Hunter Fan 53180 Owner's manual

Type
Owner's manual

This manual is also suitable for

www.HunterFan.com
1.866.268.1936
PAGE
5
30 inches
7 feet
PAGE
2
What to Expect with
Your Installation
Ceiling Bracket
Ladder
PAGE
3
Tools Needed
Table of Contents
Mounting Options
PAGE
18
Operation,
Maintenance &
Cleaning
Troubleshooting
?
?
?
PAGE
16
PAGE
4
PAGE
6
PAGE
10
Wiring
Canopy
Downrod
PAGE
13
Light Kit
PAGE
12
Blades
PAGE
11
PAGE
9
Secondary Hanging
System
Congratulations on purchasing
your new Hunter® ceiling fan! It will
provide comfort and performance
in your home or ofce for many
years. This installation and operation
manual contains complete
instructions for installing and
operating your fan.
We are proud of our work and
appreciate the opportunity to
supply you with the best ceiling fan
available anywhere in the world.
To register your fan, please visit:
www.HunterFan.com/register
Save your receipt for proof of purchase.
Remote Control
PAGE
15
1
M0071-01 • 04/30/14 • © Hunter Fan Company
www.HunterFan.com
1.866.268.1936
M0071-01 • 04/30/14 • © Hunter Fan Company
What to Expect with Your Installation
Know your wiring
If you are unfamiliar
with wiring, use a
qualied electrician.
You may need a
friend to help you.
Check box to see
fan weight
Assess location
30 inches
from blade tip
to nearest wall
or obstruction
7 feet
from bottom
edge of blade
to the oor
Select a downrod length
Assess ceiling angle
Must be able to
secure the fan to
building structure or
fan-rated outlet box
1
2
3
Standard Downrod
for ceilings 8-10 feet high
Shorter Downrod
for fans installed close to ceiling
Longer Downrod
for ceilings 10 feet or higher
2
Ceiling angles greater
than 34° will require an
Angled Mounting Kit.
See page 4 for details.
Read and Save These Instructions
This product conforms to UL Standard 507 and CSA 22.2
No. 113.
WARNINGS
CAUTIONS
w.1 - To reduce the risk of re, electrical shock, or personal
injury, mount fan directly from building structure and/or an
outlet box marked acceptable for fan support of 70 lbs (31.8 kg)
and use the mounting screws provided with the outlet box.
w.2 - To avoid possible electrical shock, before installing or
servicing your fan, disconnect the power by turning off the
circuit breakers to the outlet box and associated wall switch
location. If you cannot lock the circuit breakers in the off
position, securely fasten a prominent warning device, such as a
tag, to the service panel.
w.3 - To reduce the risk of re, electrical shock, or motor damage,
use only Hunter Speed Controls.
w.4 - To reduce the risk of personal injury, do not bend the blade
brackets when installing the blade brackets, balancing the blades,
or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.
c.1 - All wiring must be in accordance with national and local
electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring,
use a qualied electrician.
c.2 - Use only Hunter replacement parts.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules, CSA RSS 210, and Canada ICES-003. These limits are to
provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can
radiate radio frequency energy and if not installed and used in
accordance with the instructions may cause harmful interference
to radio communications.
www.HunterFan.com
1.866.268.1936
3
M0071-01 • 04/30/14 • © Hunter Fan Company
Tools Needed
Ladder
Power Drill
(optional)
9/64” Drill Bit
(optional)
Screwdrivers
Pliers Wire Strippers
If mounting to a support structure, you will also need these tools.
www.HunterFan.com
4
If you have an angled ceiling:
1. You will need a longer downrod (sold separately).
2. If your ceiling angle is greater than 34°, you will
also need an Angled Mounting Kit (sold separately).
Guide Touches
BOTH Ceiling & Wall
S
I
T
U
A
T
I
O
N
1
Guide Touches
Wall
but
NOT Ceiling
S
I
T
U
A
T
I
O
N
2
You need BOTH
a Longer
Downrod &
an Angled
Mounting Kit
You need ONLY
a Longer
Downrod
*most common
If you have a at ceiling:
Hang your fan by a standard downrod (included).
Mounting Options
Use Standard Mounting
or Low-Prole Mounting
to hang the fan from a at ceiling.
Use Angled Mounting
to hang the fan from a
vaulted or angled ceiling.
34
O
CEILING
WALL
OPTION
1
Standard
Mounting
OPTION
2
Angled
Mounting
2 3
SLIDE
toward ceiling
PLACE
against wall
1
FOLD
on dotted line
34°
Use the three steps below to determine if your ceiling angle is greater than 34°
4
Support
Structure
Ceiling
Outlet Box
(required)
Angled
Mounting
Style
Standard
Mounting
Style
Support
Structure
Ceiling
Outlet Box
(required)
1.866.268.1936
M0071-01 • 04/30/14 • © Hunter Fan Company
www.HunterFan.com
1.866.268.1936
Ceiling Bracket
For angled ceilings, point
opening toward peak.
Refer to warning w.1 on pg. 2
If you are unable to do this,
call Technical Support at
1-866-268-1936.
Use wood screws
(included) when securing
to support structure with
approved electrical outlet
box. Drill 9/64” pilot holes
in support structure to aid
in securing ceiling bracket
with hardware found in
the hardware bag.
Use machine screws
(provided with outlet
box) when securing to
existing ceiling fan-rated
outlet box. Make sure
it is securely installed
and is acceptable for fan
support of 31.8 kg (70 lbs)
or less.
Make sure all four (4)
bumpers are still attached.
To avoid possible electrical shock, before installing your fan,
disconnect the power by turning off the circuit breakers to
the outlet box associated with the wall switch location.
Turn Power
OFF
If you are installing multiple
remote-controlled fans on the
same circuit breaker, you may
need to perform a few extra steps
to prevent interference or faulty
operation of your remote controls.
Go to www.HunterFan.com/FAQs
and click “How do I properly install
multiple remote-controlled fans?” for
more information.
5
M0071-01 • 04/30/14 • © Hunter Fan Company
www.HunterFan.com
6
Downrod
Slide
Slide
1 2 3 4 5
678910
Sold Separately
Included
Longer
Downrod
for angled
ceilings or
ceilings 10’ or
higher
Shorter
Downrod
for fans installed
close to ceiling
Standard
Downrod
for ceilings 8-10’ high
Option 1Option 2
Option 3
skip to next page
If you need a different downrod length follow these steps:
Steps 1-5 to remove standard downrod pipe
Steps 6-10 to reassemble with new pipe
Included
(pre-assembled)
1.866.268.1936
M0071-01 • 04/30/14 • © Hunter Fan Company
www.HunterFan.com
7
KEEP!
8”
3/8”
C
U
T
&
S
T
R
I
P
(not to scale)
Remove the pre-installed
setscrew so that the downrod
can be inserted.
Hand tighten the downrod (at
least 4-5 full turns) until it stops.
The wires can be cut, but
leave at least 8” extending
from the top of the downrod.
Downrod (continued)
8”
3/8”
Tighten the setscrew
with pliers. DO NOT
HAND TIGHTEN.
If the setscrew is not tightened
securely, the fan may fall.
K
E
E
P
!
1.866.268.1936
M0071-01 • 04/30/14 • © Hunter Fan Company
www.HunterFan.com
1.866.268.1936
Downrod (continued)
DO NOT PICK THE FAN UP BY THE
CANOPY OR WIRES. Place the downrod
ball into the slot in the ceiling bracket.
Put the wires and downrod through the
canopy. Let the canopy sit loosely on top
of the fan.
8
M0071-01 • 04/30/14 • © Hunter Fan Company
www.HunterFan.com
1.866.268.1936
9
M0071-01 • 04/30/14 • © Hunter Fan Company
Secondary Hanging System
3mm (1/8")
Insert the looped end of the
braided cable through the ceiling
bracket and one of the holes in the
outlet box into the ceiling. Access
the support brace in the ceiling.
You may not be able to do this from
below the ceiling depending on
your installation site.
Drive the wood screw and
washer found in the bag
into the side of the support
brace that holds the outlet box.
Leave 3 mm (1/8”) of space
between the support brace
and the washer.
Wrap the braided cable around
the support brace once creating
a complete circle. Hook the
looped end of the cable over the
wood screw so that the cable
lies between the washer and the
support brace.
Tighten the loop and secure the
screw and washer all the way
down to the support brace. Coil
up the excess cable.
Outlet Box
Ceiling
Support
Brace
Braided
Cable
www.HunterFan.com
1.866.268.1936
Wiring
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
F
R
O
M
R
E
C
E
I
V
E
R
F
R
O
M
C
E
I
L
I
N
G
F
R
O
M
C
E
I
L
I
N
G
B
R
A
C
K
E
T
green/yellow stripe
(grounding)
green/yellow stripe
green/yellow stripe
white
black
blue
white (common out)
black (fan out)
blue (light out)
Note: To connect the wires,
hold the bare metal leads
together and place a wire
connector over them, then twist
clockwise until tight.
Using the blue wire
connectors from the remote
control hardware bag,
connect the white wire
from the receiver (marked
common out”) to the white
wire from fan. Connect the
black wire from the receiver
(marked “fan out”) to the
black wire from the fan.
Connect the blue wire from
the receiver (marked ”light
out”) to the blue wire from
the fan. The red wire from
the receiver will not be used,
it has a pre-installed wire
terminator.
F
R
O
M
F
A
N
F
R
O
M
F
A
N
Using an orange wire
connector from
the hardware bag,
connect the 3 grounding
wires (green, green/
yellow stripe, or bare
copper) coming from the
ceiling, downrod, and
hanging bracket.
F
R
O
M
R
E
C
E
I
V
E
R
Using an orange wire
connector from
the hardware bag,
connect the black wire
(ungrounded) from the
ceiling to the black wire
from the receiver (marked
“live in”). Connect the
white wire (grounded)
from the ceiling to
the white wire from
the receiver (marked
“neutral in” or
common in”).
F
R
O
M
C
E
I
L
I
N
G
black (ungrounded)
white (grounded) white (neutral in)
black (live in)
10
M0071-01 • 04/30/14 • © Hunter Fan Company
www.HunterFan.com
1.866.268.1936
Canopy
Lift the canopy into place so that
the screw holes are aligned.
Position the canopy so that, when
lifted into place, the canopy ts into
the hanging bracket as shown.
Screw
Holes
Insert the two canopy screws
found in the hardware bag.
Note: Fan style may vary.
11
M0071-01 • 04/30/14 • © Hunter Fan Company
www.HunterFan.com
1.866.268.1936
Blades
Your blades are shielded with Dust Armor® which
is a nanotechnology coating that repels dust. For
cleaning the fan, use soft brushes or cloths to prevent
scratching. Cleaning agents may damage the nishes.
Align the three blade holes with the three
blade iron posts. Squeeze the blade and the
blade iron post together.
The ared tops of the blade iron posts
will be fully visible above the blade when
properly assembled.
Blade
Holes
Blade
Iron Post
Flared
Tops
12
M0071-01 • 04/30/14 • © Hunter Fan Company
www.HunterFan.com
13
Align the notches in the sides of the lower
switch housing with the upper switch
housing screws. Lift the lower switch housing.
Twist the lower switch housing clockwise
to lock into place. Then thread the fan
pull chain through the hole in the light kit.
Light Kit
Partially install two of the switch housing
screws found in the bag. Connect
the plugs from the upper and lower
switch housings. Make sure to line up the
colored markings on the connectors.
Install the third switch housing screw.
Tighten all three screws securely.
Make sure the lower switch housing is securely attached to
the upper switch housing. Failure to properly secure all three
switch housing screws could result in the light xture falling.
Switch
Housing
Screw
Notch
Switch
Housing
Screw
1.866.268.1936
M0071-01 • 04/30/14 • © Hunter Fan Company
Want to install your fan without a light kit?
Go to www.HunterFan.com/FAQs and click
“How do I install my fan without the light kit?”
www.HunterFan.com
14
Light Kit (continued)
Note: Glass shade style and number of lights may vary.
Connect the appropriate pull
chain pendant to each of the short
chains coming from the nial
and nial cap. The fan pull chain
controls the speed: from high to
off. The light pull chain controls
the light xture: on and off.
Press the globe and globe keeper
ush against the metal plate. Thread
the light pull chain through the hole
in the center of the nial cap and
thread the fan pull chain through the
hole in the side of the cap. Finally,
thread only the light pull chain through
the hole in the nial and screw the nial
onto the threaded rod.
Install a bulb into each of the
sockets. When necessary, replace
with bulbs of the same wattage.
Note: In compliance with Canadian federal
energy regulations, this ceiling fan contains a
device that restricts its light output. Exceeding
the wattage limit marked on the MAX wattage
sticker afxed to the light socket(s) may result
in re hazard or improper operation.
Light
Pull
Chain
Fan
Pull
Chain
Finial
Finial
Cap
Globe
Keeper
Metal
Plate
Globe
CONGRATULATIONS!
YOU’RE DONE!
See next page for remote
operation instructions.
1.866.268.1936
M0071-01 • 04/30/14 • © Hunter Fan Company
www.HunterFan.com
1.866.268.1936
Remote Control
Note: The remote must be paired before
the fan will operate.
Within 3 minutes of restoring power to
the fan, press both the Fan OFF button and
the Fan ON button for at least 4 seconds.
Your fan will turn on to indicate successful
syncing. If it does not, turn off power to
your fan, wait 1 minute then try again. If
using the transmitter with multiple fans,
repeat this process for each fan.
Fan OFF
Fan ON
To access the battery compartment, remove
the small Phillips head screw that secures the
battery door to the transmitter assembly. The
battery should be installed with the positive
(+) side up. Replace with a CR2032 battery
when necessary.
Phillips
Head
Screw
Battery
Door
If you are installing multiple remote-controlled fans on
the same circuit breaker, you may need to perform a few
extra steps to prevent interference or faulty operation of
your remote controls.
Go to www.HunterFan.com/FAQs and click
“How do I properly install multiple remote-controlled fans?”
for more information.
Turn Power
ON
15
M0071-01 • 04/30/14 • © Hunter Fan Company
www.HunterFan.com
1.866.268.1936
Fan Operation:
Press and quickly release the ON or OFF button on the
remote control to turn the fan OFF or ON.
To change the fan speed, slowly pull the fan pull-chain
switch to select the desired speed.
Light Operation:
Press and quickly release the ON or OFF button on the
remote control to turn the light OFF or ON. (Light will
come on at maximum brightness.)
Operation, Maintenance, & Cleaning
Light
Control
Fan
Control
Safe-Exit
Press the Fan Off button for at least three seconds to
initiate the Safe-Exit Mode.
The lights will ash for visual conrmation.
The lights will stay on 50% brightness for 15 seconds and
then begin to dim. After a total of 30 seconds, the lights
will be completely off.
The Safe-Exit Program gives you about thirty seconds
of light when you turn the lights off to exit the room
before the lights go out. To use Safe-Exit:
Note: For CFL lighting, the lights will stay on 100%
brightness for 30 seconds. After a total of 30 seconds, the
lights will be completely off.
16
M0071-01 • 04/30/14 • © Hunter Fan Company
www.HunterFan.com
1.866.268.1936
Cleaning the fan - use soft brushes or
cloths to prevent scratching. Cleaning
products may damage the nishes.
Changing the direction of air ow - move
the reverse switch to the opposite position.
Reverse
Switch
Changing the bulbs - unscrew the nial
and remove it from the threaded rod.
Remove the nial cap and unscrew the
globe keeper while supporting the globe
with your other hand. Carefully remove
the globe. Unscrew bulbs and replace with
bulbs of same type and wattage. Reinstall
the globe assembly.
Finial
Finial
Cap
Globe
Keeper
Metal
Plate
Globe
Operation, Maintenance, & Cleaning (continued)
17
M0071-01 • 04/30/14 • © Hunter Fan Company
For questions regarding removing a light kit, call
customer service 1-866-268-1936.
www.HunterFan.com
1.866.268.1936
Troubleshooting
Excessive wobbling
Make sure that the blades
are properly installed on the
blade iron posts.
Turn the power off, support
the fan carefully, and check
that the hanger ball is
properly seated.
Use the provided balancing
kit and instructions to balance
the fan.
Noisy Operation
Make sure that the blades are
properly installed on the blade
iron posts.
Check to see if any of the blades
are cracked. If so, replace all of
the blades.
Fan doesn’t work
Make sure power switch is on.
Pull the pull chain to make sure
it is on.
Push the motor reversing
switch rmly left or right to
ensure that it is engaged.
Check the circuit breaker to
ensure the power is turned on.
Make sure the blades spin
freely.
Turn off power from the
circuit breaker, then loosen
the canopy and check all the
connections according to the
wiring diagram on page 10.
Check the plug connection in
the switch housing.
Remote control of fan is erratic
Make sure the battery is
installed correctly.
Install a fresh battery.
Transmitter only works when
held at close range
Change battery.
If you have multiple remotes or
multiple remote-controlled fans
installed on the same circuit
breaker and you are experiencing
interference or faulty operation of
your remote controls, please go to
www.HunterFan.com/FAQs
and click “How do I properly install
multiple remote-controlled fans?” for
information on how to correct this
issue.
18
M0071-01 • 04/30/14 • © Hunter Fan Company
CFL bulbs flicker
Turn the light switch off and
back on. Within three minutes,
hold down the Fan Off button
while pressing the Light Off
button twice. If the problem
is not corrected, repeat the
process up to three times.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18

Hunter Fan 53180 Owner's manual

Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI