Page is loading ...
and
Maintenance
Ice Machines
15iM (marvel)
25iM (Marvel)
25OiM (Outdoor)
NOTE
Important Safety Instrucons
Recognize Safety Symbols,
Words, and Labels.
WARNING-
CAUTION-
NOTE-
-
TABLE OF CONTENTS
3
3
3
6
7
7
7
9
9
UNPACKING YOUR ICE MACHINE
Remove Interior Packaging
-
Important
Note to Customer
-
Warranty Registraon
-
-
Help Prevent Tragedies
3
Select Locaon
-
Outdoor Installaon
-
Winterizing your Outdoor Ice Maker
-
Front Grille
-
Rear
Cabinet Clearance
INSTALLING YOUR ICE MACHINE
NOTE
Leveling Legs
-
• Do not splash or spray water from a hose on the ice ma-
chine! Doing so may cause an electrical shock, which may
result in severe injury or death.
• This unit should not, under any circumstances, be installed
to an un-grounded electrical supply.
Electrical Connecon
-
-
Electrical Extension cords should
not be used. They can be hazard-
ous and cause decient operaon. The wall receptacle should
be located near the product and be a polarized type with
adequate ground protecon. The product must be installed to
your local building codes and ordinances.
-
INSTALLING YOUR ICE MACHINE
NOTE
Water Supply
-
NOTE: DO NOT USE A SELF-PIERCING
TYPE VALVE.-
-
-
Water
Supply
Line
Water supply
inlet
Ice Maker
INSTALLING THE WATER SUPPLY
6
NOTE
Turning on the ice machine
-
-
-
Ice maker operaon
-
Water Fill Adjustment
-
-
-
USING YOUR ICE MACHINE
7
DIMENSIONS FOR MODEL 15IM SOLID DOOR
RECOMMENDED ROUGH IN OPENING DIMENSIONS,15IM SOLID DOOR
standard cabinet
DIMENSIONS FOR MODEL 25IM SOLID DOOR
RECOMMENDED ROUGH IN OPENING DIMENSIONS, 25IM SOLID DOOR
-
standard cabinet
9
DIMENSIONS FOR MODEL 25OIM SOLID DOOR
RECOMMENDED ROUGH IN OPENING DIMENSIONS, 25OIM SOLID DOOR
-
standard cabinet
DIMENSIONS FOR MODEL 25IM SOLID OVERLAY DOOR
RECOMMENDED ROUGH IN OPENING DIMENSIONS, 25IM SOLID OVERLAY DOOR
-
standard cabinet
NOTE
NOTE
Step 1: Verify door alignment
-
-
-
Step 2: Remove door
-
Step 3: Remove gasket
Step 4: Cut overlay panel
panel
Step 5: Drill hinge clearance holes in overlay panel
-
-
-
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS
NOTE
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS
Step 6: Drill panel mounng holes
If your ice machine has a door lock proceed to Step 7. If your
ice machine does not have a door lock proceed to Step 9.
Step 7: Mark and drill lock hole.
-
adapter
adapter
panel
Material Type #8 Wood Screw
SECTION A-A
SCALE 1 : 1
LOCK
NUT
BRASS EXTENSION
CAM
PHILLIPS SCREW
13/16 COUNTER
BORE 7/16 DEEP
15/32 HOLE
3/4 INCH
WOOD PANEL
SPRING WASHER
INNER
DOOR
Step 9: Secure overlay panel to the door.
Step 10: Install lock cam (Models with locks only).
-
Step 12: Install the door
-
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS
Step 8: Assemble the lock parts
adapter
Step 11: Install door gasket
Cabinet
-
Interior
Care of Unit
CARE AND CLEANING
Defrosng Instrucons
-
ENERGY SAVING TIPS
The following suggesons will minimize the cost of
operang your ice machine appliance.
-
Problem Possible Cause Remedy
ice
-
Before You Call for Service
Electrocuon Hazard
TROUBLESHOOTING YOUR ICE MACHINE
Problem Possible Cause Remedy
-
-
-
-
TROUBLESHOOTING YOUR ICE MACHINE
For Your Records
-
-
If Service is Required:
OBTAINING SERVICE
Table B
Parts or Service
Not Supplied or Designated by AGA MARVEL
-
-
-
-
Enre Product
Limited One Year Parts and Labor Warranty
-
Addional Second Through Fih Year
Limited Parts Only Warranty
-
-
-
HOUSEHOLD PRODUCT WARRANTY
/