Alarm Lock Trilogy ET-PDL Sargent 8812 Instructions & Template

Alarm Lock
Brand
Alarm Lock
Model
Trilogy ET-PDL Sargent 8812
Type
Instructions & Template

Alarm Lock Trilogy ET-PDL Sargent 8812 is a panic exit device trim that can be used to upgrade your existing Sargent 8812 exit device to include battery backup. This will allow the exit device to continue to function in the event of a power outage.

The ET-PDL trim includes a battery box, battery pack, and mounting plate. The battery box is mounted below the exit device and the battery pack is inserted into the battery box. The mounting plate is used to secure the ET-PDL trim to the exit device.

To install the ET-PDL trim, you will need to remove the existing exit device from the door, position the ET-PDL trim on the door, and drill the required holes. Once the holes are drilled, you can secure the ET-PDL trim to the exit device and the door.

Alarm Lock Trilogy ET-PDL Sargent 8812 is a panic exit device trim that can be used to upgrade your existing Sargent 8812 exit device to include battery backup. This will allow the exit device to continue to function in the event of a power outage.

The ET-PDL trim includes a battery box, battery pack, and mounting plate. The battery box is mounted below the exit device and the battery pack is inserted into the battery box. The mounting plate is used to secure the ET-PDL trim to the exit device.

To install the ET-PDL trim, you will need to remove the existing exit device from the door, position the ET-PDL trim on the door, and drill the required holes. Once the holes are drilled, you can secure the ET-PDL trim to the exit device and the door.

IMPORTANT
Templates must be printed without size modifications
and verified for dimensional accuracy.
• Before printing, select the printing options necessary
to ensure that copies are produced without size
adjustments.
• After printing, measure the dimensions indicated on
the template to ensure correct scale.
ET-PDL
Trilogy ® Panic Exit Device Trim
INSTRUCTIONS & TEMPLATE
Sargent
Model 8812
Rim Exit Device
N
E
W
To Change Cylinder
Alarm Lock Systems, Inc.
A division of the NAPCO Security Group
345 Bayview Avenue, Amityville, NY 11701
Tel: (631) 789-4871 Fax: (631) 789-3383
www.alarmlock.com
Publicly traded on NASDAQ Symbol: NSSC
1. Existing Installation: Remove Exit device from door.
2. Existing Installation: Position Alarm Lock template on
horizontal & vertical lines of existing spindle hole.
New Installation: Locate and mark horizontal and vertical
lines indicated in Exit Device Instructions/Template. Line up
Alarm Lock template with horizontal and vertical lines and
tape on door.
Existing and New Installations: Mark all hole centers on
each side of door. Drill all holes from both sides of door to
avoid splintering.
3. Position Exterior assembly on door.
4. Replace Exit Device, insert and fasten with 2 new Shoulder
mounting screws, on top of Exit Device into mounting posts.
Fasten two #10 x 1-1/4" flat head sheet metal screws in
lower mounting holes. Do not over-tighten. Pull wires from
door through Battery Mounting Plate. Do not pinch or cut
wires. Position plate below Exit Device and fasten with two
Shoulder screws on top, into mounting posts and two #8 x
3/4" flat head sheet metal screws on the bottom.
5. Connect battery pack and place inside of battery mounting
plate. Position cover and fasten with three #6-32 x 5/16"
screws.
6. Replace and fasten Exit device & Battery box covers.
Check lock for proper operation
before closing door.
A. Remove Cover plate. Rotate the
spindle either direction to expose
and remove cylinder screws.
B. Remove old cylinder and insert new cylinder.
C. Note: The tailpiece must be in the
horizontal position as shown in the
image above.
ETDL
SERIES
ETPDL
SERIES
1
3
5
6
A
B
C
TailPiece
IMPORTANT:
When replacing cylinder
be sure to use the
proper Cylinder Adapter
and Tailpiece.
© ALARM LOCK 2007
WI 1121A-NS8 10/07
VERTICAL LINE
1.850"
4.920"
TWO
THRU-
BOLT
HOLES
5/16"
DRILL BOTH
SIDES
Sargent
Model 8812
SPINDLE
HOLE
1"
MINIMUM
DRILL BOTH
SIDES
RECOMMENDED
HORIZONTAL
LINE OF
EXIT DEVICE
4.025"
1.532"
1.375"
TWO HOLES
INTERIOR ONLY
FOR EXIT DEVICE
INSTALLATION
Drill 3/32" hole
1-1/4" deep for
#10 flat head
sheet metal
screws
TWO THRU-
BOLT HOLES
(FOR BATTERY
MOUNTING
PLATE)
5/16"
DRILL BOTH
SIDES
WIRES
HOLE
1/2"
DRILL BOTH
SIDES
4.840"
1.532"
6.690"
Battery
Box Cover
Battery
Pack
Battery Box
Mounting Plate
4
Two #10 x 1¼"
flat head self-
tapping screws
Two Shoulder
mounting screws
Two Shoulder
mounting screws
Two #8 x 3/4"
flat head sheet
metal screws
2
Note: The
spindle
hole must
be no less
than 1"
diameter
  • Page 1 1
  • Page 2 2

Alarm Lock Trilogy ET-PDL Sargent 8812 Instructions & Template

Alarm Lock
Brand
Alarm Lock
Model
Trilogy ET-PDL Sargent 8812
Type
Instructions & Template

Alarm Lock Trilogy ET-PDL Sargent 8812 is a panic exit device trim that can be used to upgrade your existing Sargent 8812 exit device to include battery backup. This will allow the exit device to continue to function in the event of a power outage.

The ET-PDL trim includes a battery box, battery pack, and mounting plate. The battery box is mounted below the exit device and the battery pack is inserted into the battery box. The mounting plate is used to secure the ET-PDL trim to the exit device.

To install the ET-PDL trim, you will need to remove the existing exit device from the door, position the ET-PDL trim on the door, and drill the required holes. Once the holes are drilled, you can secure the ET-PDL trim to the exit device and the door.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents