36) onto both sides of the FOAM PAD TUBES(39). Press the ROUND
PLUGS(20) into the FOAM PAD TUBES(39).
This belt is used to control the inversion decline angle of the
inLine® Inversion Chair. For a steeper decline angle, adjust the
buckle higher to lengthen the belt. For a less steep angle, adjust
the buckle lower to shorten the belt. Check the decline angle as
you like before using the inLine® Inversion Chair.
13
OPERATIONAL INSTRUCTIONS
GENERAL PRECAUTIONS
1. Do not use the InLine® Inversion Chair alone. Always have a helper available in case assistance is
needed in recovering from the decline position.
2. Always use the SEAT BELT(60). Make sure the SEAT BELT(60) is securely fastened before inverting.
3. Make sure that the LEG ADJUSTMENT FRAME(10) is properly set for your height.
4. Make sure that the FOAM PADS(36) are holding your feet properly.
5. Make sure that there is enough room for the InLine® Inversion Chair to rotate completely.
THE ANGLE ADJUSTMENT BELT
Buckle
FOAM PAD USE AND LEVER ADJUSTMENT
1. Place your feet under the FOAM PADS(36) with your ankles
between the FOAM PADS(36).
2. Press the BUTTON(25) down and pull the LEVER(11) toward
you until your ankles are comfortably yet rmly held between
the FOAM PADS(36).
3. To release your feet or relax the grip, press the BUTTON(25)
down and push the LEVER(11) forward.
OPERATIONAL INSTRUCTIONS
14
Proper adjustment of the LEG ADJUSTMENT FRAME(10) is very
important.
1. Loosen the ADJUSTMENT KNOB(28) on the SWING BAR(9).
2. Pull the ADJUSTMENT KNOB(28) and slide the LEG
ADJUSTMENT FRAME(10) to adjust.
3. Sit on the machine to make sure you feel comfortable with the
FOAM PADS(36).
4. Tighten the ADJUSTMENT KNOB(28) after adjustment.
LEG HEIGHT ADJUSTMENT
THE SEAT BELT
CAUTION: Always use the SEAT BELT(60). Make sure the SEAT
BELT(60) is securely fastened before inverting.
Sit on the SEAT(13), then buckle the SEAT BELT(60) snugly
around your waist.
THE HANDRAILS
The HANDRAILS(4) are located on both sides of the inLine®
Inversion Chair. The HANDRAILS(4) are to help you return from
inversion to the upright position. Pull the HANDRAILS(4) and pull
yourself to the upright position.
OPERATIONAL INSTRUCTIONS
1. Always use the SEAT BELT(60). Make sure the SEAT BELT(60) is securely fastened before inverting.
2. Start by sitting on the machine and leaning back on the BACK CUSHION(14) with your hands at your
side, or resting on your thighs.
3. Use the HANDRAILS(4) and both hands to rotate the BACK CUSHION(14) slowly backward until the
inversion stopped by the ANGLE ADJUSTMENT BELT(16).
4. It is recommended that the InLine® Inversion Chair be used for ve or ten minutes each morning, and
again each evening.
5. Grasp the HANDRAILS(4), and pull yourself to the upright position.
USING THE InLine® Inversion Chair
SUGGESTIONS FOR USE
15
1. Always use the SEAT BELT(60). Make sure the SEAT BELT(60) is securely fastened before inverting.
2. Begin slowly: invert only 15-20 degrees to begin with. Stay inverted only as long as you are
comfortable. Return upright slowly. If you feel unstable grab the HANDRAILS(4) and pull yourself up
slowly.
3. Make gradual changes: increase the angle only if it is comfortable. Increase the angle only a few
degrees at a time. Increase the time of use 1-2 minutes up to ten over a period of weeks. Add
stretching and light exercise only after you are comfortable with inversion.
4. Watch your body: come up slowly, dizziness after a session means you came up too fast. Wait a while
after eating before using the InLine® Inversion Chair. If you get nauseous, do not ght it, grab the
HANDRAILS(4) and come up as soon as you feel queasy.
5. Keep moving: movement while inverted encourages blood, lymph, and spinal uid circulation and aids
in alignment of bones and organs. Movement may be accomplished by either rhythmic traction or light
exercise. Do not exercise strenuously while inverted. Limit partial inversion without movement to one
or two minutes. Limit full inversion with no movement to only a few seconds.
6. Invert regularly: we recommend two or three times a day depending upon your current condition. Try
to schedule it for the same times each day.
The safety and integrity designed into the InLine® Inversion Chair can only be maintained when the
InLine® Inversion Chair is regularly examined for damage and wear. Special attention should be given
to the following:
STORAGE
MAINTENANCE
16
1. To store the InLine® Inversion Chair, simply keep it in a clean dry place.
2. Move the InLine® Inversion Chair by lifting the frame and moving slowly.
NOTE: Two people are required to move the InLine® Inversion Chair.
1. It is the sole responsibility of the user/owner to ensure that regular maintenance is performed.
2. Check the angle adjustment belt, seat belt, pivot arms, cushions, foam pads, adjustment knob, and
lever device for damage and wear.
3. Verify that all nuts and bolts are present and properly tightened. Replace missing nuts and bolts.
Tighten loose nuts and bolts.
4. Worn or damaged components shall be replaced immediately or the InLine® Inversion Chair
removed from service until repair is made.
5. Verify that the WARNING LABEL(62) is in place and easy to read. Call Stamina Products immediately
at 1-800-375-7520 for a replacement WARNING LABEL(62) if it is missing or damaged.
6. Only Stamina Products supplied components shall be used to maintain/repair the InLine® Inversion
Chair.
7. Keep your InLine® Inversion Chair clean by wiping it o with an absorbent cloth after use.
LIMITED WARRANTY
WARRANTY
MODEL 55-1550
17
Stamina Products, Inc. (“Stamina”) warrants to the original purchaser that this product will be free from
defects in materials and workmanship that arise under normal use, service, proper assembly and proper
operation in accordance with product warnings/instructions for a period of 90 days on the parts and three
years on the frame from the date of the original purchase from an authorized retailer. THIS WARRANTY
SHALL NOT APPLY TO ANY PRODUCT WHICH HAS BEEN SUBJECT TO COMMERCIAL USE,
ABUSE, MISUSE, ALTERATION OF ANY KIND OR TO ANY DEFECT OR CHANGE CAUSED BY
IMPROPER ASSEMBLY, REPAIR, REPLACEMENT, SUBSTITUTION OR USE WITH PARTS NOT
PROVIDED BY STAMINA. Commercial use includes use of product in athletic clubs, health clubs, spas,
gyms, and all other public or semipublic facilities whether or not the product’s use is in furtherance of a
prot making enterprise, and all other use which is not for personal purposes.
To implement this limited warranty, send a written notice stating your name, date, and place of purchase
and a brief description of the defect along with your receipt to Stamina Products, Inc. P.O. Box 1071,
Springeld Missouri, USA, 65801-1071, or email us at customer[email protected], or call us
at 1-800-375-7520. If the defect is covered under this limited warranty, you will be requested to return the
product or part to us for free repair or replacement at our option.
NO ACTION FOR BREACH OF THIS LIMITED WARRANTY MAY BE COMMENCED MORE
THAN ONE (1) YEAR AFTER THE DATE THE ALLEGED BREACH WAS OR SHOULD HAVE
BEEN DISCOVERED. NO ACTION FOR BREACH OF ANY IMPLIED WARRANTY (INCLUDING
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE) MAY BE COMMENCED
MORE THAN ONE (1) YEAR AFTER DELIVERY OF THE PRODUCT TO THE PURCHASER. These
warranties are not transferable. IF ANY PART OF THE PRODUCT IS NOT IN COMPLIANCE
WITH THIS LIMITED WARRANTY OR ANY IMPLIED WARRANTY, THE REMEDY OF REPAIR OR
REPLACEMENT IS THE EXCLUSIVE REMEDY. If any claim is made under this limited warranty or any
implied warranty, Stamina reserves the right to require the product to be returned for inspection, at the
purchaser’s expense, to Stamina’s premises in Springeld, Missouri. Return of the enclosed warranty
registration card is not required for warranty coverage, but is merely a way of establishing the date and
place of purchase.
Stamina SHALL NOT BE LIABLE FOR THE LOSS OF USE OF ANY PRODUCT, LOSS OF TIME,
INCONVENIENCE, COMMERCIAL LOSS OR ANY OTHER INDIRECT, CONSEQUENTIAL, SPECIAL
OR INCIDENTAL DAMAGES DUE TO BREACH OF THE ABOVE WARRANTY OR ANY IMPLIED
WARRANTY.
THIS LIMITED WARRANTY IS THE ONLY EXPRESS WARRANTY. NO ORAL OR WRITTEN
INFORMATION GIVEN BY STAMINA, ITS AGENTS OR EMPLOYEES, SHALL CREATE A WARRANTY
OR IN ANY WAY INCREASE THE SCOPE OF THIS WARRANTY. This warranty gives you specic legal
rights, and you may also have other legal rights which vary from state to state. ANY OTHER RIGHT
WHICH YOU MAY HAVE, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED IN DURATION TO THE DURATION OF THIS
WARRANTY.
The laws in some states aect the disclaimer or limitation of implied warranties and consequential and
incidental damages. If any such law is found applicable, the foregoing disclaimers and limitations of and
on implied warranties and consequential and incidental damages shall be deemed to be modied to the
extent necessary to comply with applicable law.
PRODUCT PARTS DRAWING
18
BACK
FRONT
PART# PART NAME QTY
1 Front Frame 1
2 Front Support 1
3 Rear Frame 1
4 Handrail 2
5 Back Frame 1
6 Front Pivot Arm 2
7 Seat Frame 1
8 Linkage 1
9 Swing Bar 1
10 Leg Adjustment Frame 1
11 Lever 1
12 Shaft 1
13 Seat 1
14 Back Cushion 1
15 Hinge Wear Cover 1
16 Angle Adjustment Belt 1
17 Round Stand 2
18 Bumper 1
19 Sleeve 1
20 Round Plug (19 mm) 4
21 Oval Endcap (20 x 60mm) 2
22 Square Plug (33.4 x 33.4mm) 1
23 Square Plug (38 x 38mm) 1
24 Hand Grip 1
25 Button 1
26 Stand 2
27 Stopper 1
28 Adjustment Knob 1
29 Pivot Arm Bushing 8
30 Back Frame Bushing 2
31 Linkage Bushing 4
32 Swing Bar Bushing 2
33 Seat Frame Bushing 4
34 Spring 1
35 Pressing Bar 1
36 Foam Pad 4
37 Foam Grip 2
38 Claw 1
39 Foam Pad Tube 2
40 Bolt, Button Head (M10 x 1.5 x 90mm) 1
41 Bolt, Button Head (M10 x 1.5 x 65mm) 4
42 Bolt, Button Head (M8 x 1.25 x 85mm) 1
43 Bolt, Button Head (M8 x 1.25 x 65mm) 2
44 Bolt, Button Head (M8 x 1.25 x 60mm) 2
45 Bolt, Button Head (M8 x 1.25 x 50mm) 4
46 Bolt, Button Head (M8 x 1.25 x 45mm) 4
47 Bolt, Button Head (M8 x 1.25 x 40mm) 2
PARTS LIST
19
48 Bolt, Button Head (M8 x 1.25 x 20mm) 4
49 Bolt, Round Head (M6 x 1 x 55mm) 1
50 Bolt, Round Head (M6 x 1 x 35mm) 2
51 Bolt, Round Head (M6 x 1 x 20mm) 12
52 Washer (M10) 11
53 Washer (M8) 18
54 Arc Washer (M8) 12
55 Washer (M6) 10
56 Arc Washer (M6) 4
57 Nylock Nut (M10 x 1.5) 5
58 Nylock Nut (M8 x 1.25) 13
59 Nylock Nut (M6 x 1) 3
60 Seat Belt 1
61 Bolt, Flat Head (M6 x 1 x 20mm) 1
62 Warning Label 1
63 Inversion Warning Decal 1
64 Combination Wrench 1
65 Allen Wrench (4mm) 1
66 Allen Wrench (5mm) 1
67 Allen Wrench (6mm) 1
68 Manual 1
PART# PART NAME QTY
PARTS LIST
20
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22

Sharper Image 55-1550 User manual

Sharper Image
Brand
Sharper Image
Model
55-1550
Category
Fitness, gymnastics & weight training
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents