2. Dometic
  3. Hydro Flame Universal DC Ignition Control Kit

Dometic Hydro Flame Universal DC Ignition Control Kit Installation guide

  • Hello! I have reviewed the installation instructions for the DOMETIC UNIVERSAL DC Ignition Control Kit. This document outlines the steps for removing the old DSI board and installing the new one, including the use of standoffs and an edge adapter where needed. I'm ready to answer any questions you have about the installation process or the kit's components.
  • What components are included in the kit?
    Is the new DSI board a direct replacement for older systems?
    Do I need to make any wiring changes during installation?
    What should I do if the old board has legs?
    What is the procedure for removing the old DSI board?
KIT INCLUDES:
QTY COMPONENTS
1 New DSI Control Board
2 Standoff
1 Edge Adapter
Revision C, 9/18
LITERATURE NUMBER MPD 31502
hydro flame
TM
UNIVERSAL
DC Ignition Control Kit
•New DSI board is a direct
replacement for all 12 DC older
systems. Use with edge adapter if
applicable. No wiring changes are
required.
•Direct replacement with current
systems.
REMOVAL PROCEDURE-
1. Remove old DSI board by
removing (2) two screws.
INSTALLATION PROCEDURE-
1. Install new board by locating in
same configuration as old board.
2. Use standoffs provided if old
board had legs on the board,
place standoffs between board
and bracket.
3. Secure DSI board to bracket with
existing (2) two screws.
4. If the old board being replaced is
a 05-15 series, new holes will
have to be drilled in DSI bracket
to mount new board.
KIT INCLUDES:
QTY COMPONENTS
1 New DSI Control Board
2 Standoff
1 Edge Adapter
Revision C, 9/18
LITERATURE NUMBER MPD 31502
hydro flame
TM
UNIVERSAL
DC Ignition Control Kit
•New DSI board is a direct
replacement for all 12 DC older
systems. Use with edge adapter if
applicable. No wiring changes are
required.
•Direct replacement with current
systems.
REMOVAL PROCEDURE-
1. Remove old DSI board by
removing (2) two screws.
INSTALLATION PROCEDURE-
1. Install new board by locating in
same configuration as old board.
2. Use standoffs provided if old
board had legs on the board,
place standoffs between board
and bracket.
3. Secure DSI board to bracket with
existing (2) two screws.
4. If the old board being replaced is
a 05-15 series, new holes will
have to be drilled in DSI bracket
to mount new board.
KIT INCLUDES:
QTY COMPONENTS
1 New DSI Control Board
2 Standoff
1 Edge Adapter
Revision C, 9/18
LITERATURE NUMBER MPD 31502
hydro flame
TM
UNIVERSAL
DC Ignition Control Kit
•New DSI board is a direct
replacement for all 12 DC older
systems. Use with edge adapter if
applicable. No wiring changes are
required.
•Direct replacement with current
systems.
REMOVAL PROCEDURE-
1. Remove old DSI board by
removing (2) two screws.
INSTALLATION PROCEDURE-
1. Install new board by locating in
same configuration as old board.
2. Use standoffs provided if old
board had legs on the board,
place standoffs between board
and bracket.
3. Secure DSI board to bracket with
existing (2) two screws.
4. If the old board being replaced is
a 05-15 series, new holes will
have to be drilled in DSI bracket
to mount new board.
KIT INCLUDES:
QTY COMPONENTS
1 New DSI Control Board
2 Standoff
1 Edge Adapter
Revision C, 9/18
LITERATURE NUMBER MPD 31502
hydro flame
TM
UNIVERSAL
DC Ignition Control Kit
•New DSI board is a direct
replacement for all 12 DC older
systems. Use with edge adapter if
applicable. No wiring changes are
required.
•Direct replacement with current
systems.
REMOVAL PROCEDURE-
1. Remove old DSI board by
removing (2) two screws.
INSTALLATION PROCEDURE-
1. Install new board by locating in
same configuration as old board.
2. Use standoffs provided if old
board had legs on the board,
place standoffs between board
and bracket.
3. Secure DSI board to bracket with
existing (2) two screws.
4. If the old board being replaced is
a 05-15 series, new holes will
have to be drilled in DSI bracket
to mount new board.
DOMETIC CORPORATION
1120 North Main Street, Elkhart, IN 46514
Please Visit: WWW.DOMETIC.COM
DOMETIC CORPORATION
1120 North Main Street, Elkhart, IN 46514
Please Visit: WWW.DOMETIC.COM
DOMETIC CORPORATION
1120 North Main Street, Elkhart, IN 46514
Please Visit: WWW.DOMETIC.COM
DOMETIC CORPORATION
1120 North Main Street, Elkhart, IN 46514
Please Visit: WWW.DOMETIC.COM
/