Toro 52in Z Master 4000 Series Riding Mower User manual

Brand: Toro

Model: 52in Z Master 4000 Series Riding Mower

Category: Lawnmowers

Type: User manual

This manual is also suitable for

Form No. 3460-862 Rev B

Z Master

4000 Series Riding

Mower

W ith 48in, 52in, 60in, or 72in TURBO

FORCE

Mower

Model No. 74000 —Serial No. 414269700 and Up

Model No. 74000T A —Serial No. 414070944 and Up

Model No. 74002 —Serial No. 414264408 and Up

Model No. 74004 —Serial No. 414264492 and Up

Model No. 74010 —Serial No. 414067788 and Up

Model No. 74015 —Serial No. 414258607 and Up

Model No. 74020 —Serial No. 414307276 and Up

Model No. 74022 —Serial No. 414300000 and Up

Model No. 74035 —Serial No. 414314541 and Up

Model No. 74050 —Serial No. 414386851 and Up

Model No. 74050T A —Serial No. 414071900 and Up

Model No. 74052 —Serial No. 414070436 and Up

Model No. 74054 —Serial No. 414327670 and Up

Model No. 74054T A —Serial No. 414072030 and Up

Model No. 74055 —Serial No. 414258363 and Up

Model No. 74055T A —Serial No. 414328035 and Up

Original Instructions (EN)

*3460-862*

It is a violation of California Public Resource Code

Section 4442 or 4443 to use or operate the engine on

any forest-covered, brush-covered, or grass-covered

land unless the engine is equipped with a spark

arrester , as dened in Section 4442, maintained in

ef fective working order or the engine is constructed,

equipped, and maintained for the prevention of re.

The enclosed engine owner's manual is supplied

for information regarding the US Environmental

Protection Agency (EP A) and the California Emission

Control Regulation of emission systems, maintenance,

and warranty . Replacements may be ordered through

the engine manufacturer .

Please refer to the engine manufacturer ’ s information

included with the machine.

Gross or Net T orque: The gross or net torque

of this engine was laboratory rated by the engine

manufacturer in accordance with the Society of

Automotive Engineers (SAE) J1940 or J2723. As

congured to meet safety , emission, and operating

requirements, the actual engine torque on this class

of mower will be signicantly lower . Please refer to

the engine manufacturer ’ s information included with

the machine.

W ARNING

CALIFORNIA

Proposition 65 W arning

The engine exhaust from this product

contains chemicals known to the State of

California to cause cancer , birth defects,

or other reproductive harm.

Battery posts, terminals, and related

accessories contain lead and lead

compounds, chemicals known to

the State of California to cause

cancer and reproductive harm. W ash

hands after handling.

Use of this product may cause exposure

to chemicals known to the State of

California to cause cancer , birth defects,

or other reproductive harm.

Introduction

This rotary-blade, riding lawn mower is intended to be

used by professional, hired operators. It is designed

primarily for cutting grass on well-maintained lawns

on residential or commercial properties. Using this

product for purposes other than its intended use could

prove dangerous to you and bystanders.

Read this information carefully to learn how to operate

and maintain your product properly and to avoid

injury and product damage. Y ou are responsible for

operating the product properly and safely .

V isit www .T oro.com for product safety and operation

training materials, accessory information, help nding

a dealer , or to register your product.

Whenever you need service, genuine T oro parts, or

additional information, contact an Authorized Service

Dealer or T oro Customer Service and have the model

and serial numbers of your product ready . Figure 1

identies the location of the model and serial numbers

on the product. W rite the numbers in the space

provided.

Important: W ith your mobile device, you can

scan the QR code on the serial number decal (if

equipped) to access warranty , parts, and other

product information.

g332470

Figure 1

1. Model and serial number location

Model No.

Serial No.

This manual uses 2 words to highlight information.

Important calls attention to special mechanical

81 1 1 L yndale A venue South

Bloomington, MN 55420

Printed in the USA

information and Note emphasizes general information

worthy of special attention.

The safety-alert symbol ( Figure 2 ) appears both in

this manual and on the machine to identify important

safety messages that you must follow to avoid

accidents. This symbol will appear with the word

Danger ,W arning , or Caution .

•Danger indicates an imminently hazardous

situation which, if not avoided, will result in death

or serious injury .

•W arning indicates a potentially hazardous

situation which, if not avoided, could result in

death or serious injury .

•Caution indicates a potentially hazardous situation

which, if not avoided, may result in minor or

moderate injury .

sa-black

Figure 2

Safety-alert symbol

Contents

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

General Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Slope Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Safety and Instructional Decals . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Attachments/Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Before Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Before Operation Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Performing Daily Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Breaking in a New Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Using the Rollover-Protection System

(ROPS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Using the Safety-Interlock System . . . . . . . . . . . . . . . . . . . . 18

Positioning the Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Changing the Seat Suspension . . . . . . . . . . . . . . . . . . . . . . . . . 19

Adjusting the Rear-Shock Assemblies . . . . . . . . . . . . . . 20

During Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

During Operation Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Entering the Operator ’ s Position . . . . . . . . . . . . . . . . . . . . . . . 23

Operating the Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Operating the Mower Blade-Control Switch

(PT O) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Operating the Throttle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Operating the Choke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Starting the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Shutting Of f the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Using the Motion-Control Levers . . . . . . . . . . . . . . . . . . . . . . . 27

Driving the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Using the Side Discharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Adjusting the Height of Cut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Adjusting the Anti-Scalp Rollers . . . . . . . . . . . . . . . . . . . . . . . . 31

Operating T ips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

After Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

After Operation Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Using the Fuel-Shutof f V alve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Using the Drive-Wheel Release V alves . . . . . . . . . . . . . 33

T owing a T railer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

T ransporting the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Maintenance Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Recommended Maintenance Schedule(s) . . . . . . . . . . . 37

Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Greasing the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Lubricating the Mower Deck-Lift Pivots . . . . . . . . . . . . . 39

Greasing the Caster Pivots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Greasing the Caster-Wheel Hubs . . . . . . . . . . . . . . . . . . . . . 40

Engine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Engine Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Identifying the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Servicing a Kawasaki

Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Servicing a Kohler

Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Cleaning the Engine Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Checking the Spark Arrester . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Fuel System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Replacing the Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Servicing the Fuel T ank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Electrical System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Electrical System Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Servicing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Servicing the Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Drive System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Checking the Seat Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Adjusting the T racking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Checking the T ire Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Checking the Wheel Lug Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Brake Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Adjusting the Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Belt Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Inspecting the Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Replacing the Mower Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Replacing the Hydraulic Pump-Drive

Belt ................................................................ 59

Controls System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Adjusting the Control-Handle Position . . . . . . . . . . . . . . 60

Adjusting the Motion-Control Linkage . . . . . . . . . . . . . . . 61

Hydraulic System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Hydraulic System Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Hydraulic-Fluid Specications . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Checking the Hydraulic-Fluid Level . . . . . . . . . . . . . . . . . . . 63

Changing the Hydraulic Fluid and

Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Bleeding the Hydraulic System . . . . . . . . . . . . . . . . . . . . . . . . . 65

Mower Deck Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Blade Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Servicing the Cutting Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Adjusting the Side-to-Side Leveling and the

Blade Slope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Removing the Mower Deck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Replacing the Grass Deector . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Cleaning under the Mower Deck . . . . . . . . . . . . . . . . . . . . . . . 73

Cleaning the Suspension System . . . . . . . . . . . . . . . . . . . . . 73

Disposing of W aste . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Storage Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Cleaning and Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

T roubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Safety

General Safety

This product is capable of amputating hands and

feet and of throwing objects. Always follow all safety

instructions to avoid serious personal injury or death.

•Read and understand the contents of this

Operator ’ s Manual before starting the engine.

•Keep bystanders and children away .

•Do not allow children or untrained people to

operate or service the machine. Allow only people

who are responsible, trained, familiar with the

instructions, and physically capable to operate or

service the machine.

•Always keep the roll bar in the fully raised and

locked position and use the seat belt.

•Do not operate the machine near drop-of fs,

ditches, embankments, water , or other hazards, or

on slopes greater than 15°.

•Do not put your hands or feet near moving

components of the machine.

•Do not operate the machine without all guards,

safety switches, and other safety protective

devices in place and functioning properly .

•Shut of f the engine, remove the key , and wait

for all moving parts to stop before leaving the

operator ’ s position. Allow the machine to cool

before servicing, adjusting, fueling, cleaning, or

storing it.

Slope Indicator

g01 1841

Figure 3

Y ou may copy this page for personal use.

1. The maximum slope you can operate the machine on is 15 degrees . Use the slope chart to determine the degree of slope of

hills before operating. Do not operate this machine on a slope greater than 15 degrees. Fold along the appropriate line

to match the recommended slope.

2. Align this edge with a vertical surface, a tree, building, fence pole, etc.

3. Example of how to compare slope with folded edge

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area

of potential danger . Replace any decal that is damaged or missing.

decaloemmarkt

Manufacturer's Mark

1. This mark indicates that the blade is identied as a part

from the original machine manufacturer .

decalbatterysymbols

Battery Symbols

Some or all of these symbols are on your battery .

1. Explosion hazard 6. Keep bystanders away

from the battery .

2. No re, open ame, or

smoking

7. W ear eye protection;

explosive gases can

cause blindness and other

injuries.

3. Caustic liquid/chemical

burn hazard

8. Battery acid can cause

blindness or severe burns.

4. W ear eye protection. 9. Flush eyes immediately

with water and get medical

help fast.

5. Read the Operator's

Manual .

10. Contains lead; do not

discard

decal99-8936

99-8936

1. Machine speed 4. Neutral

2. Fast 5. Reverse

3. Slow

decal106-5517

106-5517

1. W arning—do not touch the hot surface.

decal107-3069

107-3069

1. W arning–there is no rollover protection when the roll bar is

down.

2. T o avoid injury or death from a rollover accident, keep the

roll bar in the fully raised and locked position and wear

the seat belt. Lower the roll bar only when absolutely

necessary; do not wear the seat belt when the roll bar is

down.

3. Read the Operator's Manual ; drive slowly and carefully .

decal109-6035

109-6035

decal1 15-9625

1 15-9625

1. Parking

brake—disengaged

2. Parking brake—engaged

decal1 16-5610

1 16-5610

1. Hour meter 4. Neutral

2. Power take-of f (PT O) 5. Operator presence switch

3. Parking brake 6. Battery

decal1 16-8283

1 16-8283

1. W arning—read the Operator's Manual for instructions on

torquing the blade bolt/nut to 75 to 81 N∙m (55 to 60 ft-lb).

decal1 17-3848

1 17-3848

1. Thrown object hazard—keep bystanders away .

2. Thrown object hazard, raised deector—do not operate

without the deector , discharge cover , or grass collection

system in place.

3. Cutting/dismemberment hazard of hand or foot, mower

blade—stay away from moving parts; keep all guards and

shields in place.

decal126-4363

126-4363

1. Cutting/dismemberment hazard, fan and entanglement

hazard, belt. Shut of f the engine and remove the key before

adjusting, servicing or cleaning the machine.

decal126-9939

126-9939

1. Read the Operator ’ s

Manual

2. Fill to bottom of ller neck;

warning–do not overll the

tank

decal127-0326

127-0326

1. Read the Operator's

Manual .

3. Remove the key and

read the Operator's

Manual before performing

maintenance.

2. Height of cut

decal133-8062

133-8062

decal139-6699

139-6699

1. Height of cut

Decal 144-0405 is for machines not equipped with an

optional headlight.

decal144-0405

144-0405

1. Headlights 3. Engine speed—slow

2. Engine speed—fast

decal144-2669

144-2669

1. Check the engine-oil level. 4. Grease the caster wheel.

2. Check the hydraulic-uid

level.

5. Read the Operator ’ s

Manual before performing

maintenance.

3. Check the tire pressure.

decal144-2687

144-2687

1. T raction belt routing

Decal 144-6569 is for machines equipped with a

headlight.

decal144-6569

144-6569

1. Headlights 3. Engine speed—slow

2. Engine speed—fast

decal147-7364

147-7364

1. Do not exceed a tongue weight of 22 kg (49 lb); do not

exceed a gross towing weight of 1 13 kg (250 lb); read the

Operator ’ s Manual .

Decal 126-8383 is for machines without MyRide only .

decal126-8383

126-8383

Note: This machine complies with the industry standard stability test in the static lateral and longitudinal tests with the maximum

recommended slope indicated on the decal. Review the instructions for operating the machine on slopes in the Operator ’ s Manual as

well as the conditions in which you would operate the machine to determine whether you can operate the machine in the conditions on

that day and at that site. Changes in the terrain can result in a change in slope operation for the machine.

1. W arning—read the Operator ’ s Manual ; do not operate this

machine unless you are trained; wear hearing protection.

4. Runover/backover hazard—do not carry passengers; look

behind you when mowing in reverse.

2. Cutting/dismemberment hazard of the hand, mower blade;

entanglement hazard of the hand, belt—stay away from

moving parts; keep all guards and shields in place.

5. Thrown object hazard—keep bystanders away .

3. Ramp hazard—do not use dual ramps when loading onto a

trailer; use 1 ramp wide enough for the machine; use a ramp

with a slope less than 15°; back up the ramp when loading the

machine and drive forward of f the ramp when unloading.

6. T ipping hazard—do not use the machine near drop-of fs or

on slopes greater than 15°; only operate across slopes less

than 15°.

Decal 132-0871 is for machines with MyRide only .

decal132-0871

132-0871

Note: This machine complies with the industry standard stability test in the static lateral and longitudinal tests with the maximum

recommended slope indicated on the decal. Review the instructions for operating the machine on slopes in the Operator ’ s Manual as

well as the conditions in which you would operate the machine to determine whether you can operate the machine in the conditions on

that day and at that site. Changes in the terrain can result in a change in slope operation for the machine.

1. W arning—read the Operator ’ s Manual ; all operators should

be trained before operating the machine; wear hearing

protection.

4. T ipping hazard—do not use dual ramps when loading onto a

trailer; use 1 ramp wide enough for the machine; use a ramp

with a slope less than 15°; back up the ramp (in reverse) and

drive forward of f the ramp.

2. Cutting/dismemberment hazard of hand—stay away from

moving parts; keep all guards and shields in place.

5. Runover hazard—do not carry passengers; look behind you

when moving in reverse.

3. Thrown object hazard—keep bystanders away .

6. T ipping hazard—do not use the machine near drop-of fs or

on slopes greater than 15°; only operate across slopes less

than 15°.

Decal 132-5067 is for machines with MyRide only .

decal132-5067

132-5067

1 1

Product Overview

g332505

Figure 4

1. Height-of-cut positions

7. Fuel cap

2. Controls

8. Parking-brake lever

3. Motion-control levers 9. Mower deck

4. Electric deck lift (certain

models only)

10. Caster wheel

5. Roll bar 1 1. Anti-scalp roller

6. Shock assembly

(machines with MyRide

only)

Controls

Become familiar with all the controls before you start

the engine and operate the machine.

Control Panel

g332503

Figure 5

1. Key switch

4. Light switch (for models

with lights only)—optional

kit for other models

2. Blade-control switch

(power takeof f)

5. Hour meter

3. Throttle control

6. Choke control (for

carbureted models only)

Key Switch

The key switch, used to start and shut of f the engine,

has 3 positions: O FF , R UN , and S TART . Refer to

Starting the Engine ( page 26 ) .

Light Switch

For Models with Lights Only

Use the light switch to turn the lights to the O Nposition

or O FF position ( Figure 5 ).

Choke Control

Use the choke control to start a cold engine.

Throttle Control

The throttle controls the engine speed, and it has a

continuous-variable setting from the S LOW to F AST

position ( Figure 5 ).

Blade-Control Switch (Power

T akeoff)

The blade-control switch, represented by a

power-takeof f (PT O) symbol, engages and

disengages power to the mower blades ( Figure 5 ).

Hour Meter

The hour meter records the number of hours the

engine has operated. It operates when the engine

is running. Use these times for scheduling regular

maintenance ( Figure 6 ).

g187133

Figure 6

1. Safety-interlock symbols

3. Battery light

2. Hour meter

Safety-Interlock Indicators

There are symbols on the hour meter that indicate

with a black triangle that the interlock component is

positioned correctly ( Figure 6 ).

Battery-Indicator Light

If you turn the key switch to the O Nposition for a

few seconds, the battery voltage displays in the area

where the hours are normally displayed.

The battery light turns on when the key switch is

turned on and when the charge is below the correct

operating level ( Figure 6 ).

Electronic-Control Unit

Malfunction-Indicator Light

For Models with an EFI Engine Only

The electronic-control unit (ECU) continuously

monitors the operation of the EFI system.

If a problem or fault within the system is detected, the

malfunction-indicator light (MIL) illuminates.

The MIL is the red light located in the right console

panel.

Once the MIL illuminates, make initial troubleshooting

checks; refer to the MIL section under T roubleshooting

( page 75 ) .

If these checks do not correct the problem, further

diagnosis and servicing by an Authorized Service

Dealer is necessary .

Motion-Control Levers

Use the motion-control levers to drive the machine

forward, reverse, and turn either direction ( Figure 4 ).

Neutral-Lock Position

Move the motion-control levers outward from the

center to the N EUTRAL -LOCK position when exiting

the machine ( Figure 27 ). Always position the

motion-control levers into the N EUTRAL -LOCK position

when you stop the machine or leave it unattended.

Parking-Brake Lever

Whenever you shut of f the engine, engage the parking

brake to prevent accidental movement of the machine.

Fuel-Shutoff V alve

Close the fuel-shutof f valve when transporting or

storing the machine; refer to Using the Fuel-Shutof f

V alve ( page 33 ) .

Specications

Note: Specications and design are subject to change without notice.

W idth

48-inch Deck 52-inch Deck 60-inch Deck 72-inch Deck

Without mower deck

129 cm (50-15/16

inches)

137 cm (53-7/8 inches) 140 cm (55 inches) 150 cm (58-15/16

inches)

Deector up 141 cm (55-7/16 inches) 150 cm (58-15/16 inches) 166 cm (65-1/2 inches) 192 cm (75-5/8 inches)

Deector down 160 cm (63-1/8 inches) 171 cm (67-3/16 inches) 191 cm (75-1/4 inches) 223 cm (87-5/8 inches)

Deector removed 132 cm (52-1/8 inches) 141 cm (55-5/8 inches) 156 cm (61-5/8 inches) 187 cm (73-1 1/16

inches)

Length

48-inch, 52-inch, and 60-inch Machines 72-inch Machines

24-inch T ires 26-inch T ires 26-inch T ires

219 cm (86-5/16 inches) 220 cm (86-1/2 inches) 227 cm (89-5/16 inches)

Height

Machines with 24-inch tires Machines with 26-inch tires

Roll Bar—Up

182 cm (71-5/8 inches) 185 cm (73 inches)

Roll Bar—Down (MyRide) 126 cm (49-1/2 inches) 129 cm (50-13/16 inches)

Roll Bar—Down (Non-MyRide) 1 18 cm (46-3/8 inches) 129 cm (50-13/16 inches)

W eight

48-inch machines 52-inch machines 60-inch machines 72-inch machines

512 kg (1,130 lb) 531 to 540 kg (1,170 to 1,190 lb) 535 to 590 kg (1,180 to 1,300

lb)

617 kg (1,360 lb)

T owing Capacity

T ongue W eight

Gross T owing W eight *

22 kg (49 lb) 1 13 kg (250 lb)

*The total weight of the object being towed (e.g., trailer and payload, pull-behind dethatcher , aerator , etc.)

Attachments/Accessories

A selection of T oro approved attachments and accessories is available for use with the machine to enhance

and expand its capabilities. Contact your Authorized Service Dealer or authorized T oro distributor or go to

www .T oro.com for a list of all approved attachments and accessories.

T o ensure optimum performance and continued safety certication of the machine, use only genuine T oro

replacement parts and accessories. Replacement parts and accessories made by other manufacturers could be

dangerous, and such use could void the product warranty .

Operation

Note: Determine the left and right sides of the

machine from the normal operating position.

Before Operation

Before Operation Safety

General Safety

•Do not allow children or untrained people to

operate or service the machine. Local regulations

may restrict the age of the operator . The owner

is responsible for training all operators and

mechanics.

•Inspect the area where you will use the machine,

and remove all objects that could interfere with

the operation of the machine or that the machine

could throw .

•Become familiar with the safe operation of the

equipment, operator controls, and safety signs.

•Check that operator-presence controls, safety

switches, and guards are attached and working

properly . Do not operate the machine unless they

are functioning properly .

•Shut of f the engine, remove the key , and wait

for all moving parts to stop before leaving the

operator ’ s position. Allow the machine to cool

before servicing, adjusting, fueling, cleaning, or

storing it.

•Before mowing, inspect the machine to ensure

that the cutting assemblies are working properly .

•Evaluate the terrain to determine the appropriate

equipment and any attachments or accessories

required to operate the machine properly and

safely .

•W ear appropriate clothing, including eye

protection; long pants; substantial, slip-resistant

footwear; and hearing protection. T ie back long

hair and do not wear loose clothing or loose

jewelry .

•Do not carry passengers on the machine.

•Keep bystanders and pets away from the machine

during operation. Shut of f the machine and

attachment(s) if anyone enters the area.

•Do not operate the machine unless all guards and

safety devices, such as the deectors and the

entire grass catcher , are in place and functioning

properly . Replace worn or deteriorated parts when

necessary .

Fuel Safety

•Fuel is extremely ammable and highly explosive.

A re or explosion from fuel can burn you and

others and can damage property .

– T o prevent a static charge from igniting the

fuel, remove the machine from the truck or

trailer and refuel it on the ground, away from

all vehicles. If this is not possible, place a

portable fuel container on the ground, away

from all vehicles, and ll it; then refuel the

machine from the fuel container rather than

from a fuel-dispenser nozzle.

– Fill the fuel tank outdoors on level ground, in

an open area, and when the engine is cold.

Wipe up any fuel that spills.

– Do not handle fuel when smoking or around an

open ame or sparks.

– Do not remove the fuel cap or add fuel to the

tank while the engine is running or hot.

– If you spill fuel, do not attempt to start the

engine. A void creating a source of ignition until

the fuel vapors have dissipated.

– Store fuel in an approved container and keep

it out of the reach of children.

•Fuel is harmful or fatal if swallowed. Long-term

exposure to vapors can cause serious injury and

illness.

– A void prolonged breathing of vapors.

– Keep your hands and face away from the

nozzle and the fuel-tank opening.

– Keep fuel away from your eyes and skin.

•Do not store the machine or fuel container where

there is an open ame, spark, or pilot light, such

as on a water heater or on other appliances.

•Do not operate the machine without the entire

exhaust system in place and in proper working

condition.

•Keep the fuel-dispenser nozzle in contact with

the rim of the fuel tank or container opening at

all times until fueling is complete. Do not use a

nozzle lock-open device.

•If you spill fuel on your clothing, change your

clothing immediately .

•Do not overll the fuel tank. Replace the fuel cap

and tighten it securely .

•Clean grass and debris from the cutting unit,

muf er , drives, grass catcher , and engine

compartment to help prevent res. Clean up oil or

fuel spills.

Adding Fuel

Recommended Fuel

•For best results, use only clean, fresh (less than

30 days old), unleaded gasoline with an octane

rating of 87 or higher ((R+M)/2 rating method).

•Ethanol : Gasoline with up to 10% ethanol

(gasohol) or 15% MTBE (methyl tertiary butyl

ether) by volume is acceptable. Ethanol and

MTBE are not the same. Gasoline with 15%

ethanol (E15) by volume is not approved for use.

Never use gasoline that contains more than

10% ethanol by volume , such as E15 (contains

15% ethanol), E20 (contains 20% ethanol), or E85

(contains up to 85% ethanol). Using unapproved

gasoline may cause performance problems and/or

engine damage which may not be covered under

warranty .

•Do not use gasoline containing methanol.

•Do not store fuel either in the fuel tank or fuel

containers over the winter unless you use a fuel

stabilizer .

•Do not add oil to gasoline.

Using Stabilizer/Conditioner

Use a fuel stabilizer/conditioner in the machine to

provide the following benets:

•Keeps fuel fresh longer when used as directed by

the fuel-stabilizer manufacturer

•Cleans the engine while it runs

•Eliminates gum-like varnish buildup in the fuel

system, which causes hard starting

Important: Do not use fuel additives

containing methanol or ethanol.

Add the correct amount of fuel stabilizer/conditioner

to the fuel.

Note: A fuel stabilizer/conditioner is most

ef fective when mixed with fresh fuel. T o minimize

the chance of varnish deposits in the fuel system,

use fuel stabilizer at all times.

Filling the Fuel T ank

1. Park the machine on a level surface.

2. Engage the parking brake.

3. Shut of f the engine and remove the key .

4. Clean around the fuel-tank cap.

5. Fill the fuel tank to the bottom of the ller neck

(Figure 7 ).

Note: Do not ll the fuel tank completely full.

The empty space in the tank allows the fuel to

expand.

g036751

Figure 7

Performing Daily

Maintenance

Before starting the machine each day , perform the

Each Use/Daily procedures listed in Maintenance

( page 37 ) .

Breaking in a New Machine

New engines take time to develop full power . Mower

decks and drive systems have higher friction when

new , placing additional load on the engine. Allow

40 to 50 hours of break-in time for new machines to

develop full power and best performance.

Using the

Rollover-Protection System

(ROPS)

W ARNING

T o avoid injury or death from rollover , keep

the roll bar in the fully raised, locked position

and use the seat belt.

Ensure that the seat is secured to the

machine.

W ARNING

There is no rollover protection when the roll

bar is in the down position.

• Lower the roll bar only when absolutely

necessary .

• Do not wear the seat belt when the roll bar

is in the down position.

• Drive slowly and carefully .

• Raise the roll bar as soon as clearance

permits.

• Check carefully for overhead clearances

(i.e., branches, doorways, electrical wires)

before driving under any objects and do

not contact them.

Lowering the Roll Bar

Important: Lower the roll bar only when

absolutely necessary .

1. For both sides of the roll bar , remove the hairpin

cotter and pin.

2. Lower the roll bar to the down position.

Note: There are 2 down positions, as shown

in Figure 9 .

3. Install the 2 pins and secure them with the

hairpin cotters.

g399200

Figure 8

g399199

Figure 9

1. Down position with the

bagger installed

2. Full down position

Raising the Roll Bar

Important: Always use the seat belt with the roll

bar in the raised position.

1. Remove the hairpin cotters and remove the 2

pins.

2. Raise the roll bar to the upright position.

3. Install the 2 pins, and secure them with the

hairpin cotters.

g399201

Figure 10

Using the Safety-Interlock

System

W ARNING

If the safety-interlock switches are

disconnected or damaged, the machine could

operate unexpectedly , causing personal

injury .

• Do not tamper with the interlock switches.

• Check the operation of the interlock

switches daily and replace any damaged

switches before operating the machine.

Understanding the

Safety-Interlock System

The safety-interlock system is designed to prevent the

engine from starting unless the following occurs:

•The parking brake is engaged.

•The blade-control switch (PT O) is disengaged.

•The motion-control levers are in the N EUTRAL -LOCK

position.

The safety-interlock system also is designed to shut

of f the engine when the motion-control levers are

moved from the N EUTRAL -LOCK position with the

parking brake engaged or if you rise from the seat

when the PT O is engaged.

The hour meter has indicators to notify the user when

the interlock component is in the correct position.

When the component is in the correct position, an

indicator displays on the screen.

g187670

Figure 1 1

1. Indicators display when the interlock components are in the

correct position

T esting the Safety-Interlock

System

Service Interval : Before each use or daily

T est the safety-interlock system before you use the

machine each time. If the safety system does not

operate as described below , have an Authorized

Service Dealer repair the safety system immediately .

1. Sit on the seat, engage the parking brake, and

move the blade-control switch (PT O) to the O N

position. T ry starting the engine; the engine

should not start.

2. Sit on the seat, engage the parking brake, and

move the blade-control switch (PT O) to the O FF

position. Move either motion-control lever out

of the N EUTRAL -LOCK position. T ry starting the

engine; the engine should not start. Repeat for

the other control lever .

3. Sit on the seat, engage the parking brake,

move the blade-control switch (PT O) to the O FF

position, and move the motion-control levers

to the N EUTRAL -LOCK position. Now start the

engine. While the engine is running, disengage

the parking brake, engage the blade-control

switch (PT O), and rise slightly from the seat; the

engine should shut of f.

4. Sit on the seat, engage the parking brake,

move the blade-control switch (PT O) to the O FF

position, and move the motion-control levers

to the N EUTRAL -LOCK position. Now start the

engine. While the engine is running, center

either motion control and move (forward or

reverse); the engine should shut of f. Repeat for

other motion control.

5. Sit on the seat, disengage the parking brake,

move the blade-control switch (PT O) to the O FF

position, and move the motion-control levers

to the N EUTRAL -LOCK position. T ry starting the

engine; the engine should not start.

Positioning the Seat

The seat can move forward and backward ( Figure 12 ).

Position the seat where you have the best control of

the machine and are most comfortable.

g027632

Figure 12

Seat for machines with MyRide shown.

Changing the Seat

Suspension

Machines without MyRide™

Suspension System Only

The seat is adjustable to provide a smooth and

comfortable ride. Position the seat where you are

most comfortable.

T o adjust it, turn the knob in front either direction to

provide the best comfort ( Figure 13 ).

g019768

Figure 13

1. Seat-suspension knob

Adjusting the Rear-Shock

Assemblies

Machines with MyRide™

Suspension System Only

The MyRide™ suspension system adjusts to provide

a smooth and comfortable ride. Y ou can adjust the

rear 2-shock assemblies to quickly and easily change

the suspension system. Position the suspension

system where you are most comfortable.

The slots for the rear-shock assemblies have

detent positions for reference. Y ou can position the

rear-shock assemblies anywhere in the slot, not just in

the detent positions. The following graphic shows the

position for a soft or rm ride and the dif ferent detent

positions ( Figure 14 ).

g030065

Figure 14

1. Firmest position 3. Detents in the slots

2. Softest position

Note: Ensure that the left and right rear-shock

assemblies are always adjusted to the same positions.

Adjust the rear-shock assemblies ( Figure 15 ).

g030024

g030019

Figure 15

Page is loading ...

Toro 52in Z Master 4000 Series Riding Mower User manual

Brand: Toro

Model: 52in Z Master 4000 Series Riding Mower

Category: Lawnmowers

Type: User manual

This manual is also suitable for

Download PDF

report

Toro 52in Z Master 4000 Series Riding Mower User manual

This manual is also suitable for

Toro 52in Z Master 4000 Series Riding Mower User manual

Related papers