Vertically Driven Products 31700 Installation guide

Brand: Vertically Driven Products

Model: 31700

Type: Installation guide

Vertically Driven Products 31700 is a digital video processor (DVP) that allows you to connect various video sources to your computer and record or stream the video footage. The device is capable of capturing video in various resolutions, including 1080p and 4K, and supports a wide range of video formats.

Some of the key features of the Vertically Driven Products 31700 include:

HDMI and SDI inputs: The DVP has both HDMI and SDI inputs, allowing you to connect a variety of video sources, such as cameras, DVD players, and game consoles.
Video capture: The DVP can capture video in various resolutions, including 1080p and 4K. The captured video can be saved to a hard drive or streamed live over the internet.

Some of the key features of the Vertically Driven Products 31700 include:

HDMI and SDI inputs: The DVP has both HDMI and SDI inputs, allowing you to connect a variety of video sources, such as cameras, DVD players, and game consoles.
Video capture: The DVP can capture video in various resolutions, including 1080p and 4K. The captured video can be saved to a hard drive or streamed live over the internet.

Overhead Sport Bar

Storage Console by VDP

Installation Manual for ’87-Current Wrangler YJ/TJ/JK

#14139.1110

PARTS LIST:

A. STORAGE CONSOLE ASSEMBLY - QTY 1

B. COMPARTMENT LINER PADS - QTY 2

C. MOUNTING BRACKETS SPORT BAR - QTY 2

D. SCREW FOR MOUNTING BRACKETS - QTY 4

E. FLAT WASHER - QTY 4

F. 14.5” HOOK & LOOP STRAP - QTY 4

G. 11” HOOK & LOOP STRAP - QTY 4

REQUIRED TOOLS:

SAFETY GLASSES

P3 PHILLIPS HEAD SCREWDRIVER

1/2” OPEN END WRENCH

TO REDUCE RISK OF SERIOUS INJURY OR PROPERTY DAMAGE:

READ ALL SAFETY MESSAGES AND UNDERSTAND ALL INSTRUCTIONS

AND PROCEDURE NOTICES BEFORE ATTEMPTING TO INSTALL OR USE

THIS PRODUCT.

RISK OF EYE INJURY! SAFETY GLASSES MUST BE WORN AT ALL TIMES

WHILE INSTALLING OR MAINTAINING THIS PRODUCT.

VDP_OVERHEAD_CONSOLE_LTR_Layout 1 3/8/13 10:42 AM Page 1

03082013104306

STEP 1: INSTALL COMPARTMENT

LINER PADS

Before you start, put on safety glasses.

Test fit the Liner Pad by centering it on

the compartment bottom floor. Then

remove the wax paper backer to reveal

the adhesive and CAREFULLY place

the pad into the desired position.

Repeat for the opposite side.

Overhead Storage Console Installation

STEP 2: AFFIX SPORT BAR

MOUNTING BRACKETS

Position a mounting bracket to the

storage console’s driver side mounting

flange as shown. Note the orientation of

the bracket as it sits on top of the con-

sole’s flange and not underneath it.

Insert a screw into each of the two fas-

tener holes and secure from the under-

side using a flat washer followed by a

lock nut for each.

Repeat for opposite

side of console.

Be sure to tighten

all 4 of the nuts.

Compartment Liner Pad

Mounting Bracket Underside view

Screw

1⁄2” Wrench

VDP_OVERHEAD_CONSOLE_LTR_Layout 1 3/8/13 10:42 AM Page 2

03082013104306

Overhead Storage Console Installation

Loop (Fuzzy)

Material shown

facing outward

STEP 3: AFFIX HOOK & LOOP STRAPS

Install a mounting strap through the

Sport Bar Mounting Bracket slots as

shown. Use the 14.5” long straps for

2003-Current Wrangler TJ and JK

sport bar applications.

The 11” long straps are used for 1987-02

YJ and TJ Wrangler applications. Be

sure to have the Hook & Loop Materials

facing the outside as shown.

Install two straps per side.

Loop Material

Hook & Loop

Mounting Straps (2 per side)

Leave 5”

Spacing

for ’87-’06

YJ & TJ

14.5” Straps

for ’03-Current

11” Straps

for ’87-’02

Leave 5”

Spacing

for ’87-’06

YJ & TJ

Leave 7”

Spacing for

’07- Current JK

Leave 7”

Spacing for

’07- Current JK

STEP 4: POSITION THE CONSOLE

For ’87-’06 Wrangler YJ & TJ models, in-

stall the Console at least 5” away from

the windshield frame’s interior edge to

allow complete operation of sun-visors

and top latches.

For ’07-current JK models, the Console

should be placed approximately 7”

away from the windshield frame’s inte-

rior edge to allow complete operation

of sun-visors and top latches.

5”

5” 7”

7”

VDP_OVERHEAD_CONSOLE_LTR_Layout 1 3/8/13 10:42 AM Page 3

03082013104322

STEP 5: INSTALL CONSOLE

Positioned the correct distance away for

your vehicle’s windsheild frame, place

the completed Console assembly onto

the tops of the sport bars as shown.

Note: For JK hardtop applications, it is

necessary to temporarily remove the

Freedom Panels to install the Overhead

Console. For TJ and JK soft top applica-

tions, the removal of door surrounds will

simplify the installation.

Overhead Storage Console Installation

A cooperation by VDP and Quadratec Inc.

This product subject to VDP Warranty Terms.

Instructions Part #12999.9015

Tighten each strap to a snug fit and

engage hook & loop straps to secure

Loop each strap around the sport bar

and through the buckle as shown

VDP_OVERHEAD_CONSOLE_LTR_Layout 1 3/8/13 11:36 AM Page 4

03082013113708

Vertically Driven Products 31700 Installation guide

Brand: Vertically Driven Products

Model: 31700

Type: Installation guide

Some of the key features of the Vertically Driven Products 31700 include:

HDMI and SDI inputs: The DVP has both HDMI and SDI inputs, allowing you to connect a variety of video sources, such as cameras, DVD players, and game consoles.
Video capture: The DVP can capture video in various resolutions, including 1080p and 4K. The captured video can be saved to a hard drive or streamed live over the internet.

Download PDF

report

Vertically Driven Products 31700 Installation guide

Vertically Driven Products 31700 Installation guide

Other documents