Aeg-Electrolux S70320-KA8 User manual

Page is loading ...

32 818 41 50-00/4

Dear customer,

Before placing your new refrigerator into operation please read these

operating instructions carefully. They contain important information

for safe use, for installation and for care of the appliance.

Please keep these operating instructions for future reference. Pass them

on to possible new owners of the appliance.

These operating instructions are for use with several technically

comparable models with varying accessories. Please observe the notes

which apply to your model.

1

Notes which are important for your safety or for the proper function-

ing of the appliance are stressed with a warning triangle and/or with

signal words (Warning!, Caution!, Important!). Please observe the fol-

lowing carefully.

0 1. This symbol and numbered instructions guide you step by step in the

operation of the appliance.

2. .....

3

Supplementary information regarding operation and practical uses of

the appliance appear after this symbol.

2

Tips and notes concerning economical and environmentally sound use

of the appliance are marked with the cloverleaf.

Explanations of the technical terminology used in the operating

instructions can be found at the end in the section "Technical

Terminology".

The operating instructions contain instructions for the correction of

possible malfunctions by the user in the section "Something not

working". If these instructions should not be sufficient, please contact

your local AEG Service Force Centre.

P

r

i

nte

d

on paper manu

f

acture

d

w

i

t

h

env

i

ronmenta

ll

y soun

d

processes.

he who thinks ecologically acts accordingly ...

818 41 50-00/4 33

Contents

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Environmental Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Appliance Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Installation Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

The Refrigerator needs Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Appliance Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Changing over the Door Hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Appliance Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

View of Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Buttons for Adjusting the Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Temperature display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

COOLMATIC-button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

ALARM OFF button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Prior to Initial Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Initial Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Temperature Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

"Open Door" Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Temperature warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Switching the Appliance off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Interior Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Storage Shelves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Variable Inner Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Bottle Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Bottle Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Contents

34 818 41 50-00/4

Opening the Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Correct Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Defrosting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

The Refrigerator is defrosted automatically . . . . . . . . . . . . . . . . . . . . . . . . 52

Cleaning and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Energy Saving Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

What to do if ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Correcting Malfunctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Replace Light Bulb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Noises during Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Regulations, Standards, Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Technical Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Customer Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

818 41 50-00/4 35

1 Important Safety Instructions

The safety aspects of our refrigerators comply with accepted technical

standards and the German Appliance Safety Law. Nevertheless, we con-

sider it our obligation to make you aware of the following safety infor-

mation:

Intended use

• The refrigerator is intended for use in the home. It is suitable for the

storing of food at low temperature. If the appliance is used for pur-

poses other than those intended or used incorrectly, no liability can

be accepted by the manufacturer for any damage that may be

caused.

• Alterations or changes to the refrigerator are not permitted for rea-

sons of safety.

• If you use the refrigerator in a commercial application or for pur-

poses other than the cooling of foods, please observe all valid legal

regulations for your application.

Prior to initial start–up

• Check the refrigerator for transport damage. Under no circumstance

should a damaged appliance be plugged in! In the event of damage,

please contact your retailer.

• Make sure that the power plug is not squashed or damaged by the

back of the appliance. A damaged power plug may overheat and

cause a fire.

• If the power plug socket is loose, do not insert the power plug. There

is a risk of electric shock or fire.

Refrigerant

The refrigerant isobutane (R600a) is contained within the refrigerant

circuit of the appliance, a natural gas with a high level of environmen-

tal compatibility, which is nevertheless flammable.

• Warning - During transportation and installation of the appliance,

be certain that none of the components of the refrigerant circuit

become damaged.

• If the refrigerant circuit should become damaged:

– avoid open flames and sources of ignition;

– thoroughly ventilate the room in which the appliance is situated.

Important Safety Instructions

36 818 41 50-00/4

Safety of children

• Packaging (e.g. wraps, polystyrene) can be dangerous for children.

There is a risk of suffocation! Keep packaging material away from

children!

• Please make old appliances unusable prior to disposal. Pull out the

mains plug, cut off the mains cable, break or remove spring or bolt

catches, if fitted. By doing this you ensure that children cannot lock

themselves in the fridge when playing (there is risk of suffocation!) or

get themselves into other dangerous situations.

• Often children cannot recognise the hazards present in household

appliances. It is therefore important that you ensure adequate super-

vision and never let children play with the appliance!

Daily Operation

• Containers with flammable gases or liquids can leak at low tempera-

tures. There is a risk of an explosion! Do not store any containers with

flammable materials such as, for example, spray cans, fire extin-

guisher refill cartridges etc in the refrigerator.

• Warning - Do not operate any electrical appliances in the refrigera-

tor (e.g. electric ice cream makers, mixers etc.) unless they have been

authorised by the manufacturer.

• Warning - In order not to impair the function of the appliance, never

cover or obstruct the ventilation openings.

• Warning - Do not use any mechanical devices or other artificial

means to speed up defrosting unless they are recommended by the

manufacturer.

• Before cleaning the appliance, always switch off the appliance and

unplug it, or pull the house fuse or switch off the circuit breaker.

• Do not remove the power cord by pulling on its lead, particularly

when the appliance is being pulled out of its niche. Damage to the

cord may cause a short circuit, fire and/or electric shock.

• Do not place heavy articles or the appliance itself on the power cord.

There is a risk of a short circuit and fire.

• If the power cord is damaged, it must be replaced by a certified

service agent or qualified personnel.

In case of malfunction

• If the a malfunction occurs on the appliance, please look first in the

"What to do if ..." section of these instructions. If the information

given there does not help, please do not perform any further repairs

yourself.

818 41 50-00/4 37

• Refrigerators may only be repaired by qualified service engineers.

Improper repairs can give rise to significant hazards. If your appliance

needs repairing, please contact your local AEG Service Force Centre.

Environmental Information

2

Packaging material

The packaging materials are environmentally friendly and can be recy-

cled. The plastic components are identified by markings, e.g. >PE<,

>PS<, etc. Please dispose of the packaging materials in the appropriate

container at the community waste disposal facilities.

2 Old appliance

The symbol

W on the product or on its packaging indicates that this

product may not be treated as household waste. Instead it shall be

handed over to the applicable collection point for the recycling of elec-

trical and electronic equipment. By ensuring this product is disposed of

correctly, you will help prevent potential negative consequences for the

environment and human health, which could otherwise be caused by

inappropriate waste handling of this product. For more detailed infor-

mation about recycling of this product, please contact your local city

office, your household waste disposal service or the shop where you

purchased the product.

1

Warning! Before disposing of old appliances make them inoperable.

Remove plug from mains, sever the power cable, remove or destroy any

snap or latch closures. This eliminates the danger that playing children

lock themselves into the appliance (danger of suffocation!) or place

themselves into other life-endangering situations.

When disposing of your old appliance:

• The appliance may not be disposed of with domestic waste or bulky

refuse.

• The refrigerant circuit, especially the heat exchanger at the back of

the appliance, may not be damaged.

• Information concerning collection schedules or locations can be

obtained from the local disposal authorities or town hall.

38 818 41 50-00/4

Appliance Transport

Two persons are required for transport of the appliance. There are two

recessed handles at the front of the base and at the back of the

appliance at the top for improved gripping.

0 1. Grip the appliance with the recessed handles positioned as in the draw-

ing, and transport the appliance.

2. In order to push the appliance into its final position, press carefully at

the top of the door and tip the appliance back slightly. The weight is

thus transferred to the back wheels and the appliance can be easily

pushed.

Before Use

Packaging

0 1. Remove all adhesive tape and packaging from the interior of the appli-

ance.

3

Any remnants of adhesive can be removed with white spirit.

2. Remove the transport protection pieces and pull off the adhesive tape.

818 41 50-00/4 39

Remove the transport fittings from the storage shelves:

3. Slide the fittings securing the shelf

forward to the thicker section on

the edge of the storage shelf.

4. Slide the storage shelf far enough

forward so that it can be hinged

downwards and the fittings can be

removed from the guides.

5. Wash the inside of the appliance

with lukewarm water with a little

bicarbonate of soda added (5 ml to

0.5 litre of water). Do not use soap

or detergent as the smell may lin-

ger. Dry the appliance thoroughly.

Installation

Installation Location

The appliance should be installed in a well ventilated, dry room.

Energy use and efficient performance of the appliance is affected by

the ambient temperature.

The appliance should therefore

– not be exposed to direct sunlight;

– not be installed next to radiators, cookers or other sources of heat;

– only be installed at a location whose ambient temperature

corresponds to the climate classification, for which the appliance is

designed.

The climate classification can be found on the rating plate, which is

located at the left on the inside of the appliance.

The following table shows which ambient temperature is correct for

each climate classification:

Climate classification for an ambient temperature of

SN +10 to +32 °C

N +16 to +32 °C

ST +18 to +38 °C

T +18 to +43 °C

Installation

40 818 41 50-00/4

If installation next to a source of heat is unavoidable, the following

minimum clearances must be maintained at the sides of the appliance:

– for electric cookers 3 cm;

– for oil and coal fired ranges 30 cm.

If these clearances cannot be maintained a heat insulating pad is

required between the cooker and the refrigeration appliance.

The Refrigerator needs Ventilation

Air is fed under the door through the

vent slots in the base and is exhausted

upwards along the back wall. To ensure

proper air circulation never cover or alter

the vent openings.

Important! If the appliance is installed

under a hanging cabinet, a clearance of

at least 10 cm between the top of the

appliance and the cabinet above it must

be maintained.

Please check whether, after installing

your appliance and especially after

rehingeing the door, the door seal seals right round. An untight door

seal may lead to heavy frosting and a higher power consumption (see

also "Something not working“).

Appliance Alignment

0 1. The appliance level please compensate for unevenness in the floor by

turning the two adjustable feet at the front.

2. When two appliances are placed beside each other, the distances

enclosed in the plastic wrapping should be glued between the appli-

ances as shown in the illustration.

Installation

818 41 50-00/4 41

.

Electrical Connection

A properly installed socket outlet with earthing contact is required for

electrical connection. Electrical fuse protection must be of at least 10

ampere.

If the outlet socket is no longer accessible after installation of the

appliance, appropriate measures must be taken during electrical instal-

lation to assure that the appliance can be disconnected from the mains

(e.g. fuse, circuit breaker, non-operate current safety-switch or the like,

with a contact opening of at least 3 mm).

0 1. Before initial start-up, refer to the appliance rating plate to ascertain if

supply voltage and current values correspond with those of the mains

at the installation location.

e.g.: AC 220 ... 240 V 50 Hz or

220 ... 240 V~50 Hz

(i.e. 220 to 240 volts alternating current, 50 Hertz)

The rating plate is inside the appliance at the left.

Warning: To avoid potential danger, if the mains connection lead of

this appliance is damaged, it must be replaced by our customer service

representative or a person with similar qualifications.

Warning: Under no circumstances should the appliance be connected

to electronic “power saving plugs” or to a.c.-d.c. converters which con-

vert direct current to 230 V alternating current (e.g., solar installations,

ship networks)

42 818 41 50-00/4

Changing over the Door Hinges

The door hinges can be changed from right (as supplied) to left if

required to suit the location where the appliance is installed.

1

Warning! Unplug from the mains, before reversing the door.

0 1. Open the door and remove the

plinth to the front. Move the

door bearing cover on the plinth

from the left to the right.

Close the door

2. With the door closed, remove

the cross-head screws from the

lower door bearing and remove

the door bearing downwards.

3. Remove the door fitting from the

door bearing (1, 2). Move the

bearing pivot from the right to

the left hand hole (3). Place the

door fitting supplied on the bear-

ing pivot (4, 5).

1

2

5

4

3

Changing over the Door Hinges

818 41 50-00/4 43

4. Unscrew Phillips screw from the

door bottom right and remove

door fitting (1). Insert door fitting

supplied in the door bottom left

and fasten with Phillips screw (2).

Carefully remove the door to the

front and place on one side.

5. Move the upper bearing pivot to

the left.

6. Carefully slide the door onto the

top bearing pivot and close.

7. Place the lower door bearing with

the bearing pivot in the lower left

of the door and fasten.

8. Move the door handle from the

left to the right and cover the

remaining holes with the hole

cover pins.

9. Open the door and fit the plinth.

44 818 41 50-00/4

Appliance Description

View of Appliance

(various models)

á Control panel

à Butter and cheese compartment with lid

â Door storage compartments

ä Variable storage box

ã Bottle compartment

å Fruit and vegetable drawer

ç Shelves

é Bottle rack

è Rating plate

Appliance Description

818 41 50-00/4 45

Control Panel

1 ON/OFF button and stand-by display (green)

2 Temperature display

3 Temperature setting buttons

4 COOLMATIC button and COOLMATIC indicator light (yellow)

5 ALARM OFF button and warning indicator light (red)

Buttons for Adjusting the Temperature

The temperature is adjusted using the

„+“ (WARMER) and „-“ (COLDER) buttons.

These buttons are connected to the temperature display.

• The temperature display is switched over from the display of the

ACTUAL temperature (Temperature display is illuminated) to the dis-

play of the DESIRED temperature (Temperature display flashes) by

pressing one of the two buttons, „+“ (WARMER) or „-“ (COLDER).

• Each time one of the two buttons is pressed again the DESIRED tem-

perature is adjusted by 1 °C.

• If neither button is pressed, the temperature display automatically

switches back after a short period (approx. 5 sec.) to the display of

the ACTUAL temperature. The ACTUAL temperature in the appliance is

now adjusted to match the preset DESIRED temperature.

DESIRED temperature means:

The temperature that is required in the appliance, this can be adjusted

to the temperatures shown in the display. The DESIRED temperature is

indicated by flashing numbers.

ACTUAL temperature means:

The temperature display indicates the temperature that is currently

present in the appliance. The ACTUAL temperature is indicated with

illuminated numbers.

3

Once the COOLMATIC function has been switched on the DESIRED tem-

perature that was set originally cannot be changed.

Appliance Description

46 818 41 50-00/4

Temperature display

The temperature display shows several types of

information.

• In normal operation the current fridge compartment temperature is

displayed (ACTUAL temperature).

• During temperature adjustment, a blinking display of the

temperature selected at the moment occurs (DESIRED temperature).

• If there is a fault in the appliance a square or a letter will appear in

the temperature display.

COOLMATIC-button

The COOLMATIC function is suited for quick cooling of

large quantities of goods in the refrigerator, e.g. drinks and

salads for a party.

0 1. The COOLMATIC function is switched on by pressing the COOLMATIC

button. The yellow light illuminates. The compressor runs continuously.

The COOLMATIC function now provides for intensive cooling. A DESI-

RED temperature of +2 °C is automatically selected. The COOLMATIC

function is ended automatically after a period of 6 hours. The originally

selected DESIRED temperature is again valid. The temperature display

shows the ACTUAL refrigerator temperature.

2. The COOLMATIC function can be ended manually at any time by press-

ing the COOLMATIC button again. The yellow light goes out.

Important! Once the COOLMATIC function has been switched on the

DESIRED temperature that was set originally cannot be changed.

ALARM OFF button

With the ALARM OFF button, the acoustic warning signal

can be switched off, e.g. the "Open Door" warning when

sorting in or out, the food to be chilled.

818 41 50-00/4 47

Prior to Initial Start-Up

1

Before connecting the appliance to the mains and putting it into ope-

ration for the first time, leave the appliance to stand for 30 minutes if

was transported upright. After transport on its side, the appliance must

be left to stand for 4 hours before putting it into operation. This is

necessary to allow the oil to flow back into the compressor. Otherwise

the compressor may be damaged.

0 1. Please clean the appliance interior and all accessories prior to initial

start-up (see section: "Maintenance and Cleaning").

2. The appliance must be correctly installed in accordance with the chap-

ter "Installation" before it is put into operation for the first time. Care

should be especially taken that the mains voltage and frequency avail-

able correspond with the appliance’s rating plate.

Initial Start-Up

0 1. Insert plug into mains socket.

2. Press ON/OFF button.

A warning tone sounds and the red warning light flashes indicating

that the required storage temperature has not yet been reached. The

compressor starts and then runs automatically.

3. Press the ALARM OFF button to switch off the warning tone.

4. Set temperature to +5 °C or colder (see section: "Temperature Adjust-

ment").

3

Goods to be refrigerated can be loaded immediately after switching on,

because the storage temperature in the refrigerator is quickly reached.

48 818 41 50-00/4

Temperature Adjustment

With the buttons for temperature adjustment the desired temperatures

in the refrigerator can be adjusted.

0 1. Press either the „+“ (WARMER) or „-“ (COLDER) button.

The temperature display switches over and the DESIRED temperature

currently set flashes on the temperature display.

2. To adjust to a warmer temperature, press the „+“ (WARMER) button. To

adjust to a colder temperature, press the „-“ (COLDER) button. The

changed setting is immediately displayed on the temperature display.

• Each time one of the two buttons is pressed again the DESIRED tem-

perature is adjusted by 1 °C.

The following DESIRED temperature settings are possible:

from +2 °C up to +8 °C in 1 °C steps;

Note: From a food science point of view, +5 °C for the refrigerator

compartment should be considered cold enough as a storage

temperature.

3

When the buttons are not further pressed after an adjustment has been

made, after a short period (approx. 5 sec.) the temperature display swit-

ches over and again displays the ACTUAL temperature in the refrigera-

tor. The display changes from flashing to illuminated numbers.

Important! Please check red warning display and temperature display

regularly to ensure maintenance of the storage temperature.

"Open Door" Warning

If the fridge door is left open for longer than 5 minutes the red warn-

ing display will flash and an acoustic warning tone will sound.

If you need more time to load or rearrange refrigerated foods, you can

switch off the warning tone by pressing the ALARM OFF button.

The red warning display will go off when the door is closed.

818 41 50-00/4 49

Temperature warning

The red warning light flashes and a warning tone sounds, as soon as the

temperature in the refrigerator is warmer than 12 °C. Such a rise in

temperature can possibly be put down to:

– opening the door a lot or leaving it open for a long time;

– storing larger quantities of warm food;

– a fault with the appliance.

You can turn off the warning tone using the ALARM OFF button.

The warning light and the warning tone switch off automatically,

when the ACTUAL temperature existing in the refrigerator drops below

12 °C again.

Switching the Appliance off

In order to protect chilled goods, the appliance is guarded against

accidental switching off (child-proof).

0 1. To switch off press and hold the ON/OFF button for approximately 1

second. Illumination at the temperature display goes off.

3

The appliance is only completely disconnected from the electricity

supply when the power plug has been removed from the power outlet.

Note:

The appliance cannot be switched on or off if unplugged, or if there is

no power being supplied to it.

Following connection to the mains power supply, the appliance returns

to the same operating state as before the interruption of main power.

If the appliance is not going to be used for an extended period:

0 1. Switch appliance off by pressing and holding the ON/OFF button for

approximately 1 second.

2. Unplug or switch off at the mains supply.

3. Clean thoroughly (see section: "Maintenance and Cleaning").

4. Leave door open to avoid accumulation of odours.

50 818 41 50-00/4

Interior Accessories

Storage Shelves

0 1. A storage shelf must be inserted into the lower guide track above the

fruit and vegetable trays. It must always remain in this position, so that

fruits and vegetables remain fresh longer.

The remaining storage shelves can

be adjusted to various heights:

0 1. Pull the storage shelf forward until

it can be tipped up or down and

removed.

2. To insert at a different height use

the same procedure in reverse.

Adjustment for tall items:

0 1. Remove the front half of the two-

part vario glass storage shelf and

insert it at a different level. Space is

then gained for storage of tall items

on the storage shelf below.

Variable Inner Door

The door compartments can be pulled up and removed, and inserted at

other positions as needed.

Bottle Rack

Place bottles in the rack with the

bottleneck to the front.

Important: Only store unopened

bottles horizontally.

The bottle rack can be tilted for

storing opened bottles.

818 41 50-00/4 51

0 1. To do this pull the bottle rack for-

ward until it can be tilted

upwards, then slide the front sup-

port into the next level up.

Bottle Holder

Some models are equipped with a

bottle holder in the bottle compart-

ment. This is used to prevent

individual bottles from falling over

and can be slid sideways.

Opening the Door

If the door is closed when the appliance is in operation, it cannot be

immediately opened again, because a vacuum occurs which holds the

door closed until pressure has been equalised. The door can be opened

again after several minutes.

If your appliance is equipped with a

QUICK door opener - an opening

mechanism integrated into the door

handle - the door can be opened

easily at any time.

Page is loading ...

Aeg-Electrolux S70320-KA8 User manual

Aeg-Electrolux S70320-KA8 User manual

in other languages

Related papers

Other documents