NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
INSTALLATION INSTRUCTIONS FOR DRIFTWOOD LOG KIT
[FOR USE WITH MODELS ALLUME™ 84 & ALLUME DLX 84, AND DRL4084 & DRL6084 FIREPLACES]
GENERAL INFORMATION
The driftwood log kit is to be used as a decorative addition to fireplace
models listed on this instruction sheet. Please read this instruction
sheet in its entirety before applying this log media kit.
ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND
OPERATION MANUAL PROVIDED WITH THE APPLIANCE APPLY
TO THESE INSTRUCTIONS.
Refer to the appliance installation instructions and care and opera-
tions manual (iico) for detailed instructions.
TURN OFF THE FIREPLACE AND ALLOW IT TO COMPLETELY COOL
BEFORE PROCEEDING.
TURN OFF GAS AND POWER TO THE APPLIANCE AND USE LOCK-
OUTS TO PREVENT ACCIDENTAL/UNSAFE OPERATION.
WARNING
Only use materials listed here. Only media authorized
have been tested for use within the fireplace and its
environment. Do not attempt to use any different
materials in the fireplace. Doing so may be dangerous
and will void the warranty and will result in incomplete
combustion, sooting, and poor flame quality.
WARNING
If media is not installed according to the installa-
tion instructions, flame impingement and improper
combustion could occur and result in soot and/or
excessive production of carbon monoxide (CO), a
colorless, odorless, toxic gas.
IMPORTANT NOTICE
GLASS MEDIA MUST BE INSTALLED BEFORE
INSTALLING LOG SET. LOG SET IS COMPATIBLE
WITH CRUSHED GLASS.
HEARTH PRODUCTS
KITS AND ACCESSORIES
P/N 901143-00
Rev. NC 03/2021
DRIFTWOOD LOG KIT
Cat. No. Model Kit Name
F4401 DRFTWD-LOG84 84” Driftwood Log Kit – Linear
Table 1 (see Figure 1)
Figure 1 - Kit Contents Overview
INSTALLER: Leave this manual with the appliance
CONSUMER: Retain this manual for future reference
KIT CONTENTS
1 ea. Driftwood Log Set
1 ea. Instruction Sheet
TOOLS NEEDED (NOT SUPPLIED)
1 pair of gloves - for handling fireplace media
Tape Measure
DRFTWD-LOG84 KIT
A
J
D
E
F
B
K
B
C
G
H
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Figure 2 - Placing Driftwood Logs
Innovative Hearth Products (IHP) reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue
colors, styles and products. Consult your local distributor for fireplace code information.
Printed in U.S.A. © 2021 Innovative Hearth Products
P/N 901143-00 Rev. NC 03/2021
IHP
1769 East Lawrence Street • Russellville, AL 35654
PREPARING THE FIREPLACE FOR DRIFTWOOD LOG SET
1. To access the glass door securing latches, first remove trim kit (if
installed) and screen barrier from fireplace.
2. Lift the barrier to clear the bottom channel and swing the bottom of
the barrier out. Then lower the barrier to clear the top channel.
3. Pull forward and upward on the door latch handles to unlatch the door.
4. Swing the top of the glass door away from the fireplace at about 15°
angle.
5. Carefully grip the door at the top and bottom, and remove it from the
fireplace. Place the door in a safe location for later re installation.
DRIFTWOOD LOG SET INSTALLATION
IMPORTANT: Reflective glass liners (if applicable) should be installed
before any glass media is installed.
IMPORTANT: Glass media is required. Logs cannot be installed without
glass media installed. Install glass media in an even layer and DO NOT
place on pilot cover. See care and operations manual for details.
IMPORTANT: This log set is designed to cross over the burner in places
without resting on the glass media. No part of any logs should rest
directly on glass media over burner to prevent soot accumulation and/
or poor flame quality.
NOTE: The area for installing logs measures 81” x 9-1/2”. All measurements
are taken from the left side of the firebox. For DRL6084 units with black
porcelain liners installed, subtract 1/2” from all dimensions.
NOTE: Dimensions indicate approximate location of each log. Some
adjustment may be necessary depending on gas type (NG or LP) and
appliance installation parameters.
NOTE: Refer to Figure 2 for placing Driftwood logs.
1. Place log G with forked end pointing toward the pilot and straddling
the burner. Front left (forked) end should be at 55-1/4”, and back
right end at 77”.
2. Place first log B with one end of fork resting on log G. Left end should
be at 62-3/4”, and right end at 79-3/4”.
3. Place log H at right end of firebox with tips resting on logs G and B
and curved section around the right edge of the burner.
4. Place log F near front of firebox with left end at 32”, and right end at
46-3/4”.
5. Rest notch on log E with notch on log F with log E extending over
the pilot cover slanted to the back right. Front left end should be at
37-3/4”, and back right end at 45”.
6. Place log D against back of firebox between log E and log G. Back
left end should be at 45-1/2”, and back right end at 57-1/2”.
7. Place log K with short straight section and knot near front of firebox
parallel to opening, and longer curved section extending over burner
with end resting in shallow dip on the top back part of log E. Front
right end should be at 56-1/2”, and back left end at 41-1/4”.
8. Place second log B near back of firebox with one end of fork just barely
resting on log E. Back right end should be at 41-1/2”, and back left
end at 24-3/4”.
9. Place log J against back of firebox with curved limb at right end
extending over burner to the front of firebox (about an inch from the
front lip). Right end should be at 27-3/4”.
10. Place log A parallel to front edge of firebox with left side curling around
left end of burner. Right end should be at 18-1/2”.
11. Complete installation by placing curved portion of log C on curved limb
of log J, angled slightly to back right and opposite end toward front left.
Angle should not be so severe that right end of log extends over burner.
Back right end should be at 29-1/4”, and front left at 18-1/4”.
Re-installing Glass Door, Barrier, and Trim
10. Retrieve the glass door. Visually inspect the gasket on the backside
of the frame. Gasket surface must be clean, free of irregularities and
seated firmly.
11. Re-install glass door by placing the bottom edge of the door assembly
into the door channel on the firebox. The tabs on the bottom of the
door on each side will fall into corresponding slots on the door channel
of the firebox.
12. Re-install the barrier by sliding it upward into the top barrier channel,
then push back slightly on the bottom, and lower it into the lower
barrier channel.
13. Re-install trim assembly - if applicable.
NOTE: Operate appliance for 30 minutes after log set installation to check
for significant impingement or sooting. Adjust logs as necessary to
minimize impingement if sooting is visible on logs.
NOTE: For DRL6084 units with
black porcelain liners installed,
subtract 1/2” from all dimensions.
29-1/4”18-1/4” 56-1/2”
18-1/2” 79-3/4”62-3/4”32”27-3/4” 37-3/4” 46-3/4”
45-1/2”41-1/4” 57-1/2”
55-1/4”45” 77”
24-3/4”
A
J
B
BD
K
C
E
F
GH
-
1
-
2
Astria Fireplaces DRL4000 Instruction Sheet
- Category
- Fireplaces
- Type
- Instruction Sheet
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Superior Fireplaces DRL6000 Operating instructions
-
-
-
-
-
-
Travis 430 Ember-Glo GSR2 Insert Fireplace Xtrodinair User manual
-
-
Kingsman Marquis Fireplaces MQVL60N, MQVL60NE, MQVL60NE2, MQVL60LP, MQVL60LPE, MQVL60LPE2 User manual
-
