YukiHalu YUKIHALU-02 User manual

Brand
YukiHalu
Model
YUKIHALU-02
Type
User manual

YukiHalu YUKIHALU-02 is a universal ceiling fan and light remote control kit that allows you to conveniently control your ceiling fan and light fixtures from anywhere in the room. With a wireless transmission range of up to 30 meters in open air, this kit offers flexible control options and eliminates the need for pull chains or wall switches. The receiver and remote are pre-paired in the factory, ensuring easy installation and immediate functionality. The kit features a default mode where the light automatically turns on when the fan is powered, providing added convenience.

YukiHalu YUKIHALU-02 is a universal ceiling fan and light remote control kit that allows you to conveniently control your ceiling fan and light fixtures from anywhere in the room. With a wireless transmission range of up to 30 meters in open air, this kit offers flexible control options and eliminates the need for pull chains or wall switches. The receiver and remote are pre-paired in the factory, ensuring easy installation and immediate functionality. The kit features a default mode where the light automatically turns on when the fan is powered, providing added convenience.

INSTRUCTION FOR UNIVERSAL CEILING FAN REMOTE CONTROLS
CAUTION
READ THIS INSTRUCTION CAREFULLY BEFORE INSTALLATION
1.Make sure the circuit breaker had been turned off before installation.
2.Electrical installation should be performed by a qualified licensed electrician.
3. Spliced conductors should be turned upward and pushed carefully up into the outlet box.
4. Electrical diagrams are for reference only.
SPECIFICATION:
Voltage
Fan
Lamp
85V-264V
50/60HZ
150W
150W(LED)
500W(incandescent)
Wireless Transmission: RF 433MHZ
Remote Control Range:30m（in open air）
Characteristic:
* The kits (receiver and remote) had been paired in factory, so one remote can only control one receiver. If you want to
use one remote to control several receivers, please contact seller.
* In a sufficient space, you can use the receiver at any angle. No worry about the direction.
* The lamp is light up automatically when the ceiling fan is powered on (default mode)
WIRING SCHEMATIC DIAGRAM FOR RECEIVER:
INSTALLATION INSTRUCTION:
Note: Not all ceiling fans have same color wires. Please check which wire
is Fan, light and Neutral carefully before installing.
NOTICES:
1. Install the receiver with the flat side up so that the fan base cover is even with the ceiling
2. The inputs and outputs of the receiver must not be connected backwards
3. Check the dimension of receiver carefully to make sure there is enough space in the canopy of your fan although
the receiver is very small.
4. If you have PULL CHAINS, before installing the wireless remote control kit, use the PULL CHAINS to turn the fan
speed to maximum and turn the fan light on. Only in this way can the pull chains and wireless remote control be
used together, and you can get max speed when press ‘high’ fan button
5. The receiver does not have a REVERSE function
6. Please press every button on remote to check if there is any response from receiver. The receiver buzzer should
sound when you press any button. If there are no feedback sounds, please contact seller for technical support.
7. When remote fails to operate, please check:
a. Is there power to the control unit?
b. Is the control unit wired correctly?
c. Is there a good battery in the remote?
d. Whether there are other remote-controlled products nearby and working? Because remote controlled
products with the same frequency will disturb each other while working in close range.
8. Please use this product under applicable voltage. Low voltage will lead to failure.
9. Please remove the batteries from remote if you will not use this product for a long time.
Please connect the ground wire correctly otherwise it may cause the light micro-light or flash
10. When installing the fan, make sure don’t have fan canopy pinch the antenna (or other wires to prevent a short
circuit).
11. Batteries not included (2x AAA battery)
12. Special function: Keep press ‘STOP’ button for around 6 seconds, the BUZZER in receiver will be TURNED ON or
TURNED OFF, Default setting is ‘ON’.
INSTALLATION STEPS:
1, Disconnect power to fan at the circuit breaker
2, Connect the wires
3, Reinstall fan base so that wire connections are not exposed.
4, Reconnect circuit breaker, You will hear a short sound ‘BI’ from receiver BUZZER, the lamp will turn on automatically
5, Pressing a fan speed button will active the fan
  • Page 1 1

YukiHalu YUKIHALU-02 User manual

Brand
YukiHalu
Model
YUKIHALU-02
Type
User manual

YukiHalu YUKIHALU-02 is a universal ceiling fan and light remote control kit that allows you to conveniently control your ceiling fan and light fixtures from anywhere in the room. With a wireless transmission range of up to 30 meters in open air, this kit offers flexible control options and eliminates the need for pull chains or wall switches. The receiver and remote are pre-paired in the factory, ensuring easy installation and immediate functionality. The kit features a default mode where the light automatically turns on when the fan is powered, providing added convenience.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents