Horizon Fitness RE7.6 User manual

ELLIPTICAL ASSEMBLY &

USER’S GUIDE

FOR MODEL :

RE7.6

BEFORE

YOU BEGIN

ASSEMBLYASSEMBLY

3

INTRODUCTION

IMPORTANT

PRECAUTIONS

ELLIPTICAL

OPERATION

CONDITIONING

GUIDELINES

TROUBLESHOOTING

& MAINTENANCE

LIMITED

WARRANTY

INTRODUCTION

CONGRATULATIONS and THANK YOU for your purchase of this Horizon Fitness elliptical!

Whether your goal is to win races or simply enjoy a fuller, healthier lifestyle, a Horizon Fitness elliptical

can help you attain it – adding club-quality performance to your at-home workouts, with the ergonomics

and innovative features you need to get stronger and healthier, faster. Because we're committed to

designing fitness equipment from the inside out, we use only the highest quality components. It's a

commitment we back with one of the strongest frame-to-brake warranty packages in the industry.

You want exercise equipment that offers the most comfort, the best reliability and the highest quality

in its class.

Horizon Fitness delivers.

INTRODUCTION

TABLE OF CONTENTS

Important Precautions

Assembly

Before You Begin

Elliptical Operation

Conditioning Guidelines

Troubleshooting & Maintenance

Limited Warranty

CONTACT INFORMATION

4

5

17

18

28

34

38

Back Cover

BEFORE

YOU BEGIN

4

INTRODUCTION ASSEMBLY

BEFORE

YOU BEGIN

ELLIPTICAL

OPERATION

LIMITED

WARRANTY

TROUBLESHOOTING

& MAINTENANCE

CONDITIONING

GUIDELINES

ASSEMBLY

IMPORTANT

PRECAUTIONS

SAVE THESE INSTRUCTIONS

Read all instructions before using this elliptical. When using an electrical product, basic precautions

should always be followed, including the following: Read all instructions before using this elliptical. It is the

responsibility of the owner to ensure that all users of this elliptical are adequately informed of all warnings

and precautions. If you have any questions after reading this manual, contact Sears at the number listed

on the back cover of this manual.

IMPORTANT PRECAUTIONS

At NO time should pets or children under the age of 12 be closer to the elliptical than 10 feet.

At NO time should children under the age of 12 use the elliptical.

Children over the age of 12 should not use the elliptical without adult supervision.

It is essential that your elliptical is used only indoors, in a climate controlled room. If your elliptical has been

exposed to colder temperatures or high moisture climates, it is strongly recommended that the elliptical is

warmed up to room temperature before first time use. Failure to do so may cause premature electronic failure.

To reduce the risk of burns, fire, electrical shock or injury to persons:

• If you experience any kind of pain, including, but not limited to chest pains, nausea, dizziness, or

shortness of breath, stop exercising immediately and consult your physician before continuing.

• Maintain a comfortable pace. Do not sprint above 80 rpms on this machine.

• To maintain balance, it is recommended to keep a grip on the handlebars while exercising, mounting or

dismounting the machine.

• Do not wear clothes that might catch on any part of the elliptical.

• Do not turn pedal arms by hand.

• Make sure handlebars are secure before each use.

• Do not insert or drop any object into any opening.

• Unplug elliptical before moving or cleaning it. To clean, wipe surfaces down with soap and slightly damp

cloth only; never use solvents. (See MAINTENANCE)

• This elliptical should not be used by persons weighing more than 250 pounds. Failure to comply will void

the warranty.

• This elliptical is intended for in-home use only. Do not use this elliptical in any commercial, rental, school

or institutional setting. Failure to comply will void the warranty.

• Do not use elliptical in any location that is not temperature controlled, such as but not limited to garages,

porches, pool rooms, bathrooms, car ports or outdoors. Failure to comply may void the warranty.

• Use the elliptical only as described in this manual.

WARNING

BEFORE

YOU BEGIN

ASSEMBLY

5

INTRODUCTION

ELLIPTICAL

OPERATION

CONDITIONING

GUIDELINES

TROUBLESHOOTING

& MAINTENANCE

LIMITED

WARRANTY

ASSEMBLY

IMPORTANT: READ THESE SAFETY INSTRUCTIONS BEFORE USE!

There are several areas during the assembly process of a elliptical that special attention must be paid. It is

very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened.

If the assembly instructions are not followed correctly, the elliptical could have frame parts that are not

tightened and will seem loose and may cause irritating noises. To prevent damage to the elliptical, the

assembly instructions must be reviewed and corrective actions should be taken.

UNPACKING

Unpack the product where you will be using it. Place the product on a level flat surface. It is recommended

that you place a protective covering on your floor. During each assembly step, ensure that ALL nuts and

bolts are in place and partially threaded in before completely tightening any ONE bolt.

NOTE: A light application of grease may aid in the installation of hardware. Any grease, such as lithium

bike grease is recommended.

Before proceeding, find your elliptical’s serial number

located on the front stabilizer tube and enter it in the

space provided below. Also locate the model name

which is located on the side cover badge.

ENTER YOUR SERIAL NUMBER AND

MODEL NAME IN THE BOxES BELOW:

SERIAL NUMBER :

MODEL NAME:

* Refer to the SERIAL NUMBER and MODEL NAME when calling for service.

WARNING

IMPORTANT

PRECAUTIONS

BEFORE

YOU BEGIN

6

INTRODUCTION

IMPORTANT

PRECAUTIONS

ASSEMBLY

BEFORE

YOU BEGIN

ELLIPTICAL

OPERATION

LIMITED

WARRANTY

TROUBLESHOOTING

& MAINTENANCE

CONDITIONING

GUIDELINES

TOOLS INCLUDED PARTS INCLUDED

c 5mm Allen Wrench

c 6mm Allen Wrench

c Phillips Screw Driver

c 13/15mm Flat Wrench

c 1 Console

c 1 Console Mast

c 1 Front Stabilizer Tube

c 2 Upper Handlebars

c 2 Lower Handlebars

c 2 Lower Link Arms

c 2 Pivoting Foot Pads

c 2 Top Covers

c 1 HORIZON FITNESS

12-volt Power Supply

CONSOLEUPPER HANDLEBAR

MAIN FRAME

LOWER HANDLEBAR

LOWER LINK ARM

ELBOW COVER

FRONT STABILIZER TUBE

FAN

GRIP PULSE

CONSOLE MAST

TOP COVER

PIVOTING FOOT PAD

PEDAL ARM

WHEEL COVER

c 2 Handlebar Covers

c 5 Hardware Bags

c 2 Elbow Covers

c Water Bottle Cage

HANDLEBAR COVER

If you have questions or if there are any missing parts, contact 1-800-4-MY-HOME

®

.

Further contact information is located on the back cover of this manual.

For a complete exploded diagram, see Quick Start and Parts Guide (included in User’s Guide bag).

BEFORE

YOU BEGIN

ASSEMBLY

7

INTRODUCTION

IMPORTANT

PRECAUTIONS

ELLIPTICAL

OPERATION

CONDITIONING

GUIDELINES

TROUBLESHOOTING

& MAINTENANCE

LIMITED

WARRANTY

FRONT STABILIZER TUBE

BOLT (A)

SPRING WASHER (B)

WASHER (C)

MAIN FRAME

ASSEMBLY STEP 1

A) Open HARDWARE BAG FOR STEP 1.

B) Attach the FRONT STABILIZER TUBE to the MAIN FRAME using 2 BOLTS (A), 2 SPRING WASHERS (B) and 2 FLAT

WASHERS (C).

#0-5"

NN

2UZ

413*/(8"4)&3#

NN

2UZ

'-"58"4)&3$

NN

2UZ

HARDWARE BAG FOR STEP 1 CONTENTS :

BEFORE

YOU BEGIN

8

INTRODUCTION

IMPORTANT

PRECAUTIONS

ASSEMBLY

BEFORE

YOU BEGIN

ELLIPTICAL

OPERATION

LIMITED

WARRANTY

TROUBLESHOOTING

& MAINTENANCE

CONDITIONING

GUIDELINES

ASSEMBLY STEP 2

MAIN FRAME

CONSOLE WIRES

BOLT (A)

SPRING WASHER (B)

FLAT WASHER (C)

CONSOLE MAST

CONSOLE MAST GROMMET

A) Open HARDWARE BAG FOR STEP 2.

B)

Carefully pull the CONSOLE WIRES through the CONSOLE MAST using the twist tie located inside the

CONSOLE MAST.

C) Attach the CONSOLE MAST to the MAIN FRAME using 4 BOLTS (A), 4 SPRING WASHERS (B) and 4 FLAT

WASHERS (C).

BOLT (A)

20 mm

Qty: 4

SPRING WASHER (B)

18 mm

Qty: 4

FLAT WASHER (C)

20 mm

Qty: 4

HARDWARE BAG FOR STEP 2 CONTENTS :

BEFORE

YOU BEGIN

ASSEMBLY

9

INTRODUCTION

IMPORTANT

PRECAUTIONS

ELLIPTICAL

OPERATION

CONDITIONING

GUIDELINES

TROUBLESHOOTING

& MAINTENANCE

LIMITED

WARRANTY

MAIN FRAME

CONSOLE

MAST

GROMMET

FRONT TOP COVER

REAR TOP COVER

D) Insert the FRONT TOP COVER, followed by the REAR TOP COVER and snap them together.

E) Slide CONSOLE MAST GROMMET down to seal the console mast hole.

BEFORE

YOU BEGIN

10

INTRODUCTION

IMPORTANT

PRECAUTIONS

ASSEMBLY

BEFORE

YOU BEGIN

ELLIPTICAL

OPERATION

LIMITED

WARRANTY

TROUBLESHOOTING

& MAINTENANCE

CONDITIONING

GUIDELINES

ASSEMBLY STEP 3

CONSOLE MAST

LOWER HANDLEBAR

PRE-ATTACHED

BOLT & WASHER

UPPER HANDLEBAR

PRE-ATTACHED

SET SCREWS

USE RIGHT HANDLEBARSUSE LEFT HANDLEBARS

NOTCH

TAB

After handlebars are assembled they will rotate freely – be cautious. Until the

machine is fully assembled, do not grab the handlebars for support.

NOTE: There is NO hardware bag for this step. All hardware is pre-installed.

A) Remove PRE-ATTACHED BOLT & WASHERS from CONSOLE MAST.

B) Slide LOWER HANDLEBARS onto CONSOLE MAST and attach by re-inserting PRE-ATTACHED BOLT & WASHERS.

C) Slide UPPER HANDLEBARS onto LOWER HANDLEBARS and align NOTCH with TAB making sure handlebars are

joined together completely. Secure UPPER HANDLEBARS to LOWER HANDLEBARS using PRE-ATTACHED SET

SCREWS.

WARNING

Reminder: The upper and lower handlebars are marked with an L if they are to be used on the left-hand side

of the elliptical or an R if they are to be used on the right-hand side of the elliptical. If the handlebars are

assembled on the incorrect side of the elliptical, the unit will not function correctly.

BEFORE

YOU BEGIN

ASSEMBLY

11

INTRODUCTION

IMPORTANT

PRECAUTIONS

ELLIPTICAL

OPERATION

CONDITIONING

GUIDELINES

TROUBLESHOOTING

& MAINTENANCE

LIMITED

WARRANTY

ASSEMBLY STEP 4

BACK HANDLEBAR COVER

FRONT HANDLEBAR COVER

UPPER HANDLEBAR

NOTE: There is NO hardware bag for this step.

A) Snap the front and back HANDLEBAR COVERS together onto the UPPER HANDLE BARS.

Note the position of the snap tabs on the covers before snapping into position.

B) Repeat on other side.

BEFORE

YOU BEGIN

12

INTRODUCTION

IMPORTANT

PRECAUTIONS

ASSEMBLY

BEFORE

YOU BEGIN

ELLIPTICAL

OPERATION

LIMITED

WARRANTY

TROUBLESHOOTING

& MAINTENANCE

CONDITIONING

GUIDELINES

ASSEMBLY STEP 5

GUIDE RAIL

TEFLON WASHERS (E)

NUT (G)

BOLT (D)

LOWER LINK ARM

SPACER (F)

LOWER LINK ARM

SPACER

TEFLON WASHERS

LOWER

HANDLEBAR

A) Open HARDWARE BAG FOR STEP 5.

B) Slide SPACER (F) into LOWER HANDLEBAR.

C) Place TEFLON WASHERS (E) on either side of SPACER (F). While holding TEFLON WASHERS (E) slide LOWER

LINK ARM into bottom end of LOWER HANDLEBAR.

D) Insert BOLT (D) into LOWER HANDLEBAR and secure using NUT (G).

E) Repeat on other side.

NYLON NUT (G)

INSIDE DIAMETER:

8 mm

Qty: 2

BOLT (D)

60 mm

Qty: 2

SPACER (F)

44 mm axis

Qty: 2

TEFLON WASHER (E)

24 mm

Qty: 4

HARDWARE BAG FOR STEP 5 CONTENTS :

BEFORE

YOU BEGIN

ASSEMBLY

13

INTRODUCTION

IMPORTANT

PRECAUTIONS

ELLIPTICAL

OPERATION

CONDITIONING

GUIDELINES

TROUBLESHOOTING

& MAINTENANCE

LIMITED

WARRANTY

ASSEMBLY STEP 6

LOWER LINK ARM

PEDAL ARMS

SPACER (H)

BOLT (I)

FLAT WASHER (J)

SPLIT TEFLON

WASHER (M)

FOOTPLATE TUBE

SPLIT TEFLON

WASHER (M)

U BRACKET

A ) Open HARDWARE BAG FOR STEP 6.

B) Align LOWER LINK ARM with U BRACKET.

CAUTION:

Be careful to keep the LOWER LINK ARM aligned with guide rail. Do not twist it to the left or right

while positioning it on the U BRACKET.

C) Slide SPACER (H) through U BRACKET and FOOTPLATE TUBE.

D) Insert FLAT WASHER (J) and BOLT (I) into outside end of FOOTPLATE TUBE.

E) Insert 2 SPLIT TEFLON WASHERS (M) on left and right sides of FOOTPLATE TUBE and tighten BOLT (I).

F) Repeat on other side.

BOLT (I)

15 mm

Qty: 2

SPACER (H)

70 mm axis

Qty: 2

FLAT WASHER (J)

35 mm

Qty: 2

SPLIT TEFLON WASHER (M)

24 mm

Qty: 4

HARDWARE BAG FOR STEP 6 CONTENTS :

BOLT (I)

FLAT WASHER (J)

FOOTPLATE TUBE

SPACER (H)

SPLIT TEFLON

WASHER (M)

U BRACKET

TOP VIEW OF LEFT FOOT PAD

INSERT

SPACER

THIS

DIRECTION

BEFORE

YOU BEGIN

14

INTRODUCTION

IMPORTANT

PRECAUTIONS

ASSEMBLY

BEFORE

YOU BEGIN

ELLIPTICAL

OPERATION

LIMITED

WARRANTY

TROUBLESHOOTING

& MAINTENANCE

CONDITIONING

GUIDELINES

SCREW (L)

15 mm

Qty: 2

SCREW (K)

10 mm

Qty: 2

HARDWARE BAG FOR STEP 7 CONTENTS :

ASSEMBLY STEP 7

LOWER HANDLEBAR

INSIDE

ELBOW COVER

OUTSIDE

ELBOW COVER

SCREW (L)

SCREW (K)

WATER BOTTLE CAGE

LOWER LINK ARM

A) Open HARDWARE BAG FOR STEP 7.

B) Attach the OUTSIDE ELBOW COVER to elbow joint using 1 SCREW (K).

C) Snap the INSIDE ELBOW COVER onto the OUTSIDE ELBOW COVER.

Note the position of the snap tabs before snapping into position.

D) Repeat on other side.

E) Install WATER BOTTLE CAGE to console mast using 2 SCREWS (L).

BEFORE

YOU BEGIN

ASSEMBLY

15

INTRODUCTION

IMPORTANT

PRECAUTIONS

ELLIPTICAL

OPERATION

CONDITIONING

GUIDELINES

TROUBLESHOOTING

& MAINTENANCE

LIMITED

WARRANTY

ASSEMBLY STEP 8

CONSOLE

CONSOLE MAST

CONSOLE WIRES

PRE-ATTACHED

SCREWS

NOTE: There is NO hardware bag for this step. All hardware is pre-installed.

A) Attach the CONSOLE MAST wires to the CONSOLE wires .

B) Carefully tuck the CONSOLE MAST wires into the CONSOLE MAST before attaching the CONSOLE.

C) Attach CONSOLE to the CONSOLE MAST using the 4 PRE-ATTACHED SCREWS (screws will have to be removed

from the console first).

DO NOT PINCH WIRES!

BEFORE

YOU BEGIN

16

INTRODUCTION

IMPORTANT

PRECAUTIONS

ASSEMBLY

BEFORE

YOU BEGIN

ELLIPTICAL

OPERATION

LIMITED

WARRANTY

TROUBLESHOOTING

& MAINTENANCE

CONDITIONING

GUIDELINES

YOU’RE FINISHED!

RE7.6

BEFORE

YOU BEGIN

ASSEMBLY

17

INTRODUCTION

IMPORTANT

PRECAUTIONS

ELLIPTICAL

OPERATION

CONDITIONING

GUIDELINES

TROUBLESHOOTING

& MAINTENANCE

LIMITED

WARRANTY

BEFORE

YOU BEGIN

ASSEMBLY

BEFORE YOU BEGIN

CONGRATULATIONS! on choosing your elliptical. You’ve taken an important step in developing and

sustaining an exercise program! Your elliptical is a tremendously effective tool for achieving your personal

fitness goals. Regular use of your elliptical can improve the quality of your life in so many ways.

HERE ARE JUST A FEW OF THE HEALTH BENEFITS OF EXERCISE:

• Weight Loss

• A Healthier Heart

• Improved Muscle Tone

• Increased Daily Energy Levels

The key to reaping these benefits is to develop an exercise habit. Your new

elliptical will help you eliminate obstacles that prevent you from exercising.

Inclement weather and darkness won't interfere with your workout when you

use your elliptical in the comfort of your home. This guide provides you with

basic information for using and enjoying your new machine.

LOCATION OF THE ELLIPTICAL

Place the elliptical on a level surface. There should be 6 feet of clearance

behind the elliptical, 3 feet on each side and one foot in front for the power

cord (See diagram to the right). Do not place the elliptical in any area that

will block any vent or air openings. The elliptical should not be located in a

garage, covered patio, near water or outdoors.

GFFU

GFFU

GFFU

GPPU

BEFORE

YOU BEGIN

18

INTRODUCTION

IMPORTANT

PRECAUTIONS

ASSEMBLY

BEFORE

YOU BEGIN

ELLIPTICAL

OPERATION

LIMITED

WARRANTY

TROUBLESHOOTING

& MAINTENANCE

CONDITIONING

GUIDELINES

ASSEMBLY

ELLIPTICAL

OPERATION

POWER

Your programmable elliptical is powered by a power supply. The power must be plugged into the power jack,

which is located in the front of the machine near the STABILIZER TUBE. Make sure the console power switch is

in the ON position.

Do not operate the elliptical if the power cord or plug is damaged.

If the elliptical appears to not be working properly, do not use the elliptical.

MOVING

Your elliptical has a pair of transport wheels built

into the FRONT STABILIZER TUBE. To move, first

remove the power supply and firmly grasp the

CONSOLE MAST, carefully tilt and roll.

Our ellipticals are well built and heavy, weighing up to 200 lbs! Use care and

additional help if necessary when moving.

FOOT POSITIONING

Your elliptical offers a variety of foot positions. Moving your foot to the forward most position of the foot pad

increases your step height, which will create a feel similar to a step machine. Placing your foot toward the back

of the foot pad decreases your step height and creates more of a gliding feel, similar to a smooth walk or run.

Your elliptical also allows you to pedal both forward and backwards to offer a variation to your workout and to

focus on other major leg muscle groups such as your hamstrings and calves.

ELLIPTICAL OPERATION

WARNING

BEFORE

YOU BEGIN

ASSEMBLY

19

INTRODUCTION

IMPORTANT

PRECAUTIONS

ELLIPTICAL

OPERATION

CONDITIONING

GUIDELINES

TROUBLESHOOTING

& MAINTENANCE

LIMITED

WARRANTY

ELLIPTICAL

OPERATION

ASSEMBLY

A) ADjUSTABLE MONITOR DISPLAY: RPM, Time, Distance, Calories, Pulse, Resistance.

B) PROGRAM MATRIx: Displays program profiles and scrolling messages.

C) START/STOP: Press to start/pause/end your workout. Hold for 3 seconds to reset the elliptical.

D) PROGRAM KEYS: Used to select your program (Manual, Intervals, Random, Weight Loss, Rolling, Reverse Train,

THR Zone, Custom).

E) +/- KEYS: Used to adjust program settings.

F) ENTER: Used to confirm settings.

G) RESISTANCE UP/DOWN KEYS: Used to adjust resistance.

H) ONE-TOUCH RESISTANCE KEYS: Used to reach desired resistance more quickly.

I) BEEP ON/OFF: Used to turn off indicator sound.

j) FAN KEY: Used to adjust fan to 3 speed levels.

K) FAN: Personal workout fan.

L) USER FAVORITE KEYS: Retains a user’s favorite program settings in memory.

RE7.6 CONSOLE DISPLAY

TIME DISTANCE RESISTANCE

RPM

CALORIES

PULSE

Resistance

Favorite

1

Start/Stop

Hold to R ese t

Favorite

2

C

U

S

T

O

M

W

E

I

G

H

T

L

O

S

M

A

N

U

A

L

R

O

L

I

N

G

I

N

T

E

R

V

A

L

S

R

E

V

E

R

S

E

T

R

A

I

N

T

H

R

Z

O

N

E

R

A

N

D

O

M

BEEP

ON/OFF

ENTER

2

10

16

8

14

6

12

4

A

B

D H

I

F

G

K

E

CJL

BEFORE

YOU BEGIN

20

INTRODUCTION

IMPORTANT

PRECAUTIONS

ASSEMBLY

BEFORE

YOU BEGIN

ELLIPTICAL

OPERATION

LIMITED

WARRANTY

TROUBLESHOOTING

& MAINTENANCE

CONDITIONING

GUIDELINES

ASSEMBLY

ELLIPTICAL

OPERATION

1) Select THR ZONE program (P7) using the PROGRAM KEYS and press ENTER.

• The CALORIES/PULSE window will flash showing the default target heart rate of 80 beats per minute.

2) Set TARGET HEART RATE (from the chart on page 29) using the +/- KEYS and press ENTER.

*NOTE: Target beats per minute is selected in intervals of 5

3) Select TIME using the +/- KEYS and press START to begin the program.

NOTES:

1) There is a 4-minute warm-up built into this program at level 1 resistance.

2) After 4 minutes the resistance will automatically adjust to bring your heart rate within 5 beats of the

target number you selected at the beginning of the program.

3) If there is no Heart Rate detected, the resistance will not change.

4) If your Heart Rate is 25 beats over your Target Zone the program will shut down.

5) There is a 4-minute cool-down built into this program.

SELECTING THR ZONE PROGRAM

RE7.6 CONSOLE OPERATION

1) Turn on Elliptical.

2) Press START button and begin exercising.

3) Program will automatically default to MANUAL (P1), the time will count up from 0:00 and the resistance

will default to level 1.

4) The resistance level can be adjusted during the workout.

QUICK START

SELECTING PROGRAMS

1) Select a program using the PROGRAM KEYS and press ENTER.

*NOTE: If you press START, the program will begin and count down from 30:00. The program defaults

to level 1.

2) Select a LEVEL using the +/- KEYS and press ENTER.

3) Set TIME using the +/- KEYS and press START to begin the program.

• Count-down range is 20:00 to 99:00 minutes (except MANUAL which can be set for 5:00 to 99:00)

– Select desired time and press ENTER.

Page is loading ...

Horizon Fitness RE7.6 User manual

This manual is also suitable for

Horizon Fitness RE7.6 User manual

Related papers

Other documents