SimpleTech STI-SMRDR/USB User manual

SimpleTech
Brand
SimpleTech
Model
STI-SMRDR/USB
Type
User manual

This manual is also suitable for

USB PhotoReader
for CompactFlash &
SmartMedia Cards
STI-CFRDR/USB, STI-SMRDR/USB
USB CompactFlash
TM
Reader, USB SmartMedia
TM
Reader
User Manual
for Windows 98 & Apple Computers
Page 2
Preface
Thank you for purchasing Simple Technology products. The USB Series
card readers are designed to read and write CompactFlash and SmartMedia
cards when connected to IBM PC/AT-compatible computers equipped with
a USB port running Windows98 or later operating systems or Apple G3,
G4 and iMac computers. (Card compatibility will vary with the specific
card reader model.) To get the most from your card reader, carefully read
the instructions found in this manual before use.
Features:
♦ The card reader is equipped with a USB port (Universal Serial Bus),
the most advanced PC interface for peripherals.
♦ The card reader does not require any external power spply.
♦ The USB CompactFlash PhotoReader (Labeled Type I) is compatible
with Type I CompactFlash Cards.
♦ The USB CompactFlash PhotoReader (Labeled Type I & II) is compatible
with Type I & Type II CompactFlash Cards.
♦ The USB SmartMedia PhotoReader is compatible with SmartMedia
Cards
1. Changes may be made to this product or manual without notification.
2. This manual may not be copied in part, or in whole without express permission.
3. While Simple Technology aims to manufacture its readers to the highest standards, and make its readers compatible with the widest
variety of CompactFlash cards, and computer systems, some incompatibilities may arise. Depending on your system configuration,
USB compatibility may vary. Please look to our web site at http://www.simpletech.com.
MS-DOS and Microsoft Windows are trademarks of Microsoft Corporation.
IBM PC/AT is a trademark of IBM Corporation.
Apple, G3, G4 and iMac are trademarks of the Apple Computer Corporation.
Page 3
Table of Contents
Preface. .......................................................................................... 2
Safety Precautions........................................................................ 4
1. Compatible Systems & OS..................................................... 5
2. Installation Procedure. ........................................................... 5
2.1. Connecting to a Computer. .......................................... 6
2.2. Software Installation for Windows 98 ........................ 8
2.2.1. Installation for Type I CF Readers..................... 9
2.2.2. Installation for Type I/II CF Readers.............. 14
2.2.3. Installation for SM Readers .............................. 19
2.3. Uninstalling the Software in Windows 98 ............... 24
2.4. Software Installation for Apple . ............................... 26
3. Basic Operations. .................................................................. 27
Inserting the Card. ............................................................. 27
Removing the Card. ........................................................... 27
4.1. Using PhotoReader with Windows 98............................. 28
Copying Files. ..................................................................... 28
Formatting Cards. .............................................................. 28
4.2. Using PhotoReader with Apple ....................................... 29
Copying Files. ..................................................................... 29
Formatting Cards. .............................................................. 29
5. Troubleshooting with Windows 98. ................................... 30
6. Specifications. ........................................................................ 31
7. Technical Support. ................................................................ 32
Page 4
Safety Precautions
Please read carefully
This manual is intended to inform you and any other persons who may use this device of possible
dangers and safety instructions, in order to help you maximize your enjoyment of this product, and
to protect you and your equipment from damage.
⋅ Although this manual should cover all possible situations, if you encounter a problem, or
have questions not addressed in the manual, please contact your dealer or our technical
support immediately.
⋅ Simple Technology cannot accept liability for accidents or damage caused through the improper use of
this product
Warning
⋅ Never remove the plastic case from this unit. Some components inside operate at high
voltages and can cause severe electrical shock, if touched.
⋅ Make sure that no liquid is spilled or leaks into this unit and that no metal or inflammable
objects fall inside since this can cause fire, shock, malfunctioning or accidents.
■ Proper Places for Use and Storage
⋅ Do not use or store the unit in an excessively hot or cold place.
⋅ Do not use or store the unit in a dusty place or in direct sunlight.
⋅ In order to prevent possible failures, do not use or store the unit in a place subject to
excessive vibration or in an unstable place.
⋅ Do not place the unit close to a system which generates strong magnetic fields (motor,
transformer, television, loudspeaker, magnet, etc.) to prevent malfunction.
⋅ Do not close vents that may cause internal temperature to rise.
⋅ Do not use in an enclosed (unventilated) area.
■ Precautions for Transportation
⋅ Disconnect cables and remove any PC cards before transporting the unit.
⋅ Use the cardboard box in which the unit was initially packed.
⋅ This is a precision device. Do not subject to excessive shock or vibration.
■ Maintenance of the Plastic Case
⋅ Do not use thinner, benzene, insecticide, or other volatile substances to clean the case, as
this may cause deterioration and delamination of the paint.
⋅ Clean the plastic case and front panel with a soft cloth. Remove severe dirt with a soft cloth
moistened with a small amount of neutral detergent diluted with water. Wipe dry after cleaning.
CompactFlash Cards
Due to the vagueness of some PCMCIA/JEIDA specifications, card products currently on the mar-
kets can differ in some aspects important for compatibility, while still conforming to the standard.
Some commercial cards may be incompatible with hardware or software drivers for the reader/
writer.
Page 5
The PhotoReader requires IBM PC/AT-compatible computers with USB
port running on Windows 98 or later opeating systems. The PhotoReader
is also compatible with Apple G3, G4 and iMac computers running 8.0 or
later operating systems.
1. Compatible Systems & OS
The card reader will not work with older Windows versions. There will be no upgrade
service available at Microsoft Corporation. ["If you have an older Windows version,
you must upgrade to a more recent version. Microsoft does not offer patches for older
Windows versions for compatibility with the card reader."]
Before connecting the card reader,
turn on your computer and start the operating system.
Install the device drivers
Installation is complete.
USB CompactFlash PhotoReader is ready to use.
Restart the computer.
Insert the CompactFlash or SmartMedia Card.
Windows
A "removable disk" drive letter will appear under
"My Computer". Generally, the last available drive
letter will be assigned to the USB PhotoReader.
Apple
The card will be displayed as an icon.
Connect the card reader to the computer
using the USB cable
Follow the guidelines below when installing your card reader.
2. Installation Procedure
Page 6
2A. Connecting to a Computer
Connect the USB PhotoReader to the computer
(using without other peripheral devices)
Connect the USB PhotoReader to the USB port located at the back of the
computer. Make sure the cable ends are firmly connected.
Be careful not to confuse the upper and lower parts of the connector. Do not force
connections, as this may damage the computer or the card reader.
Note: The USB cable from the USB PhotoReader may be plugged into the
computer while the computer is running.
Under Windows 98 operating system, as soon as the USB PhotoReader is
connected, you will see a window displaying the message New Hardware
Found. Proceed to next section for instructions on software installation.
Enlarged View
USB cable from the USB PhotoReader
Page 7
Connect the USB PhotoReader to the computer
through USB hub (using with other peripheral devices)
Connect a USB hub (purchased separately) to your computer's USB port.
Then connect the USB PhotoReader to a port on the USB hub. Make sure
the connections are secured firmly.
Note: The USB cable from the USB PhotoReader may be plugged into the
computer while the computer is running.
Under Windows 98 operating system, as soon as the USB PhotoReader is
connected, you will see a window displaying the message New Hardware
Found. Proceed to next section for instructions on software installation.
Enlarged View
Enlarged View
USB cable from the USB PhotoReader
Page 8
2.1. Software Installation for Windows 98
After you connect the USB PhotoReader to the computer as explained in
the previous chapter, insert the CD containing the software device drivers.
Check and make sure whether your CF USB PhotoReader is compatible
with "Type I CF Cards" or both "Type I & Type II CF Cards" (Check the
label on the device). Proceed to the following sections of the manual for
software installation instructions.
For USB CompactFlash PhotoReader compatible with Type I CompactFlash
Cards, proceed to chapter 2.1.1.
For USB CompactFlash PhotoReader compatible with Type I & Type II
CompactFlash Cards, proceed to chapter 2.1.2.
For USB SmartMedia PhotoReader compatible with SmartMedia Cards,
proceed to chapter 2.1.3.
Page 9
2.1.1. Software Installation for USB CF
PhotoReaders compatible with Type I CF Cards
under Windows 98
1. After you connect the USB PhotoReader to the computer as explained
in the previous chapter, the following window is displayed. Click Next
to continue.
2. The Add new hardware wizard searches for the new drivers and the
following screen is displayed. Click Next to continue.
3. The Add new hardware wizard displays the following screen. Use the
default recommended option. The windows will search for the best
driver for the device. Click Next to continue.
Page 10
4. Windows will prompt you to insert the disk containing the device driver.
Insert the Software Installation CD-ROM in the CD-ROM drive and
click Next to continue. Check the Specify a location, click on the Browse
button, choose Type_I98 and click OK.
5. The Add new hardware wizard will find the device driver "SIMPLE
SM/CF USB PHOTOREADER" and the screen similar to the following
is displayed. Click Next to continue.
Page 11
7. Now, the Add new hardware wizard will display the following screen.
Click Next to continue.
8. The Add new hardware wizard displays the following screen. Use the
default recommended option. The windows will search for the best
driver for the device. Click Next to continue.
6. When the windows finishes installing the device driver, the following
window is displayed. Click Finish to continue.
Page 12
10. The Add new hardware wizard will find the device driver "SIMPLE
CF/SM-USB TO SCSI DRIVER" and the following screen is displayed.
Click Next to continue.
11. When the windows finishes installing the device driver, you will see
the following display. Click Finish to complete the driver installation.
Now, the USB PhotoReader is ready to use.
9. Windows will prompt you to insert the disk containing the device driver.
Insert the Software Installation CD-ROM in the CD-ROM drive and
click Next to continue. Make sure CD-ROM box is ticked.
Page 13
To verify the installation, insert the CompactFlash or the SmartMedia
Card. Double click on "My Computer" icon. The USB PhotoReader will
be displayed as a "Removable Disk". The drive letter assigned may
vary. Generally, the last available drive letter is assigned to the USB
PhotoReader.
Page 14
2.1.2. Software Installation for USB CF
PhotoReaders compatible with Type I & Type II
CF Cards under Windows 98
1. After you connect the USB PhotoReader to the computer as explained
in the previous chapter, the following window is displayed. Click Next
to continue.
2. The Add new hardware wizard searches for the new drivers and the
following screen is displayed. Click Next to continue.
3. The Add new hardware wizard displays the following screen. Use the
default recommended option. The windows will search for the best
driver for the device. Click Next to continue.
Page 15
4. Windows will prompt you to insert the disk containing the device driver.
Insert the Software Installation CD-ROM in the CD-ROM drive and
click Next to continue. Check Specify a location, click on the Browse
button, choose Type_II98 and click OK.
5. The Add new hardware wizard will find the device driver "SIMPLE
SM/CF USB PHOTOREADER" and the screen similar to the following
is displayed. Click Next to continue.
Page 16
7. Now, the Add new hardware wizard will display the following screen.
Click Next to continue.
8. The Add new hardware wizard displays the following screen. Use the
default recommended option. The windows will search for the best
driver for the device. Click Next to continue.
6. When the windows finishes installing the device driver, the following
window is displayed. Click Finish to continue.
Page 17
10. The Add new hardware wizard will find the device driver "SIMPLE
CF/SM-USB TO SCSI DRIVER" and the following screen is displayed.
Click Next to continue.
11. When the windows finishes installing the device driver, you will see
the following display. Click Finish to complete the driver installation.
Now, the USB PhotoReader is ready to use.
9. Windows will prompt you to insert the disk containing the device driver.
Insert the Software Installation CD-ROM in the CD-ROM drive and
click Next to continue. Make sure CD-ROM box is ticked.
Page 18
To verify the installation, insert the CompactFlash or the SmartMedia
Card. Double click on "My Computer" icon. The USB PhotoReader will
be displayed as a "Removable Disk". The drive letter assigned may
vary. Generally, the last available drive letter is assigned to the USB
PhotoReader.
Page 19
2.1.3. Software Installation for USB PhotoReaders
compatible with SmartMedia Cards under
Windows 98
1. After you connect the USB PhotoReader to the computer as explained
in the previous chapter, the following window is displayed. Click Next
to continue.
2. The Add new hardware wizard searches for the new drivers and the
following screen is displayed. Click Next to continue.
3. The Add new hardware wizard displays the following screen. Use the
default recommended option. The windows will search for the best
driver for the device. Click Next to continue.
Page 20
4. Windows will prompt you to insert the disk containing the device driver.
Insert the Software Installation CD-ROM in the CD-ROM drive and
click Next to continue. Check on Specify a location, click on the Browse
button, choose SMwin98 and click OK.
5. The Add new hardware wizard will find the device driver "SIMPLE
SM/CF USB PHOTOREADER" and the screen similar to the following
is displayed. Click Next to continue.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

SimpleTech STI-SMRDR/USB User manual

SimpleTech
Brand
SimpleTech
Model
STI-SMRDR/USB
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents