PREVOST H3-45 VIP Owner's manual

COACH MANUFACTURER

OWNER’S MANUAL

PA1579

September 2011

PA1579 rev.4

June 2011

Featuring:

 EPA2010 regulations engine with SCR selective catalytic reduction

system

First issue: January 2011, beginning with B-1772

REVISION DESCRIPTION DATE

1 Introduction of Prevost AWARE Adaptive Cruise Braking February 2011

2 Standard engine oil type update – changed to 10W30 June 2011

3 2011 inducement strategy added June 2011

4 Reorganization of manual structure September 2011

FOREWORD i

This PREVOST Private Coach Owner's Manual

has been prepared to thoroughly acquaint you,

the owner, with vehicle equipment and features

in order to fully appreciate and safely enjoy your

vehicle. Of course, you are anxious to drive your

new private coach and test its features, but first

please read this publication carefully to help

ensure enjoyable and trouble free operation.

This book should be kept inside the vehicle at all

times for convenient reference. It is also

suggested that it remains with the vehicle at the

time of resale. Please notify PREVOST CAR

INC. when the vehicle's ownership is transferred

so that our records can be kept up to date. Do

this by filling out the appropriate form at the end

of this manual.

The specifications, descriptions and figures

given are based on the latest information

available at printing time. And because at

PREVOST we are constantly striving to improve

our products, we reserve the right to make

changes at any time without notice and/or

obligation on our part.

Please note that this publication applies to

factory-prepared, conversion-ready luxury

private coaches, manufactured by PREVOST

CAR INC. It describes and explains the

equipment and options available for installation

in our factory. Therefore, there may be

equipment described herein that is not installed

on your vehicle. This publication also does not

cover equipment installed by your interior

designer or system manufacturer.

This manual, or portions thereof, cannot be

reproduced in any form whatsoever, in whole or

in part, without the written consent of PREVOST

CAR INC.

The following words are used to emphasize

particularly important information:

WARNING

Identifies instructions which, if not followed,

could result in serious personal injury or loss

of life.

CAUTION

Denotes instructions which, if not followed,

could cause serious damage to vehicle

components.

NOTE

Indicates supplementary information needed

to fully understand and complete an

instruction.

For your own safety and to ensure prolonged

service life of your private coach, heed our

cautions, warnings and notes. Ignoring them

could result in extensive damage and/or serious

personal injury.

TABLE OF CONTENTS iii

SECTION 1 SAFETY PRECAUTIONS..............................................................................................1-1

SECTION 2 VEHICLE EXTERIOR ....................................................................................................2-1

SECTION 3 VEHICLE INTERIOR .....................................................................................................3-1

SECTION 4 CONTROLS AND INSTRUMENTS...............................................................................4-1

SECTION 5 OTHER FEATURES ......................................................................................................5-1

SECTION 6 STARTING AND STOPPING PROCEDURES..............................................................6-1

SECTION 7 SAFETY FEATURES AND EQUIPMENT .....................................................................7-1

SECTION 8 CARE AND MAINTENANCE ........................................................................................8-1

SECTION 9 TECHNICAL INFORMATION........................................................................................9-1

ABBREVIATIONS

APPENDIX A – SERVICE LITERATURE

APPENDIX B – TROUBLESHOOTING MULTIPLEX

APPENDIX C – ALLISON DIAGNOSTIC TROUBLESHOOTING CODES

APPENDIX D – TPMS TROUBLESHOOTING GUIDE

SAFETY PRECAUTIONS 1-1

SECTION 1 SAFETY PRECAUTIONS

SAFE OPERATING PRACTICES ................................................................................................................2

DEFENSIVE DRIVING PRACTICES............................................................................................................2

OTHER PRECAUTIONS .............................................................................................................................. 3

1-2 SAFETY PRECAUTIONS

SAFE OPERATING PRACTICES

To ensure safe and reliable operation, heed the

following safety precautions.

o Operation and maintenance of the vehicle

must be performed only by qualified

personnel.

o Before driving, conduct a walk around

inspection and check that all baggage

compartment doors and equipment access

doors are securely shut.

o Make sure good visibility is maintained at all

times. Keep windshields clean and free of

obstructions.

o Adjust the driver's seat so that all controls

can be reached easily.

o Always wear your safety belt when driving.

o Check the instrument panel frequently. Do

not operate the vehicle when dials or

indicators do not indicate normal operating

conditions.

o Always pay attention to pedestrians passing

in front and behind the vehicle. Always yield

to pedestrians at pedestrian walkways.

o Do not drive over obstacles on the road.

Empty boxes, piles of leaves, and snowdrifts

could conceal hidden dangers that could

damage the vehicle suspension and

underbody.

o When turning or changing lanes, signal your

intention well in advance.

o When approaching to make a right turn,

reduce the space between the vehicle and

the curb to make sure another vehicle

cannot pass on the right. Since the vehicle

makes wide turns, allow enough space to

make safe turns.

o Switch from high beams to low beams when

meeting or following other vehicles within

500 feet (150 meters).

o Never leave the vehicle unattended with the

engine running or with the key in the ignition.

Turn off the engine, remove keys and apply

the parking brake before leaving the vehicle.

o Shut-off the engine before refueling, adding

oil, performing maintenance or servicing

tasks, unless stated otherwise.

o Fuel is highly flammable and explosive. Do

not smoke when refueling. Keep away from

open flames or sparks.

o Do not run the engine or HVAC system with

access doors left open. Close compartment

doors before operating any equipment.

o Do not remove the surge tank filler cap or

the cooling system pressure cap when the

engine is hot. Let the engine cool down

before removing filler caps.

o Do not attempt to push or pull-start the

vehicle.

o The service life of the vehicle depends on

the kind of maintenance it receives. Always

record any problems and report them

immediately to maintenance personnel. After

each trip, perform a system diagnostic to

check if error codes and anomalies were

recorded in the vehicle electronic modules.

DEFENSIVE DRIVING PRACTICES

o For city driving, allow a four to six second

travel interval between your vehicle and the

vehicle ahead. Increase this travel interval

to six to eight seconds for highway driving.

Increase time interval for driving at night or

in foul weather.

o Be prepared to stop when approaching an

intersection. The stopping distance of the

vehicle increases with the weight and speed.

o Establish eye-to-eye contact with other

drivers and with pedestrians. Use, high

beam and low beam headlights, turn signals

and horn as needed.

o On highway, don't stare at the road ahead.

Keep your eyes moving. Check mirrors and

dashboard instruments frequently.

o To keep the vehicle from drifting across

lanes during highway driving, always look

over the horizon on the road ahead.

o Adjust your speed to road conditions, traffic

and visibility. Never exceed the posted

speed limits.

o If another vehicle is following close behind,

reduce your speed to let the vehicle pass.

For additional information about safe operation

and defensive driving practices, contact the local

department of motor vehicles authority.

1-3 SAFETY PRECAUTIONS

OTHER PRECAUTIONS

WARNING

Prior to working on a system inside vehicle,

make sure to cut electrical power and air

supply. A component could be supplied with

electricity even if the ignition switch is set to

the OFF position and/or a component could

be pressurized even if air tanks are emptied.

Always refer to the appropriate wiring and

pneumatic diagrams prior to working on

electrical and/or pneumatic systems.

NOTE

When the ignition switch is set to the OFF

position, the electrical components are not

energized except for the CECM (Chasis

Electronic Control Module), the battery

equalizer, the preheater system and some

electronic modules; which are energized during

15 minutes after the ignition has been set to

the OFF position. Prior to working on one of

these electrical components, set the battery

master switch in the main power compartment

to the OFF position. If the vehicle will not be

operated for a long period (more than 2

weeks), it is recommended, in order to prevent

the batteries from discharging, to trip the main

circuit breakers located in the main power

compartment to stop the small current drawn

by the radio preset station memory, the CECM

memory and the instrument cluster clock. Note

that the radio station presets will be erased,

same thing for the diagnostic codes history and

the instrument cluster clock will have to be

reset.

CAUTION

Prior to arc welding on the vehicle, refer to

section 00-GENERAL of your maintenance

manual. Precautions have to be taken to

avoid costly damage to the electronic

components.

VEHICLE EXTERIOR 2-1

SECTION 2 VEHICLE EXTERIOR

EXTERIOR VIEW..........................................................................................................................................2

ENGINE COMPARTMENT CURBSIDE DOOR........................................................................................... 3

ENGINE COMPARTMENT DOOR...............................................................................................................3

DPF ACCESS DOOR ...................................................................................................................................4

MAIN POWER COMPARTMENT (BATTERY) ............................................................................................4

ENGINE RADIATOR DOOR ........................................................................................................................5

SCR CATALYTIC CONVERTER ACCESS HATCH ...................................................................................5

CONDENSER COMPARTMENT (WITH OPTIONAL CENTRAL A/C SYSTEM)........................................5

EVAPORATOR COMPARTMENT (WITH OPTIONAL CENTRAL A/C SYSTEM) .....................................6

FRONT ELECTRICAL AND SERVICE COMPARTMENT ..........................................................................7

RECLINING BUMPER COMPARTMENT ....................................................................................................7

BAGGAGE COMPARTMENTS....................................................................................................................7

FUEL AND DIESEL EXHAUST FLUID (DEF) FILLER NECK ACCESS ....................................................8

ENTRANCE DOOR .........................................................................................................................................8

INSIDE OPERATION .......................................................................................................................................8

OUTSIDE OPERATION ....................................................................................................................................9

KEYLESS ENTRY SYSTEM ..............................................................................................................................9

KEYLESS OPERATING INSTRUCTIONS .............................................................................................................9

EXTERIOR REAR VIEW MIRRORS ..........................................................................................................10

ELECTRICALLY ADJUSTED MIRROR...............................................................................................................10

RETRACTABLE BACK-UP CAMERA ......................................................................................................10

120 VOLTS CONNECTOR.........................................................................................................................10

TRAILER HITCH.........................................................................................................................................10

2-2 VEHICLE EXTERIOR

EXTERIOR VIEW

H3-45 VIP EXTERIOR VIEW 18688

1. Engine air intake

2. Engine R.H. side access door

3. Main power compartment

4. Baggage compartment

5. Fuel filler neck and diesel exhaust fluid

(DEF) filler neck access door

6. A/C condenser compartment or baggage

compartment

7. Entrance door

8. Retractable back up camera (optional)

9. Diesel Particulate Filter (DPF) access door

10. Engine compartment rear door

11. Rear-view mirror

12. Reclining bumper compartment

13. Front electrical and service compartment

14. Driver’s power window

15. Heating, ventilating and air conditioning

compartment (HVAC) or baggage

compartment

16. Fuel filler neck access door

17. Auxiliary axle

18. Engine radiator door

19. SCR catalytic converter access door

VEHICLE EXTERIOR 2-3

ENGINE COMPARTMENT CURBSIDE

DOOR

Lock this door using the

exterior compartment key.

Lift up protector cover to

gain access to the lock.

Pull up the door handle to

release the latch and then

pull the door open.

The curbside door has a safety catch on top to

prevent it from closing inadvertently. Release

the safety catch before closing the door.

DOOR HANDLE 18184

The engine compartment curbside door provides

access to the following (if equipped)

 Engine compartment rear door release lever

 Fuel Pro 382 filtration system (optional)

 Primary and secondary air system fill valve

 Booster block terminals

 Wet air tank drain valve

 Engine air filter

 Engine block heater connector

 Power steering fluid reservoir

 Battery charger 110-120 volts connector

WARNING

Unless otherwise stated, do not run the

engine when the engine compartment

curbside door is open.

ENGINE COMPARTMENT DOOR

To open engine

compartment door, first

open engine compartment

curbside door. Lift the

latch release lever, place

hand on the upper right of

the rear door and pull

rearward.

Then, using both hands, lift the door up. Always

engage the safety catch when the engine

compartment rear door is open. Release the

catch before closing the door.

The lighting in the engine compartment turns on

automatically when that door is open if the

engine compartment light switch is set to ON

and the ignition key is set to ON or ACC. Use

this switch to turn off the light if it is not required

when the door is open for an extended period.

When open or not closed properly, an

annunciator pictogram will appear on the

instrument cluster DID. To close the door, lift it

slightly and release the safety catch.

OPENING THE ENGINE COMPARTMENT DOOR 18331

The engine compartment rear door provides

access to the following:

 Engine

 Alternators

 Compressors

 Belt tensioner control valve (see Care and

Maintenance chapter)

 Starter selector switch (see Starting and

Stopping Procedures chapter)

 Engine cooling fluid surge tank and filler cap

2-4 VEHICLE EXTERIOR

 Engine air filter restriction indicator

 Engine oil dipstick

 Engine oil filler cap

 Allison transmission oil dipstick & filler tube

WARNING

Pressurized cylinders assist the engine

compartment door opening. To avoid injury,

stand clear when opening the engine

compartment rear door.

WARNING

Unless otherwise stated, avoid running the

engine when the engine compartment door is

open.

DPF ACCESS DOOR

The engine door must be

open before opening the

diesel particulate filter

access door. To open the

DPF access door, press

the latch release lever.

Using both hands, push

the door up until it locks in

place.

To close the door, press the latch release lever

again and lower the door, holding it with both

hands.

WARNING

Proceed with extreme care when opening the

DPF access door. Hold the door with both

hands and never place your fingers behind

the door panel.

DIESEL PARTICULATE FILTER ACCÈSS DOOR

MAIN POWER COMPARTMENT

(BATTERY)

To unlock the main power

compartment door, use

the exterior compartment

door key. The door will

pop open.

The lighting in the compartment turns on

automatically when the door is open if the ignition

key is set to ON or ACC. When the main power

compartment door is open, an annunciator

pictogram appears on the instrument cluster

DID.

The main power compartment provides access

to the following:

 (4x) 12-volt batteries

 12-volt and 24-volt electrical systems main

circuit breakers for

 Battery charger (optional)

 Vanner battery equalizer

 Battery master switch

 Transmission Electronic Control Unit (TECU)

 Multiplex modules: I/O-A, I/O-B

 Rear fuse box (VECR) & spare fuses

 Relays and diodes

 Electronic ground stud

PARTIAL VIEW OF MAIN POWER COMPARTMENT

VEHICLE EXTERIOR 2-5

MAIN CIRCUIT BREAKERS 12-VOLT & 24-VOLT 06605A

ENGINE RADIATOR DOOR

Open the engine radiator door by pushing on the

release latch located on the left side, behind the

louvers.

RADIATOR DOOR RELEASE LATCH LOCATION 18529

SCR CATALYTIC CONVERTER

ACCESS HATCH

To gain access to the SCR catalytic converter:

1. Open the radiator door first;

2. Pull the catch connecting rod to unlock the

access hatch;

3. Lift the hatch open;

4. Hold the door open by inserting the support

rod free end into the receptacle located on

the left side of the door.

WARNING

After inserting the support rod into the

receptacle, make sure that the rod supports

the door securely from falling down on to your

head or body.

WARNING

External and internal temperatures remain hot

long after engine has been shutdown. Allow

the aftertreatment device and DPF to cool

before handling. Wear protective clothing and

glove while servicing.

ACCESSING THE SCR CATALYTIC CONVERTER 04035

CONDENSER COMPARTMENT (with

optional central A/C system)

To open the condenser compartment door:

1. Open the fuel filler door first;

2. Move the latch bolt pin to the right as shown

(step 1 on image);

3. Rotate the latch handle as shown (step 2);

4. Open the door on the right side when facing

the door.

2-6 VEHICLE EXTERIOR

A/C CONDENSER COMPARTMENT DOOR OPENING

CONDENSER COMPARTMENT (WITH CENTRAL A/C

SYSTEM, DEF TANK NOT SHOWN) 22362

EVAPORATOR COMPARTMENT (with

optional central A/C system)

Find the evaporator compartment door release

latch on the left wall of the adjacent baggage

compartment. Pull the release latch then pull

the evaporator compartment door open.

The evaporator compartment contains relays,

diodes and an I/O-B multiplex module mounted

on a panel located on the R.H. side wall when

facing the compartment.

EVAPORATOR COMPARTMENT ACCESS 18306

EVAPORATOR COMPARTMENT (WITH CENTRAL A/C

SYSTEM ONLY) 22365

HVAC COMPONENTS PANEL 06596B

NOTE

It is important to keep the evaporator

compartment door closed while checking the

HVAC system to prevent faulty readings.

VEHICLE EXTERIOR 2-7

FRONT ELECTRICAL AND SERVICE

COMPARTMENT

Unlock this compartment

door using the exterior

compartment key. Pull up

door handle to release the

latch then pull the door

open.

The lighting in the front electrical & service

compartment turns on automatically when the

door is open if the ignition key is set to ON or

ACC.

The front electrical and service compartment

provides access to the following:

 Front fuse box (VECF) & spare fuses

 ABS module

 Multiplex modules: I/O-A, I/O-B

 Relays & diode blocks

 Windshield washer reservoir

 Headlights washer reservoir

 Reclining bumper opening lever

 Accessory air tank drain valve

 Accessory air tank fill valve

 Electronic ground stud

 CECM & Master ID

 Keyless entry module

FRONT ELECTRICAL & SERVICE COMPARTMENT 06665

FRONT ELECTRICAL & SERVICE COMPARTMENT 14066

RECLINING BUMPER

COMPARTMENT

The front bumper can be tilted downward to give

access to the compartment. Pull the opening

handle located in the front electrical and service

compartment to unlock. Tilt down the bumper to

access the compartment. Push the bumper back

up firmly in place to lock in position.

RECLINING BUMPER OPENING HANDLE 06602

WARNING

The compartment behind the bumper is not

designed for storage. Never store loose

objects in this compartment since they can

interfere with the steering linkage mechanism.

Use care when opening or closing the

reclining bumper compartment to prevent

personal injury

BAGGAGE COMPARTMENTS

The baggage compartment doors can be locked

and unlocked using the exterior compartment

key. Lift up the cover to gain access to the lock.

2-8 VEHICLE EXTERIOR

Pull up door handle to release the latch and then

pull the door open. Pressurized cylinders assist

the opening and closing of the baggage

compartment doors and hold the doors open.

The lighting in the baggage compartments turns

on automatically when the door is opened if the

ignition key is set to ON or ACC.

WARNING

To avoid injury, keep hands clear of door

edge and door frame when closing.

NOTE

To prevent theft and vandalism, always lock

all doors before leaving the vehicle

unattended.

NOTE

The baggage compartment doors can also be

locked and unlocked using:

 The baggage compartments central

locking system switch on the L.H.

dashboard (refer to Controls and

Instruments chapter).

 The keyless entry system.

 The remote entry transmitter (refer to

Controls and Instruments chapter).

FUEL AND DIESEL EXHAUST FLUID

(DEF) FILLER NECK ACCESS

Both fuel filler neck doors must be opened with

the exterior compartment key. To open, turn the

key ¼ turn clockwise and pull the door open.

NOTE

It is recommended to refuel from the curbside

whenever possible, to avoid spilling fuel into

the evaporator compartment. Any amount of

fuel vapor in this compartment would be

carried right up into the cabin by the HVAC

system fresh air intake.

Moreover, the curbside filler neck door is the

only access to the DEF filler neck.

NOTE

Provided the vehicle is parked on level

ground, an automatic nozzle will automatically

shut off when tank is approximately 95% full.

CAUTION

Do not fill to more than 95% of the tank

capacity. Do not "top off" the tank, doing so

may result in fuel spillage when the fuel

expands.

FUEL FILLER DOOR 03093

CAUTION

Diesel exhaust fluid DEF will begin to

crystallize and freeze at 12°F (-11°C) and

expand by 7% when frozen. To allow

expansion without damaging the DEF tank, do

not fill the tank with more than 15.9 gallons

(60 liters).

During vehicle operation, the SCR system is

designed to provide heating for the DEF tank

and supply lines. If DEF freezes when the

vehicle is shut down, start up and normal

operation of the vehicle will not be inhibited. The

SCR heating system is designed to quickly

return the DEF to liquid form and the operation

of the vehicle will not be impacted.

ENTRANCE DOOR

INSIDE OPERATION

Lock or unlock the entrance door from the inside

either by actuating the front entrance door

rocker switch on the R.H. dashboard panel or

using the door inside lock knob.

NOTE

If the alarm system is armed, unlocking the

entrance door from the inside by sliding its

lock knob will not disarm the alarm system.

The alarm will sound.

VEHICLE EXTERIOR 2-9

NOTE

For complete information concerning the

Remote Keyless Entry & Anti-theft Alarm

System, refer to the document included in

your vehicle “publication box”.

DOOR LOCK KNOB INSIDE THE VEHICLE 18187

OUTSIDE OPERATION

The first way of locking and unlocking the

entrance door from the outside is the front

entrance door lock key provided with the

vehicle. Turn key counterclockwise to lock or

clockwise to unlock the entrance door and

disarm the intrusion protection and anti-theft

system.

NOTE

The stepwell lights and entrance overhead

light turn on as the door opens.

NOTE

For complete information concerning the

Keyless Entry System & Anti-theft Alarm

System, refer to the document included in

your vehicle’s “publication box”.

DOOR HANDLE & KEYLESS ENTRY SYSTEM KEYBOARD

KEYLESS ENTRY SYSTEM

By this system, you can lock or unlock the

entrance door and the baggage compartment

doors. Unlocking the entrance door using the

keyless entry system will also disarm the

intrusion protection and anti-theft system. The

keyboard is located below the outside entrance

door handle. The microprocessor/relay module

is pre-programmed by the manufacturer and this

code can not be deleted. Moreover, you can

program your own entry code (e.g. a birthday or

part of a social security number).

The manufacturer's code is:

 On your owner's wallet card

 Taped to the keyless module in the front

electrical & service compartment

 Three stickers are joined to your owner's

wallet card

When you use the keyless entry system, the

keyboard illuminates. Do not push the buttons

with a key, pencil or any other hard object as it

could damage the buttons. Although each button

is provided with two digits separated by a

vertical line, there is only one contact per button.

Press in center of button, i.e. between the two

digits.

You must unlock the entrance door before you

unlock the baggage compartment doors. If you

let more than five seconds pass between the

numbers you press, the system shuts down, and

you have to enter your code again. If the keyless

entry system does not work properly, use the

key or the remote entry transmitter to lock or

unlock entrance door or the baggage

compartment doors.

KEYLESS OPERATING INSTRUCTIONS

1) To unlock the entrance door, enter the five

numbers of the code. After pressing the

fifth number, the stepwell lights and

entrance overhead light turn on and the

door unlocks. During the night, press any

button to illuminate the keyboard and then

enter the code.

When pressing any button, the keyboard

lights up for five seconds.

2) To unlock the baggage and service

compartment doors, press button 3·4 within

five seconds after the code that unlocks the

entrance door.

3) To lock the entrance door, the baggage

compartment doors and arm the intrusion

protection and anti-theft system all at the

2-10 VEHICLE EXTERIOR

same time, press buttons 7·8 and 9·0

simultaneously.

NOTE

The intrusion protection and anti-theft system

will be set after a 30 seconds delay.

For additional information, refer to Other

Features chapter.

EXTERIOR REAR VIEW MIRRORS

The coach is equipped with flat-type and

convex-type rear-view mirrors. Convex mirrors

give a wide angle view. Objects viewed in

convex-type rear-view mirrors appear smaller

and are actually closer than they appear.

To provide good visibility in cold weather, the

mirrors may be equipped with heating elements

activated by a rocker switch located on the

dashboard. Refer to Controls and Instruments

chapter. Thermostats are used to prevent

continuous operation of the heating elements.

CAUTION

Do not attach stick-on type convex mirror

accessories to the heated mirror glass. This

could impede uniform heat distribution on the

mirror surface and could break the mirror

glass.

ELECTRICALLY ADJUSTED MIRROR

Electrically adjusted mirrors are adjusted by the

outside mirror controls located on the L.H.

control panel. Refer to Controls and Instruments

chapter. Manual adjustment is also possible.

Adjust the side-view mirrors until the side of the

vehicle is visible. Adjust the flat-type mirror until

the road behind is in full view.

Conve

x

Fla t

RAMCO REAR-VIEW MIRROR 18443

RETRACTABLE BACK-UP CAMERA

An optional back-up camera is available which

provides the driver with visual assistance when

backing-up. The back-up camera is mounted in

a retractable housing. For additional information,

refer to Controls and Instruments and Care and

maintenance chapters.

NOTE

A switch located in the rear electric

compartment is used to retract the back-up

camera for cleaning or maintenance.

120 VOLTS CONNECTOR

This connector is used with a 120 volts supply

and is connected to the optional engine block

heater. Refer to Starting and Stopping

Procedures chapter.

TRAILER HITCH

Your vehicle may be equipped with a factory

installed trailer hitch which has been designed to

meet the following rating:

 Maximum gross trailer weight: 20,000 lbs

(9072 kg)

 Maximum tongue weight at 6 ½ inches

(165 mm) or less from coupling receiver :

1,500 lbs (680 kg)

TRAILER HITCH 18487

WARNING

The draw bar and the ball used for towing the

trailer should be rated for 20,000 lb capacity

or more.

Page is loading ...

PREVOST H3-45 VIP Owner's manual

This manual is also suitable for

PREVOST H3-45 VIP Owner's manual

Related papers

Other documents