Costar CDC2450MT Series Owner's manual

Costar
Brand
Costar
Model
CDC2450MT Series
Category
Security cameras
Type
Owner's manual
INSTRUCTION MANUAL
Please read this manual thoroughly before use and keep it handy for future reference.
22X PTZ III DOME CAMERA
II
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECTS THROUGH THE
VENTILATION GRILLS OR OTHER OPENINGS ON THE EQUIPMEMT.
CAUTION
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral is intended to alert the user
to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
III
FCC COMPLIANCE STATEMENT
CE COMPLIANCE STATEMENT
FCC INFORMATION: THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO
COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO
PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE
REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN
THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT. THIS
EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY
ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE
INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE TO RADIO
COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL
AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE
USER WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN
EXPENSE.
CAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY
THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER'S
AUTHORITY TO OPERATE THE EQUIPMENT.
THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.
CET APPAREIL NUMÉRIQUE DE LA CLASSE A EST CONFORME À LA NORME
NMB-003 DU CANADA.
WARNING
THIS IS A CLASS A PRODUCT. IN A DOMESTIC ENVIRONMENT THIS
PRODUCT MAY CAUSE RADIO INTERFERENCE IN WHICH CASE THE USER
MAY BE REQUIRED TO TAKE ADEQUATE MEASURES.
IV
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified
by the manufacturer, or sold with the apparatus. When a cart is
used, use caution when moving the cart/apparatus combination
to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused
for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been moisture, does not operate normally, or has been
dropped.
15. CAUTION – THESE SERVICING INSTRUCTIONS ARE FOR USE BY
QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF
ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN THAT
CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU QRE
QUALIFIED TO DO SO.
16. Use Certified/Listed Class 2 power source only.
17. Apparatus shall not be exposed to dripping or splashing and no object filled with
liquids, such as vases, shall be placed on the apparatus.
V
Table of Contents
Chapter 1 — Introduction ..........................................................................................................1
1.1 Features .............................................................................................................................................1
Chapter 2 — Installation and Configuration.........................................................................2
2.1 Package Contents............................................................................................................................2
2.2 Installation.........................................................................................................................................3
2.3 Basic Configuration of Dome Camera System........................................................................5
2.4 Setting Dome Camera Termination.............................................................................................6
2.5 Setting Dome Camera Address (ID)............................................................................................6
2.6 Setting Dome Camera Protocol and Video.............................................................................13
2.7 Connections....................................................................................................................................14
2.8 Getting Started...............................................................................................................................15
Chapter 3 — Program and Operation...................................................................................16
3.1 Dome Camera Selection ..............................................................................................................16
3.2 Accessing the On-Screen Menu Utility....................................................................................16
3.3 How to control the On-Screen Menu Utility............................................................................16
3.4 Auto Scan (Shortcut: SCAN).....................................................................................................17
3.5 Preset (Shortcut: PRST) .............................................................................................................19
3.6 Shortcut of Preset Program........................................................................................................21
3.7 Tour (Shortcut: TOUR) .................................................................................................................21
3.8 Pattern (Shortcut: PTRN).............................................................................................................22
3.9 Alarm.................................................................................................................................................23
3.10 Area Title........................................................................................................................................24
3.11 Privacy Zone.................................................................................................................................25
3.12 Camera Menu................................................................................................................................26
3.13 Dome Setup ..................................................................................................................................29
3.14 Function Run................................................................................................................................35
3.15 Factory Setup...............................................................................................................................36
Appendix A — Specifications.................................................................................................37
Appendix B — Troubleshooting ............................................................................................39
Appendix C — Glossary...........................................................................................................39
Appendix D — Short Cut Key .................................................................................................42
1
Chapter 1 — Introduction
1.1 Features
The dome camera and the keyboard controller make up the building blocks for any
surveillance/security system. Using multiple keyboard controllers and multiple dome cameras, no
place is too large for monitoring. Extensible and flexible architecture facilitates remote control
functions for a variety of external switching devices such as multiplexers and DVRs.
Built-in optical power zoom camera with True Night Shot function.
120 Preset positions with the individual Camera AE setup.
4 Tours consist of Presets, Patterns, Auto Scans and other Tours can be programmed with
over 150 functions and Preset locations. While moving, each Preset scan can be watched in
smooth Vector Scan mode.
4 Auto Scans with the normal, the vector, and the random mode and the Endless Auto-Pan
with 13 speed steps.
4 Patterns (up to 200 second) and 4 Privacy Zones.
8 Area Titles.
1 Alarm input / 1 Alarm output (TTL ON/OFF)
Variable speed from 0.1/sec to 380/sec.
Three Variable speed (SLOW, NORMAL, TURBO).
Turbo speed is 380/sec with Ctrl key pressed.
Pan / Tilt speed is inversely proportional to the zoom ratio with the option.
Maximum speed is 380/sec when Preset command.
Auto Calibration from 0.1 to 6 (Tilt range is 0 to 180).
Programmable user preferences (alarm, preset, title, etc.).
180 Digital Flip.
Up to 255 selectable camera addresses.
Multi-language Menu Display, Password Confirmation.
Function Run menu using DVR without function key (Pattern, Scan,..)
Built-in RS-485 receiver driver.
AC 24V or DC 12V for Dome.
Use Certified/Listed Class 2 power source only.
2
Chapter 2 — Installation and Configuration
2.1 Package Contents
The dome camera is design to a compact, small size, hard dome camera housing.
The housing is constructed of aluminum, steel and plastic. The housing is designed to be
mounted both wall and ceiling type.
The housing meets the Protection Classification IP66 standards for dust and moisture resistance.
* Dome Camera ................................................................1
* Instruction Manual (This Document) ...........................1
* Template sheet ..............................................................1
* Mounting bracket ..........................................................1
* Safety lanyard ...............................................................1
* Accessory kit .................................................................1
1) Mounting screws (PH6 x 35.0) ..........(4)
2) Plastic anchors ..................................(4)
3) O-Rings .............................................(4)
4) Torx wrench .......................................(1)
* Accessory connector ....................................................1
1) 2Pin Terminal Block ...........................(1)
2) 3Pin Terminal Block ...........................(1)
3) 4Pin Terminal Block ...........................(1)
3
2.2 Installation
The dome camera is for use in surface or pendent mounting applications and the mounting
member must be capable of supporting loads of up to 3.3lb (1.5kg). (Pendent mounting must use
pendent mount accessory.)
The dome camera’s mounting bracket should be attached to a structural object, such as hard
wood, wall stud or ceiling rafter that supports the weight of the dome camera.
CAUTION: A silicone rubber sealant must be applied to seal the housing to secure
waterproofing.
2.2.1 Locking Dome Camera
A. Make screw holes on the ceiling using the supplied mounting Template Sheet (Figure A).
B. Fix the Mounting Bracket using Anchors(4x) and Mounting Screws(4x) to the ceiling (Figure B).
C. Hook up the Safety Lanyard to the Safety Lanyard Hook of the Mounting Bracket (Figure C).
D. Align the locking tap on the bracket and the locking slot on the base of the dome (Figure D).
E. Turn the dome to the counterclockwise about 10 degree to the locked position (Figure E).
4
CAUTION 1: Before installing mounting bracket to surface pre-adjust the four mounting
screws "A" on the base of the dome camera to best match the mounting
bracket locked position. Unscrew the locking screw on the side of the dome's
base and fit the tab of the mounting bracket into the locking slot. Screws "A"
should not be too tight or too loose when the dome is in the locked position.
After setting the proper positions of screws "A" remove the mounting bracket
and install it to the proper surface. If it is too difficult to lock the dome in
position after the mounting bracket has been installed readjust the screws "A"
by unscrewing them a small amount and try to install dome camera again.
CAUTION 2: Set the termination and ID address of the dome before final installation as
described at 2.3 (figure 2) and 2.4.
5
2.3 Basic Configuration of Dome Camera System
Figure 1 – Basic Installation Diagram
The dome camera must be installed by qualified service personnel in accordance with all local
and federal electrical and building codes.
6
Figure 2 – Layout of DIP Switches
NOTE: Open the switch cover (position “a”) and change the setting of DIP switches.
The cover should be closed after setting DIP switches.
2.4 Setting Dome Camera Termination
The device which is connected at end of line, whether it is a dome camera or keyboard controller,
must have the cable for communication terminated by setting the appropriate DIP switch.
Without proper termination, there is potential for control signal errors. Total length of the cable for
communication should not exceed 4000ft (1.2km).
S3
Figure 3 – Setting Dome Camera Termination
2.5 Setting Dome Camera Address (ID)
To prevent damage, each dome camera must have a unique address (ID).
When installing multiple dome cameras using a multiplexer, it is suggested that the dome camera
address match the multiplexer port number.
The factory default setting is 1.
Refer to Figure 4.1 ~ 4.6 for setting the dome camera address (ID).
S3 D1
Terminated ON
Not terminated
OFF
7
Example: Port 1 = Dome 1, Port 2 = Dome 2 … Port 16 = Dome 16. If more than 16 dome
cameras are installed using two or more multiplexers, ID of the dome camera should be ID of
MUX x No. of camera IN. (e.g. multiplexer ID= n, Camera IN= m then ID of Dome =16x(n-1)+m )
S1
DOME ID
D1
(1)
D2
(2)
D3
(4)
D4
(8)
D5
(16)
D6
(32)
D7
(64)
D8
(128)
1
ON
OFF OFF OFF OFF OFF OFF OFF
2 OFF
ON
OFF OFF OFF OFF OFF OFF
3
ON ON
OFF OFF OFF OFF OFF OFF
4 OFF OFF
ON
OFF OFF OFF OFF OFF
5
ON
OFF
ON
OFF OFF OFF OFF OFF
6 OFF
ON ON
OFF OFF OFF OFF OFF
7
ON ON ON
OFF OFF OFF OFF OFF
8 OFF OFF OFF
ON
OFF OFF OFF OFF
9
ON
OFF OFF
ON
OFF OFF OFF OFF
10 OFF
ON
OFF
ON
OFF OFF OFF OFF
11
ON ON
OFF
ON
OFF OFF OFF OFF
12 OFF OFF
ON ON
OFF OFF OFF OFF
13
ON
OFF
ON ON
OFF OFF OFF OFF
14 OFF
ON ON ON
OFF OFF OFF OFF
15
ON ON ON ON
OFF OFF OFF OFF
16 OFF OFF OFF OFF
ON
OFF OFF OFF
17
ON
OFF OFF OFF
ON
OFF OFF OFF
18 OFF
ON
OFF OFF
ON
OFF OFF OFF
19
ON ON
OFF OFF
ON
OFF OFF OFF
20 OFF OFF
ON
OFF
ON
OFF OFF OFF
21
ON
OFF
ON
OFF
ON
OFF OFF OFF
22 OFF
ON ON
OFF
ON
OFF OFF OFF
23
ON ON ON
OFF
ON
OFF OFF OFF
24 OFF OFF OFF
ON ON
OFF OFF OFF
25
ON
OFF OFF
ON ON
OFF OFF OFF
26 OFF
ON
OFF
ON ON
OFF OFF OFF
27
ON ON
OFF
ON ON
OFF OFF OFF
28 OFF OFF
ON ON ON
OFF OFF OFF
29
ON
OFF
ON ON ON
OFF OFF OFF
30 OFF
ON ON ON ON
OFF OFF OFF
31
ON ON ON ON ON
OFF OFF OFF
32 OFF OFF OFF OFF OFF
ON
OFF OFF
33
ON
OFF OFF OFF OFF
ON
OFF OFF
34 OFF
ON
OFF OFF OFF
ON
OFF OFF
35
ON ON
OFF OFF OFF
ON
OFF OFF
Figure 4.1 – Setting Dome Camera Address (ID)
8
DOME ID
D1
(1)
D2
(2)
D3
(4)
D4
(8)
D5
(16)
D6
(32)
D7
(64)
D8
(128)
36 OFF OFF
ON
OFF OFF
ON
OFF OFF
37
ON
OFF
ON
OFF OFF
ON
OFF OFF
38 OFF
ON ON
OFF OFF
ON
OFF OFF
39
ON ON ON
OFF OFF
ON
OFF OFF
40 OFF OFF OFF
ON
OFF
ON
OFF OFF
41
ON
OFF OFF
ON
OFF
ON
OFF OFF
42 OFF
ON
OFF
ON
OFF
ON
OFF OFF
43
ON ON
OFF
ON
OFF
ON
OFF OFF
44 OFF OFF
ON ON
OFF
ON
OFF OFF
45
ON
OFF
ON ON
OFF
ON
OFF OFF
46 OFF
ON ON ON
OFF
ON
OFF OFF
47
ON ON ON ON
OFF
ON
OFF OFF
48 OFF OFF OFF OFF
ON ON
OFF OFF
49
ON
OFF OFF OFF
ON ON
OFF OFF
50 OFF
ON
OFF OFF
ON ON
OFF OFF
51
ON ON
OFF OFF
ON ON
OFF OFF
52 OFF OFF
ON
OFF
ON ON
OFF OFF
53
ON
OFF
ON
OFF
ON ON
OFF OFF
54 OFF
ON ON
OFF
ON ON
OFF OFF
55
ON ON ON
OFF
ON ON
OFF OFF
56 OFF OFF OFF
ON ON ON
OFF OFF
57
ON
OFF OFF
ON ON ON
OFF OFF
58 OFF
ON
OFF
ON ON ON
OFF OFF
59
ON ON
OFF
ON ON ON
OFF OFF
60 OFF OFF
ON ON ON ON
OFF OFF
61
ON
OFF
ON ON ON ON
OFF OFF
62 OFF
ON ON ON ON ON
OFF OFF
63
ON ON ON ON ON ON
OFF OFF
64 OFF OFF OFF OFF OFF OFF
ON
OFF
65
ON
OFF OFF OFF OFF OFF
ON
OFF
66 OFF
ON
OFF OFF OFF OFF
ON
OFF
67
ON ON
OFF OFF OFF OFF
ON
OFF
68 OFF OFF
ON
OFF OFF OFF
ON
OFF
69
ON
OFF
ON
OFF OFF OFF
ON
OFF
70 OFF
ON ON
OFF OFF OFF
ON
OFF
71
ON ON ON
OFF OFF OFF
ON
OFF
72 OFF OFF OFF
ON
OFF OFF
ON
OFF
73
ON
OFF OFF
ON
OFF OFF
ON
OFF
74 OFF
ON
OFF
ON
OFF OFF
ON
OFF
75
ON ON
OFF
ON
OFF OFF
ON
OFF
76 OFF OFF
ON ON
OFF OFF
ON
OFF
77
ON
OFF
ON ON
OFF OFF
ON
OFF
78 OFF
ON ON ON
OFF OFF
ON
OFF
79
ON ON ON ON
OFF OFF
ON
OFF
80 OFF OFF OFF OFF
ON
OFF
ON
OFF
Figure 4.2 – Setting Dome Camera Address (ID)
9
DOME ID
D1
(1)
D2
(2)
D3
(4)
D4
(8)
D5
(16)
D6
(32)
D7
(64)
D8
(128)
81
ON
OFF OFF OFF
ON
OFF
ON
OFF
82 OFF
ON
OFF OFF
ON
OFF
ON
OFF
83
ON ON
OFF OFF
ON
OFF
ON
OFF
84 OFF OFF
ON
OFF
ON
OFF
ON
OFF
85
ON
OFF
ON
OFF
ON
OFF
ON
OFF
86 OFF
ON ON
OFF
ON
OFF
ON
OFF
87
ON ON ON
OFF
ON
OFF
ON
OFF
88 OFF OFF OFF
ON ON
OFF
ON
OFF
89
ON
OFF OFF
ON ON
OFF
ON
OFF
90 OFF
ON
OFF
ON ON
OFF
ON
OFF
91
ON ON
OFF
ON ON
OFF
ON
OFF
92 OFF OFF
ON ON ON
OFF
ON
OFF
93
ON
OFF
ON ON ON
OFF
ON
OFF
94 OFF
ON ON ON ON
OFF
ON
OFF
95
ON ON ON ON ON
OFF
ON
OFF
96 OFF OFF OFF OFF OFF
ON ON
OFF
97
ON
OFF OFF OFF OFF
ON ON
OFF
98 OFF
ON
OFF OFF OFF
ON ON
OFF
99
ON ON
OFF OFF OFF
ON ON
OFF
100 OFF OFF
ON
OFF OFF
ON ON
OFF
101
ON
OFF
ON
OFF OFF
ON ON
OFF
102 OFF
ON ON
OFF OFF
ON ON
OFF
103
ON ON ON
OFF OFF
ON ON
OFF
104 OFF OFF OFF
ON
OFF
ON ON
OFF
105
ON
OFF OFF
ON
OFF
ON ON
OFF
106 OFF
ON
OFF
ON
OFF
ON ON
OFF
107
ON ON
OFF
ON
OFF
ON ON
OFF
108 OFF OFF
ON ON
OFF
ON ON
OFF
109
ON
OFF
ON ON
OFF
ON ON
OFF
110 OFF
ON ON ON
OFF
ON ON
OFF
111
ON ON ON ON
OFF
ON ON
OFF
112 OFF OFF OFF OFF
ON ON ON
OFF
113
ON
OFF OFF OFF
ON ON ON
OFF
114 OFF
ON
OFF OFF
ON ON ON
OFF
115
ON ON
OFF OFF
ON ON ON
OFF
116 OFF OFF
ON
OFF
ON ON ON
OFF
117
ON
OFF
ON
OFF
ON ON ON
OFF
118 OFF
ON ON
OFF
ON ON ON
OFF
119
ON ON ON
OFF
ON ON ON
OFF
120 OFF OFF OFF
ON ON ON ON
OFF
121
ON
OFF OFF
ON ON ON ON
OFF
122 OFF
ON
OFF
ON ON ON ON
OFF
123
ON ON
OFF
ON ON ON ON
OFF
124 OFF OFF
ON ON ON ON ON
OFF
125
ON
OFF
ON ON ON ON ON
OFF
Figure 4.3 – Setting Dome Camera Address (ID)
10
DOME ID
D1
(1)
D2
(2)
D3
(4)
D4
(8)
D5
(16)
D6
(32)
D7
(64)
D8
(128)
126 OFF
ON ON ON ON ON ON
OFF
127
ON ON ON ON ON ON ON
OFF
128 OFF OFF OFF OFF OFF OFF OFF
ON
129
ON
OFF OFF OFF OFF OFF OFF
ON
130 OFF
ON
OFF OFF OFF OFF OFF
ON
131
ON ON
OFF OFF OFF OFF OFF
ON
132 OFF OFF
ON
OFF OFF OFF OFF
ON
133
ON
OFF
ON
OFF OFF OFF OFF
ON
134 OFF
ON ON
OFF OFF OFF OFF
ON
135
ON ON ON
OFF OFF OFF OFF
ON
136 OFF OFF OFF
ON
OFF OFF OFF
ON
137
ON
OFF OFF
ON
OFF OFF OFF
ON
138 OFF
ON
OFF
ON
OFF OFF OFF
ON
139
ON ON
OFF
ON
OFF OFF OFF
ON
140 OFF OFF
ON ON
OFF OFF OFF
ON
141
ON
OFF
ON ON
OFF OFF OFF
ON
142 OFF
ON ON ON
OFF OFF OFF
ON
143
ON ON ON ON
OFF OFF OFF
ON
144 OFF OFF OFF OFF
ON
OFF OFF
ON
145
ON
OFF OFF OFF
ON
OFF OFF
ON
146 OFF
ON
OFF OFF
ON
OFF OFF
ON
147
ON ON
OFF OFF
ON
OFF OFF
ON
148 OFF OFF
ON
OFF
ON
OFF OFF
ON
149
ON
OFF
ON
OFF
ON
OFF OFF
ON
150 OFF
ON ON
OFF
ON
OFF OFF
ON
151
ON ON ON
OFF
ON
OFF OFF
ON
152 OFF OFF OFF
ON ON
OFF OFF
ON
153
ON
OFF OFF
ON ON
OFF OFF
ON
154 OFF
ON
OFF
ON ON
OFF OFF
ON
155
ON ON
OFF
ON ON
OFF OFF
ON
156 OFF OFF
ON ON ON
OFF OFF
ON
157
ON
OFF
ON ON ON
OFF OFF
ON
158 OFF
ON ON ON ON
OFF OFF
ON
159
ON ON ON ON ON
OFF OFF
ON
160 OFF OFF OFF OFF OFF
ON
OFF
ON
161
ON
OFF OFF OFF OFF
ON
OFF
ON
162 OFF
ON
OFF OFF OFF
ON
OFF
ON
163
ON ON
OFF OFF OFF
ON
OFF
ON
164 OFF OFF
ON
OFF OFF
ON
OFF
ON
165
ON
OFF
ON
OFF OFF
ON
OFF
ON
166 OFF
ON ON
OFF OFF
ON
OFF
ON
167
ON ON ON
OFF OFF
ON
OFF
ON
168 OFF OFF OFF
ON
OFF
ON
OFF
ON
169
ON
OFF OFF
ON
OFF
ON
OFF
ON
170 OFF
ON
OFF
ON
OFF
ON
OFF
ON
Figure 4.4 – Setting Dome Camera Address (ID)
11
DOME ID
D1
(1)
D2
(2)
D3
(4)
D4
(8)
D5
(16)
D6
(32)
D7
(64)
D8
(128)
171
ON ON
OFF
ON
OFF
ON
OFF
ON
172 OFF OFF
ON ON
OFF
ON
OFF
ON
173
ON
OFF
ON ON
OFF
ON
OFF
ON
174 OFF
ON ON ON
OFF
ON
OFF
ON
175
ON ON ON ON
OFF
ON
OFF
ON
176 OFF OFF OFF OFF
ON ON
OFF
ON
177
ON
OFF OFF OFF
ON ON
OFF
ON
178 OFF
ON
OFF OFF
ON ON
OFF
ON
179
ON ON
OFF OFF
ON ON
OFF
ON
180 OFF OFF
ON
OFF
ON ON
OFF
ON
181
ON
OFF
ON
OFF
ON ON
OFF
ON
182 OFF
ON ON
OFF
ON ON
OFF
ON
183
ON ON ON
OFF
ON ON
OFF
ON
184 OFF OFF OFF
ON ON ON
OFF
ON
185
ON
OFF OFF
ON ON ON
OFF
ON
186 OFF
ON
OFF
ON ON ON
OFF
ON
187
ON ON
OFF
ON ON ON
OFF
ON
188 OFF OFF
ON ON ON ON
OFF
ON
189
ON
OFF
ON ON ON ON
OFF
ON
190 OFF
ON ON ON ON ON
OFF
ON
191
ON ON ON ON ON ON
OFF
ON
192 OFF OFF OFF OFF OFF OFF
ON ON
193
ON
OFF OFF OFF OFF OFF
ON ON
194 OFF
ON
OFF OFF OFF OFF
ON ON
195
ON ON
OFF OFF OFF OFF
ON ON
196 OFF OFF
ON
OFF OFF OFF
ON ON
197
ON
OFF
ON
OFF OFF OFF
ON ON
198 OFF
ON ON
OFF OFF OFF
ON ON
199
ON ON ON
OFF OFF OFF
ON ON
200 OFF OFF OFF
ON
OFF OFF
ON ON
201
ON
OFF OFF
ON
OFF OFF
ON ON
202 OFF
ON
OFF
ON
OFF OFF
ON ON
203
ON ON
OFF
ON
OFF OFF
ON ON
204 OFF OFF
ON ON
OFF OFF
ON ON
205
ON
OFF
ON ON
OFF OFF
ON ON
206 OFF
ON ON ON
OFF OFF
ON ON
207
ON ON ON ON
OFF OFF
ON ON
208 OFF OFF OFF OFF
ON
OFF
ON ON
209
ON
OFF OFF OFF
ON
OFF
ON ON
210 OFF
ON
OFF OFF
ON
OFF
ON ON
211
ON ON
OFF OFF
ON
OFF
ON ON
212 OFF OFF
ON
OFF
ON
OFF
ON ON
213
ON
OFF
ON
OFF
ON
OFF
ON ON
214 OFF
ON ON
OFF
ON
OFF
ON ON
215
ON ON ON
OFF
ON
OFF
ON ON
Figure 4.5 – Setting Dome Camera Address (ID)
12
DOME ID
D1
(1)
D2
(2)
D3
(4)
D4
(8)
D5
(16)
D6
(32)
D7
(64)
D8
(128)
216 OFF OFF OFF
ON ON
OFF
ON ON
217
ON
OFF OFF
ON ON
OFF
ON ON
218 OFF
ON
OFF
ON ON
OFF
ON ON
219
ON ON
OFF
ON ON
OFF
ON ON
220 OFF OFF
ON ON ON
OFF
ON ON
221
ON
OFF
ON ON ON
OFF
ON ON
222 OFF
ON ON ON ON
OFF
ON ON
223
ON ON ON ON ON
OFF
ON ON
224 OFF OFF OFF OFF OFF
ON ON ON
225
ON
OFF OFF OFF OFF
ON ON ON
226 OFF
ON
OFF OFF OFF
ON ON ON
227
ON ON
OFF OFF OFF
ON ON ON
228 OFF OFF
ON
OFF OFF
ON ON ON
229
ON
OFF
ON
OFF OFF
ON ON ON
230 OFF
ON ON
OFF OFF
ON ON ON
231
ON ON ON
OFF OFF
ON ON ON
232 OFF OFF OFF
ON
OFF
ON ON ON
233
ON
OFF OFF
ON
OFF
ON ON ON
234 OFF
ON
OFF
ON
OFF
ON ON ON
235
ON ON
OFF
ON
OFF
ON ON ON
236 OFF OFF
ON ON
OFF
ON ON ON
237
ON
OFF
ON ON
OFF
ON ON ON
238 OFF
ON ON ON
OFF
ON ON ON
239
ON ON ON ON
OFF
ON ON ON
240 OFF OFF OFF OFF
ON ON ON ON
241
ON
OFF OFF OFF
ON ON ON ON
242 OFF
ON
OFF OFF
ON ON ON ON
243
ON ON
OFF OFF
ON ON ON ON
244 OFF OFF
ON
OFF
ON ON ON ON
245
ON
OFF
ON
OFF
ON ON ON ON
246 OFF
ON ON
OFF
ON ON ON ON
247
ON ON ON
OFF
ON ON ON ON
248 OFF OFF OFF
ON ON ON ON ON
249
ON
OFF OFF
ON ON ON ON ON
250 OFF
ON
OFF
ON ON ON ON ON
251
ON ON
OFF
ON ON ON ON ON
252 OFF OFF
ON ON ON ON ON ON
253
ON
OFF
ON ON ON ON ON ON
254 OFF
ON ON ON ON ON ON ON
255
ON ON ON ON ON ON ON ON
Figure 4.6 – Setting Dome Camera Address (ID)
13
2.6 Setting Dome Camera Protocol and Video
If a dome camera is to be installed with the keyboard controller, select the default protocol.
Consult service personnel if a dome camera is installed with device other than a keyboard
controller.
S2
You can set video type with dip switch.
Select video type with D1 in S2.
