DLS DLS CAD11 Owner's manual

Brand: DLS

Model: DLS CAD11

Category: Musical Equipment

Type: Owner's manual

This manual is also suitable for

CLASSIC CAD11

DLS DLS CAD11 is a digital mono amplifier with a wide range of capabilities that can greatly enhance your audio experience. With 400W of power output in 4 ohms, it can easily drive even the most demanding subwoofers. The amplifier also features a variable low-pass crossover, subsonic filter, and bass boost, giving you complete control over the sound quality. Additionally, the phase control and remote bass level control allow you to fine-tune the sound to your liking.

How to install and

operate the

DLS CAD11

digital mono

amplifier

Welcome!

This owners manual is written in easy english and

uses a lot of drawings to simply the installation and

use of the above amplifier.

Your DLS amplifier must be installed correctly in or-

der to work well. This manual will show you how to

install the amplifier like a pro. Please read the entire

manual before beginning the installation.

Install the amplifier yourself if you feel confident with

our instructions and if you have the proper tools.

However if you feel unsure, turn over the installation

job to someone better suited to it.

Warranty Service

This amplifier is covered by warranty, depending on

the conditions in the country where it is sold. If the

amplifier is returned for service, please include the

original dated receipt with the product.





Technical Assistance

For technical assistance ask the shop where the

product was sold or the distributor in your very coun-

try.

You can always phone the DLS Helpdesk in Sweden

+ 46 31 84 00 60 or send an e-mail to [email protected].

Information can also be found on our WEB-site

www.dls.se

Contents

Specifications................................ 1

Features…………………………….. 2

Installation…………………….……. 2

Trouble-shooting…………………… 2

Tools and materials needed………. 3

Amplifier installation kit………….... 3

Routing Wires…………………….... 3

Wiring

Power and Outputs……………..…. 4

Inputs and controls………………... 5

Input level control.......................... 5

Crossovers…………...................... 5

Phase control.....………………...… 5

Bass boost control......................... 6

Speaker wiring:

Single amplifier system………….…. 6

Testing.......................................... 6

Bridging two amplifiers................... 7

Professional tips…………………….. 8

Specifications

DLS CLASSIC CAD11

Number of channels 1

Power output in 4 ohm (0,4% THD) 1 x 400 W

Max output in 2 ohm (0,7% THD) 1 x 750 W

Max output in 1 ohm (1% THD) 1 x 1050 W

All above output power ratings at 13,8 Volt

Signal to noise ratio, A-weighted >100 dB

Damping factor >100

Frequency response 15 Hz - 160 Hz

Input impedance, low level 10 kohm

Input impedance, high level 100 ohm

Input sensitivity 0,15 - 5V

Phase control 0-180 degrees variable yes

Remote bass level control yes

Bass boost adjustable gain @45 Hz 0 - +18 dB

Filter subsonic, 24 dB slope 15 - 50 Hz

Filter lowpass 24 dB slope 15 - 150 Hz

Bridge mode (master/slave selector) Yes

Max size for power cables 21 mm

(4AWG)

Max size for speaker cables 10 mm

(7AWG)

Power consumption, idle 1,5 A

Maximum current draw 120 A

Built-in fan cooling yes

Fuse 4 x 30A

Dimensions (mm) 67x392x250

Dimensions (inch) 2,63x15,42x9,84

Weight 6 kg (13,8 lb)

We follow a policy of continuous advancement in

development. For this reason all or part of specifications

& designs may be changed without prior notice.

DLS Svenska AB

P.O. Box 13029

S-40251 Göteborg, Sweden

Tel: +46 31 840060

Fax: +46 31 844021

E-mail: [email protected]

www.dls.se

Approval of electromagnetic compatability according

to the EEC Directive 95/54/EC

E 13 Approval No: 022495

CAD11 include

 RCA input and output



 High level input with auto start

 Continuous variable low pass crossover



 Continuous variable subsonic crossover

 Bass boost feature

 Remote bass level control

 Phase control cont. variable 0-180 degrees

 Bridge mode master / slave selector

 Electronic protection circuitry against

short-circuit, DC offset and thermal overload.

Installation

Before you begin installation

Before you begin you need to read the manual, to have

some tools, cables and other material available. There

is one such list of material on the following page.

Amplifier location

Important

Allow air circulation around the amplifier.

Disconnect Battery

Before starting the instal-

lation, always disconnect

the negative terminal of

the battery.

The DLS Classic series of amplifiers have a

compact design that allows great flexibility in

mounting. You can mount it under a seat or in the

trunk.

When you select a location, do remember that the

amplifier generates a lot of heat.

Choose a location where air can circulate freely

around the amplifier. Do not cover the amplifier with

carpets or hide behind trim panels.

Do not mount the amplifier in an inverted or upside

down position.

Check all locations and placements carefully before

making any cuts, drilling any holes or making any

connections.

This is the best direction to

mount the amplifier to get

the best cooling.

CAD11

DLS logo on amplifier cooling flange

The DLS logo on top of the amplifier is attached

with two hex. screws. The logo can be removed

and twisted 90 or 180 degrees, and then screwed

back in wanted position. The logo can be mounted

in four different ways to match your installation.

If problems occur during the installation, or later,

this guide might help you to find out whats´s wrong.

The amplifier is dead:

1. Check power lead, ground and connections at

the amplifier using a multi meter.

2. Check the battery terminal connections.

3. Check the power lead fuse or circuit breaker. If

fuse damage continues, inspect the power lead

for short circuits.

4. Check the amplifier protection fuses. Are these

broken change to new ones with the same value.

If short circuiting continues, contact your local

DLS dealer. A fault may exist in the amplifier.

5. To start the amplifier requires a remote voltage

of 9-15 volt. Check the voltage with a multi meter.

Amplifier protection fuse blows at low

volume:

One or more speaker cables are shorted. Make an

insulation test with a multi meter. The cables must

not have a connection to earth.

The amplifier turns off after 10-30 minu-

tes:

The amplifier is overheating due to inadequate venti-

lation. Check mounting position is free from

obstruction.

Do this:

1. Move the amplifier to a place with better ventil-

ation.

2. Install one or two fans to cool down the heat-

sink.

3. Overheating can also be caused by an

impedance load below the level permitted.

No output from the speakers:

Check the following:

1. Speaker cable connections to both amplifier and

subwoofers.

2. Signal lead plugs and cables.

Troubleshooting

Tools and material needed

Tools:



 Flat and Phillips screwdrivers



 Wire cutter



 Wire stripper



 Electric drill with drills



 Crimping tool



 Digital multimeter or test lamp



 Wire brush, scraper or a piece

of an abrasive sheet to remove

paint for a good ground connection

 Grease to protect the ground

connection from corrosion

Material:

 Speaker wire: minimum

12 AWG = 4 mm

for subwoofers

 Sheet metal screws for mounting the

amplifier to the amplifier board and the

amplifier board to the car + some extra

for fuse holder, amplifier ground etc.



 Electrical insulation tape

 ½ inch thick plywood or particle board for

the amplifier to be mounted upon.

Amplifier installation kit:

If available,buy an amplifier installation kit. It

contains normally all you need. This is what you

have to buy if you buy the items separately

 20- 25 feet = 6- 7.5 meter power cable,

preferably AWG 4 = 21 mm

or heavier

 1 pc of fuseholder to install close to the

car battery + fuse 100 Ampere.

 20 feet of AWG 15 = 1,5 mm

wire for

remote turn on / off cable from radio.

 RCA-cable for input from radio.

- 20 feet or 5 meter for trunk installations

-12 feet or 2 – 3 meter for under seat

installations

 One min. 8 gauge ring crimp terminal

for the amplifier ground connection.

 Wire ties

 Insulating grommet or insulating tube

Routing wires

Stereo

head unit

Professional Tip:

If amplifier installation kits are available with diffe-

rent size of power cable, chose the most heavy

power cable to improve sound quality and to allow

more amplifiers to be installed now or later.

If possible buy AWG 4 = PL 21 mm

(or heavier)

cable for best performance.

High current draw

The CAD11 is a mono amplifier with high power output.

The current draw is also high so you must make sure

that your vehicles power system (battery and alternator)

can provide all the power you need. If you have a bad

battery or alternator in can result in a poor sound or

even worse, a broken battery or alternator.

CAD11

Wiring

Power and Outputs

CAD11

Power terminal ( +12V)

+12V REM GND

Remote terminal ( REM )

For RCA cable signal input:

Connect the radio power antenna lead = remote

turn on/off from the car stereo to the amplifier

remote connection. This turns on the amplifier

whenever the car stereo is turned on.

You can either use the built in remote cable in the

RCA cable itself or use a separate cable.

Sometimes a small disturbance may enter the

amplifier coming from the remote voltage , through

the built in remote wire and into the RCA cable.

Thus we recommend to use a separate remote wire

and run the RCA lead separate from remote wire,

power cables and speaker cables.

You can either use a crimp fork terminal or insert

the cable directly into the amplifier terminal. If there

is no remote voltage available from the stereo, you

must connect to the ignition key through the radio

or any accessories fuse.

DLS

DLS FH 2B

fuse holder

Connect to a good chassis ground. The ground

connection should be clean, unpainted metal to prov-

ide a good electrical connection. Use a wire brush, a

scraper or a piece of an abrasive sheet to clean the

metal. Use a lock washer or two to secure contact.

Protect with silicon grease or by paint applied

afterwards.

+12V REM GND

Power Light / Protect light

The power light (green ) comes on when

the amplifier is turned on.

The protect light ( red ) comes on when

the amplifier shuts down from

overheating or short circuit.

Fuses

Use only 30 ampere

ATC blade type fuses.

CAD11 uses four 30

ampere fuses.

30A

For High Level input:

We recommend you to connect the remote wire

as described above. The amplifier will produce soft

on / soft off operation this way. You must set the

Hi level/Low level switch to Low level position in

this case.

In the case that there is no remote voltage available

from the car stereo or you want to simplify the

installation, the amplifier can be turned on/ turned

off by the high level input voltage. This is done

when the Hi level/Low level switch is set to Hi level

position. There is a small disadvantage that this

function gives soft turn off operation but some plop

sound when switching off.

Connect the fuse holder as close to the vehicle

battery + as possible, using AWG4 = 21 mm

heavier cable. Use ring crimp terminal cable to

connect to battery +. Apply silicon grease to the

fuse to prevent corrosion.

Use a fuse holder for ANL fuses

like the DLS FH2B. Fuse value

100 A if you use a AWG4 cable.

Connect the battery cable to the +12 Volt on the

amplifier. If you want to improve the power capacity

you can add a Power capacitor of 1 Farad in parallel

with the DC input. See the drawing on page 7.

Be sure to use a rubber grommet or a plastic

insulating tube where the cable passes the firewall

or other places when it can easily be jammed.

Use wire ties to secure to existing cables in the engine

room.

+12V REM GND

Protect

(Red)

Power

(Green)

Ground Terminal ( GND )

Important

Use either the low level or the high level input, do

not use both at same time.

Low level input

Use a pair of shielded stereo audio cables with RCA

type jack. Most trunk-mount amplifiers need a 20

feet RCA cable ( appr 5 – 6 meters). Most under the

seat installations require 12

feet ( 2 – 3 meters) RCA

cables. Avoid placing the RCA

cable close to speaker cables,

power cables and remote

control cable. Connect to in-

put socket A & B.

High Level Input

Connect left and right speaker wires coming from

the car stereo to the high level input as shown. You

must connect both plus and minus as the inputs are

balanced, connecting plus only gives lower level and

bad sound quality. By changing the polarity of plus

and minus, you can change the phase.

Hi level input plug on amp.

Automatic turn on when using high level input.

With the Hi/Low input swich set to Hi, the amplifier turns

on automatically on high input. You dont need to connect

a separate remote wire from your head unit.

When using High Level input:

Set the switch to position ”Hi / Level”

When using Low level input:

Set the switch to position ”Low / Level”

If the switch is set to wrong

position, the amplifier still

works, but the risk for

disturbances or distortion

increases.

Input and controls

Input Level control

Subsonic filter

The Subsonic filter blocks the very

deepest frequencies from reaching the

subwoofers. It has a variable frequency

from 15 to 50 Hz. A typical setting is

25-30 Hz.

Low Pass Filter

The LPF ( low pass filter ) allow low

frequencies only and blocks higher

frequencies. A typical setting is 60 – 80

Hz. Choose the setting that sounds best

in your car.

Phase control

The phase control can be set

continuously from 0 - 180 degrees. This

is very useful when you want to adjust

the bass sound for best front stage image.

Start on 0 and turn the control slowly

clockwise until you experience the bass

sound coming from the front.

You may have to change the polarity of

the speaker connection to get the best

result.

High Input

White : A ch.+

White/Black : A ch.-

Grey/Black : B ch.-

Grey : Bch.+

Input Wiring

Inputs may be low level from the RCA output of the

car stereo or high level from the car stereo speaker

output.Low level = RCA is to prefer for the best sound

quality.

Subsonic

15Hz 50Hz

LPF

15Hz 150Hz

The input level control, 5V – 0,15 V,

matches the output of your radio to the

input of the amplifier. After installation

is complete, make sure the input of the

amplifier is turned down all the way (

counter-clockwise at 5V ). Play a tape

or CD, make sure all bass or treble

settings or equalizer are flat, and turn

the volume of the radio up until you

just start to hear distortion. Turn the

volume control down just a bit. On the

amplifier increase the input level control

( clockwise or to the right ) until you just

start to hear distortion, then back the

level control just a bit. Now your radio

and amplifier levels are matched.

Level

5 V 0,15 V

Phase

180

Hi / Level

Low / Level

CAD11

Bass boost control is used to set

the bass volume. You can select the

amplification between 0 dB and +18

dB at a 45 Hz center frequency.

This function is used to compensate

for the bass box function and to adjust

for your own taste of bass. Set level

control at 0 dB if you want it to be

inoperative.

Bass boost control on CAD11

RCA Output

Use RCA Outputs to

connect additional

amplifiers.

Ouput Input

Single amplifier system

You can fine tune your bass level

from the front of your car. Connect

the external bass level control box to

the remote socket on the rear panel.

Remote Bass level control

Bass Level

Remote

Testing

Before you finish the installation, you should do the

following tests to make sure the wiring is correct

and everything is operating properly.

Test power wiring

1. Turn on the head unit but do not turn up the

volume. The amplifier power light should

come on. If not, check the remote and +12

volt wires. Also check the ground

connection.

2. Turn up the head units volume slightly. All

speakers should operate. if not, check

wiring connections at amplifier and

speakers.

The Subsonic filter at 25-30 Hz and the LPF filter

setting at 60-80 Hz.

Filter settings

From low level

output of head unit

To input of

additional amps.

Reconnect Battery

When wiring is complete,

reconnect the battery

negative terminal.

NOTE!

Minimum speaker load is one (1) ohm. You can

connect four 4 ohm subwoofers or two 2 ohm

subwoofers to the amplifier. Loads or speaker

impedances less than 1 ohm could result in poor

sound quality and/or damage to amplifier.

Master / Slave switch

must be set to Master

Connection of DC-input and Remote level control,

see page 7.

Bass

Boost

0 dB 18 dB

Subsonic

15Hz 50Hz

LPF

15Hz 150Hz

CAD11

Bridging two amplifiers

Remote bass

level control.

To Remote on

head unit

GROUND

Battery

Fuse

Distribu-

tion block

Power Cap

You can connect t two CAD11 in

bridge mode.

One of the amplifiers is ”Master”

that controls the signal to the

second amplifier that should be

used in ”Slave” position. The sig-

nal is fed through the Data link

connector. Connect the

amplifiers as in the drawings

below.

Master slave selector & Data link

connection

Data

Link

Speaker

impedance:

4 ohm/2 ohm

From low level

output of head unit

Bridged

mode

Master

Slave

Bridged

mode

Master

Slave

Bridged

mode

Master

Slave

Bridged switch:

Slave position

Bridged switch:

Master position

Connection of DC-input and Remote sub level control

Connecting two CAD11 in bridge mode will dou-

ble the output power. Minimum speaker load is

then 2 ohms. The output power with a 4 ohm

load is 1500 Watts, and with 2 ohm load 2000

Watts. The RCA signal must be connected only

to the amplifer set to run as ”Master”.

The filters as well as the level control is only

working on the ”Master” amplifier.

Bridging two amplifiers can be done only

between amplifiers of the same model

Modular 4-pole cable to connect

between Data Link sockets

NOISE PROBLEMS

WHINING NOISE VARYING WITH ENGINE

REVOLUTIONS:

Do this:

1. Rewire the power supply (12 V) to source

unit direct from battery.

2. Rewire ground wire from source unit to

clean position on chassis.

3. Check all power connections to ensure that

they are clean and tight.

4. Check quality of system ground connection.

5. Install a Power Cap capacitor. This can be

helpful against most noise problems.

CONSTANT WHINING NOISE:

Do this:

1. Ensure that all equipment has a common

ground point.

2. Check quality of earth strap connection from

battery negative terminal to chassis.

3. Disconnect signal cables from amplifier to

see if noise disappears. If so the leads are

picking up noise. Test this by laying a new

cable over the seats and reconnecting to the

amplifier. If the noise does not return, re-

route original cable away from source of

interference.

If noise remains regardless of cable position,

try to use so called Quasi-balanced signal

cables. DLS PRO or ULTIMATE cables are

quasibalanced.

SPEAKER POLARITY CHECK.

All speakers in a car audio system should be

connected in phase (the same polarity). All spea-

ker cones must move in the same direction. Out of

phase speakers will cause a lack of bass, and a

poor stereo soundstage.

Checking polarity:

Hold the - connection of the speaker wire to the -

terminal of a 1,5 Volt flashlight battery. Tap the +

wire on to the + terminal of the battery, and observe

the movement of the cone. The cone should move

outwards when the wire touches the battery, and

inwards when the battery is removed. If it is the

other way around, the speaker has been connected

backwards and it must be removed and connected

correctly.

If your system also has a subwoofer connected

through a passive 6 or 12 dB crossover, try to

connect this with various polarity and judge what

sounds best. The phase shift in passive crossovers

sometimes makes it necessary to change polarity.

Battery

1,5 Volt

Professional Tip:Professional Tip:

Professional Tip: Professional Tip:

Installing in trunk

When installing the amplifier in the trunk, run the

power wires along the same path as the other

vehicle wiring. Many cars have insulated channels

for wiring. you will have to remove the door sill trim

and the carpet.

Securing wires

Use wire ties to bundle together when possible.

(But never bundle speaker wires or signal cables

together with power wires.

Professional Tip:

Speaker and power wires

Do not run speaker and power wires next to each

other. Power wires can generate a ”siren” sound in

the speakers. Runs speaker and power wires on

opposite sides of the car.

Crimp connections

Purchase crimp connectors and crimping tool.

Connectors are color coded.

1. Strip 1/4 inch (6 mm) of insulation from the wire.

2. Insert into connector

3. Crimp tightly

CAD11

DLS Svenska AB - 2004-09-09

DLS DLS CAD11 Owner's manual

Brand: DLS

Model: DLS CAD11

Category: Musical Equipment

Type: Owner's manual

This manual is also suitable for

CLASSIC CAD11

Download PDF

report

DLS DLS CAD11 Owner's manual

This manual is also suitable for

DLS DLS CAD11 Owner's manual

Related papers

Other documents