Ranger design C13-E Installation guide

Brand
Ranger design
Model
C13-E
Type
Installation guide
INSTALLATION GUIDE
C13-E WIRE MESH PARTITION
Transit Connect Partition ( Wire Mesh, Steel )
For technical support, contact us at 1-800-565-5321 C13-E Installation Guide | REV. F4 | Page 2
REQUIRED ITEMS
2
PERSONS
q Cordless Impact
q Cordless Drill
q Knife
q 1/2" Socket
q 10mm Socket
q T50 Torque Bit
q 1/2" Wrench
q 9/64" Drill Bit
QUICK START GUIDE
q 1.1 Setup..................................................................................................................................................
q 1.2 Partition Assembly..............................................................................................................................
Phase 1 - Assembly
q 2.1 Vehicle Preparation.............................................................................................................................
q 2.2 Wire Mesh Partition Installation..........................................................................................................
Phase 2 - Installation
3 - 4
5
6
7 - 9
For technical support, contact us at 1-800-565-5321 C13-E Installation Guide | REV. F4 | Page 3
PHASE 1 – ASSEMBLY
1.1 SETUP
1.1.2 Verify all parts are present
Item No. Description Qty.
30-106 Wire Mesh Panel 1
30-309 Fastening Clip 16
30-368 Driver Side Bracket 1
30-369 Passenger Side Bracket 1
30-402 Floor Bracket 1
79-932 Warning Label ( Bilingual ) 1
94-3030 Assembly Fastener Bag 1
96-3003 Installation Fastener Bag 1
1.1.1 Unpack components; compare with the bill of materials.
30-402
30-106
30-369
30-309
30-368
For technical support, contact us at 1-800-565-5321 C13-E Installation Guide | REV. F4 | Page 4
32×32×
Flat Washer
5/16", 7/8" OD
ZINC
# 98-116
Hex Bolt
5/16"-18 × 1"
GR-5 ZINC
# 90-208
16×16×
Locknut
5/16"-18
ZINC
# 94-110
16×16×
16×16×
#90-208 Hex Bolt 5/16" × 1"
#98-116 Flat Washer
#98-116 Flat Washer
#94-110 Locknut
1.1.3 Identify the 94-3030 and 96-3003 fastener bags.
94-3030 Fastener Kit Fastener Assembly
96-3003 Fastener Kit Fastener Assembly
# 90-971
Self-Tapping Screw
M6-1.0 × 20mm
1022 BO
10×10× #90-971Self Tapping Screw M6
10×10×
For technical support, contact us at 1-800-565-5321 C13-E Installation Guide | REV. F4 | Page 5
PHASE 1 – ASSEMBLY
1.2 PARTITION ASSEMBLY
1.2.2 Attach oor bracket to the wire mesh partition using 4 fastening clips.
1.2.1 Remove all the PVC from all the parts, then attach the side brackets to the wire mesh partition using 12
fastining clips.
TOOLS
q Cordless Impact
q 1/2" Socket
HARDWARE USED
4× hand-tighten the nuts.
#90-208 Hex Bolt 5/16" × 1"
#98-116 Flat Washer
#98-116 Flat Washer
#94-110 Locknut
TOOLS
q Cordless Impact
q Knife
q 1/2" Socket
q 1/2" Wrench
HARDWARE USED
12×
#90-208 Hex Bolt 5/16" × 1"
#98-116 Flat Washer
#98-116 Flat Washer
#94-110 Locknut
For technical support, contact us at 1-800-565-5321 C13-E Installation Guide | REV. F4 | Page 6
2.1.1 Floor preparation.
TOOLS
q Cordless Impact
q T50 Torque Bit
PHASE 2 – INSTALLATION
2.1 VEHICLE PREPARATION
Remove the 2 D-rings,
for re-use.
For technical support, contact us at 1-800-565-5321 C13-E Installation Guide | REV. F4 | Page 7
2.2.1 Lift the partition inside the van and put it in place, then screws both brackets to the van.
NOTE: Be careful not to overtighten.
PHASE 2 – INSTALLATION
2.2 WIRE MESH PARTITION INSTALLATION
NOTE: Drill the holes using 9/64" drill bit to
remove the paint inside the holes.
HARDWARE USED
10×
TOOLS
q Cordless Drill
q 10mm Socket
q 9/64" Drill Bit
#90-971 Self-Tapping Screw M6
For technical support, contact us at 1-800-565-5321 C13-E Installation Guide | REV. F4 | Page 8
HARDWARE USED
2×
Use the D-ring bolt
TOOLS
q Cordless Impact
q T50 Torque Bit
2.2.2 Attach the oor bracket to the van using 2 D-rings, then tighten the bolts that
attach the froor bracket and lower panel.
For technical support, contact us at 1-800-565-5321 C13-E Installation Guide | REV. F4 | Page 9
2.2.3 Apply the warning label on the passenger side bracket.
NOTE: The english warning label is already
attached to the passenger side
panel.
For technical support, contact us at 1-800-565-5321 C13-E Installation Guide | REV. F4 | Page 10
“Congratulations, you have successfully installed your
C13-E Partition!
Thank you for doing business with us.”
For any feedback or suggestions you may have, please contact: cs@rangerdesign.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

Ranger design C13-E Installation guide

Brand
Ranger design
Model
C13-E
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents