Octane Fitness Q47xi Assembly Instructions

Type
Assembly Instructions

This manual is also suitable for

Q47x Console Box Base Box
Position top cover; hold back edge in place; shift front
edge forward and down.
Press bottom edge to snap cover into place; secure
with B-5 (Qty 2).
Wrap mast boot around mast; tuck into access panel.
107949-001 REV A
©2013 Octane Fitness. All rights reserved.
USA & Canada
888-OCTANE4
Latin America/Asian Pacific
001-763-757-2662
Europe/Middle East/Africa
31-10-2662412
Questions?
octanefitness.com
Pedal
Lever
A
Moving Handlebars
&
Adjustment
B
Information Packet
Base
Assembly Instructions
Base Hardware
Loosen screws on sides of lower shroud.
Fit metal plate behind back shroud and side tabs into
slots over side screws. Secure back with B-4 (Qty 2);
tighten side screws.
Place handelbar covers.
Level &
User Set-up
F
Handlebar
Covers (2)
Q47xi Console Box
Information
Packet
Power Supply
Wireless Heart Rate
Transmitter and Strap
B-7
Console Hardware
Top Cover &
Mast Boot
E
D
Access Panel &
Handlebar Covers
Console Hardware

Powerband
Handle (2)
make sure nut is tight.
Adjust and lock levelers;
Connect power supply to unit and to power outlet.
Complete User Set-up (press and hold Level (/) —
See Operations Manual for instructions.
Before 1st use and as needed, clean tracks with
a cloth and a solution of mild soap and water.
Console Assembly Console Assembly
Access Panel
B-1
(4)
B-4
(2)
#2 Phillips
B-5
(2)
#2 Phillips

B-6
Console
Mast
Mast
Boot
Moving Handlebars
(L and R)
Right
Pedal
Lever
Top Cover
Power Supply
Powerband (2)
Remove bolt from 3-pivot link.
Attach pedal lever; tighten to 33 ft-lb.
Attach handlebar at hub with B-1 (Qty 2), B-2 (Qty 2),
B-3 (Qty 1). Tighten to (30 ft-lb).
Connect heart rate and control button cables.
Repeat for second handlebar.
Mast &
Console
Assembly
C
Mi
Boost
your
Workout
Console
Back
Console
Back
Mi
#2 Phillips
C-2 (5)
#2 Phillips
C-1 (4)
B-2
(4)
B-3
(2)
#2 Phillips
C-2 (5)
17mm
#2 Phillips
C-1 (4)
Slide mast over screws on base; tighten.
Connect cable connector (mast to base, Qty 1); secure
cables to frame with B-6.
Route heart rate cable through rear hole in mast and
connect to base cable.
Connect console cables (2) and ground cable. Position
console assembly over top of mast; attach with C-1
(Qty. 4). Connect power supply to unit and to power
outlet. Verify that console LEDs light and stride motors
move.
Align console back with console assembly. Snap
console back and console assembly together at top.
Secure console back with C-2 (Qty 5).
Optional: Adjust moving handlebars for 2” longer / shorter reach:
Hold handlebar; remove nut and reposition link. (Hole
closest to user provides shortest rech.)
Replace nut; tighten (17 ft-lb).
Repeat for second handlebar. Handlebars must be set to
same position for proper functioning. Call Customer Service
for assistance as needed.
  • Page 1 1

Octane Fitness Q47xi Assembly Instructions

Type
Assembly Instructions
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI