Intellinet 523431 User manual

INT-523431-UM-1106-02

2

TABLE OF CONTENTS

Section 1: Introduction......................................................................................... 3

1.1 Warnings .................................................................................................... 3

1.2 Package Contents...................................................................................... 3

1.3 Specifications ............................................................................................. 3

Section 2: Installation .......................................................................................... 6

2.1 Before Installation ...................................................................................... 6

2.2 Installation .................................................................................................. 6

Section 3: Local Computer Setup ....................................................................... 8

3.1 Windows 2000 Setup ................................................................................. 8

3.2 Windows XP Setup.....................................................................................13

Section 4: Router Setup ......................................................................................17

4.1 Start Internet Explorer to Log In ................................................................17

4.2 PPPoE Configuration .................................................................................18

4.3 Dynamic IP (Cable Modem) Configuration................................................22

4.4 Static IP Configuration ...............................................................................24

4.5 Status..........................................................................................................26

4.5.1 WAN Status..........................................................................................26

4.5.2 Wireless Status ....................................................................................27

4.5.3 LAN Status ...........................................................................................28

4.6 Basic Setup ................................................................................................29

4.6.1 WAN Setup...........................................................................................29

4.6.2 Wireless Setup .....................................................................................30

4.6.3 LAN Setup............................................................................................31

4.6.4 Link Setup/Info .....................................................................................33

4.6.5 Routing Table.......................................................................................35

4.7 System........................................................................................................36

4.7.1 Administrator Setup .............................................................................36

4.7.2 Firmware Upgrade ...............................................................................37

4.7.3 System Log ..........................................................................................39

4.7.4 Miscellaneous Configurations..............................................................40

4.8 QoS.............................................................................................................42

4.8.1 Basic Setup ..........................................................................................42

4.8.2 IP QoS ..................................................................................................42

4.8.3 Application QoS ...................................................................................43

4.8.4 Ports QoS.............................................................................................44

4.9 NAT.............................................................................................................45

4.9.1 Applications..........................................................................................45

4.9.2 Internal Server......................................................................................48

4.9.3 Port Forwarding....................................................................................50

4.9.4 Port Trigger ..........................................................................................51

4.9.5 NAT On/Off...........................................................................................52

4.10 Advanced Setup.......................................................................................53

4.10.1 Firewall ...............................................................................................53

4.10.2 DDNS .................................................................................................54

3

4.10.3 WOL (Wake-on LAN).........................................................................55

4.10.4 URL Filter ...........................................................................................56

4.10.5 Remote Management ........................................................................57

4.10.6 Scheduler ...........................................................................................58

4.10.7 VPN ....................................................................................................58

Appendix A: UTP Cable Specifications ..............................................................60

Thank you for purchasing the INTELLINET™ NETWORK SOLUTIONS Wireless G

Broadband Router, Model 523431. This user manual includes hardware

specifications, installation guidelines, configuration guidelines and directions for

using the device.

1. INTRODUCTION

1.1 Warnings

• Only use the power adapter provided by manufacturer.

• Do not drop the router: It can damage the router’s electronic components.

• Do not disassemble the router. Doing so voids the warranty.

• Avoid extended exposure to sunlight to prevent overheating.

• Keep the router in a dry place and away from fire.

1.2 Package Contents

• Wireless G Broadband Router, Model 523431

• Switching DC Power Adapter (7.5 V, 1.5 A)

• RJ-45 Ethernet Cable

• User manual

1.3 Specifications

This Wireless G Broadband Router is a highly integrated device with many

functions, such as Gateway, Switch, DHCP server and Firewall.

11g 54 Mbps: Data rate support up to 54 Mbps for 802.11g; 11 Mbps for 802.11b.

Network Address Transform (NAT): With the provided Internet application, this

device allows more than one user to connect with the Internet at the same time by

sharing one public IP address. It supports many connection options: xDSL, cable

modem LAN/leased line and so on.

4 Ports 10/100 M Switch: Four 10/100 Mbps ports with MDI/MDI-X support (Auto

Uplink, which eliminates the need for using a crossover cable when connecting to a

different switch port).

PPPoE (ADSL) Automatic Disconnection/Connection: Users have the option of

choosing automatic disconnection based on idle time and re-connect on demand.

DHCP Server Supported: All of the networked computers can retrieve TCP/IP

settings automatically from this device.

4

Static IP Address Binding: Authorizes users to manage and configure a PC in

LAN in most cases by binding the MAC address and IP address together.

System Log: History of all activity.

UPnP: Supports Microsoft’s UPNP (Universal Plug and Play Service).

Web-Based Management: The router is easily and conveniently configured by any

standard Internet Web browser.

Internet Access Control: Different settings can be set up for different users.

Packet Filter: Port filter, IP address filter, MAC address filter, key word filter.

Virtual Server: Allows other users from the Internet to access WWW, the FTP

server or other servers in the LAN.

QoS (Quality of Service): Allows control of your Internet bandwidth. Set a

minimum bandwidth for a certain application, or limit the bandwidth an application

can consume. The router features IP- and port-based bandwidth control, as well.

Scheduler: Manage and control the Internet access for individual users.

DMZ Host: Set up one computer to operate in the Demilitarized Zone without any

firewall interference.

Remote Management: Remotely configure the router settings.

DDNS: Support for dynamic DNS services, such as www.dyndns.org.

Remote Wake-up: Remotely wake up PCs in the LAN.

Support VPN Pass-through: Supports VPN pass-through PPTP traffic. A user

connected to the device can establish outgoing connections to remote VPN servers.

VPN server: An integrated VPN server allows five simultaneous client connections.

ITEM

WIRELESS G BROADBAND ROUTER

Standards

IEEE 802.11g IEEE 802.11b; IEEE 802.3; IEEE 802.3u;

IEEE 802.3x

Protocols

TCP/IP, NAT, DHCP, UDP, FTP, PPPoE, PPTP, L2TP,

HTTP, DNS, IP Sec/VPN Pass-through

WAN

One 10/100 Mbps RJ-45 port, automatic

sense cross cable

External

Ports

LAN

Four 10/100 Mbps speed Ethernet

switch ports, auto sense cross cable

Frequency

Range

2.412 –2.472 GHz

Forward

Speed

1, 2, 5.5, 11 Mbps (802.11b)

6, 9, 12, 18, 24, 36, 48, 54 Mbps

(802.11g)

Opt.

Channel

14

Data

Modulation

CCK, DQPSK, DBPSK, OFDM

RF Power

16 – 18 dBm

SPECIFICATIONS

Wireless

Parameters

Antenna

Type

1*2.4 Ghz Dipole Antenna

1*2.4 Ghz Embedded Antenna

5

Cable

UTP 100Base-TX UTP/STP 5 or above standard

Control

interface

Based on Web application

Inside

functions

10/100 Mbps switch

LAN/WAN port auto sense cross cable

WAN port static/dynamic IP flexible setting up

Support 64/128 bit WEP and MAC

Support AP client Bridge-Point-to Point mode

Support client mode

PPPoE dial-up and connection time setting up

PPPoE dial-up and automatic/manual connection

Double IP configuration

Support VPN pass-through

DHCP service

DNS relaying

DMZ server

Static IP address binding

System memorandum forwarding

Broadband router configuration back-up

UPNP

Connection setting up and status

Time control on access to internet

Firewall

NAT On/Off

Port/IP/MAC/Key word filtration

Remote control

Remote wake-up

DDNS

Gateway

Virtual server

QoS & VPN server

CPU

KENDIN KS8695PX (ARM9)

FLASH

2MB Flash

Memory

16 MB SDRAM

LAN connection

Static or dynamic IP address

WAN connection

XDSL Cable Modem Special cable LAN

Power supply

DC 7.5 V / 1.5 A switch power adapter

Size

179 mm x *119mm x *39mm

Temperature

0 – 60°

Product Specifications

Humidity

10 – 85%

6

Compatible OS: Windows 95/98/Me/NT/2000/XP, Mac OS, Linux or other UNIX

system

Note: Features and specifications are subject to change without notice.

2. INSTALLATION

2.1 Before Installation

• First, confirm that your computer has a Java Script-capable Web browser

installed.

• Make sure that your computer has a LAN card installed and correctly configured

for TCP/IP.

• If using xDSL, you will need the username and password provided by your ISP.

NOTE: If your computer has ADSL PPPoE dial-up software installed, back up your

installation software and uninstall your ADSL PPPoE dial-up software before

proceeding with the installation.

2.2 Installation

1. Set up the WAN connection: Connect the broadband RJ-45 cable (xDSL, Cable

modem or LAN/leased cable) with the WAN port of the router.

2. Set up the LAN connection: Connect your computer’s LAN card port or your

switch’s UPLINK port with one LAN port of the router using a common network

cable. NOTE: All LAN ports of the router can automatically sense cross cable, so

straight-through or cross cable can be used to connect the LAN card or switch.

3. Turn on the power by pressing the power button on the back of the router. The

device will perform a self test. During the self test, the PWR LED, CPU LED,

Wireless LED and LAN port LEDs of connected ports are lit. After the self test, the

CPU LED starts flashing (on-off-on-off).

4. Start the computer.

7

LED

Description

Explanation

PWR

Power LED

Long light

CPU

System status LED

LED flashes (on-off-on-off) during normal

operation. Any other state indicates a

problem with the device.

WLAN

WLAN port

connection LED

ON, flashing during data transmission.

WAN

WAN port

connection LED

ON, flashing during data transmission.

LAN

LAN port

connection LED

Flashing refers to data transformation.

Port explanation

Antenna

Antenna provides wireless LAN functionality and

ensures optimal signal strength.

Power jack

Connect power adapter (7.5 V / 1.5 A)

Reset

Press the Reset button. Switch the power off/on.

After about 5 seconds, the RUN LED will flash

rapidly. Release the button. After router startup,

all configurations will be restored to the default

configuration.

WAN

Connect xDSL/cable modem or LAN cable.

LAN 1–4

Connect personal computers, hubs or switches.

PWR

CPU

WLAN

WAN

LAN 1–4

8

3. LOCAL COMPUTER SETUP

The Wireless G Broadband Router acts as a DHCP server, which means that it

provides IP addresses to all connected computers. By default, Windows, Linux and

Mac OS systems will try to obtain an IP address from a DHCP server, if present,

and no configuration of the computer’s IP settings are necessary. In order to test

your IP settings, simply start your computer while connected to the router. Then

open your Web browser and open http://192.168.10.1.

If the router’s Web Admin screen appears, you can skip this section and proceed

directly to Section 4.

If you are unable to open the router’s Web Admin screen, follow whichever

instructions below apply to the operating system you use.

3.1 Windows 2000 Setup

1. Install the Wireless G Broadband Router.

2. Start Windows 2000 and check whether the LAN LED is on or off. If off, confirm

the connection between the computer and the router is correct.

3. Click “Start” —> “Setting” —> “Control Panel.”

Antenna

Power Port

Reset

WAN

LAN 1 ~ 4

9

4. Double-click “Network and Dial-up Connection” in “Control Panel.”

5. Click “Local Area Connection” —> “Properties” —> “Internet Protocol (TCP/IP)”

and “Properties.”

10

6. Click the “General” tab; select “Obtain an IP address automatically” and “Obtain DNS server

address automatically.”

7. Click “OK.”

11

8. Click ”Start” —> “Run.”

9. Input ”cmd”; then click “OK.”

10. Input “ipconfig” in the pop-up command window.

NOTE: Make sure your IP is the same as that listed below. If it’s the same, then

your configuration is successful. If not, redo the above steps and restart your

computer.

• The IP address is between 192.168.10.2 and 192.168.10.254

• The subnet mask is 255.255.255.0

• The default gateway is 192.168.10.1 (the router’s default IP address)

10. Type “ping 192.168.10.1,” then hit “Enter.”

11. If you can see “Reply from 192.168.10.1: bytes=32 time=2ms TTL=64,” then the

connection between your computer and Broadband Router is completed.

12

13

3.2 Windows XP Setup

1. Install the Wireless G Broadband Router.

2. Start Windows XP and check whether the LAN LED is on or off. If off, confirm

that the connection between the computer and the router is correct.

3. Click “Start” —> “Setting” —> “Control Panel.”

4. Double-click “Network and Internet Connections” in “Control Panel.”

5. Click “Network Connection” —> “Local Area Connection” —> “Properties” —>

“Internet Protocol (TCP/IP)” and “Properties.”

6. Click “General“; select “Obtain an IP address automatically” and “Obtain DNS

server address automatically.”

7. Click “OK.”

14

15

16

8. Click “Start” —> “Run”; enter “cmd“; click “OK.”

9. Type “ipconfig” in the pop-up command window.

NOTE: Make sure the IP information is the same as shown below.

• The IP address is between 192.168.10.2 and 192.168.10.254

• The subnet mask is 255.255.255.0

• The default gateway is 192.168.10.1

17

11. Input “ping 192.168.10.1,” then “Enter.”

12. If you can see “Reply from 192.168.10.1: bytes=32 time=2ms TTL=64,” then the

connection between your computer and the router is completed.

4. ROUTER SETUP

4.1 Start Internet Explorer to Log In

1. Start your Web browser.

2. Enter “http://192.168.10.1” in the Web browser’s address bar. (192.168.10.1 is

the default IP address of the router.)

18

3. You will then see the following login Web page.

Click the “Login” button to enter the configuration and configure the router manually.

This may be required if the Internet Wizard or Wireless Wizard fail to detect the

settings automatically. The Internet Wizard lets you configure your Internet

connection quickly and conveniently. The Wireless Wizard helps you configure all

important wireless-related settings.

You can login directly without account and password confirmation because there is

no account information required by default. It is recommended that a password is

assigned immediately.

Conn. Type: The router’s current connection type. Dynamic IP (DHCP) is the

default value.

Conn. Status: The router’s current connection status.

WAN IP: The router’s current WAN (Internet) IP address.

Connected PC: The IP address of the computer that connects to the router.

4.2 PPPoE Configuration

This connection option is suitable for a virtual dial-up Internet connection.

1. Open the external ADSL modem and check the WAN LED of the router. If the

WAN LED is off, check the network cable between the external modem’s

LAN/Ethernet port and the router’s WAN port.

2. Click “Basic setup” —> “WAN setup” as shown.

19

3. Select the “PPPoE User (ADSL)” radio button.

4. Key in the “User ID” and “Password” provided by your Internet service provider.

5. Click the “Apply” button. You will then see the following pop-up window:

If “Conn. State” shows “Successfully connected,” the configuration is correct.

6. Click “Show Internet connection status” and proceed to section 4.5.1.

If “Conn. Status” shows “Invalid ID/password.” the configuration is incorrect. Click

the “Close” button and check your ID and password.

20

If “Conn. Status” is unchanged, check whether your service type is correct.

7. Confirm the WAN connection status: If the WAN connection is successfully

established, then by clicking “Show Internet Information” you can enter the WAN

status Web page; or click “Status” —> “WAN status” and verify the following.

• Connection Type should be PPPoE (ADSL)

• Connection Status should be “successfully connected”

• Physical Address shows the router’s WAN port MAC address.

• WAN IP Address, Subnet Mask, Default Gateway, Primary DNS Server and

Secondary DNS Server can be different from the following values. (These

addresses are provided by your ISP.)

Click “Disconnect” to disconnect from the Internet.

Page is loading ...

Intellinet 523431 User manual

Intellinet 523431 User manual

Related papers

Other documents