SYSTEM CAMERA PARKING
GUIDELINES
IP67
WEATHER
PROOF
SPECIFICATIONS
- 1/4” Full Colour CMOS Imaging Clip
- PC7070 Imaging Sensor
- Full Glass Lens
- 110° Wide Viewing Angle (Horizontal)
- 170° Wide Viewing Angle (Diagonal)
- PAL/NTSC (Switchable)
- Parking Guidelines (Selectable), Type, Height & Width (Adjustable)
- One Button Control of Image Orientation, Video Mode Select, Guideline Type,
Guideline Height & Guideline Width
- Mirror, Normal, Upside-Down Mirror, Upside-Down Normal Image Orientation (Switchable)
- 0.3 Lux Minimum Illumination
- IP67 Water/Dust Protection
- 12/24V DC Power Input
- Number Plate or In-Bumper Mounting
- RCA Connection
- Dimensions: 16.5mm x 23mm (D)
INCLUDED:
- Dual Mounting Heads (Butterfly and Bumper Fit)
- Installation Manual
- Installation Hardware
- Metal Hole Saw for Bumper Fit Installation
- 6m Video Cable (RCA M)
2
WARRANTY
YEAR
12
24
SWITCHABLE
Bumper Fit Mounting
mp
er Fit Mountin
g
23mm
23mm
16.5mm
16
.
5
mm
23mm
16.5mm
CAR REARVIEW CAMERA
GENERAL:
After installation, the rear view system will automatically activate when reverse
gear is selected. This can provide a clear image for the driver and protect children,
pedestrians etc from injury. Also your vehicle will avoid costly repairs from dents
and other damage when parking.
CAMERA:
7KH'8$/+($'V\VWHPLQFOXGHGZLWK\RXUSXUFKDVHDOORZVIRUÀH[LEOHLQVWDOODWLRQ
RSWLRQVHLWKHUVXUIDFHPRXQWHJQXPEHUSODWHRUERRWOLGRUVWHDOWKLQVHUWPRXQW
HJEXPSHU
7KH5&$YLGHRFDEOHVLPSO\FRQQHFWVZLWKPRVWDIWHUPDUNHW/&'PRQLWRUV
CAUTION:
3URWHFWLYH¿OPLIDWWDFKHGVKRXOGEHUHPRYHGIURPFDPHUDEHIRUHRSHUDWLRQ
Carefully check the +/- wiring sequence during installation.
Ensure safety when installing wires near the fuel tank
INSTALLATION:
'HWHUPLQHLQVWDOODWLRQORFDWLRQXVXDOO\WKHFHQWUHUHDURIYHKLFOH
D%XWWHUÀ\7\SH0RXQWRQVXUIDFHXVLQJGRXEOHVLGHGWDSHRUVFUHZV
E,QVHUW7\SH&DUHIXOO\GULOOKROHKROHVDZVXSSOLHGLQEXPSHULQVHUWFDPHUD
&RQQHFW5('FDEOHWR9SRZHUFDEOHRI5HYHUVLQJ/LJKWFLUFXLW
&RQQHFW%/$&.FDEOHWRJURXQG
&RQQHFWVLJQDOH[WHQVLRQFDEOH
&RQQHFW5&$<(//2:YLGHRFDEOHWR/&'PRQLWRU
CAR REARVIEW CAMERA
CAMERA ASSEMBLY OPTIONS:
7KH&6\VWHPLVVXSSOLHGZLWK'XDO0RXQWLQJ+HDGV:LQJ%XWWHUÀ\RU%XPSHU)LW
See diagram below:
b) Bumper Fit Assembly
l
ow:
1-click, enter with / without Guide Line switching mode;
THE FOLLOWING MODES MUST BE OPERATED UNDER THE MODE WITH GUIDE
LINE, operate to enter any mode you want 3 seconds after the previous mode.
2-quick-continuous click, enter Mirror / Non-mirror switching mode;
3-quick-continuous click, enter PAL / NTSC switching mode;
4-quick-continuous click, enter Guide Line Type selecting mode;
5-quick-continuous click, enter the Guide Line Width adjusting mode;
6-quick-continuous click, enter the Guide Line Height adjusting mode.
CABLE CONNECTIONS:
See wiring diagram below:
Camera
GND
+12/24V
(Red Cable connect to rear lamp positive)
F
F
M
M
Monitor
+
One-Button
Control
Monitor Trigger Wire
(Please insulate if not used)
Selectable - Guidelines, PAL/NTSC & Normal/Mirror Image
ONE-BUTTON CONTROLLER OPERATION GUIDE:
-
1
-
2
-
3
-
4