You can set Protocol with dip switch D2, D3 and D4 in S2.
S2
D2 D3 D4
PROTOCOL
OFF OFF OFF F2, F2E, Pelco-P, Pelco-D : default
OFF OFF
ON
F2, F2E
OFF
ON ON
Pelco-P, Pelco-D
You can set Baud Rate with dip switch D5 and D6 in S2.
S2
D5 D6
BAUD RATE
OFF OFF 2400 bps
OFF
ON
4800 bps
ON
OFF 9600 bps : default
ON ON
19200 bps
Figure 5 – Video type, Protocol, Baud rate Selection Switches
S2-D1 VIDEO TYPE
OFF NTSC
ON
PAL
14
2.7 Connections
• Connecting to the RS485
The dome camera can be controlled remotely by an external device or control system, such as a
control keyboard, using RS485 half-duplex serial communications signals.
• Connecting Video out connector
Connect the video out (BNC) connector to the monitor or video input.
• Connecting Alarms
AI (Alarm In)
You can use external devices to signal the dome camera to react on events. Mechanical or
electrical switches can be wired to the AI (Alarm In) and G (Ground) connectors.
See Chapter 3 — Program and Operation for configuring alarm input.
G (Ground)
NOTE: All the connectors marked G or GND are common.
Connect the ground side of the alarm input and/or alarm output to the G (Ground) connector.
AO (Alarm Output)
The dome camera can activate external devices such as buzzers or lights. Connect the device to
the AO (Alarm Out) and G (Ground) connectors.
See Chapter 3 — Program and Operation for configuring alarm output.
• Connecting the Power
Connect the power of AC 24V or DC 12V 1A for the dome camera.
When using a DC 12V adapter, connector the positive(+) pole to the ‘+’ position and the
negative(-) pole to the ‘-‘ position.
Use Certified/Listed Class 2 power source only.
15
2.8 Getting Started
Once installed apply power to the dome camera. The dome camera will start a configuration
sequence.
OSD Position
The dome can move the OSD position in the OSD position setup.
(AREA TITLE) (AF AE)
(FUNC TITLE )
(CTRL KEY TO MOVE)
SAVE AND EXIT(ESC TO CANCEL)
(ALARM MESSAGE) (DOME ID…)
(ANGLE…)
OSD Position Setup
001 AF AE
EMPTY DATA
DOMEID:0001
ALARM:1 W→360.0,090.0
INFORMATION
DISPLAY
FUNCTION
UNDER RUNNING
ALARM DISPLAY
CAMERA TITLE
CAMERA ID
VIEW DIRECTION
PAN & TILT ANGLE
PRESET TITLE
A
REA TITLE
STATUS of
FOCUS and AE
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

Costar CDC2450MT Series Owner's manual

Costar
Brand
Costar
Model
CDC2450MT Series
Category
Security cameras
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents