2. Ranger design
  3. C13-E

Ranger design C13-E Installation guide

  • Hello, I'm a chat assistant that has read the Ranger Design C13-E Wire Mesh Installation Guide. This guide provides detailed steps for assembling and installing a wire mesh partition in a Transit Connect vehicle. It includes information on required tools, hardware, and step-by-step instructions. I'm ready to answer any questions you might have about the installation process or the product itself.
  • What tools are required for the partition assembly?
    What tools are needed for the wire mesh partition installation?
    Which hardware is used to attach the side brackets to the wire mesh partition?
INSTALLATION GUIDE
C13-E WIRE MESH PARTITION
Transit Connect Partition ( Wire Mesh, Steel )
For technical support, contact us at 1-800-565-5321 C13-E Installation Guide | REV. F4 | Page 2
REQUIRED ITEMS
2
PERSONS
q Cordless Impact
q Cordless Drill
q Knife
q 1/2" Socket
q 10mm Socket
q T50 Torque Bit
q 1/2" Wrench
q 9/64" Drill Bit
QUICK START GUIDE
q 1.1 Setup..................................................................................................................................................
q 1.2 Partition Assembly..............................................................................................................................
Phase 1 - Assembly
q 2.1 Vehicle Preparation.............................................................................................................................
q 2.2 Wire Mesh Partition Installation..........................................................................................................
Phase 2 - Installation
3 - 4
5
6
7 - 9
For technical support, contact us at 1-800-565-5321 C13-E Installation Guide | REV. F4 | Page 3
PHASE 1 – ASSEMBLY
1.1 SETUP
1.1.2 Verify all parts are present
Item No. Description Qty.
30-106 Wire Mesh Panel 1
30-309 Fastening Clip 16
30-368 Driver Side Bracket 1
30-369 Passenger Side Bracket 1
30-402 Floor Bracket 1
79-932 Warning Label ( Bilingual ) 1
94-3030 Assembly Fastener Bag 1
96-3003 Installation Fastener Bag 1
1.1.1 Unpack components; compare with the bill of materials.
30-402
30-106
30-369
30-309
30-368
For technical support, contact us at 1-800-565-5321 C13-E Installation Guide | REV. F4 | Page 4
32×32×
Flat Washer
5/16", 7/8" OD
ZINC
# 98-116
Hex Bolt
5/16"-18 × 1"
GR-5 ZINC
# 90-208
16×16×
Locknut
5/16"-18
ZINC
# 94-110
16×16×
16×16×
#90-208 Hex Bolt 5/16" × 1"
#98-116 Flat Washer
#98-116 Flat Washer
#94-110 Locknut
1.1.3 Identify the 94-3030 and 96-3003 fastener bags.
94-3030 Fastener Kit Fastener Assembly
96-3003 Fastener Kit Fastener Assembly
# 90-971
Self-Tapping Screw
M6-1.0 × 20mm
1022 BO
10×10× #90-971Self Tapping Screw M6
10×10×
For technical support, contact us at 1-800-565-5321 C13-E Installation Guide | REV. F4 | Page 5
PHASE 1 – ASSEMBLY
1.2 PARTITION ASSEMBLY
1.2.2 Attach oor bracket to the wire mesh partition using 4 fastening clips.
1.2.1 Remove all the PVC from all the parts, then attach the side brackets to the wire mesh partition using 12
fastining clips.
TOOLS
q Cordless Impact
q 1/2" Socket
HARDWARE USED
4× hand-tighten the nuts.
#90-208 Hex Bolt 5/16" × 1"
#98-116 Flat Washer
#98-116 Flat Washer
#94-110 Locknut
TOOLS
q Cordless Impact
q Knife
q 1/2" Socket
q 1/2" Wrench
HARDWARE USED
12×
#90-208 Hex Bolt 5/16" × 1"
#98-116 Flat Washer
#98-116 Flat Washer
#94-110 Locknut
For technical support, contact us at 1-800-565-5321 C13-E Installation Guide | REV. F4 | Page 6
2.1.1 Floor preparation.
TOOLS
q Cordless Impact
q T50 Torque Bit
PHASE 2 – INSTALLATION
2.1 VEHICLE PREPARATION
Remove the 2 D-rings,
for re-use.
For technical support, contact us at 1-800-565-5321 C13-E Installation Guide | REV. F4 | Page 7
2.2.1 Lift the partition inside the van and put it in place, then screws both brackets to the van.
NOTE: Be careful not to overtighten.
PHASE 2 – INSTALLATION
2.2 WIRE MESH PARTITION INSTALLATION
NOTE: Drill the holes using 9/64" drill bit to
remove the paint inside the holes.
HARDWARE USED
10×
TOOLS
q Cordless Drill
q 10mm Socket
q 9/64" Drill Bit
#90-971 Self-Tapping Screw M6
For technical support, contact us at 1-800-565-5321 C13-E Installation Guide | REV. F4 | Page 8
HARDWARE USED
2×
Use the D-ring bolt
TOOLS
q Cordless Impact
q T50 Torque Bit
2.2.2 Attach the oor bracket to the van using 2 D-rings, then tighten the bolts that
attach the froor bracket and lower panel.
For technical support, contact us at 1-800-565-5321 C13-E Installation Guide | REV. F4 | Page 9
2.2.3 Apply the warning label on the passenger side bracket.
NOTE: The english warning label is already
attached to the passenger side
panel.
For technical support, contact us at 1-800-565-5321 C13-E Installation Guide | REV. F4 | Page 10
“Congratulations, you have successfully installed your
C13-E Partition!
Thank you for doing business with us.”
For any feedback or suggestions you may have, please contact: cs@rangerdesign.com
/