AEG MBS 6000 User manual

Brand: AEG

Model: MBS 6000

Type: User manual

Externe Handumgehungseinheit

für USV PROTECT C.6000R

External Bypass Unit

for UPS PROTECT C.6000R

Typ / Type

MBS 6000

AEG Power Solutions GmbH

Änderung / Revision 01 / Schenuit/ Schneider

Datum / Date 09.07.2009

Operating instructions

8000019069 BAL, en

1 General

The external, manually operated bypass unit is an option for the

PROTECT C.6000R UPS series in a rack version with 2U. It is

used for disconnecting the UPS, for example for maintenance

purposes, whilst the connected loads continue to be supplied

without interruption. As well as solely bypass operation, an

additional switch setting permits UPS test operation. Separately

fused non-heating appliance connectors make it possible for the

loads to be supplied directly from the MBS 6000. LEDs with

various colours clearly signal which operating status has been

selected.

Scope of delivery:

♦ External bypass unit MBS 6000

♦ 2 connection cables to the UPS

♦ Operating instructions

Prerequisite:

♦ AEG UPS in the PROTECT C.6000R series

Technical data:

Nominal connection voltage /

- frequency

230 VAC 50/60 Hz

Nominal current 32 A

Number of output sockets

(load connection)

8 x IEC 320 C13 (10 A),

fused in pairs

by miniature fuse

5 x 20 mm, T

10 A

additional non-fused

output on terminal

Housing colour blackline

Dimensions (HxWxD)

19-inch / rack operation

88 mm x 483 mm x 350 mm

U x 19"

2 Description

UPS Bypass Switch

USV Handumgehungsschalter

Achtung: Bedienungs-

anleitung beachten!

Attention: Refer to

operation instructions

UPS

NORMAL

SERVICE

BYPASS

Bypass

Tes t

Normal

Bypass

Tes t

Normal

The external bypass is used for changing over between

¾ "NORMAL"

operation (default switch position),

i.e. secure load supply with UPS back-up.

¾ "TEST"

operation (service position),

i.e. load supply directly from the mains,

additional mains supply to the UPS for service purposes.

¾ "BYPASS"

operation (bypass position),

i.e. load supply directly from the mains,

additional complete isolation of the UPS

(Attention! UPS output may still be live due to its internal

voltage source!)

If there is a mains failure during "TEST" and "BYPASS"

operation then the supply to the connected loads will be

interrupted.

IMPORTANT:

UPS must be switched to “BYPASS” operation,

if external bypass switch will be operated !

(refer to the UPS operating instructions)

3. Installation (mechanical)

During subsequent installation in the rack, take care that the unit is

located close to the UPS so as firstly to establish the causal

connection between the two and secondly to facilitate connection

and subsequent replacement of the UPS.

4 Connection (electrical)

If you have already taken the UPS into operation then switch it off as

the first step. Now disconnect the UPS from the mains by

disconnecting the mains connector.

¾ Before you perform the installation described below, make sure

that none of the cables are live.

¾ Make sure that the external bypass switch is in its default

position "NORMAL"

zum

USV Ausgang

Output

Output Output

Fuse

250V/10A

Fuse

250V/10A

Fuse

250V/10A

Fuse

250V/10A

Netzeingang

AC Input to UPS Output

zum

USV Eingang

to UPS Input

Ausgang

Output

Rear view of MBS 6000

{

Connect the input of the external bypass to the mains

connection cable provided with the UPS and plug the mains

connector into a suitable shockproof socket. In particular for

types with high power ratings, make sure that the fuse in your

sub-distribution system is sufficiently large.

Two connection cables are supplied with the external bypass.

Make the following connections:

Connect "OUTPUT" to the UPS output

}

Connect "INPUT" to the UPS mains input.

As the last step, connect your loads. To do this, use the load

connection cables provided with the UPS.

This completes the installation and cabling of the UPS with the

external bypass unit. Now start up the UPS system in accordance

with the operating instructions.

5 Wiring diagrams

UPS operation

Service position

Manual bypass

( NORMAL )

( TEST )

( BYPASS )

Guarantee Certificate

Type: …….……………….…......................................................

Serial no.: ………….…..……………..........................................

Date of purchase: ……………………...........……………….......

Dealer stamp / Signature

Errors and changes excepted.

Emil-Siepmann-Straße 32

59581 Warstein - Belecke

Germany

Tel.: +49 (0) 180 523 4787

Fax: +49 (0) 180 523 4789

www.aegpartnernet.com

Operating instructions

8000019069_01 BAL, en

AEG MBS 6000 User manual

AEG MBS 6000 User manual

Related papers

Other documents