Tripp Lite SmartOnline SU5000RT4U User manual

Tripp Lite
Brand
Tripp Lite
Model
SmartOnline SU5000RT4U
Category
Uninterruptible power supplies (UPSs)
Type
User manual
Owner’s Manual
WARRANTY
REGISTRATION:
register online today for a
chance to win a FREE Tripp Lite
product—www.tripplite.com/warranty
SmartOnline
™
Hot-Swappable Modular
Intelligent True On-Line UPS Systems
Models: SU5000RT4U, SU6000RT4U and SU8000RT4U
Not suitable for mobile applications.
Important Safety Warnings
2
Features
3
Mounting
5
Connection
6
Optional Connection
7
Manual Bypass Operation
9
Operation
11
Internal Battery Replacement
16
Storage/Service
16
Warranty/Warranty Registration
17
1111 W. 35th Street, Chicago, IL 60609 USA
www.tripplite.com/support
Copyright © 2011 Tripp Lite. All rights reserved. SmartOnline™ is a trademark of Tripp Lite.
Español
18
Français
35
201102170 932611.indd 1 3/30/2011 10:22:08 AM
2
Important Safety Warnings
SAVE THESE INSTRUCTIONS. This manual contains important instructions and warnings that should be
followed during the installation and maintenance of this UPS System. Failure to heed these warnings may
affect your warranty.
UPS Location Warnings
• TheUPSisextremelyheavy.Usecautionwhenliftingandinstalling.
• InstallyourUPSindoors,awayfromexcessmoistureorheat,directsunlight,dustandconductivecontaminants.
• InstallyourUPSinastructurallysoundarea.
• OnlyoperateyourUPSatindoortemperaturesbetween32°Fand104°F(between0°Cand40°C).Forbestresults,keepindoor
temperaturesbetween62°Fand84°F(between17°Cand29°C).
• LeaveadequatespacearoundallsidesoftheUPSforproperventilation.Donotobstructitsventilationfansoropenings.
• DonotinstalltheUPSnearmagneticstoragemedia,asthismayresultindatacorruption.
• Do not mount unit with its front or rear panel facing down (at any angle). Mounting in this manner will seriously inhibit the
unit's internal cooling, eventually causing product damage not covered under warranty.
UPS Connection Warnings
• Thepowersupplyforthisunitmustbesplit-phaseratedinaccordancewiththeequipmentnameplate.Italsomustbesuitablygrounded.
• ConnectyourUPSsystemonlytoafour-wireinputpowerconnection(L1,L2,N,G).ThisUPSrequiresaninputneutralconnection.
• ConnectyourUPStoaproperlygroundedACpoweroutlet.DonotmodifytheUPS'spluginawaythatwouldeliminatetheUPS's
connectiontoground.(Note: Model SU8000RT4U has a hardwire input instead of an input cord/plug.)
• DonotuseadaptersthateliminatetheUPS'sconnectiontoground.
• DonotplugyourUPSintoitself;thiswilldamagetheUPSandmayaffectyourwarranty.
• IfyouareconnectingyourUPStoamotor-poweredACgenerator,thegeneratormustprovidefiltered,frequency-regulated
computer-gradeoutput.ConnectingyourUPStoageneratormayaffectitsUltimateLifetimeInsurance.
Equipment Connection Warnings
• Useofthisequipmentinlifesupportapplicationswherefailureofthisequipmentcanreasonablybeexpectedtocausethefailureofthe
lifesupportequipmentortosignificantlyaffectitssafetyoreffectivenessisnotrecommended.Donotusethisequipmentinthepresence
ofaflammableanestheticmixturewithair,oxygenornitrousoxide
• TheUPScontainsaninternalDCenergysource(battery).TheoutputterminalsmaybeliveevenwhentheUPSisnotconnectedtoan
ACpowersource.
• DonotconnectsurgesuppressorsorextensioncordstotheoutputofyourUPS.ThismightdamagetheUPSandmayaffectthesurge
suppressorandUPSwarranties.
Maintenance Warnings
• YourUPSdoesnotrequireroutinemaintenance.DonotopentheUPSforanyreason.Therearenouser-serviceablepartsinside.
Battery Warnings
• TheinternalbatteriesinyourUPSarerecyclable.Refertolocalcodesfordisposalrequirements,orifintheUSAcall1-800-SAV-LEAD
(1-800-728-5323)forcompleterecyclinginformation.CAUTION:Donotdisposeofthebatteriesinafire,asthiscouldcausethebattery
toexplode.
• Batteriescanpresentariskofelectricalshockandburnfromhighshort-circuitcurrent.Observeproperprecautions.Donotdisposeofthe
batteriesinafire.DonotopentheUPSorbatteries.Donotshortorbridgethebatteryterminalswithanyobject.Unplugandturnoffthe
UPSbeforeperformingbatteryreplacement.Usetoolswithinsulatedhandles.Therearenouser-serviceablepartsinsidetheUPS.Battery
replacementshouldbeperformedonlybyauthorizedservicepersonnelusingthesamenumberandtypeofbatteries(SealedLead-Acid).
Thebatteriesarerecyclable.RefertoyourlocalcodesfordisposalrequirementsorintheUSAonlycall1-800-SAV-LEADor
1-800-8-BATTERY(1-800-822-8837)orvisitwww.rbrc.comforrecyclinginformation.TrippLiteoffersacompletelineofUPSSystem
ReplacementBatteryCartridges(R.B.C.).VisitTrippLiteontheWebatwww.tripplite.com/support/battery/index.cfmtolocatethe
specificreplacementbatteryforyourUPS.
• Donotopenormutilatethebatteries.Releasedelectrolyteisharmfultotheskinandeyes,andmaybetoxic.
• Fusesshouldbereplacedonlybyfactory-authorizedpersonnel.Blownfusesshouldbereplacedonlywithfusesofthesamenumberandtype.
• Serviceandrepairshouldbedoneonlybytrainedpersonnel.DuringanyserviceworktotheUPS,itshouldbeturnedoff.Notethat
potentiallylethalvoltagesexistwithinthisunitaslongasthebatterysupplyisconnected.
• Donotconnectordisconnectexternalbatterypack(s)whiletheUPSisoperatingfromthebattery.
• Duringhot-swapbatteryreplacement,theUPSwillnotprovidebackuppowerintheeventofablackoutorotherpowerinterruptions.
• DonotoperateUPSwithoutbatteries.
• Whenaddingexternalbatterypackstomodelswithexternalbatterypackconnectors,connectonlyTrippLite-recommendedbatterypacks
ofthecorrectvoltageandtype.
201102170 932611.indd 2 3/30/2011 10:22:09 AM
3
Features
Front Panel Controls
I/P BYPASS
BATTERYAC/DC DC/AC O/P
OFFON
MUTE SELECT
SETUP
LCD Display:ThisbacklitdotmatrixdisplayindicatesawiderangeofUPSoperatingconditionsanddiagnosticdata.Italsodisplays
UPSsettingsandoptionswhentheUPSisinsetupmode.
“ON/MUTE” Button:PressthisbuttonandholdituntilyouhearabeeptoturntheUPSsystem'sinverterON.IftheUPS'sbattery
alarmissounding,pressthisbuttontosilenceit.
Scroll Down Button:ThisbuttonallowsyoutobrowsethroughdifferentoptionsandpowerreadingsontheLCDdisplay.Momentarily
pressingitcausestheLCDscreentodisplayadifferentpowerreading(see“Operation”section).PressingitandtheSCROLLUPButton
togetherputstheUPSinsetupmode,wherethisbuttonisusedtoscrollthroughsetupoptionsandtoexitsetupmode.Pressingthe
SCROLLUPandSCROLLDOWNbuttonssimultaneouslyforlongerthanonesecondwhiletheUPSisin"ONBATTERYMODE"
allowsyoutochangetheoutputvoltageoftheUPS(referto"OutputVoltageSelection"inthe"Operation"sectionfordetails).
Scroll Up/“SELECT” Button:ThisbuttonallowsyoutobrowsethroughdifferentoptionsandpowerreadingsontheLCDdisplay.
MomentarilypressingitcausestheLCDscreentodisplayadifferentpowerreading(see"Operation"section).PressingtheSCROLLUP
ButtonandSCROLLDOWNButtonatthesametimeprovidesaccesstotheconfigurationoptionsoftheUPSwhichincludeenablingor
disablingtheUPS"EconomyMode"featureorchangingtheoutputvoltageoftheUPS.(Referto"ConfigurationMenu"inthe
"Operation"sectionfordetails.)
“OFF” Button:Pressthisbuttonandholdituntilyouhearabeep.TheUPSwilldisplaythefollowingmessage:"SwitchtoBypass
N(ON)/Y(OFF)"ifitissafetodoso.PressingOFFagainwillputtheUPSinBypass,stillprovidingpowertoanyconnectedequipment,
butwillnotsupportalossofutilitypower.
“O/P” (Output) LED:ThisgreenlightwillilluminatetoindicateyourUPSissupplyingACpowertoconnectedequipment.
“DC/AC” (Inverter) LED:ThisgreenlightwillilluminatetoindicatetheUPS'sDC/ACinverterisactivated.
“BYPASS” LED:TheBYPASSLEDwillilluminateasolidamberwhentheUPSisrunninginEconomyModeorflashamberifthe
UPSisinaBYPASSstate.ThisamberlightwillflashwhentheUPSisprovidingfilteredmainspowerwithoutengagingitsconverteror
inverter.IfthisLEDisflashing,connectedequipmentwillnotreceivebatterypowerintheeventofablackout.
“AC/DC” (Converter) LED:ThisgreenlightwillilluminatetoindicatetheUPS'sAC/DCconverterischargingtheconnectedbattery
pack(s).
“BATTERY” LED:ThisredlightwillilluminatewhentheUPSisdischargingthebatterytoprovideconnectedequipmentwithAC
power.AnalarmwillsoundwhichcanbesilencedbypressingtheON/MUTEButton.ThisLEDwillremainlitafterthealarmissilenced.
“I/P” (Input) LED:ThisgreenlightwillilluminatetoindicateanACinputsupplyispresent.
Access Slots:Torotatethecontrols,insertaflatheadscrewdriverintotheseslotsandgentlyleverthepanelout.Takingcarenottoexcessively
twistoryankthecablesconnectingthecontrolstotherestoftheUPS,turnthecontrolstothedesiredorientationandreinsertthem.
1
2
3
4
5
6
7
8
9
10
11
12
1
2
3
4
5
6
7
8
9
10
11
12
12
201102170 932611.indd 3 3/30/2011 10:22:09 AM
1
2
3
4
5
5
6
7
8
9
9
10
10
11
12
10
SU6000RT4U Shown (Rear View)
4
Features (continued)
Rear Panel Features (Power/Battery Module and Detachable PDU Together)
Power/Battery Module: Thisself-containedunithousestheUPSsystem'spowerandcontrolcomponentsaswellasitsinternalbatteries.
Independent, Detachable Power Distribution Unit (PDU): Thisself-containedunithousestheUPSsystem'sinputandoutputcomponents
alongwithabypassswitch.Whentheswitchissettobypass,thePDUcanbecompletelyremovedfromthepower/batterymodulefor
routinepower/batterymodulemaintenancewithoutdisruptingpowertoconnectedloads.WhilethisswitchissettoBYPASS,connected
equipmentwillreceiveunfilteredACmainspower,buttheequipmentwillnotreceivebatterypowerintheeventofablackout.Anoptional
hardwiredetachablePDUisalsoavailableseparatelyfromTrippLite.ContactTrippLitefordetails.Note:Therotarybypassswitchshould
onlybeoperatedwhiletheUPSisinBYPASSMode.(Seesection“ManualBypassOperation”onpage8fordetails.)
External Battery Connector:AlthoughtheUPSincludesarobustsetofinternalbatteries,youmaywanttousethisconnectortoattach
oneormoreoptionalexternalbatterypacks(availableseparatelyfromTrippLite)totheUPSforextendedruntime.Checktoensurethat
theexternalbatteriesyouareconnectingmatchthevoltagelistedonyourUPS'sbatteryconnector.Addingexternalbatterieswill
increaserechargetimeaswellasruntime.Seethebatterypackowner'smanualforcompleteinstallationinstructions.Makesurecables
arefullyinsertedintotheirconnectors.Smallsparksmayresultduringbatteryconnection;thisisnormal.Donotconnectordisconnect
batterypackswhentheUPSisrunningonbatterypower.
Battery Charge Level Switch (Select Models Only): ControlstheUPSsystem'sbatterychargerate.Ifyouconnectanyexternal
batteries,settheBatteryChargeLevelSwitchtotheright(labeled“EXTERNALBATTERIES”).ThiswillincreaseyourUPS'scharger
outputsotheadditionalbatterieschargefaster.CAUTION!DONOTsettheBatteryChargeLevelSwitchtotheright(labeled
“EXTERNALBATTERIES”)withoutanexternalbatteryconnected.ThereisariskofdamagingtheUPS'sinternalbatterysystem.
Ventilation Fans:ThesefanscoolandventilatetheinsideoftheUPS.
USB and RS-232 Communication Ports:TheseUSBandfemaleRS-232DB9serialportsmaybeusedtoconnectyourUPStoa
workstationorserver.TheyareusedwithTrippLitesoftwareandtheincludedUSBorserialcabletomonitorandmanagetheUPS
remotelyoveranetworkandtoautomaticallysaveopenfilesandshutdownequipmentduringablackout.See“OptionalConnection”
for details.
EPO (Emergency Power Off) Port:Thisportmaybeusedtoconnectthepowermoduletoacontactclosureswitchtoenable
emergencypoweroff.See“OptionalConnection”sectionfordetails.
Accessory Slot:Removetheslot'scovertoinstallanoptionalinternalSNMP/Webaccessorycard(Model:SNMPWEBCARD)toenable
remoteUPSmonitoringandcontrolviaSNMP,Webortelnet.VisitTrippLiteontheWeb(www.tripplite.com)tolearnaboutavailable
SNMP,networkmanagementandconnectivityproductsthatmaybeinstalledinthisslot.
AC Output Breakers:Thesebreakerscontroloutputpowerfromtheindependent,detachablePDU.
AC Receptacles:YourUPSfeatures15-,20-and30-ampACoutlets.Theseoutputreceptaclesprovideyourconnectedequipmentwith
AClinepowerduringnormaloperationandbatterypowerduringblackoutsandseverebrownoutsandovervoltages.TheUPSprotects
equipmentconnectedtothesereceptaclesagainstdamagingsurgesandlinenoise.IfyouhaveaserialorUSBconnectiontoyourUPS,
youcanremotelyrebootconnectedequipmentbyturningthereceptaclesOFFandONusingTrippLite'sPowerAlertSoftware.See
softwareinstructionsfordetails.
AC Input:ConnectstheUPSsystemtoautilitywalloutlet.YourUPSmustbeconnectedtoadedicatedcircuitofsufficientamperage.
Note: Model SU8000RT4U has a hardwire input instead of an input cord/plug
Maintenance Bypass Switch:ThisswitchallowsqualifiedservicepersonneltoremovethedetachablePDUfromthepower/battery
moduleforroutinemaintenancewithoutdisruptingpowertoconnectedloads.WhilethisswitchissettoBYPASS,connectedequipment
willreceivefilteredACmainspower,buttheequipmentwillnotreceivebatterypowerintheeventofablackout.See“ManualBypass
Operation”sectionforcompletebypassprocedure.
WARNING! For qualified service personnel only. Failure to follow the bypass procedure completely (see Manual Bypass
Operation section) will not adequately power down the UPS power/battery module, resulting in the continued risk of death or
injury from potential contact with high voltage.
1
2
3
4
5
6
7
8
9
10
11
12
201102170 932611.indd 4 3/30/2011 10:22:10 AM
Mounting (Tower)
MounttheUPSsysteminanupright,towerpositionusing2-9USTANDbasestands(optional).Theusermustdeterminethefitnessofhardware
andproceduresbeforemounting.
WARNING! The UPS system is extremely heavy. Use caution when lifting and mounting. User must properly stabilize the UPS when
lifting and mounting.
Adjust the stands to a width of 6.93
inches(176mm)foraUPS.Adjustthe
standstoawidthof12.07inches(306.5
mm)foraUPSandanexternalbattery
module.Alignthestandsapproximately
10inches(254mm)apart.Haveoneor
moreassistantshelpyouplacetheUPS
onitssideinthestands.PlacetheUPS
so that its control panel is on top and
facingoutward.
RotatetheUPS'scontrolpaneltoview
iteasierwhiletheUPSistowermounted.
Insertasmallscrewdriver,orothertool,
intheslotsoneithersideofthecontrol
panel.Popthepanelout;rotateit;and
popthepanelbackintoplace.
5
Mounting
3
2
1
4
1
2
1 Power Module
6.93" (176 mm)
1 Power Module +
1 Battery Module
12.07" (306.5 mm)
1 Power Module
6.93" (176 mm)
1 Power Module +
1 Battery Module
12.07" (306.5 mm)
1
1
I/P BYPASS
BATTERY AC/DC DC/AC
O/P
OFF
ON
MUTE
SELECT
SETUP
2
Mounting (4-Post Rackmount)
TheUPSincludesrackmountrailsfor4-postrackmounting.Theusermustdeterminethefitnessofhardwareandproceduresbeforemounting.
Ifhardwareandproceduresarenotsuitableforyourapplication,contactthemanufacturerofyourrackorrackenclosure.Theprocedures
describedinthismanualareforcommonrackandrackenclosuretypesandmaynotbeappropriateforallapplications.
WARNING! The UPS system is extremely heavy. Use caution when lifting and mounting. User must properly stabilize the UPS when
lifting and mounting.
Connectthetwosegmentsofeachshelf
usingtheincludedattachedscrewsand
wing nuts. Leave the screws slightly
loosesothattheshelvescanbeadjusted
inthenextstep.
Adjusteachshelftofityourrack,then
mount them in the lowest available
spaceofyourrackwiththescrews,nuts
and washers provided. Note that the
support ledges should face inward.
Tighten the wingnuts that connect the
shelf segments.
Attach mounting ears to the front
mountingholesofyourUPSusingthe
screws provided. The ears should face
forward.
Using one or moreassistants,lift your
UPS and slide it onto the mounting
shelves.AttachyourUPStotherackby
passingscrews,nutsandwashers(user-
provided)throughitsmountingearsand
intotherackrails.
Mounting (2-Post Rackmount)
If you mount this UPS model in 2-post racks, it requires the addition of a Tripp Lite 2-Post Rackmount Installation Kit (model:
2POSTRMKITWM,soldseparately).SeeInstallationKitowner'smanualforinstallationprocedure.
1
2
3
4
201102170 932611.indd 5 3/30/2011 10:22:11 AM
6
Connection
Model SU8000RT4U has a hardwire input instead of an input cord/plug.
Remove the circular knockouts to route the input cabling to the AC input
terminal block. Unscrew and remove the utility input terminal block cover
to access the AC input terminals. Review the hardwiring cautions below
before attempting to connect the UPS input.
Hardwiring Cautions (Model SU8000RT4U Only)
• Wiringmustbedonebyaqualifiedelectrician.
• When making wiring connections, observe the cable connection regulations
appropriatetoyourarea [e.g.NationalElectricalCode(NEC)in theU.S.]atall
times.Besuretoinstallaneasilyaccessibledisconnectswitchinyourinstallation
wiring so you may cut off the AC input of the UPS during fires and other
emergencies.Ensurethatcables are fittedwithcablesleevesandaresecuredby
connectorclamps.Tightenconnectionswithatorqueofnotlessthan24-28inch-
pounds(2.7-3.2NM).
• Makesurethatyourequipmentisproperlygrounded.
• Usingcablesofimpropersizemaydamageyourequipmentandcausefirehazards.
Choose appropriate cabling and protection circuits to make wiring connections.
Groundconductorsmustbethesamesizeandtypeasthepowerconductorsused.
• Refer to National Electrical Code (NEC) guidelines for proper wire gauge and
outputprotectioncircuitrequirements.
Plug your equipment into your UPS.
YourUPSisdesignedtosupportelectronicequipmentonly.YouwilloverloadyourUPS
if the total VA rating for all the equipment you connect exceeds the UPS's Output
Capacity.DonotconnecthouseholdappliancesorlaserprinterstotheUPS'soutlets.To
findyourequipment'sVAratings,lookontheirnameplates.Iftheequipmentislistedin
amps, multiply the number of amps by the input voltage (208V, 240V or 120V) to
determineVA.(Example:1amp×120V=120VA).
Turn the UPS on.
PresstheUPS's“ON”Button
A
untilyouhearabeeptobegininverteroperation.Your
UPSwillnowprovideoutputpowerthroughitsACoutletstoconnectedequipment.Your
UPS will performa brief self-test andshowthe results on theLCD Display
B
. See
“StartupSelf-Test”inthe“Operation”sectionforthedisplaysequence.*
*ColdStart:TouseyourUPSasastand-alonepowersourcewhenACinputpowerisunavailable(i.e.duringa
blackout),youcan“coldstart”yourUPSandpowerconnectedequipmentfromtheUPS'sbattery.YourUPS's
batterymustbeatleastpartiallychargedforthisoperationtosucceed.Pressandholdthe“ON”Buttonuntilyou
hearabeeptocoldstartyourUPS.TheLCDDisplaywillshowONBATTERYMODE.Batterypowerwillbegin
discharging. Some electronic equipment may draw more amps during startup; when cold starting, consider
reducingtheinitialloadontheUPS.
Note: UPS system will function properly upon initial startup; however, maximum runtime
for the unit’s battery will only be accessible after it has been charged for 24 hours.
To Turn the UPS System OFF: PresstheUPS's“OFF”Buttonuntilyouhearabeep.
TheLCDDisplaywillshow“BYPASSMODE.”TheUPSwillcontinuetoautomatically
chargeitsbatteriesaslongasACinputpowerispresent.Tocompletelydeactivatethe
UPS,unplugtheUPS'slinecordwhentheUPSsystemisinbypassmode.
1
2
1
2
A
B
3
3
Note: The output voltage is set at 208/120V~ when the UPS is shipped from the factory. If you need to change
the output voltage of the UPS, refer to “Output Voltage Selection” in the “Operation” section. You should select
the correct output voltage before connecting your equipment to the UPS.
Plug your UPS's line cord into an electrical outlet.
YourUPSmustbeconnectedtoadedicatedcircuitofsufficientamperage.
Note! After you connect the UPS to a live AC power source, the UPS (in “STANDBY
MODE”) will automatically charge its batteries, but will not supply power to its
outlets until it is turned on.
Input and Output Ratings
Input Maximum Rated Maximum Rated Typical
Model Voltage Input Current Output Current Wire Size
SU5000RT4U 100-140V (L1-N: L2-N) 20A 30A N/A
SU6000RT4U 100-140V (L1-N: L2-N) 24A 30A N/A
SU8000RT4U 100-140V (L1-N: L2-N) 34A 40A 8 AWG
201102170 932611.indd 6 3/30/2011 10:22:12 AM
7
Optional Connection
The following connections areoptional.Your UPS systemwill function properlywithout
theseconnections.
USB and RS-232 Serial Communication Connection
Use the included USB cable
1a
and/or RS-232 DB9 serial cable
1b
to connect the
communicationportofyourcomputertothecommunicationportofyourUPS.Installon
your computer the Tripp Lite PowerAlert Software appropriate to your computer's
operatingsystem.ConsultyourPowerAlertmanualformoreinformation.
Dry Contact Note: Dry contact communications are simple, but some knowledge of
electronicsisnecessarytoconfigurethem.TheDB9port'spinassignmentsareshownin
diagram
1c
.IftheUPSbatteryislow,theUPSsendsasignalbybridgingpins1and5.
Ifutilitypowerfails,theUPSsendsasignalbybridgingpins8and5.ToshuttheUPS
downremotely,shortpin3andpin9foratleast3.8seconds.
EPO Port Connection
Thisoptionalfeatureisonlyforthoseapplicationsthatrequireconnectiontoafacility’s
EmergencyPowerOff(EPO)circuit.WhentheUPSisconnectedtothiscircuit,itenables
emergencyshutdownoftheUPS’sinverterandinhibitstransfertointernalbypass.Using
the cable provided, connect the EPO port of your UPS (see
2a
) to a user-supplied
normallyclosedornormallyopenswitchaccordingtothecircuitdiagram(see
2b
).
Note:
1. If using a cable other than what is supplied, the cable should not exceed 350 feet
or have a resistance of greater than 10 ohms.
2. If a non-latching EPO switch is used, the EPO must be held for a minimum of 1
second. This does not apply to a latching EPO switch.
CAUTION: The EPO port is not a phone line surge suppressor; do not connect a
phone line to this port.
UPSUnitStatewhenassertingEPOwithAClinepresent:
LEDs Output Fans Serial SNMP USB LCD Screen
OFF OFF ON ON ON ON
“Emergency
Stop”
TorestarttheUPSunitafterassertingEPOwithAClinepresent:
Option 1:
1.VerifythattheEPOassertionhasbeenremovedorcleared.
2.PressONbuttonuntilunitdisplays"STANDBY"(approx.1second).
3.PressONbuttonagainandUPSoutputwillturnbackonafteritcompletes
diagnostics.
Option 2:
1.VerifythattheEPOassertionhasbeenremovedorcleared.
2.RemoveAClinepowertotheUPSunit.
3.ReapplyAClinepower.NowtheUPSwillstartbackupinnormaloperationmode.
UPSUnitStatewhenassertingEPOwithoutAClinepower:
LEDs Output Fans Serial SNMP USB LCD Screen
OFF OFF OFF OFF OFF OFF
“Emergency
Stop”
TorestarttheUPSunitafterassertingEPOwithoutAClinepower:
1.VerifythattheEPOassertionhasbeenremovedorcleared.
2.ReapplyAClinepowertotheUPSunit.NowtheUPSwillstartbackupinnormal
operation mode.
1
2
1a
1b
4-5
2a
2b EPO Pin Assignment
1c
201102170 932611.indd 7 3/30/2011 10:22:12 AM
8
3a
3b
External Battery Connection
YourUPScomeswitharobustinternalbatterysystem;externalbatteriesareneededonly
to extend runtime. Adding external batteries will increase recharge time as well as
runtime.TheillustrationshowsthelocationofyourUPS'sExternalBatteryConnector,
whereyouwillinsert the batterypackcable
3a
.Completeinstallationinstructions for
yourbatterypackappearinthebatterypackowner'smanual.Makesurethatcablesare
fullyinsertedintotheirconnectors.Smallsparksmayresultduringbatteryconnection;
thisisnormal.DonotconnectordisconnectbatterypackswhentheUPSisrunningon
batterypower.
NOTE: Select models feature a Battery Charge Level Switch
3b
. If you connect any
external batteries to these models, set the Battery Charge Level Switch (see diagram)
to the right (labeled “EXTERNAL BATTERIES”). This will increase your UPS's
charger output so the additional batteries charge faster.
CAUTION! DO NOT set the Battery Charge Level Switch to the right (labeled
“EXTERNAL BATTERIES”) without an external battery connected. There is a risk
of damaging the UPS's internal battery system.
Internal SNMP/WEB Card Insertion
Removetheslot'scovertoinstallanoptionalinternalSNMP/Webaccessorycard(Model:
SNMPWEBCARD)toenable remoteUPSmonitoringand controlviaSNMP,Webor
telnet.ContactTrippLiteCustomerSupportat(773)869-1234formoreinformation,
includingalistofavailableSNMP,networkmanagementandconnectivityproducts.
3
4
4
SU6000RT4U
Shown (Rear View)
Optional Connection (continued)
201102170 932611.indd 8 3/30/2011 10:22:13 AM
99
Manual Bypass Operation (for UPS maintenance or replacement)
WARNING! For qualified service personnel only. Failure to follow the bypass procedure completely will not adequately power down
the UPS power/battery module, resulting in the continued risk of death or injury from potential contact with high voltage. The UPS's
power/battery module and detachable PDU are extremely heavy. This procedure requires several people to perform.
TheUPSsystemincludesaself-containedpower/batterymodulealongwithanindependent,detachablePDUwithabypassswitch.Thisswitch
allowsqualifiedservicepersonneltoremovethedetachablePDUfromthepower/batterymoduleforroutinemaintenancewithoutdisrupting
powertoconnected loads.While this switchisset to “BYPASS”,connected equipment willreceive unfilteredAC mains power, but the
equipmentwillnotreceivebatterypowerintheeventofablackout.
Note:AnoptionaldetachablePDUwithhardwireinput/outputisalsoavailableseparatelyfromTrippLite.ContactTrippLitefordetails.
(Optional:Duringahot-swap,thePDUcanbehousedinthebackoftherackconfigurationusingsuppliedPDUhangerbracketsandhardware.
See STEP 1belowformountinginstructions.)
I/P BYPASS
BATTERYAC/DC DC/AC O/P
OFFON
MUTE SELECT
SETUP
UPS Power/Battery Module Removal
STEP 1. (Optional)AttachaPDUhangerbrackettotherightandleftside,rearmountingrailsusingincludedscrewsandcagenuts.
Important:determiningwheretoattachyourPDUhangerbracketswilldependonyourrackconfiguration.Generallyitis
recommendedtomountthebracketsinaUspaceclosetowheretheUPSandPDUaremountedin.Besuretomountbothleftand
rightbracketsinthesameUspaceoneachside.
STEP 2. DisablePowerAlertSoftwareanddisconnectcommunicationcable(s)fromthecommunicationport(s)
A
ontheUPSpower/
batterymodule.
STEP 3. PresstheUPS's“OFF”Button
B
,iftheUPSispowered,untilyouhearabeepandseea"SwitchtoBypassN(NO)/Y(OFF)"
messageshownintheLCDDisplay
C
.Tocontinue,presstheOFFbutton.Ifthebypassvoltageisoutofrange,theunitwill
display"BypassOutofRange,UnabletoBypass"andwillcanceltherequest.Repeatthisprocedure.Iftheerrorpersists,contact
CustomerSupport.
STEP 4. TurnthedetachablePDU'sBypassSwitch
D
to“BYPASS”.
STEP 5. IfanexternalbatterymoduleisconnectedtotheUPS
E
,disconnectitfromtheUPS.
The UPS power/battery module is now safely powered down and it can be detached from the PDU
to perform maintenance/replacement.
STEP 6: RemovethefivescrewsthatholdthedetachablePDUtothepower/batterymodule.
STEP 7: Usingseveralassistantsateachend,carefullypullthedetachablePDUawayfromthepower/batterymodule.Duringthisprocess,
ensurethateachsectionisproperlysupportedaftertheyareseparated.
• Ifthesectionsaredetachedinarackmountapplication,ensurethateachsectionremainsadequatelysupportedbytheUPS's
rackmountrails.RemovetherackmountinghardwarefromthefrontpaneloftheUPS;slidethepower/batterymoduleforward,
andremove.ThePDUwillremainsupportedontherackmountrails.CareshouldbetakeninthisprocessbecausethePDUwill
notbesecuredtotherackwithhardwareofanykind.
•IfitisdesiredtoleavethedetachedPDUintherack,hangtheunitinbackoftherackontheinstalledPDUhangerbracketsby
thescrewsusedtoattachthePDUtotheUPSsystem.
• Ifthesectionsaredetachedinatowerapplication,ensurethatthePDUissupportedbytheUPS'stowerfeet.Adjustthetower
feetsotheyareasclosetogetheraspossible.
To reattach the PDU, reverse the process listed above.
Steps 2, 4 & 5
Step 3
E
D
A
C
B
WARNING! High Voltage! Risk of electrical shock! SEE PAGE 9.
201102170 932611.indd 9 3/30/2011 10:22:14 AM
1010
Manual Bypass Operation (for UPS maintenance or replacement)
Step 6
Step 7
High Voltage Warnings
WARNING! High Voltage! Risk of electrical shock! SEE BELOW.
Contacts on Power/Battery Module
WARNING!
High Voltage!
Risk of electrical shock!
Due to the presence of high voltage internal batteries,
even without AC present, these contacts are live!
Do not let these contacts touch any surface!
A
Contacts on Detachable PDU
WARNING!
High voltage!
Risk of electrical shock!
If AC is present and Bypass Switch is set to
“Bypass”, these contacts are live!
Do not let these contacts touch any surface!
B
See Warning
Statements
Below!
A
B
Step 7
201102170 932611.indd 10 3/30/2011 10:22:15 AM
1111
Operation
TheusercanentertheSetupModeatanytime(exceptduringtheDiagnosticMode)bypushingbothscrollbuttonsatthesametimeformore
than1second.TheSetupprocedureisasfollows:
Startup Self-Test
WhenyouturntheUPSON,itwillenterDiagnosticModeandperformaself-testlastingabout15seconds.Theresultsoftheself-testare
shownontheLCDscreeninthesequencesbelow.
DIAGNOSTIC MODE
FREQ OUT = XXHz
LCD Screen Message Sequence
(If UPS Is Started with AC Input)
DIAGNOSTIC MODE
FREQ OUT = XXHz
LCD Screen Message Sequence
(If UPS Is “Cold-Started” with No AC Input)
DIAGNOSTIC MODE
INPUT AC OK
DIAGNOSTIC MODE
INPUT AC BAD
DIAGNOSTIC MODE
BATTERY OK
DIAGNOSTIC MODE
BATTERY OK
DIAGNOSTIC MODE
CHARGER OK
DIAGNOSTIC MODE
AC/DC OK
DIAGNOSTIC MODE
AC/DC OK
DIAGNOSTIC MODE
TESTING INVERTER
DIAGNOSTIC MODE
TESTING INVERTER
UPS MODE
LOAD1 = XXX% X.XKW
ON BATTERY MODE
LOAD1 = XXX% X.XKW
Failed Self-Test
Ifaproblemisdetectedduringtheself-test,theLCDwilldisplayanerrormessage.IfyourUPSdisplaysanyofthefollowingmessagesinits
LCD,callTrippLiteTechnicalSupportat(773)869-1234forservice.
BAD BATTERY!
CALL FOR SERVICE
LCD Screen Messages
(If UPS Fails Self-Test)
CHARGER FAILURE!
CALL FOR SERVICE
AC/DC FAILURE!
CALL FOR SERVICE
INVERTER FAILURE!
CALL FOR SERVICE
OUTPUT FAILURE!
CALL FOR SERVICE
FAN FAILURE!
CALL FOR SERVICE
201102170 932611.indd 11 3/30/2011 10:22:16 AM
1212
Operation (continued)
Normal Operation
Duringnormaloperation,thefirstlineofyourLCDDisplayshowswhichoperatingmodeyourUPSisin:“UPSMODE”,“ONBATTERY
MODE”,“BYPASSMODE”or“STANDBYMODE”.
“UPS MODE”:TheUPSprovidesACpowerwhileutilitypowerisavailableandswitchestoONBATTERYMODEinstantly(zerotransfer
time)ifACpowerisinterrupted.
“ON BATTERY MODE”:TheUPSprovidesACpowerfrombatterybackupsolongasbatterypowerlasts.ItswitchesbacktoUPSMODE
ifutilitypowerisavailableandshutsdownifitrunsoutofbatterypower.
“STANDBY MODE”:TheUPSispluggedin,chargingit’sbatteriesandreceivingACpower.However,ithasnotbeenturnedon.
“BYPASS MODE”: TheUPSprovidesACpowerwhileutilitypowerisavailable.TheUPSshutsdownifACpowerisinterrupted.
ThesecondlineoftheLCDDisplayshowsbasicpowerconditions.PushtheSCROLLbuttonstobrowsethroughthesebasicpowerconditions
inthesequenceshownbelow.
XXXX MODE
LOAD1 = XXX% X.XKW
XXXX MODE
LOAD2 = XXX% X.XKW
XXXX MODE
IN = XXXV XX.X Hz
XXXX MODE
IN1 = XXXV XX.X Hz
XXXX MODE
IN2 = XXXV XX.X Hz
XXXX MODE
OUT = XXXV XX.X Hz
XXXX MODE
OUT1 = XXXV XX.X Hz
XXXX MODE
OUT2 = XXXV XX.X Hz
XXXX MODE
BATT = XXXVDC XXX%
On Battery Alarm
WhenintheONBATTERYMODE,theUPSpowermodulewillbeepto informyouthatitisusingbatterypowertosupportconnected
equipment.Ifitsconnectedbatteriesareatmorethanhalfcapacity,itwillbeepeverytwoseconds.Ifitsconnectedbatteriesarebelowhalf
capacity,itwillbeeptwicepersecond.Ifitsconnectedbatteriesarenearlydepleted,theUPSpowermodulewillbeepcontinuously.Tosilence
theOnBatteryAlarm,pressthe“ON/MUTE”Button.
201102170 932611.indd 12 3/30/2011 10:22:16 AM
1313
Operation (continued)
Note:
208 / 120V<120D Output Voltage (L1-L2)=208V, Output Voltage (L1,L2)=120V and L1 leads L2 120 degrees
208 / 120V<240D Output Voltage (L1-L2)=208V, Output Voltage (L1,L2)=120V and L2 leads L1 120 degrees
240 / 120V<180D Output Voltage (L1-L2)=240V, Output Voltage (L1,L2)=120V and L1 leads L2 180 degrees
Self-Test Is Running
TESTING BATTERY
LOAD1 = XXX% X.XKW
Additional Self-Test
Ifaself-testisinitiatedafterstartup,theLCDwilldisplayamessage.
Configuration Menu
TheUPSoutputvoltageissetat208/120V~whentheUPSisshippedfromthefactory.InordertochangetheoutputvoltageoftheUPS,you
firstneedtoenter“ONBATTERYMODE”bycold-startingtheUPS.(Thebatterymustbeatleastpartiallychargedforthisoperationto
succeed.)IftheUPSison,pressandholdthe“OFF”buttonuntilyouhearabeep,disconnectanyconnectedequipmentanddisconnectthe
UPSfromitsACpowerinput.AftertheUPSisdisconnectedfromACpower,pressthe“ON/MUTE”buttonuntilyouhearabeep.TheLCD
screenwillshow“ONBATTERYMODE”andanalarmwillsoundperiodicallytoinformyouthattheUPSisusingbatterypower.Silence
thealarmbypressingthe“ON/MUTE”button.
AftertheUPShasentered“ONBATTERYMODE”,presstheSCROLLUPandSCROLLDOWNbuttonssimultaneouslyforlongerthan
1second.TheUPSwillbeepandtheLCDwillshowtheSET-UPscreen(1).PresstheSCROLLUP/SELECTbuttontoenterthe“UPSSET-UP”
procedure(2). Press the SCROLL UP/SELECTbutton again to enter the “OUTPUT SELECT” procedure(3). There are 3 output voltage
selections.PresstheSCROLLDOWNbuttontoscrolltothedesiredoutputvoltageselection(3)-(5)andthenpresstheSCROLLUP/SELECT
buttontoselect it. The LCD willreturn to the“OUTPUTSELECT” screen(2). PresstheSCROLL DOWNbuttontoreach the SET-UP
screen(1)andpresstheSCROLLDOWNbuttonagaintoexittheSET-UPprocedure.TheLCDshouldbebackto“ONBATTERYMODE”.
Pressthe“OFF”keyuntilyouhearabeep,andtheUPSwillsavetheselectedoutputvoltageparameter.RestoretheACpowerinputofthe
UPSandpressthe“ON”keytoturnontheUPSandusetheSCROLLDOWNbuttontoscrollthroughthebasicpowerconditionsdisplays
andconfirmthattheoutputvoltagehasbeenchangedtothedesiredvalue.
EconomyMode(ECO)isahigh-efficiencyoperatingmodeinwhichthedoubleconversionprocessissuspended.Incomingpowerisfiltered,
andiftheinputvoltageiswithin+/-10%ofthenominalvoltage,itispassedthroughtoconnectedequipment.Iftheinputvoltagegoesoutside
ofthisacceptablerange,theunitautomaticallyreturnstoitsOnlineModetoprovideahighlyregulatedoutputderivedfromthesystem’s
inverter.Ifvoltagesubsequentlyreturnstotheacceptablerange,theunitwillreturntoitshighefficiencymode.
i
ECO
Scroll
Disable
Select
ECO
Exit
Enable
Select
ii
i
ECO
Scroll
Disable
Select
ECO
Exit
Enable
Select
ii
201102170 932611.indd 13 3/30/2011 10:22:17 AM
1414
Operation (continued)
TheUPSwillthenbeginacountdown.IftheUPSisstilloverloadedattheendofthecountdown,theUPSwillautomaticallygotoBYPASS
MODEtoprotectitsinverter.Thedurationofthecountdownvarieswiththeseverityoftheoverload,asfollows:
Overload Condition Countdown Duration
102% - 125% 1 minute
125% - 150% 30 seconds
> 150% Immediate Bypass
Bypass Messages
WhileinBYPASSMODE,theUPSmonitorsitsinputvoltageandpassesthatinputpoweralongtoconnectedequipment.TheUPSwillnot
providebatterybackupinBYPASSMODE.Iftheoutputvoltagedeviatesfromanacceptablerange(between15%higherand20%lowerthan
nominal),theUPSdisplaystheconditiononitsLCDandstopssupplyingoutputpowertoitsload.
Bypass Voltage Conditions
L1 > 15% Higher
Than Nominal Voltage
L2 > 15% Higher
Than Nominal Voltage
L1 > 20% Lower
Than Nominal Voltage
L2 > 20% Lower
Than Nominal Voltage
L1 Voltage Was Too High,
Now Returned to Nominal Voltage
L2 Voltage Was Too High,
Now Returned to Nominal Voltage
L1 Voltage Was Too Low,
Now Returned to Nominal Voltage
L2 Voltage Was Too Low,
Now Returned to Nominal Voltage
BYPASS AC1 HIGH
LOAD1 = XXX% X.XKW
LCD Screen Messages
BYPASS AC2 HIGH
LOAD1 = XXX% X.XKW
BYPASS AC1 LOW
LOAD1 = XXX% X.XKW
BYPASS AC2 LOW
LOAD1 = XXX% X.XKW
BYPASS AC1 WAS HI
LOAD1 = XXX% X.XKW
BYPASS AC2 WAS HI
LOAD1 = XXX% X.XKW
BYPASS AC1 WAS LO
LOAD1 = XXX% X.XKW
BYPASS AC2 WAS LO
LOAD1 = XXX% X.XKW
OVERLOAD!
LOAD1 = XXX% X.XKW
OVERLOAD!
LOAD2 = XXX% X.XKW
Overload Messages
WhentheUPSdetectsanoutputoverload,itsLCDwillswitchtothefollowingdisplay:
201102170 932611.indd 14 3/30/2011 10:22:17 AM
1515
Operation (continued)
Shutdown Messages
YourUPSwillshutdownandtheLCDwilldisplayamessageifitdetectsoneofthefollowingconditions.Note:Duringalltheseconditions,
the“Input,”“Output”and“Bypass”LEDswillbeilluminated.
Shutdown Conditions
L1 Extended Overload
L2 Extended Overload
L1 to L2
Output Short Circuit
L1 to N Output Short Circuit
L2 to N Output Short Circuit
Remote Shutdown Command
(via DB9)
Remote Shutdown Command
(via EPO)
Battery Depletion
Site Wiring Fault
EEPROM Failure
Positive DC BUS Voltage
is Too High
Positive DC BUS Voltage
is Too Low
Negative DC BUS Voltage
is Too High
Negative DC BUS Voltage
is Too Low
Fan Failure
UPS Overtemperature
L1 Inverter Too High
L1 Inverter Too Low
SHUTDOWN
L1 OVERLOAD=XXX%
LCD Screen Messages
SHUTDOWN
L2 OVERLOAD=XXX%
OP SHORTCIRCUIT
LOAD1 = XXX% X.XKW
OP1 SHORTCIRCUIT
LOAD1 = XXX% X.XKW
OP2 SHORTCIRCUIT
LOAD1 = XXX% X.XKW
REMOTE COMMAND
LOAD1 = XXX% X.XKW
EMERGENCY STOP!
LOAD1 = XXX% X.XKW
SITE WIRING FAULT
LOAD1 = XXX% X.XKW
EEPROM FAIL
LOAD1 = XXX% X.XKW
+DC BUS HIGH
LOAD1 = XXX% X.XKW
+DC BUS LOW
LOAD1 = XXX% X.XKW
-DC BUS HIGH
LOAD1 = XXX% X.XKW
-DC BUS LOW
LOAD1 = XXX% X.XKW
FAN FAIL
LOAD1 = XXX% X.XKW
OVERTEMPERATURE
LOAD1 = XXX% X.XKW
LOW BATTERY
LOAD1 = XXX% X.XKW
INVERTER1 HIGH
LOAD1 = XXX% X.XKW
INVERTER1 LOW
LOAD1 = XXX% X.XKW
L2 Inverter Too High
L2 Inverter Too Low
INVERTER2 HIGH
LOAD1 = XXX% X.XKW
INVERTER2 LOW
LOAD1 = XXX% X.XKW
Shutdown Conditions
Internal Charger Failure
External Charger Failure
Battery Open / Bad Battery
Phase Lock Failure,
Bypass Lockout
Phase Lock Failure,
Inverter Lockout
INT CHARGER FAIL
LOAD1 = XXX% X.XKW
LCD Screen Messages
EXT CHARGER FAIL
LOAD1 = XXX% X.XKW
BAD BATTERY!
LOAD1 = XXX% X.XKW
BYPASS LOCKOUT
LOAD1 = XXX% X.XKW
INVERTER LOCKOUT
LOAD1 = XXX% X.XKW
201102170 932611.indd 15 3/30/2011 10:22:18 AM
1616
Internal Battery Replacement
Undernormalconditions,theoriginalbatteriesinyourUPSwilllastmanyyears.SeeSafetysectionbeforereplacingbatteries.Thebatteries
aredesignedforhot-swapreplacement(i.e.leavingtheUPSON),butsomequalifiedservicepersonnelmaywishtocompletelyturntheUPS
OFFanddisconnectequipmentbeforeproceeding.
Storage
BeforestoringyourUPS,turnitcompletelyOFF.IfyoustoreyourUPSforanextendedperiodoftime,rechargetheUPSbatteriesfor4to6
hoursonceeverythreemonths.Note:afteryouconnecttheUPStoutilitypower,itwillautomaticallybeginchargingitsbatteries.Ifyouleave
yourUPSbatteriesdischargedforanextendedperiodoftime,theywillsufferapermanentlossofcapacity.
Service
YourTrippLiteproductiscoveredbythewarrantydescribedinthismanual.AvarietyofExtendedWarrantyandOn-SiteServiceProgramsare
alsoavailablefromTrippLite.Formoreinformationonservice,visitwww.tripplite.com/support.Beforereturningyourproductforservice,follow
thesesteps:
1.Reviewtheinstallationandoperationproceduresinthismanualtoinsurethattheserviceproblemdoesnotoriginatefromamisreadingofthe
instructions.
2.Iftheproblemcontinues,donotcontactorreturntheproducttothedealer.Instead,visitwww.tripplite.com/support.
3.Iftheproblemrequiresservice,visitwww.tripplite.com/supportandclicktheProductReturnslink.FromhereyoucanrequestaReturned
MaterialAuthorization (RMA) number, whichis required forservice.This simple on-lineform will ask foryour unit’s model andserial
numbers,alongwithothergeneralpurchaserinformation.TheRMAnumber,alongwithshippinginstructionswillbeemailedtoyou.Any
damages(direct,indirect,specialorconsequential)totheproductincurredduringshipmenttoTrippLiteoranauthorizedTrippLiteservice
centerisnotcoveredunderwarranty.ProductsshippedtoTrippLiteoranauthorizedTrippLiteservicecentermusthavetransportationcharges
prepaid.MarktheRMAnumberontheoutsideofthepackage.Iftheproductiswithinitswarrantyperiod,encloseacopyofyoursalesreceipt.
ReturntheproductforserviceusinganinsuredcarriertotheaddressgiventoyouwhenyourequesttheRMA.
1
2
3
4
56
RemoveFrontPanelandBatteryCoverPlate
DisconnectBatteries
Remove/DisposeofBatteries
AddBatteries
ConnectBatteries.Attachconnectors:black-to-blackandred-to-red
ReplaceBatteryCoverPlateandFrontPanel
1
2
3
4
5
6
201102170 932611.indd 16 3/30/2011 10:22:18 AM
1717
Warranty
2-YEAR LIMITED WARRANTY
Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material and workmanship for a period of 2 years (except internal UPS system
batteries outside USA and Canada, 1 year) from the date of initial purchase. If the product should prove defective in material or workmanship within that period, Seller will repair or replace the
product, in its sole discretion. Service under this Warranty can only be obtained by your delivering or shipping the product (with all shipping or delivery charges prepaid) to: Tripp Lite; 1111 W.
35th Street; Chicago IL 60609; USA. Seller will pay return shipping charges. Call Tripp Lite Customer Service at (773) 869-1234 before sending any equipment back for repair.
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES
OTHER THAN THE WARRANTY EXPRESSLY SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING ALL
WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES
ALL INCIDENTAL AND CONSEQUENTIAL DAMAGES. (Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights, and you may have other rights which vary from
jurisdiction to jurisdiction).
Tripp Lite; 1111 W. 35th Street; Chicago IL 60609; USA
WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate or safe for the use intended. Since individual applications are subject to great
variation, the manufacturer makes no representation or warranty as to the suitability or fitness of these devices for any specific application.
Visitwww.tripplite.com/warrantytodaytoregisterthewarrantyforyournewTrippLiteproduct.You'llbeautomaticallyenteredintoadrawing
forachancetowinaFREETrippLiteproduct!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
FCC Notice, Class A
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense. The user must use shielded cables and connectors with this equipment. Any changes or modifications to this equipment not expressly approved by Tripp Lite could void
the user’s authority to operate this equipment.
Regulatory Compliance Identification Numbers
For the purpose of regulatory compliance certifications and identification, your Tripp Lite product has been assigned a unique series number. The series number can be found on the product
nameplate label, along with all required approval markings and information. When requesting compliance information for this product, always refer to the series number. The series number should
not be confused with the marking name or model number of the product.
The policy of Tripp Lite is one of continuous improvement. Specifications are subject to change without notice.
Warranty Registration
201102170 93-2611_EN
201102170 932611.indd 17 3/30/2011 10:22:18 AM
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
28
Operación
Elusuariopuedeentraralmododeconfiguraciónencualquiermomento(exceptoduranteelmododediagnóstico)presionandoambosbotones
dedesplazamientoalmismotiempodurantemásde1segundo.Elprocedimientodeconfiguracióneselsiguiente:
Auto-prueba de arranque
CuandoenciendeelUPS,ingresaal mododediagnósticoyrealizaunaauto-prueba queduracercade15segundos.Losresultadosde la
auto-pruebasemuestranenlapantallaenlassecuenciasindicadasacontinuación.
DIAGNOSTIC MODE
FREQ OUT = XXHz
Secuencia de mensajes de pantalla
(Si el UPS arranca con entrada de CA)
DIAGNOSTIC MODE
FREQ OUT = XXHz
Secuencia de mensajes de pantalla
(Si el UPS "arranca en frío”
sin entrada de CA)
DIAGNOSTIC MODE
INPUT AC OK
DIAGNOSTIC MODE
INPUT AC BAD
DIAGNOSTIC MODE
BATTERY OK
DIAGNOSTIC MODE
BATTERY OK
DIAGNOSTIC MODE
CHARGER OK
DIAGNOSTIC MODE
AC/DC OK
DIAGNOSTIC MODE
AC/DC OK
DIAGNOSTIC MODE
TESTING INVERTER
DIAGNOSTIC MODE
TESTING INVERTER
UPS MODE
LOAD1 = XXX% X.XKW
ON BATTERY MODE
LOAD1 = XXX% X.XKW
Fallo durante la auto-prueba
Sisedetectaalgúnproblemadurantelaauto-prueba,lapantallamostraráunmensajedeerror.SisuUPSmuestracualquieradelossiguientes
mensajesenpantalla,llamealSoportetécnicodeTrippLiteal(773)869-1234.
BAD BATTERY!
CALL FOR SERVICE
Mensajes de pantalla
(Si falla la auto-prueba del UPS)
CHARGER FAILURE!
CALL FOR SERVICE
AC/DC FAILURE!
CALL FOR SERVICE
INVERTER FAILURE!
CALL FOR SERVICE
OUTPUT FAILURE!
CALL FOR SERVICE
FAN FAILURE!
CALL FOR SERVICE
201102170 932611.indd 28 3/30/2011 10:22:22 AM
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
4545
Fonctionnement
L'utilisateurpeurentrerenmodederéglageentouttemps(saufpendantlemodeDiagnostic)enappuyantsurlesdeuxboutonsdedéfilement
enmêmetempspendantplusd'1seconde.Laprocédurederéglageestlasuivante:
Autotest de démarrage
Quandvousmettezl'UPSenmarche,ilentreraenmodeDiagnosticetexécuteraunautotestd'environ15seconds.Lesrésultatsdecetautotest
sontmontréssurl'écranACLdanslesséquencescidessous.
DIAGNOSTIC MODE
FREQ OUT = XXHz
Séquence de message de l’écran ACL
(Si l’UPS est démarré
avec CA d’entrée)
DIAGNOSTIC MODE
FREQ OUT = XXHz
Séquence de message de l’écran ACL
(Si l’UPS est démarré
“ à froid” sans CA d’entrée)
DIAGNOSTIC MODE
INPUT AC OK
DIAGNOSTIC MODE
INPUT AC BAD
DIAGNOSTIC MODE
BATTERY OK
DIAGNOSTIC MODE
BATTERY OK
DIAGNOSTIC MODE
CHARGER OK
DIAGNOSTIC MODE
AC/DC OK
DIAGNOSTIC MODE
AC/DC OK
DIAGNOSTIC MODE
TESTING INVERTER
DIAGNOSTIC MODE
TESTING INVERTER
UPS MODE
LOAD1 = XXX% X.XKW
ON BATTERY MODE
LOAD1 = XXX% X.XKW
Échec de l'autotest
Siunproblèmeestdétectéduranttl'autotest,l'ACLafficheraunmessaged'erreur.SivotreUPSafficheundesmessagessuivantssurl'écran
ACL,communiquezavelesupporttechniquedeTrippLiteau(773)869-1234pourduservice.
BAD BATTERY!
CALL FOR SERVICE
Messages sur l’écran ACL
(En cas d‘échac de l’autotest)
CHARGER FAILURE!
CALL FOR SERVICE
AC/DC FAILURE!
CALL FOR SERVICE
INVERTER FAILURE!
CALL FOR SERVICE
OUTPUT FAILURE!
CALL FOR SERVICE
FAN FAILURE!
CALL FOR SERVICE
201102170 932611.indd 45 3/30/2011 10:22:28 AM
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
201102170 93-2611_FR
1111 W. 35th Street, Chicago, IL 60609 USA
www.tripplite.com/support
Copyright © 2011 Tripp Lite. All rights reserved. SmartOnline™ is a trademark of Tripp Lite.
201102170 932611.indd 52 3/30/2011 10:22:30 AM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

Tripp Lite SmartOnline SU5000RT4U User manual

Tripp Lite
Brand
Tripp Lite
Model
SmartOnline SU5000RT4U
Category
Uninterruptible power supplies (UPSs)
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents