Invacare Patriot User manual

DEALER: KEEP THIS MANUAL. THE PROCEDURES IN

THIS MANUAL MUST BE PERFORMED BY A INVACARE

DEALER ONLY.

FOURNISSEUR: CONSERVEZ CE MANUEL. LES

PROCÉDURES CONTENUES DANS CE MANUEL

DOIVENT ÊTRE EXÉCUTÉES PAR UN FOURNISSEUR

INVACARE SEULEMENT.

Service Manual - English

PATRIOT



And PATRIOT



SL

Manuel D'entretien - French Canadian

PATRIOT



Et PATRIOT



SL

2

WARNING

W

A

R

N

I

N

G

SAVE THESE INSTRUCTIONS.

SPECIAL NOTES

WARNING/CAUTION notices as used in this manual apply to hazards or unsafe

practices which could result in personal injury or property damage.

NOTICE

THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.

WHEELCHAIR USER

As a manufacturer of wheelchairs, Invacare endeavors to supply a wide variety

of wheelchairs to meet many needs of the end user. However, final selection of

the type of wheelchair to be used by an individual rests solely with the user and

his/her healthcare professional capable of making such a selection.

WHEELCHAIR TIE-DOWN RESTRAINTS AND SEAT POSITIONING STRAPS

Invacare recommends that wheelchair users NOT be transported in vehicles of any

kind while in wheelchairs. As of this date, the Department of Transportation has not

approved any tie-down systems for transportation of a user while in a wheelchair, in a

moving vehicle of any type.

It is Invacare’s position that users of wheelchairs should be transferred into appropri-

ate seating in vehicles for transportation and use be made of the restraints made

available by the auto industry. Invacare cannot and does not recommend any wheel-

chair transportation systems.

AS REGARDS RESTRAINTS - SEAT POSITIONING STRAPS - IT IS THE OBLIGATION OF THE DME

DEALER, THERAPISTS AND OTHER HEALTHCARE PROFESSIONALS TO DETERMINE IF A SEATING

POSITIONING STRAP IS REQUIRED TO ENSURE THE SAFE OPERATION OF THIS EQUIPMENT BY

THE USER. SERIOUS INJURY CAN OCCUR IN THE EVENT OF A FALL FROM A WHEELCHAIR.

WARNING

DO NOT OPERATE THIS EQUIPMENT WITHOUT FIRST

READING AND UNDERSTANDING THIS MANUAL. IF YOU ARE

UNABLE TO UNDERSTAND THE WARNINGS, CAUTIONS, AND

INSTRUCTIONS, CONTACT A HEALTHCARE PROFESSIONAL,

DEALER OR TECHNICAL PERSONNEL IF APPLICABLE BEFORE

ATTEMPTING TO USE THIS EQUIPMENT - OTHERWISE INJURY

OR DAMAGE MAY RESULT.

THE INITIAL SET UP OF THIS WHEELCHAIR MUST BE

PERFORMED BY AN AUTHORIZED INVACARE DEALER OR

QUALIFIED TECHNICIAN.

3

TABLE OF CONTENTS

T

A

B

L

E

O

F

C

O

N

T

E

N

T

S

TABLE OF CONTENTS

SPECIAL NOTES................................................................................................................................... 2

SPECIFICATIONS .................................................................................................................................. 4

PROCEDURE 1 - GENERAL GUIDELINES .......................................................................................... 5

OPERATING INFORMATION ................................................................................................................. 5

PROCEDURE 2 - ASSEMBLY ............................................................................................................... 7

ASSEMBLING THE WHEELCHAIR ....................................................................................................... 7

PROCEDURE 3 - ARMS ........................................................................................................................ 8

REMOVING/INSTALLING FRONT ARM SOCKET/SEAT GUIDE ............................................................ 8

PROCEDURE 4 - SEAT/BACK .............................................................................................................. 9

REPLACING REAR SEAT GUIDES ....................................................................................................... 9

ADJUSTING/REPLACING THE BACK CANES ...................................................................................... 9

REPLACING THE SECTOR BLOCK .................................................................................................. 10

ADJUSTING THE SEAT WIDTH .......................................................................................................... 11

PROCEDURE 5 - WHEELS ................................................................................................................. 13

REMOVING/INSTALLING THE REAR WHEELS .................................................................................. 13

REPLACING SIX OR EIGHT-INCH CASTER/FORK ASSEMBLY ......................................................... 13

FRONT CASTER MOUNTING ADJUSTMENTS .................................................................................. 13

CONVERTING FROM TRAILING TO LEADING OR LEADING TO TRAILING CASTERS ..................... 14

REPOSITIONING/REPLACING CAM ................................................................................................... 14

REPLACING THE WHEEL LOCKS ..................................................................................................... 15

REPLACING THE HIGH MOUNT WHEEL LOCKS ............................................................................ 15

PROCEDURE 6 - PATRIOT ................................................................................................................. 16

REMOVING/INSTALLING REAR ARM SOCKET .................................................................................. 16

REPLACING ARMREST BRACKET .................................................................................................... 17

CONVERTING FROM SPACE SAVER TO CONVENTIONAL OR

CONVENTIONAL TO SPACE SAVER ............................................................................................. 17

REMOVING/INSTALLING AXLE BRACKET .......................................................................................... 18

CONVERTING FROM STANDARD AXLE TO AMPUTEE .................................................................... 19

CHANGING SEAT-TO-FLOOR HEIGHT/SEAT-TO-FLOOR ANGLE .................................................... 19

PROCEDURE 7 - PATRIOT SL............................................................................................................ 31

REPLACING ARMREST ..................................................................................................................... 31

CONVERTING FROM STANDARD AXLE TO AMPUTEE .................................................................... 31

CHANGING SEAT-TO-FLOOR HEIGHT .............................................................................................. 32

LIMITED WARRANTY ........................................................................................................................... 36

4

SPECIFICATIONS

S

P

E

C

I

F

C

A

T

I

O

N

S

* 16x16-inch Seat Frame with packaging.

SPECIFICATIONS

NOTE: All specifications are approximate.

PATRIOT/PATRIOT SL

Overall Width: 21-1/2 , 23-1/2 - 25-1/2, 27-1/2-inches

Overall Depth (w/ riggings): 43 or 45-inches

Seat Width: 14, 16, 17, 18, or 20-inches

Seat Depth: 16 or 18-inches

Seat-to-Floor (ADULT/HEMI): 15-1/2 to 19-1/2-inches - in 1-inch increments

Back Style: Adjustable - in 1-inch increments

Back Height: 15-19-inches (Standard on both) and 20-inch (Optional Back

Cane - Patriot Only)

Arm Styles: Swing Back, Space Saver, Desk/Full Length and

Fixed/Adjustable Height (Desk Length, Swing Back,

Fixed Height Arms - Standard)

Front Riggings: Swingaway Footrests and Elevating Legrests

Rear Axle: Permanent (Standard) and Quick-Release

Rear Wheels: 20, 22 and 24-inch Composite; Urethane,

Pneumatic or Pneumatic-Flat Free Insert -

(Standard - 24-inch Composite Urethane)

Handrims: Composite and Aluminum; Non-Projection and Projection

Standard - Composite Non-Projection

Wheel Locks: Toggle Lock - Push or Pull

Caster Size: 6 x 1-inch Urethane, 8 x 1-inch Urethane (Standard),

8 x 1-1/4-inch Pneumatic or Pneumatic-Flat Free Insert

Upholstery: U240 Black Nylon

Weight: Patriot - 29 lbs.

Patriot SL - 32.5 lbs.

Shipping Weight (Approx.): Patriot - 39.5 lbs.

*

Patriot SL - 43 lbs.

*

NOTE: The seat-to-floor heights are based on urethane tires. If wheelchair is equipped with pneumatic tires or pneu-

matic tires with flat free inserts., add 1/4-inch to the measurements listed above. All heights are approximate to +1/4-

inch due to tire wear and air pressure.

5

G

E

N

E

R

A

L

G

U

I

D

E

L

I

N

E

S

GENERAL GUIDELINES PROCEDURE 1

This Procedure Includes the Following:

Operating Information

OPERATING INFORMATION

GENERAL WARNINGS

Unless otherwise noted, all service and adjustments should be performed while the

wheelchair is unoccupied.

DO NOT use the wheelchair unless it has the proper tire pressure (P.S.I.). The recom-

mended tire pressure is listed on the side wall of the tire. DO NOT overinflate the tires.

Failure to follow these suggestions may cause the tire to explode and cause bodily harm.

SPECIFIC WARNINGS - STABILITY

The back height, front caster position, seat-to-floor angle, position of the rear wheels,

correct anti-tippers as well as the end user's disability or end user's physical condition

and capabilities directly relate to the stability of the wheelchair. Any change to one (1)

or any combination of the eight (8) may cause the wheelchair to decrease in stability.

These adjustments MUST be performed by an authorized Invacare dealer or qualified

technician.

Seat-to-floor heights have specific positions depending on rear wheel size, rear wheel

position, front caster position and seat-to-floor angle. These adjustments MUST be per-

formed by an authorized Invacare dealer or qualified technician.

ANTI-TIPPERS

Anti-tippers are specific to the different seat-to-floor angles and/or seat-to-floor heights.

Refer to the chart in INSTALLING/ADJUSTING THE ANTI-TIPPERS in PROCEDURE 7 of this

manual for correct usage and adjustment. If these requirements CANNOT be achieved,

DO NOT use the wheelchair. Contact Invacare Technical Support at 1-800-832-4707.

Any changes to the seat-to-floor angle or seat-to-floor height may require different

anti-tippers.

CHANGES: 4 5 6 *7 *7 N/A

Back Height N/A N/A

✓ ✓

✓

✓ ✓

✓

✓ ✓

✓

Front Caster

✓✓

✓

✓✓

✓

✓✓

✓

✓✓

✓

✓✓

✓

Seat-to-Floor Angle

✓✓

✓

✓ ✓

✓

✓✓

✓

✓✓

✓

✓ ✓

✓

Rear Wheels

✓✓

✓

✓ ✓

✓

✓✓

✓

✓ ✓

✓

✓✓

✓

Anti-Tippers

✓✓

✓

✓✓

✓

✓ ✓

✓

✓✓

✓

✓✓

✓

User Condition

✓✓

✓

✓✓

✓

✓✓

✓

✓ ✓

✓

✓ ✓

✓

Back Height

Front Caster

Seat-to-Floor

Angle

Rear Wheels

Anti-Tippers

User Condition

PROCEDURE

* NOTE: Refer to the Owner's Manual Part No. 1088909 for

these procedures.

NOTE: When changes to the left hand column occur, follow

across the chart and refer to the

✓ ✓

✓

procedure to maintain the

proper stability, safety and handling of the wheelchair.

6

SPECIFIC WARNINGS - STABILITY (CONTINUED)

Seat-to-floor angle of 0

0

or 3

0

: If so equipped, anti-tippers MUST be attached at all times.

Inasmuch as the anti-tippers are an option for 0

0

or 3

0

on this wheelchair (You may order

with or without the anti-tippers), Invacare strongly recommends using the anti-tippers

as a safeguard for the wheelchair user.

Seat-to-floor angle of 6

0

: If changing the seat-to-floor angle to 6

0

, anti-tippers MUST be

installed.

Seat-to-floor height (which includes seat-to-floor angle): If changing the seat-to-floor

height with or without a change to seat-to-floor angle, the correct anti-tippers MUST

be installed to maintain a 1-1/2 to 2-inch ground clearance.

G

E

N

E

R

A

L

G

U

I

D

E

L

I

N

E

S

GENERAL GUIDELINESPROCEDURE 1

7

This Procedure Includes the Following:

Assembling the Wheelchair

A

S

E

M

B

L

Y

PROCEDURE 2ASSEMBLY

ASSEMBLING THE WHEELCHAIR

(FIGURE 1)

1. Unfold the wheelchair. Refer to FOLDING AND UN-

FOLDING THE WHEELCHAIR in PROCEDURE

1 of the Owner's Manual, part number 1088909.

2. If necessary, adjust the back height. Refer to ADJUST-

ING/REPLACING THE BACK CANES in PROCE-

DURE 4 of this manual.

3. If necessary, install the adjustable tension upholstery.

Refer to INSTALLING/REMOVING ADJUSTABLE

TENSION UPHOLSTERY - PATRIOT ONLY in

PROCEDURE 5 of the Owner's Manual, part num-

ber 1088909.

4. If necessary, install the seat and/or chest positioning

straps. Refer to INSTALLING/REMOVING SEAT

POSITIONING STRAP or INSTALLING/REMOV-

ING CHEST POSITIONING STRAP in PROCE-

DURE 5 of the Owner's Manual, part number 1088909.

5. If necessary, convert standard axle to amputee. Re-

fer to CONVERTING FROM STANDARD AXLE TO

AMPUTEE for Patriot in PROCEDURE 6 OR CON-

VERTING FROM STANDARD AXLE TO AMPU-

TEE for Patriot SL in PROCEDURE 7 of this manual.

6. If necessary, adjust the seat-to-floor height and seat-

to-floor angle. Refer to CHANGING SEAT-TO-

FLOOR HEIGHT/SEAT-TO-FLOOR ANGLE in

PROCEDURE 6 for Patriot OR CHANGING SEAT-

TO-FLOOR HEIGHT in PROCEDURE 7 for Pa-

triot SL of this manual and THEN REPOSITIONING

CAM in PROCEDURE 5 of this manual.

7. If necessary, adjust the front caster height. Refer to

REPLACING SIX OR EIGHT-INCH CASTER/

FORK ASSEMBLY in PROCEDURE 5 of this

manual.

8. If necessary, install the anti-tippers. Refer to INSTALL-

ING/ADJUSTING THE ANTI-TIPPERS in PROCE-

DURE 7 of the Owner's Manual, part number 1088909.

9. Install the front riggings. Refer to INSTALLING/RE-

MOVING SWINGAWAY FOOTREST or INSTALL-

ING/REMOVING ELEVATING LEGREST in PRO-

CEDURE 3 of the Owner's Manual, part number

1088909.

FIGURE 1 - ASSEMBLING THE WHEELCHAIR

Step 1, Procedure 1

Step 2, Procedure 4

Step 3, Procedure 5

Step 5, Procedure 6 or 7

Step 8, Procedure 7

Step 7, Procedure 5

Step 6, Procedure 6 or 7 and 5

Step 6, Procedure 6 or 7

Step 9, Procedure 3

8

PROCEDURE 3 ARMS

This Procedure Includes the Following:

Removing/Installing Front Arm Socket/Seat Guide

WARNING

After ANY adjustments, repair or service

and BEFORE use, make sure all attaching

hardware is tightened securely - other-

wise injury or damage may occur.

REMOVING/INSTALLING FRONT

ARM SOCKET/SEAT GUIDE

(FIGURE 1)

Removing

1. Remove the front armrest from the front arm socket/

seat guide. Refer to ADJUSTING/USING ARM-

REST in PROCEDURE 4 of the Owner's Manual,

part number 1088909.

2. Lift up on the crossbraces to remove the crossbraces

from the seat guides.

3. Remove the mounting screw and locknut that secure

the EXISTING front arm socket/seat guide to the

wheelchair frame.

4. Remove the EXISTING front arm socket/seat guide

from the wheelchair.

5. Repeat STEPS 1-4 for opposite side, if necessary.

6. Install the NEW front arm socket/seat guide onto the

wheelchair. Refer to INSTALLING FRONT ARM

SOCKET/SEAT GUIDE in this procedure of the

manual.

A

R

M

S

FIGURE 1 - REMOVING/INSTALLING

FRONT ARM SOCKET/SEAT GUIDE

Installing

1. Install the NEW front arm socket/seat guide as shown

in FIGURE 1.

2. Install the EXISTING mounting screw through the front

arm socket/seat guide.

3. Install the locknut onto the mounting screw. Securely

tighten.

4. Repeat STEPS 1-3 for opposite side, if necessary.

5. Push down on the crossbraces to install the crossbraces

into the seat guides.

6. Reinstall the front armrest into the front arm socket/

seat guide. Refer to ADJUSTING/USING ARM-

REST in PROCEDURE 4 of the Owner's Manual,

part number 1088909.

NOTE: Crossbraces NOT shown for clarity.

Mounting Screw

Locknut

Front Arm Socket/

Seat Guide

Outside of

Wheelchair

Frame

9

PROCEDURE 4SEAT/BACK

S

E

A

T

/

B

A

C

K

This Procedure Includes the Following:

Replacing Rear Seat Guides

Adjusting/Replacing the Back Canes

Replacing the Sector Block

Adjusting the Seat Width

WARNING

After ANY adjustments, repair or service and

BEFORE use, make sure all attaching hard-

ware is tightened securely - otherwise injury

or damage may occur.

REPLACING REAR SEAT GUIDES

(FIGURE 1)

1. Lift up on the crossbraces to remove crossbraces

from the seat guides.

2. Remove the mounting screw and locknut that secure

EXISTING rear seat guide to wheelchair frame.

3. Remove EXISTING rear seat guide from wheelchair.

4. Install the NEW rear seat guide onto the wheelchair

frame as shown in FIGURE 1.

5. Install the mounting screw through the NEW rear seat

guide and wheelchair frame.

6. Securely tighten the NEW rear seat guide to the wheel-

chair frame with the locknut.

7. Repeat STEPS 2-6 for opposite side, if necessary.

8. Push down on the crossbraces to install the crossbraces

into the seat guides. Wiggle the crossbraces to en-

sure they are secured in the seat guides.

FIGURE 1 - REPLACING REAR SEAT

GUIDES

Mounting

Screw

Rear Seat Guide

Locknut

Outside of

Wheelchair

Frame

NOTE: Crossbraces NOT shown for clarity.

Height

Adjustment

Positions

ADJUSTING/REPLACING THE

BACK CANES

WARNING

BEFORE performing this procedure, refer to

SPECIFIC WARNINGS - STABILITY in PROCEDURE

1 of this manual for additional requirements.

NOTE: Both back canes MUST be positioned at the same

height.

Adjusting

PATRIOT SL (FIGURE 2).

1. Remove the two (2) mounting screws and locknuts that

secure the back cane to the wheelchair frame.

2. Reposition the back cane to one (1) of five (5) height

adjustment positions:

Back Height (in inches)

KHOLE # 1 & 2 2 & 3 3 & 4 4 & 5 5 & 6

HEIGHT 15 16 17 18 19

K Holes numbered from bottom to top for refer-

ence only. (There are no numbers on back canes.)

3. Reinstall the two (2) mounting screws and locknuts

that secure the back cane to the wheelchair frame

and securely tighten.

4. Repeat STEPS 1-3 for the opposite back cane.

5. Secure the back upholstery to the wheelchair frame

with the tie wraps.

Back

Cane

Locknuts

Mounting

Screws

Wheelchair

Frame

FIGURE 2 - ADJUSTING THE BACK

CANES- PATRIOT SL

HOLE

6

5

4

3

2

1

Wheelchair

Frame

10

SEAT/BACKPROCEDURE 4

S

E

A

T

/

B

A

C

K

PATRIOT (FIGURE 3).

1. Remove the one (1) mounting screw and locknut that

secure the back cane to the wheelchair.

2. Do one (1) of the following:

A. 20-inch Back Cane - Position the back cane in

the second hole from the bottom on the wheel-

chair frame as shown in FIGURE 3.

B. Adjustable Back Cane - Reposition the back

cane to one (1) of the five (5) adjustment posi-

tions:

Back Height (in inches)

KHOLE # 12345

HEIGHT 15 16 17 18 19

K Holes numbered from bottom to top for refer-

ence only. (There are no numbers on the back

canes.)

3. Reinstall the one (1) mounting screw and locknut that

secure the back cane to the wheelchair frame. and

securely tighten.

4. Repeat STEPS 1-3 for the opposite back cane.

Back

Cane

Locknut

Wheelchair Frame

Height

Adjustment

Positions

Wheelchair

Frame

HOLE

5

4

3

2

1

FIGURE 3- ADJUSTING THE BACK CANES

- PATRIOT

REPLACING THE SECTOR BLOCK

(FIGURE 4)

1. Remove the front rigging from the wheelchair. Refer to

INSTALLING/REMOVING SWINGAWAY FOOT-

REST or INSTALLING/REMOVING ELEVATING

LEGREST/CALFPAD ASSEMBLY in PROCE-

DURE 3 of the Owner's Manual, part number 1088909.

2. Remove the hex screw and washer that secure the

EXISTING sector block to the wheelchair frame.

3. Remove EXISTING sector block from wheelchair.

4. Position the NEW sector block on the wheelchair frame

with the locking pin facing UP as shown in FIGURE 4.

5. Apply Loctite 242

®

to threads of EXISTING hex screw.

6. Securely tighten the NEW sector block to the wheel-

chair frame with the EXISTING hex screw and washer.

7. Repeat STEPS 1-6 for opposite side, if necessary.

8. Install the front rigging onto the wheelchair. Refer to

INSTALLING/REMOVING SWINGAWAY FOOT-

REST or INSTALLING/REMOVING ELEVATING

LEGREST/CALFPAD ASSEMBLY in PROCE-

DURE 3 of the Owner's Manual, part number 1088909.

Replacing (FIGURES 2 AND 3)

1. Cut the tie wraps that secure the EXISTING back up-

holstery to the wheelchair frame.

2. Remove the EXISTING back upholstery from the

wheelchair. Refer to REMOVING/INSTALLING THE

BACK UPHOLSTERY in PROCEDURE 5 of the

Owner's Manual, part number 1088909.

3. Do one (1) of the following:

A. Patriot SL - Remove the two (2) mounting

screws and locknuts that secure the back cane

to the wheelchair frame.

B. Patriot - Remove the one (1) mounting screw

and locknut that secures the back cane to the

wheelchair frame.

4. Repeat STEP 3 for the opposite side, if necessary.

5. Install the NEW/EXISTING back upholstery onto the

NEW back cane(s). Refer to REMOVING/INSTALL-

ING THE BACK UPHOLSTERY in PROCEDURE

5 of the Owner's Manual, part number 1088909.

6. Secure the NEW back cane(s) to the wheelchair

frame with the EXISTING hardware.

7. Secure the NEW/EXISTING back upholstery to the

wheelchair frame with the NEW tie wraps.

20-inch Back Cane

Wheelchair Frame

Back

Cane

Locknut

Mounting

Screw

Mounting

Screw

Adjustable Back Cane

Loctite

®

- Registered Trademark of Loctite Corporation.

11

PROCEDURE 4SEAT/BACK

S

E

A

T

/

B

A

C

K

ADJUSTING THE SEAT WIDTH

(FIGURE 5)

NOTE: When adjusting the seat width of the wheelchair,

the back and seat upholstery must be changed.

1. Remove the rear wheels. Refer to REMOVING/IN-

STALLING REAR WHEELS in PROCEDURE 6 of

the Owner's Manual, part number 1088909.

2. Remove the EXISTING back and seat upholstery from

the wheelchair. Refer to REMOVING/INSTALLING

THE BACK UPHOLSTERY and REMOVING/IN-

STALLING THE SEAT UPHOLSTERY in PROCE-

DURE 5 of the Owner's Manual, part number 1088909.

3. Remove the four (4) mounting screws and locknuts

that secure the two (2) pivot links to the wheelchair

frame and crossbraces.

4. Remove the two (2) mounting screws, locknuts and

crossbrace saddle that secure the bottom of the

crossbrace to the wheelchair frame.

5. Repeat STEP 4 for opposite crossbrace.

SEAT WIDTH PIVOT LINK

16 to18-inch

14-inch

14-Inch

16-Inch

18-Inch

NOTE: Note the orientation of the coved washers, wash-

ers and locknut for assembling the NEW crossbraces.

See DETAIL "A".

6. Remove the mounting screw, coved washers, wash-

ers and locknut that secure the two (2) crossbraces

together.

7. Assemble the two (2) NEW crossbraces together with

the EXISTING mounting screw, coved washers, wash-

ers and locknut. Securely tighten. Refer to DETAIL

"A" for proper hardware orientation.

8. Determine the correct pivot link and mounting hole to

use with the desired seat width. See chart below.

9. Secure the pivot link to the crossbraces and wheel-

chair frame with the four (4) mounting screws and

locknuts. Securely tighten.

NOTE: Position crossbrace saddle on wheelchair frame

using the washer on the underside of the wheelchair frame

as a reference. See DETAIL "B" for proper positioning of

the crossbrace saddle.

10. Reinstall the two (2) mounting screws, locknuts and

crossbrace saddle that secure the bottom of the NEW

crossbrace to the wheelchair frame. Refer to DE-

TAIL "B" for hardware orientation.

11. Repeat STEP 10 for opposite crossbrace. Securely

tighten.

12. Install the NEW back and seat upholstery onto the

wheelchair. Refer to REMOVING/INSTALLING THE

BACK UPHOLSTERY and REMOVING/INSTALL-

ING THE SEAT UPHOLSTERY in PROCEDURE

5 of the Owner's Manual, part number 1088909.

13. Install the rear wheels. Refer to REMOVING/IN-

STALLING REAR WHEELS in PROCEDURE 6 of

the Owner's Manual, part number 1088909.

DO NOT USE

17

17-Inch

20-inch

20-Inch

DO NOT USE

FIGURE 4 - REPLACING THE SECTOR

BLOCK

Sector Block

Hex Screw

Washer

Wheelchair

Frame

Locking Pin

12

FIGURE 5 - ADJUSTING THE SEAT WIDTH

Crossbrace

Saddle

Washer

Wheelchair

Frame

Crossbrace

Saddle

(STEPS 4,10)

Mounting

Screw

(STEPS 4,10)

Crossbrace

Saddle

(STEPS 4,10)

Locknut

(STEPS

4,10)

Pivot Link

(STEPS 3,8,9)

Locknut

(STEPS 3,9)

Locknut

(STEPS 3,9)

Mounting Screw

(STEPS 3,9)

Wheelchair

Frame

Locknut

(STEPS 3,9)

Mounting Screw

(STEPS 3,9)

Mounting

Screw

Washer

Coved

Washer

Locknut

Washer

Coved

Washer

Coved

Washer

DETAIL "A"

(STEPS 6,7)

DETAIL "B"

Crossbraces

Mounting

Screw

(STEPS 3,9)

Crossbrace

(STEPS 3,5,6,7,9,10)

Mounting

Screw

(STEPS 4,10)

PROCEDURE 4 SEAT/BACK

S

E

A

T

/

B

A

C

K

13

PROCEDURE 5

W

H

E

L

S

WHEELS

This Procedure Includes the Following:

Removing/Installing the Rear Wheels

Replacing Six or Eight-Inch Caster/Fork Assembly

Converting From Trailing to Leading OR Leading

to Trailing Casters

Repositioning/Replacing Cam

Replacing the Wheel Locks

Replacing The High Mount Wheel Locks

WARNING

BEFORE performing ANY of these procedures,

refer to SPECIFIC WARNINGS - STABILITY in

PROCEDURE 1 of this manual for additional

requirements.

After ANY adjustments, repair or service

and BEFORE use, make sure all attaching

hardware is tightened securely - otherwise

injury or damage may occur.

REMOVING/INSTALLING THE

REAR WHEELS

NOTE: To remove/install the rear wheels,refer to RE-

MOVING/INSTALLING REAR WHEELS in PROCE-

DURE 6 of the Owner's Manual, part number 1088909.

REPLACING SIX OR EIGHT-INCH

CASTER/FORK ASSEMBLY

(FIGURE 1)

1. Remove the dust cover.

2. Remove the locknut that secures the caster/fork as-

sembly to the caster headtube.

3. Drop the caster/fork assembly out of the caster

headtube.

FIGURE 1 - REPLACING SIX OR EIGHT-INCH

CASTER/FORK ASSEMBLY

Locknut

Dust Cover

Caster/Fork

Assembly

Caster

Headtube

FIGURE 2 - FRONT CASTER MOUNTING

ADJUSTMENTS

Washer

(if applicable)

Locknut

Front Caster

Fork

Mounting

Screw

FRONT CASTER MOUNTING

ADJUSTMENTS (FIGURE 2)

1. Remove the mounting screw, washers (if applicable)

and locknut that secure the front caster to the fork.

2. Reposition front caster on the fork to the determined

mounting hole by performing one (1) of the following:

A. PATRIOT - Refer to CHANGING SEAT-TO-

FLOOR HEIGHT/SEAT-TO-FLOOR ANGLE

in PROCEDURE 6 of this manual.

B. PATRIOT SL - Refer to CHANGING SEAT-TO-

FLOOR HEIGHT in PROCEDURE 7 of this

manual.

3. Secure front caster to fork with EXISTING mounting

screw, washers (if applicable), and locknut. Securely

tighten.

WARNING

Make sure both front casters are posi-

tioned in the same mounting hole BEFORE

using the wheelchair; otherwise injury

may result.

4. Repeat STEPS 1-3 for the opposite front caster.

5. Adjust the anti-tippers. Refer to INSTALLING/AD-

JUSTING THE ANTI-TIPPERS in PROCEDURE

7 of the Owner's Manual, part number 1088909.

4. Slide the NEW six or eight-inch caster/fork assembly

into the caster headtube.

5. Secure the NEW six or eight-inch caster/fork assem-

bly with the EXISTING locknut.

6. Adjust the caster/fork assembly. Refer to ADJUST-

ING FORKS in PROCEDURE 6 of the Owner's

Manual, part number 1088909.

7. Adjust the anti-tippers. Refer to INSTALLING/AD-

JUSTING THE ANTI-TIPPERS in PROCEDURE

7 of the Owner's Manual, part number 1088909.

14

WHEELS

W

H

E

L

S

PROCEDURE 5

Locknut

Washer

Cam

Caster Headtube

Coved

Spacers

Mounting Screw

Wheelchair

Frame

Locknut

Washer

Cam

Caster Headtube

Coved Spacers

Mounting Screw

Leading to Trailing (FIGURE 4)

1. Remove the two (2) mounting screws, four (4) coved

spacers, washer, cam and two (2) locknuts that se-

cure the caster headtube to the wheelchair frame.

2. Repeat STEP 1 for opposite side.

3. Position EXISTING RIGHT caster headtube onto LEFT

side of wheelchair frame as shown in FIGURE 4.

4. Secure the bottom of the EXISTING caster headtube

to the wheelchair frame using EXISTING hardware.

Refer to FIGURE 4 for proper hardware orientation.

5. The seat-to-floor angle must be adjusted by perform-

ing one (1) of the following:

A. PATRIOT - Refer to CHANGING SEAT-TO-

FLOOR HEIGHT/SEAT-TO-FLOOR ANGLE

in PROCEDURE 6 of this manual.

B. PATRIOT SL - Refer to CHANGING SEAT-TO-

FLOOR HEIGHT in PROCEDURE 7 of this

manual.

6. Secure the cam to the top of the caster headtube with

the EXISTING hardware. Refer to FIGURE 4 for cor-

rect hardware orientation.

7. Adjust the anti-tippers. Refer to INSTALLING/AD-

JUSTING THE ANTI-TIPPERS in PROCEDURE

7 of the Owner's Manual, part number 1088909.

FIGURE 3 - TRAILING TO LEADING

FIGURE 4 - LEADING TO TRAILING

Wheelchair

Frame

CONVERTING FROM TRAILING TO

LEADING OR LEADING TO

TRAILING CASTERS

Trailing to Leading (FIGURE 3)

1. Remove the two (2) mounting screws, four (4) coved

spacers, washer, cam and two (2) locknuts that se-

cure the caster headtube to the wheelchair frame.

2. Repeat STEP 1 for opposite side.

3. Position EXISTING RIGHT caster headtube onto LEFT

side of wheelchair frame as shown in FIGURE 3.

4. Loosely tighten the bottom of the EXISTING caster

headtube to the wheelchair frame using EXISTING

hardware. Refer to FIGURE 3 for proper hardware

orientation.

5. The seat-to-floor angle must be adjusted by perform-

ing one (1) of the following:

A. PATRIOT - Refer to CHANGING SEAT-TO-

FLOOR HEIGHT/SEAT-TO-FLOOR ANGLE

in PROCEDURE 6 of this manual.

B. PATRIOT SL - Refer to CHANGING SEAT-TO-

FLOOR HEIGHT in PROCEDURE 7 of this

manual.

6. Secure the cam to the top of the caster headtube with

the EXISTING hardware. Refer to FIGURE 3 for cor-

rect hardware orientation.

7. Securely tighten the caster headtube to the wheel-

chair frame.

8. Adjust the anti-tippers. Refer to INSTALLING/AD-

JUSTING THE ANTI-TIPPERS in PROCEDURE

7 of the Owner's Manual, part number 1088909.

REPOSITIONING/REPLACING CAM

(FIGURES 3 AND 4)

1. Do one (1) of the following:

A. TO REPOSITION - Refer to CHANGING SEAT-

TO-FLOOR HEIGHT/SEAT-TO-FLOOR ANGLE

in PROCEDURE 6 for the PATRIOT OR CHANG-

ING SEAT-TO-FLOOR HEIGHT in PROCE-

DURE 7 for the PATRIOT SL in this manual.

B. TO REPLACE - BEFORE removing the cam,

note position of the cam in the caster headtube

for proper reinstallation.

15

REPLACING THE WHEEL LOCKS

(FIGURE 5)

NOTE: BEFORE removing the wheel lock(s), note posi-

tion of wheel lock(s) on the wheelchair frame for proper

reinstallation.

1. Remove the mounting screw and washer that se-

cure the EXISTING wheel lock to the wheelchair frame.

2. Remove the EXISTING wheel lock from the wheelchair.

3. Install the NEW wheel lock to the wheelchair frame.

4. Secure the NEW wheel lock to the wheelchair frame

with the mounting screw and washer.

5. Repeat STEPS 1-4 for opposite side, if necessary.

6. Adjust the wheel locks. Refer to USING/ADJUST-

ING THE PATIENT OPERATED WHEEL LOCKS

in PROCEDURE 7 of the Owner's Manual, part num-

ber 1088909.

FIGURE 5 - REPLACING THE WHEEL LOCKS

W

H

E

L

S

WHEELS PROCEDURE 5

2. Remove the mounting screw, coved spacers, cam

and locknut that secure the EXISTING cam to the

caster headtube.

3. Loosen the bottom mounting screw, coved spacers

and locknuts that secure the caster headtube to the

wheelchair frame.

NOTE: Loosening the bottom mounting screw allows

the cam to be positioned easily in the caster headtube.

4. Remove the cam from the wheelchair.

5. Install the NEW/EXISTING cam at the position noted

in STEP 1. Refer to FIGURES 3 OR 4 for correct

hardware orientation.

6. Securely tighten the bottom mounting screw, coved

spacers and locknuts that secure the caster headtube

to the wheelchair frame.

Mounting

Screw

Washer

Wheelchair Frame

Wheel Lock

REPLACING THE HIGH MOUNT

WHEEL LOCKS (FIGURE 6)

NOTE: When using the 24-inch rear wheels the high mount

wheel lock will rest directly under the front arm socket.

NOTE: Note the position and orentation of the high mount

wheel locks and mounting hardware before removing.

1. Remove the two EXISTING (2) socket screws

the secure the EXISTING clamps and wheel lock

assembly to the wheel chair frame and discard.

2. Position the NEW clamps around the wheelchair

frame as shown in FIGURE 6.

3. Loosely tighten the two (2) NEW socket screws

that secure the NEW clamps to the wheelchair

frame.

4. Slide the NEW wheel lock assembly into the

clamps as shown in FIGURE 6.

5. Adjust the wheel locks. Refer to WHEEL LOCK AD-

JUSTMENT in PROCEDURE 7 of the Owner's

Manual, part number 1088233.

FIGURE 6 - REPLACING THE HIGH MOUNT

WHEEL LOCKS

Socket Screws

Wheel

Lock

Wheelchair

Frame

Clamps

16

2. Secure the NEW rear arm socket to the wheelchair

frame with the locknut.

3. Install the armrest onto the wheelchair. Refer to RE-

MOVING/INSTALLING FLIP BACK ARMREST in

PROCEDURE 4 of the Owner's Manual, part num-

ber 1088909.

Space Saver (FIGURE 2)

REMOVING.

1. Remove the armrest from the the wheelchair. Refer

to REMOVING/INSTALLING FLIP BACK ARM-

REST in PROCEDURE 4 of the Owner's Manual,

part number 1088909.

2. Remove the mounting screw, washer and locknut

that secure the EXISTING rear arm socket to the arm-

rest bracket.

3. Remove the EXISTING rear arm socket from the

wheelchair.

4. Do one (1) of the following:

A. Install the NEW rear arm socket to the wheel-

chair. Refer to INSTALLING REAR ARM

SOCKET in this procedure of the manual.

B. Convert the rear arm socket from space saver to

conventional. Refer to INSTALLING REAR ARM

SOCKET - CONVENTIONAL in this procedure

of the manual.

INSTALLING.

1. Install the mounting screw and washer through the

axle brackets and NEW rear arm socket as shown in

FIGURE 2.

2. Secure the NEW rear arm socket to the wheelchair

frame with the locknut.

3. Install the armrest onto the wheelchair. Refer to RE-

MOVING/INSTALLING FLIP BACK ARMREST in

PROCEDURE 4 of the Owner's Manual, part num-

ber 1088909.

Locknut

Spacer

Rear Arm Socket

Mounting

Screw

Wheelchair

Frame

FIGURE 1 - REMOVING/INSTALLING REAR ARM

SOCKET - CONVENTIONAL

PROCEDURE 6 PATRIOT

P

A

T

R

I

O

T

This Procedure Includes the Following:

Removing/Installing Rear Arm Socket

Replacing Armrest Bracket

Converting from Space Saver to Conventional OR

Conventional to Space Saver

Removing/Installing Axle Bracket

Converting from Standard Axle to Amputee

Changing Seat-to-Floor Height/

Seat-to-Floor Angle

WARNING

After ANY adjustments, repair or service

and BEFORE use, make sure all attaching

hardware is tightened securely - otherwise

injury or damage may occur.

REMOVING/INSTALLING REAR

ARM SOCKET

WARNING

The armrest bracket MUST be attached

to the wheelchair BEFORE using - other-

wise, injury or damage may result.

Conventional (FIGURE 1)

REMOVING.

1. Remove the armrest from the the wheelchair. Refer

to REMOVING/INSTALLING FLIP BACK ARM-

REST in PROCEDURE 4 of the Owner's Manual,

part number 1088909.

2. Remove the mounting screw, spacer and locknut that

secure the EXISTING rear arm socket to the armrest

bracket.

3. Remove the EXISTING rear arm socket from the

wheelchair.

4. Do one (1) of the following:

A. Install the NEW rear arm socket to the wheelchair.

Refer to INSTALLING REAR ARM SOCKET in

this procedure of the manual.

B. Convert the rear arm socket from conventional to

space saver. Refer to INSTALLING REAR ARM

SOCKET - SPACE SAVER in this procedure of

the manual.

INSTALLING.

1. Install the mounting screw through the NEW rear arm

socket, spacer, axle brackets and wheelchair frame

as shown in FIGURE 1.

17

FIGURE 2 - REMOVING/INSTALLING REAR ARM

SOCKET - SPACE SAVER

PROCEDURE 6PATRIOT

P

A

T

R

I

O

REPLACING ARMREST BRACKET

(FIGURE 3)

WARNING

The armrest bracket MUST be attached to

the wheelchair BEFORE using -otherwise,

injury or damage may result.

1. Remove the armrest from the the wheelchair. Refer

to REMOVING/INSTALLING FLIP BACK ARM-

REST in PROCEDURE 4 of the Owner's Manual,

part number 1088909.

2. Remove the REAR arm socket from the wheelchair.

Refer to REMOVING/INSTALLING REAR ARM

SOCKET in this procedure of the manual.

3. Remove the three (3) mounting screws, washers and

locknuts that secures the EXISTING armrest brack-

ets to the wheelchair frame.

4. Remove the EXISTING armrest brackets from the

wheelchair frame.

5. Install the EXISTING three (3) mounting screws, wash-

ers and NEW armrest brackets onto the wheelchair

frame as shown in FIGURE 3.

6. Securely tighten the NEW armrest brackets with the

three (3) locknuts. Torque to 50-60 in./lbs.

7. Install the REAR arm socket to the wheelchair frame.

Refer to REMOVING/INSTALLING REAR ARM

SOCKET in this procedure of the manual.

8. Install the armrest onto the wheelchair. Refer to RE-

MOVING/INSTALLING FLIP BACK ARMREST in

PROCEDURE 4 of the Owner's Manual, part num-

ber 1088909.

9. Repeat STEPS 1-8 for opposite side, if necessary.

CONVERTING FROM SPACE

SAVER TO CONVENTIONAL OR

CONVENTIONAL TO SPACE SAVER

Space Saver to Conventional (FIGURE 4)

1. Remove the rear wheels from the wheelchair. Refer

to REMOVING/INSTALLING REAR WHEELS in

PROCEDURE 6 of the Owner's Manual, part num-

ber 1088909.

2. Position the NEW spacer between the rear wheel

and the wheelchair frame.

3. Secure the rear wheel to the wheelchair frame using

the NEW permanent axle, spacer and EXISTING lock-

nut as shown in FIGURE 4. Torque to 20-40 ft./lbs.

4. Repeat STEPS 2-3 for opposite side of wheelchair.

5. Remove the armrest from the wheelchair. Refer to

REMOVING/INSTALLING FLIP BACK ARMREST

in PROCEDURE 4 of the Owner's Manual, part num-

ber 1088909.

6. Remove the mounting screw, washer and locknut

that secure the rear arm socket to the wheelchair

frame.

NOTE: The washer will NOT be reused.

7. Remove the rear arm socket from the wheelchair.

8. Position the NEW spacer between the two (2) arm-

rest brackets and the rear arm socket on the outside

of the wheelchair frame.

9. Secure the rear arm socket and NEW spacer to the

wheelchair frame with the EXISTING mounting screw

and locknut.

10. Install the armrest onto the wheelchair. Refer to RE-

MOVING/INSTALLING FLIP BACK ARMREST in

PROCEDURE 4 of the Owner's Manual, part num-

ber 1088909.

11. Repeat STEPS 5-10 for opposite side of wheelchair.

Mounting

Screw

Rear Arm

Socket

FIGURE 3 - REPLACING ARMREST BRACKET

Mounting

Screw

Armrest Brackets

Wheelchair

Frame

Locknut

Wheelchair

Frame

Locknut

Washer

18

9. Install the armrest onto the wheelchair. Refer to RE-

MOVING/INSTALLING FLIP BACK ARMREST in

PROCEDURE 4 of the Owner's Manual, part num-

ber 1088909.

10. Repeat STEPS 4-9 for opposite side.

FIGURE 5 - CONVERTING FROM

CONVENTIONAL TO SPACE SAVER

Conventional to Space Saver (FIGURE 5)

1. Remove the rear wheels from the wheelchair. Refer

to REMOVING/INSTALLING REAR WHEELS in

PROCEDURE 7 of the Owner's Manual, part num-

ber 1088909.

2. Remove the two (2) spacers between the rear wheels

and the wheelchair frame.

NOTE: The two (2) spacers will NOT be reused.

3. Secure the rear wheels to the wheelchair frame us-

ing the NEW permanent axle. Torque to 20-40 ft./lbs.

4. Remove the armrest from the wheelchair. Refer to

REMOVING/INSTALLING FLIP BACK ARMREST

in PROCEDURE 4 of the Owner's Manual, part num-

ber 1088909.

5. Remove the mounting screw, spacer and locknut that

secure the rear arm socket to the wheelchair frame.

6. Remove the rear arm socket and spacer from the

wheelchair.

NOTE: The spacer will NOT be reused.

7. Position the rear arm socket between the armrest

brackets as shown in FIGURE 5.

8. Secure the rear arm socket to the wheelchair using

the EXISTING mounting screw, NEW washer and

locknut.

Locknut

NEW

Spacer

Rear Arm

Socket

Mounting

Screw

Outside of

Wheelchair

Frame

FIGURE 4 - CONVERTING FROM SPACE SAVER TO

CONVENTIONAL

PROCEDURE 6 PATRIOT

Wheelchair Frame

Spacer

Rear Wheel

Washer

Dust

Cap

Permanent

Axle

P

A

T

R

I

O

T

Wheelchair Frame

Spacer

Rear Wheel

Washer

Dust

Cap

Permanent

Axle

STEPS 2-4

STEPS 7-10

STEPS 2-3

REMOVING/INSTALLING AXLE

BRACKET (FIGURE 6)

WARNING

BEFORE performing this procedure, refer to

SPECIFIC WARNINGS - STABILITY in PROCEDURE

1 of this manual for additional requirements.

Removing

1. Remove the rear wheel from the wheelchair. Refer to

REMOVING/INSTALLING REAR WHEELS in

PROCEDURE 6 of the Owner's Manual, part num-

ber 1088909.

2. Remove the two (2) mounting screws and locknuts

that secure the EXISTING axle bracket to the wheel-

chair frame.

3. Repeat STEPS 1-2 for opposite side, if necessary.

4. Install the NEW/EXISTING axle bracket to the wheel-

chair frame. Refer to INSTALLING in this procedure

of the manual.

Mounting

Screw

Rear Arm

Socket

Wheelchair

Frame

Locknut

Washer

STEPS 6-9

19

CHANGING SEAT-TO-FLOOR

HEIGHT/SEAT-TO-FLOOR ANGLE

WARNING

DO NOT deviate from the charts on the

following pages. There are restrictions for

seat-to-floor heights and seat-to-floor

angles that will cause the wheelchair to

be in an unsafe position. BEFORE chang-

ing, refer to the following for the allow-

able positions.

The different Seat-to-Floor Heights and angles are pos-

sible by using different combinations of REAR WHEELS,

REAR WHEEL POSITION, FRONT CASTER POSI-

TION, CASTER SIZE AND CAM POSITION.

NOTE: Refer to the charts on the following pages for the

correct settings for the desired Seat-to-Floor Height and

Seat-to-Floor angle.

After determining rear wheel size and rear wheel posi-

tion, refer to REMOVING/INSTALLING REAR

WHEELS in PROCEDURE 6 of the Owner's Manual,

part number 1088909.

After determining caster size and caster position needed,

refer to REPLACING SIX OR EIGHT-INCH CASTER/

FORK ASSEMBLY in PROCEDURE 5 of this manual.

After determiming seat-to-floor angle, refer to REPOSI-

TIONING/REPLACING CAM in PROCEDURE 5 of this

manual.

Adjust the wheel locks. Refer to USING/ADJUSTING

THE PATIENT OPERATED WHEEL LOCKS in PRO-

CEDURE 7 of the Owner's Manual, part number 1088909.

WARNING

After changing Seat-to-Floor Height and/

or Seat-to-Floor Angle, the anti-tippers MUST

be replaced or adjusted BEFORE using the

wheelchair. Refer to INSTALLING/ADJUST-

ING THE ANTI-TIPPERS in PROCEDURE 7 of

the Owner's Manual, part number 1088909.

Seat

-to-

Floor

Seat

Angle

Installing

1. Position the NEW/EXISTING axle bracket onto the

wheelchair frame.

2. Secure the NEW/EXISTING axle bracket to the

wheelchair frame with the EXISTING mounting

screws and locknuts as shown in FIGURE 6.

Torque to 50-60 in./lbs.

3. Repeat STEPS1-2 for opposite side, if necessary.

4. Install the rear wheel from the wheelchair. Refer to

REMOVING/INSTALLING REAR WHEELS in

PROCEDURE 6 of the Owner's Manual, part num-

ber 1088909.

CONVERTING FROM STANDARD

AXLE TO AMPUTEE

WARNING

BEFORE performing this procedure, refer to

SPECIFIC WARNINGS - STABILITY in PROCEDURE

1 of this manual for additional requirements.

1. Remove the axle bracket from the wheelchair. Refer

to REMOVING/INSTALLING AXLE BRACKET in

this procedure of the manual.

2. Determine the desired seat-to-floor height. Refer to

the charts in CHANGING SEAT-TO-FLOOR

HEIGHT in this procedure for corresponding axle

bracket positioning for desired seat-to-floor height.

3. Install the axle bracket Refer to REMOVING/IN-

STALLING AXLE BRACKET in this procedure of

the manual.

4. Adjust the wheel locks. Refer to USING/ADJUST-

ING THE PATIENT OPERATED WHEEL LOCKS

in PROCEDURE 7 of the Owner's Manual, part num-

ber 1088909.

5. Adjust the anti-tippers. Refer to INSTALLING/AD-

JUSTING THE ANTI-TIPPERS in PROCEDURE

7 of the Owner's Manual, part number 1088909.

PROCEDURE 6PATRIOT

FIGURE 6 - REMOVING/INSTALLING AXLE

BRACKET

P

A

T

R

I

O

T

Mounting Screw

Locknut

Axle Bracket

Wheelchair

Frame

20

Caster Headtube, Front Caster, Axle Mounting Bracket Positioning and Cam Position for

24-inch Rear Wheels and 8-inch Front Casters (FIGURES 1 - 7)

*WARNING

If changing the seat-to-floor angle to 6

o

,

anti-tippers MUST be installed.

Refer to the following chart to determine the obtainable seat-to-floor height and seat angle combina-

tions for 24-inch rear wheels and 8-inch front casters:

SEAT-TO-FLOOR SEAT ANGLE

HEIGHT OF WITH A OF FIGURE

19-1/2-inches 3

o

Refer to FIGURE 1

19-1/2-inches *6

o

Refer to FIGURE 2

18-1/2-inches 0

o

Refer to FIGURE 3

18-1/2-inches 3

o

Refer to FIGURE 4

18-1/2-inches *6

o

Refer to FIGURE 5

17-1/2-inches 0

o

Refer to FIGURE 6

17-1/2-inches 3

o

Refer to FIGURE 7

AXLE MOUNTING BRACKET CASTER HEADTUBE FRONT CASTER CAM POSITION

FORWARD REARWARD

(STANDARD) (AMPUTEE) LEADING TRAILING

Notch

FIGURE 1 - SEAT-TO-FLOOR HEIGHT OF 19-1/2-INCHES AND A SEAT ANGLE OF 3

0

FIGURE 2 - SEAT-TO-FLOOR HEIGHT OF 19-1/2-INCHES AND A SEAT ANGLE OF 6

0

Notch

FIGURE 3 - SEAT-TO-FLOOR HEIGHT OF 18-1/2-INCHES AND A SEAT ANGLE OF 0

0

PROCEDURE 6 PATRIOT

P

A

T

R

I

O

T

AXLE MOUNTING BRACKET CASTER HEADTUBE FRONT CASTER CAM POSITION

FORWARD REARWARD

(STANDARD) (AMPUTEE) LEADING TRAILING

AXLE MOUNTING BRACKET CASTER HEADTUBE FRONT CASTER CAM POSITION

FORWARD REARWARD

(STANDARD) (AMPUTEE) LEADING TRAILING

Notch

Page is loading ...

Invacare Patriot, Patriot SL User manual

Related papers

Other documents