Kuzma 70425 User manual

Brand
Kuzma
Model
70425
Type
User manual

Kuzma 70425 is a damping kit suitable for Air line tone arms only. With this kit, you can control tone arm and cartridge resonance. The damping paddle in the silicone oil filled trough damps tone arm resonance in both directions, and this effect increases when the paddle is inserted deeper into the silicone oil. Experimentation is the only way to reach optimum damping, but you can start with the height of the paddle when the needle is in the groove so that the tip of the paddle is just touching the surface of the silicone oil. Then, listen to the sound and increase the depth as needed.

Kuzma 70425 is a damping kit suitable for Air line tone arms only. With this kit, you can control tone arm and cartridge resonance. The damping paddle in the silicone oil filled trough damps tone arm resonance in both directions, and this effect increases when the paddle is inserted deeper into the silicone oil. Experimentation is the only way to reach optimum damping, but you can start with the height of the paddle when the needle is in the groove so that the tip of the paddle is just touching the surface of the silicone oil. Then, listen to the sound and increase the depth as needed.

AIR LINE damping kit
General: Suitable for Air line tone arms only.
The damping kit provides control of tone arm & cartridge resonance. A paddle in the silicone
oil filled trough, damps tone arm resonance in both directions. This effect is increased when
the paddle is inserted deeper into the silicone oil.
The damping kit consists of a trough, bottle of silicone oil and paddle carrier.
INSTALLATION:
1. Mounting of the paddle carrier: remove counterweight from the tone arm. Be careful if
you still have a cartridge in the headshell.
Damping kit: rear view
Move the paddle carrier along towards the bearing carrier and fix it with allen key 1.5 mm in
an upright position. Return the counterweight. Due to the extra weight the tracking force
should be adjusted accordingly!
2. Mounting of the trough: remove washer and screw. Insert the thinner part of the trough
from the inside of the blocking plate, in the gap near to the cueing device, along cueing device
rod. Position the back washer and the screw. Using allen key 2mm, gently fix it. Move the
trough as close as possible towards cueing device, away from the bearing shaft and tighten the
screw.
Black plastic nut
Paddle screw
Trough
Paddle carrier
Damping kit: trough mount
Inserting silicone oil: cut off the tip of the nozzle from PVC bottle. Squeeze silicone oil into
the trough- it will go slowly before it spreads evenly. Fill it up to the line or about half way
up.
Damping change:
Release black plastic nut by hand and rotate the paddle-screw into the trough with allen key
1.5 mm. Bend signal wires away to make space for doing this. To secure paddle at desired
height, fix it with rotating CCW plastic nut, while preventing screw- paddle rotation with
inserted allen key.
Optimisation:
The only way to reach optimum damping is by experimentation. Start with the height of
paddle when the needle is in the groove so, that the tip of the paddle is just touching the
surface of the silicone oil. Listen to the sound and increase the depth. Also observe what
happened when the needle touches the grooves, how the whole assembly moves in a
horizontal level a few times, before stabilising in the groove. If you have a test record observe
how the damping decreases movement of the assembly when resonance occurs.
For a lot of cartridge combinations the best sound will be without the use of damping. But
cartridges with higher compliance might benefit.
Kuzma Ltd
Hotemaze 17A
4205 PREDDVOR
SLOVENIA
www.kuzma.si
Blocking plate
Trough position
  • Page 1 1
  • Page 2 2

Kuzma 70425 User manual

Brand
Kuzma
Model
70425
Type
User manual

Kuzma 70425 is a damping kit suitable for Air line tone arms only. With this kit, you can control tone arm and cartridge resonance. The damping paddle in the silicone oil filled trough damps tone arm resonance in both directions, and this effect increases when the paddle is inserted deeper into the silicone oil. Experimentation is the only way to reach optimum damping, but you can start with the height of the paddle when the needle is in the groove so that the tip of the paddle is just touching the surface of the silicone oil. Then, listen to the sound and increase the depth as needed.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents