Agria 5300 Owner's manual

Brand: Agria

Model: 5300

Category: Lawnmowers

Type: Owner's manual

Translation of the original Operating In-

structions

Meadow mower

agria 5300

Petrol engine: Honda

5300 535

Before commissioning please read the operating instructions

and note the safety and warning information!

Operating Instructions No. 998 478GB 02.20

agria 5300

Nameplate

Please enter here:

Machine art. no.: .............................................................

ID/machine no.: ..............................................................

Engine type: ...................................................................

Engine no.: .....................................................................

Date of purchase: ...........................................................

For nameplate see page 51, Fig. A/7

Petrol engine: Engine no. see page 51, Fig. B/6

Please provide this information for each spare parts order,

to prevent errors in delivery.

Only use genuine Agria spare parts!

The technical data, illustrations and dimensions provided in

these operating instructions are non-binding. No claims may

be derived from them. We reserve the right to make im-

provements without amending this manual.

Scope of delivery

(please check):

• Meadow mower - base unit

• Handlebar with grip screw

• 1 pair driving wheels*

• Cutter bar*

• Tool kit

• Original Operating Instructions

• Original engine operating instructions

• Machine identity card

(in envelope on outside of box)

Please complete the machine identity card and

re-turn it to Agria-Werke.

* = corresponding to the machine version

Meadow mower agria 5300

Symbols

Warning symbol, refer-

ence to danger point

Important information

Fuel

Choke

Engine

Engine start

Engine speed

Engine stop

Air filter

Engine oil level

Clutch

Mower drive

Wheel drive

forward

reverse

Fast

Slow

Closed (locked)

Open (unlocked)

Visual inspection

Attachment point for re-

covery, lashing, towing

Wear protective gloves

Wear safety shoes

Fan cooling

Oil lubrication point

Grease lubrication point

Maintenance interval

Before each start-up

After each cleaning (in

particularly with a high-

pressure cleaner)

Annually

See separate engine op-

erating instructions

- agria-Service - = contact your agria

service centre

agria 5300

Designation of parts

Meadow mower agria 5300

Fig. A

1 Cutter bar

2 Cutter bar gliding soles

3 Knife driver

4 Lubricating nipple for beam

supporting pin

5 Lubricating nipple for crank

roller

6 Mowing unit hood

7 Nameplate / ID no.

8 Engine

10 Handlebars

11 Belt guard, V-belt clutch

12 Cutter bar linkage

Lubricating nipple for cutter

bar linkage

14 Gearbox oil filler plug /

check plug

15 Gearbox cover /

gearbox oil drain hole

16 Driving wheel

17 Catch spring for driving wheel

Fig. B

1 Air filter

2 Carburettor

3 Fuel tank cap

4 Fuel tank

5 Choke lever

6 Engine type no.

7 Starter handle

8 Fan grille

9 Exhaust with contact guard

10 Sparking plug, sparking-plug

connector

11 Oil dipstick

12 Engine oil drain plug

13 Fuel cock

14 Engine stop switch

Meadow mower agria 5300

Contents

Nameplate .................................................................................................... 2

Scope of delivery .......................................................................................... 2

Symbols ............................................................................................... 3

Designation of parts ........................................................................... 4

Unpacking and assembly instructions ............................................. 8

1 Safety Instructions ........................................................................ 9

Intended use ................................................................................................. 9

2 Technical Data ............................................................................. 15

Machine ...................................................................................................... 15

Petrol engine .............................................................................................. 17

3 Devices and Operating Elements ............................................... 18

Engine ........................................................................................................ 18

Speed regulating lever................................................................................ 19

Safety circuit ............................................................................................... 19

Engine stop switch...................................................................................... 20

Traction drive .............................................................................................. 20

Clutch ......................................................................................................... 21

Wheel drive ................................................................................................ 21

Mower drive ................................................................................................ 22

Steering bar ................................................................................................ 22

Driving wheels ............................................................................................ 23

Cutter bar .................................................................................................... 25

Attachment points ....................................................................................... 26

4 Commissioning and Operation .................................................. 27

Commissioning ........................................................................................... 27

Before starting the engine .......................................................................... 29

Danger zone ............................................................................................... 30

Starting the petrol engine ........................................................................... 31

Stopping the petrol engine .......................................................................... 32

Mowing ....................................................................................................... 33

Mowing on slopes ....................................................................................... 35

Safety instructions for handling .................................................................. 37

5 Maintenance and Repair ............................................................. 38

Petrol engine .............................................................................................. 39

Meadow mower agria 5300

Machine ...................................................................................................... 42

Labels ......................................................................................................... 51

General ....................................................................................................... 52

Cleaning ..................................................................................................... 52

Storage ....................................................................................................... 53

6 Troubleshooting and Remedies ................................................. 54

Petrol engine .............................................................................................. 54

Machine ...................................................................................................... 56

7 Decommissioning / Disposal ...................................................... 58

Inspection and Maintenance Overview........................................... 60

Electric diagram of petrol engine .................................................... 62

Lubrication plan ................................................................................ 63

Paints, Wear parts............................................................................. 64

Declaration of Conformity ................................................................ 65

Designation of parts.................................................................................... 66

Meadow mower agria 5300

Unpacking and assembly instructions

Unpacking

Open the top lid of the

cardboard box. Cut the

cardboard box at all four edges, and fold down

the cardboard walls.

ckaging should be recycled in an environmen-

tally friendly manner.

Assembly

Fold up the handlebar

• Unscrew and remove hexagon head screw (3) and hexagon nut (4)

• Swing up the steering bar (2). Insert the hexagon head screw (3) through the

bores. Install and tighten the hexagon nut (4).

Pull the hand lever for wheel switching (6) to position "0" and let it engage. The

wheel drive is now switched off and the machine can be moved without motor drive.

Pull the machine rearwards out of the cardboard box

Attach the cutter bar (5). See page 25

Carry out the steps for initial startup. See page 27.

Safety Instructions

Meadow mower agria 5300

1 Safety Instructions

Before commissioning, please read the

operating instructions and note:

Warning

symbol

This symbol has been used throughout

these operating instructions to highlight

all sections relevant to your safety. Also

pass on all safety instructions to other

users.

Intended use

The machine meets the current state of

the art and complies with the applicable

safety regulations at the time of market-

ing within the context of the approved

use. In terms of design it was not possi-

ble to eliminate either the foreseeable

misuse or the remaining risk without

limiting the functionality in accordance

with the regulations.

The agria 5300 meadow mower is

a manually guided, self-propelled, sin-

gle-axle machine which can be com-

bined with mower heads and accesso-

ries that are approved in the Agria sales

list. The meadow mower is designed

exclusively for cutting grass and similar

plants and thin, non-woody undergrowth

in agriculture and forestry as well as for

the maintenance of green areas and

parks. After attaching the clearing blade,

which is also included in the Agria sales

list, it may also be used as a snow clear-

ing machine (intended use).

Any other use is considered to be con-

trary to the intended purpose. The man-

ufacturer is not liable for any damages

resulting from such use and the risk is

entirely the user's own.

Intended use also includes observance

of the operating, servicing and mainte-

nance conditions stipulated by the man-

ufacturer.

Unauthorized changes to the machine,

especially to the safety equipment, may

lead to increased levels of danger, which

would rule out any manufacturer liability

for resulting damage.

When using the machine on public roads

– and when being transported – the

national road traffic regulations of the

relevant country must be complied with

(marking, lighting, etc.).

ATTENTION: Never use the machine on

public roads with a trailer. The approval

requirements are not fulfilled.

A trailer for operation with the two-wheel

tractor is not included in the Agria sales

program. An expertise to obtain an indi-

vidual homologation (to German §21

StVZO) for the two-wheel tractor is not

available from the manufacturer.

Any unauthorized combination of the

two-wheel tractor with a trailer excludes

any liability of Agria.

The machine is intended to be used in

commercial and in private applications.

The machine must be operated as di-

rected in the operating instructions.

Other operators must given instruction if

required.

Any improper use or execution of activi-

ties of the machine not described in

these instructions constitutes unauthor-

ized misuse and is not within the statuto-

ry limits for liability of the manufacturer.

Improper use of the machine can en-

danger people and may result in dam-

age to the machine or other property of

the operator. It can also impair the func-

tionality of the machine.

Reasonable foreseeable misuse

Foreseeable misuse and improper han-

dling include inter alia:

• Removal or manipulation of protec-

tive and safety devices

Safety Instructions

Meadow mower agria 5300

• Using not approved mower heads or

clearing blades

• Working on steep slopes without

securing the operator, the machine

and the working area

• Transport and manoeuvring move-

ments with activated knife drive

• Failure to observe maintenance

intervals

• Omitting measurements and tests

for the early detection of damage

• Failure to replace wearing parts

• Incorrectly executed maintenance or

repair work

• Improper use.

General safety and accident

prevention regulations

Basic rule:

Please observe the relevant accident

prevention regulations as well as the

generally recognized rules pertaining to

safety, occupational health and traffic

laws.

The use of public transportation routes is

subject to the Road Traffic Act in its

latest version.

Please check the traffic and operating

safety of the machine before each com-

missioning!

The machine may only be used, ser-

viced and repaired by persons who are

familiar with it and have been instructed

in the hazards involved.

Persons under the age of 16 must not

operate the machine!

Only work with good visibility and in

good lighting conditions.

Operator clothing must fit tightly. Wear

sturdy footwear.

The affixed warning and information

signs provide important information for

safe operation; please observe them for

your own safety!

The engine must be switched off for

transport on motor vehicles or trailers

outside the working area.

Be careful with rotating tools - keep a

safe distance!

Be careful with coasting tools. Before

you start working on them, wait until they

have come to a complete stop!

There is a risk of crushing and shearing

on power-operated parts!

Riding on the implement during opera-

tion is not permitted.

Driving behaviour, steering – and possi-

bly – braking capability and tipping be-

haviour are influenced by attached or

suspended devices and loads. Therefore

ensure adequate steering and braking

capability.

Match the operating speed to the condi-

tions.

Do not adjust the setting of the engine

speed governor. A high speed increases

the risk of accidents.

Working area and danger zone

The working area is the entire area to be

worked on. The user is responsible for

third parties in the working area.

Staying in the danger zone of the ma-

chine is not permitted (see page 30).

Check the work area before starting and

moving. Pay special attention to children

and animals.

Foreign objects are to be removed from

the area to be worked on prior to starting

work. Look out for additional foreign

objects while working and remove these

promptly.

For operation in enclosed areas, ensure

that a safety distance is kept from edges

to prevent damage to tools.

Safety Instructions

Meadow mower agria 5300

Operation and protective de-

vices

Before you start work

Familiarize yourself with the equipment

and operating elements and their func-

tions. Above all, learn how to turn the

engine off quickly and safely in an

emergency!

Ensure that all protective devices are

mounted and properly adjusted!

If no add-on device is attached, the PTO

shaft must be switched off and covered

with the protective cap.

Suitable shoes must be worn depending

on the type of ground surface (vegeta-

tion, humidity ...), so that the operator

does not slip or fall.

Startup

Do not start the engine in closed rooms,

the exhaust fumes contain carbon mon-

oxide, which is very toxic if inhaled!

Before starting the engine, set all operat-

ing elements to neutral or idle position.

Do not step in front of the machine or

the add-on device to start the engine.

Operation

Never leave the operator's position at

the steering bar while working.

Never adjust operator bars while work is

in progress – risk of accident!

For all work with the device, especially

when turning, the machine operator

must maintain the distance from the

device shown by the bars.

Riding on the implement during opera-

tion or in transport is not permitted.

In the event of any clogging to the work

equipment or add-on device, the engine

must be stopped and the work equip-

ment or add-on device must be cleaned

with appropriate tools. There may be

tension in the drive train as a result of

the blockage, which is why you should

resolve the blockage carefully.

In the event of any damage to the ma-

chine or the add-on device, shut down

the engine immediately and have the

damage repaired.

In the event of any malfunctions to the

steering, stop and park the machine

immediately. Have the fault resolved

without delay.

If there is a risk of skidding down on

sloping terrain, then the machine must

be held by an attendant using a bar or a

rope. The attendant must be located

above the machine at a safe distance

from the work equipment.

Work across the slope along contour

lines if possible. If possible, turn the

machine in uphill direction.

Finishing work

Never leave the machine unsupervised

while the engine is running.

Switch the engine off before leaving the

machine. Then close the fuel tap(s) (if

present).

Take care not to park the hot machine in

the blazing sun.

Protect the machine against unauthor-

ized use. In ignition key models, remove

the ignition key; otherwise, remove the

spark plug connector.

Implements

Attach an implement only when engine

and implement drive are switched off.

Prior to attaching and starting the im-

plement, read and observe the operating

instructions of the implement.

Use adequate tools and wear gloves to

replace implements and parts thereof.

Put the supporting equipment to the

proper position and ensure stability

when you attach or remove an imple-

ment.

Secure machine and implements against

rolling away (parking brake - if installed,

wheel chocks).

Safety Instructions

Meadow mower agria 5300

There is a risk of injuries when you at-

tach an implement. Take special care.

Attach an implement in accordance with

the regulations and only at the specified

fixtures.

Always switch off the working tools dur-

ing a transport ride or when you drive to

adjacent working areas.

Secure machine and implement against

unauthorized use and rolling away when

you leave it. If necessary, install

transport or safety equipment, and put it

in protective position.

Mowing equipment

When handled improperly, the sharp

edges of the mower knives can cause

significant injuries. Always wear protec-

tive gloves when you work on the

knives.

Ensure that the screwing movements

are away from the cutting edges when

you replace a knife and loosen or secure

the knife driver.

Wear protective goggles and protective

gloves when you grind the knives.

Ballast

Always attach ballast properly at the

attachment points provided.

Snow pusher

Attach snow pusher correctly! Wear non-

slip shoes.

When swivelling the snow pusher, mind

pinching and shearing points.

Ensure that the working speed is

adapted to the prevailing working condi-

tions. Failure to do so could injure the

driver by the force of the impact when

the vehicle hits an obstacle.

Maintenance and cleaning

Only trained specialist personnel, who

can carry out professional maintenance

and repair, may carry out this work.

Do not carry out maintenance and clean-

ing with the engine running.

When working on the engine always

remove the ignition key (if present) and

also the spark plug connector in the

case of petrol engines.

Protective devices and tools that are

subject to wear and tear must be regu-

larly inspected and replaced if neces-

sary!

Damaged cutting tools must be re-

placed!

When replacing cutting tools use suita-

ble tools and protective gloves.

Do not carry out repair work such as

welding, grinding, drilling, etc. on struc-

tural, safety-relevant parts (such as

steering bar, tractor hitches, etc.)!

Keep the machine and attachments

clean, to avoid the risk of fire.

Regularly check nuts and bolts for tight-

ness and retighten if necessary.

After maintenance and cleaning, ensure

that the protective devices are re-

installed and properly adjusted!

Only use genuine Agria spare parts.

Carry out a functional and safety test

after completing the work.

Storage

Never store the machine in rooms with

open heating.

Do not park the machine in closed

rooms with fuel left in the tank. Fuel

vapours are hazardous.

Engine, fuel and oil

Do not run the engine in a closed room.

There is a high risk of poisoning! There-

fore always replace damaged exhaust

parts.

Safety Instructions

Meadow mower agria 5300

Handle hot engine components with

caution!

The silencer and other engine parts get

very hot when the engine is running and

are still hot directly after the engine is

switched off. Keep a sufficient distance

from hot surfaces and keep children

away from the running engine.

Caution is needed when handling fuel.

There is an increased risk of fire. Never

handle fuel near open flames, ignitable

sparks or hot engine parts.

Do not refuel in closed rooms. No smok-

ing when refuelling!

Refuel only with the engine switched off

and cooled down.

Do not spill fuel. Use a suitable filling

device.

If you spilled fuel, push the machine

away from the spilled liquid before you

start the engine.

Make sure fuel is of the specified quality.

Store fuel in approved containers only.

Drain fuel only outdoors and into suita-

ble containers.

In the interests of safety, replace the fuel

tank cap and other tank caps if dam-

aged.

Store anti-corrosion agents and stabi-

lizer fluids out of the reach of children. If

sickness and vomiting occur, consult a

doctor immediately. In the event of con-

tact with the eyes rinse immediately with

plenty of water. Avoid inhaling vapours.

Read and observe enclosed instructions!

Before disposing of opened and seem-

ingly empty pressurized tins make sure

they are completely empty. Empty them

in a well-ventilated area safe from

sparks and flames. Dispose of tins as

hazardous waste if necessary.

When working with oil, fuel and grease

wear suitable protective gloves and use

skin protection agents if necessary.

Be careful when draining hot oil, danger

of burns.

Make sure the oil used is of the specified

quality. Store in approved containers

only.

Dispose of oil, fuel, grease and filters

separately and properly.

Tyres and tyre pressure

When you work on the wheels ensure

that the machine is parked securely and

is secured against rolling away.

Only skilled specialists are allowed to

repair tyres, using suitable installation

tools.

Check the tyre pressure at regular inter-

vals. There is a risk of explosion from

excessive tyre pressure.

Observe the required tyre pressure

when you use ballast.

Electrical system

Persons with cardiac pacemakers are

not allowed to touch the energized parts

of the ignition system as long as the

engine is running.

Safety Instructions

Meadow mower agria 5300

Description of the warning, prohibition and mandatory signs

Prior to starting up the machine, read and observe the operat-

ing instructions and safety instructions.

Prior to starting cleaning, maintenance or repair work, switch

off the engine and pull the sparking-plug connector.

Keep a safe distance to the mower knives when the engine is

running!

When working with the machine wear individual hearing pro-

tection.

Wear protective gloves.

Wear safety shoes.

Technical Data

Meadow mower agria 5300

2 Technical Data

Machine

Engine: ........................................................................................................... Honda

Clutch: V-belt clutches with tension rollers between engine and gearbox, friction

clutch for reverse gear

Use only genuine Agria V-belts! (see wearing parts page 64)

Gearbox: ..................................................... Worm gear with switchable wheel drive

Gearbox oil: .............................................................. Oil filling volume approx. 0.6 l

Gearbox oil SAE 90 – API - GL5 (e.g. BP Energear Hypo)

Driving speed: .............................................................................. Forward 3.0 km/h

........................................................................................................ Reverse 2.3 km/h

Mowing unit: Central crank drive,

rock shaft speed .......................................................................................... 920 rpm

stroke, dyn ........................................................................................ approx. 56 mm

Steering bar: Vibration-damped, height-adjustable, lateral adjustment without tools

Weight:

Without cutter bar .......................................................................................... 70.0 kg

With cutter bar 105 cm ................................................................................. 84.0 kg

With cutter bar 125 cm ................................................................................. 89.5 kg

Tyres: ......................................................................................... 3.50 - 6 (field tread)

Tyre pressure: ............................................................................................... 0.8 bar

Noise:

Sound-pressure level at the ear of the operator to EN 12733 and EN 1553:

............................................................................................................... L

= 83.3 dB

............................................................................................................ L

= 103.3 dB

Vibrational acceleration value:

At the handlebar handle to EN 12733 and EN 1033:

.............................................................................................................. a

= 9.6 m/s

Technical Data

Meadow mower agria 5300

Dimensions (mm):

a 470

b 630

e 280

h 860-1080

l 1550

m 910 or 1050

(corresponding to cutter bar ver-

sion)

s 375

s Twin tyres 762

A 525

A Twin tyres 857

Technical Data

Meadow mower agria 5300

Petrol engine

Engine make: .................................................................................................. Honda

Type: ............................................................................................................... GX200

Bore x stroke: ......................................................................................... 68 x 54 mm

Displacement: .............................................................................................. 196 cm

Net output: .................................................................... 4.1 kW (5.5 PS) at 3600 rpm

Torque: ..................................................................................... 12.4 Nm at 2500 rpm

Design: ............................... Fan-air-cooled 1-cylinder four-stroke OHV petrol engine

Nominal speed: ............................................................................. 2900 ... 3000 rpm

Upper no-load speed: ................................................................................ 2725 rpm

Idle speed: ..................................................................................... 1250 ... 1600 rpm

Sparking plug: .................................................................................... NGK BPR6ES

Electrode gap: 0.7 ... 0.8 mm

Ignition: .......................................... Electronic magneto ignition system, contactless,

fixed ignition point,

radio-interference-suppressed to VDE 0879

Valve play: (with cold engine) ................................................ intake: 0.15 ± 0.02 mm

exhaust: 0.20 ± 0.02 mm

Starting device: .............................................................................. Cable-pull starter

Fuel: ...................................................................... Commercially available car petrol,

Octane rating see engine operating instructions

Fuel consumption: ................................................................................... 313 g/kWh

Capacity of the fuel tank: .................................................................................. 3.1 l

Air filter: ............................................................ Dry filter cartridge with foam prefilter

Carburettor: .................................................................................. Throttle valve type

Mixture adjustment screw: ............................. Basic setting approx. 2 1/8 turn open

Engine oil: ....................................................................... Filling volume approx. 0.6 l

Multigrade oil SAE 10W-30, quality class API-SJ or higher

Slope capability: ................................................................................... < 30° (58 %)

(with engine oil level "max." = upper level mark)

Devices and Operating Elements

Meadow mower agria 5300

3 Devices and Operating Elements

The meadow mower agria 5300 is suit-

able to be used for the maintenance of

green areas and parks as well as in

agriculture and forestry for grass and

meadow mowing and winter service.

When using the machine on public roads

– and during transport – the national

road traffic regulations of the relevant

country must be complied with (marking,

lighting, etc.).

The implements approved in the Agria

sales list are available.

Engine

The four-stoke petrol engine is to be

used with standard petrol (see chapter

Startup, page 27).

During the first 20 hours of operation

(running-in period) do not use the engine

at full power.

The rule of never using the engine at a

higher speed than necessary for the

work in hand applies even after the

running-in period.

High speeds are detrimental to

all engines and significantly reduce

their service life. This especially ap-

plies for no-load operation! Over-

revving the engine (letting it roar) can

result in immediate damage.

Cooling

The engine is cooled with an air blower.

Keep the fan grille at the cable-pull

starter and the cooling fins of the cylin-

der free of dirt and aspirated plant de-

bris.

Idling

Always ensure that the engine idle

speed is adjusted correctly. With speed

regulating lever at idling, the engine

should continue running smoothly.

- agria-Service -

Air filter

The air filter cleans the aspirated air. A

contaminated filter reduces the engine

output.

Ignition system

The petrol engine is equipped with a

contactless electronic ignition system.

We recommend that any necessary

inspections are carried out by a skilled

person only.

Devices and Operating Elements

Meadow mower agria 5300

Speed regulating lever

Use the speed regulating lever (C/9) on the

steering bar to continuously adjust the engine

speed between min = IDLE and max = FULL

THROTTLE as required.

Safety circuit

The machine is equipped with a safety circuit.

O Stop position:

When the safety lever (C/4) is

released, the drives are switched off and the

engine continues running.

I operating position:

For operation, press

down the safety lever (C/4). This establishes a

non-

positive connection between engine and

gearbox.

•

The safety circuit must be operated in two

steps:

1) Pull the stop pawl upwards (disengage)

2) Press the safety lever down.

When the wheel drive or the mowing

drive is switched on, the wheels or mowing

tool

s, respectively, start moving immediately

when the safety lever is pressed down. This

must be borne in mind during operation. If

necessary, switch off drives that are not

needed.

Never tamper with the safety circuit.

Never tie up the safety lever.

The safety lever is used as an

emergency

off switch:

Release the lever in a dangerous

situation. It swings automatically to "STOP"

position!

Devices and Operating Elements

Meadow mower agria 5300

Engine stop switch

The electric engine stop switch (B/14) switches

the ignition system ON/OFF.

"ON" = operating position

"OFF" = engine stop position

Switching to "OFF":

The engine is switched off immediately.

Traction drive

Forward - reverse

The meadow mower is equipped with a for-

ward/reverse gearshift that is integrated in

the

clutch and is manually operated with the clutch

lever (C/5).

Reversing:

1. Release the safety lever (C/4)

Press the stop pawl (C/6) at the manually

operated clutch lever (C/5)

Pull the manually operated clutch lever fully

up.

Traction drive in neutral:

•

Manually operated clutch lever (C/5) pulled

approx. half.

Forward movement:

Press down the manually operated clutch

lever (C/5)

2. Press the safety lever (C/4).

Page is loading ...

Agria 5300 Owner's manual

Brand: Agria

Model: 5300

Category: Lawnmowers

Type: Owner's manual

Download PDF

report

Agria 5300 Owner's manual

Agria 5300 Owner's manual

Related papers

Other documents