Aquatica Harmony Duo-Wht Installation guide

Brand
Aquatica
Model
Harmony Duo-Wht
Type
Installation guide
Harmony Duo
Oval Freestanding Bathtub
Installation & Care Manual
USA and CANADA
www.aquaticaplumbing.com
E: [email protected]
Harmony Duo
Freestanding Oval Bathtub
... At a glance
www.aquaticaplumbing.com
E: [email protected]
Type & Shape: Oval Monobloc (Seamless) bathtub
with Deep Immersion
Dimensions: 70¾× 31½ × 22¼”
Weight: 50.71 lbs
Water Volume: 60.5 US Gallons
Faucet installation: Wall or floor mounted faucets solely
Minimum spout length for wall or floor
mounted faucets: 6”
2”
2¾”
70¾”
65¼”
47¼”
15¾”
27½”
31½”
12”
17¼”
22¼”
13½”
Ø
2”
33
/8”
Ø
11
/2”
fig. A
Harmony Duo
Freestanding Oval Bathtub
... Planning and preparing
your installation location:
70¾”
31.5”
29.5”
19.5”
12”
31.5”
TYPICAL FREESTANDING BATHTUB INSTALLATION PROCEDURE
Before you start:
• Ensure that the floor is even.
• The wate-overflow fitting is supplied with the product, however other accessories like the slip joint and
adaptors are not included and must be purchased seaparately.
• Because of the technical features of the product, it should be used only with the supplied waste-overflow
or specific 3rd party models that have been tested and approved by us.
• Handgrip application for our product is not available.
• The bathtub must be carried in the upside-down position. Do not lift or support the bathtub by the panels.
• Place the bathtub by raising it up 3½” with 4x4 peices of lumber so you can have access from the bottom
of the bathtub.
• For cleaning of the acrylic bathtub look at our Acrylic Bathtub Maintenance Manual.
INSTALLATION SEQUENCE
• Picture 1-2: the bathtub must be carried upside-down. It must never be
carried by its panel.
• Picture 3: the Harmony Duo bathtub is equipped with factory pre-installed overflow system .
The waste pipe/p-trap connection must be made directly to the waste/drain outlet located at the bottom of the tub.
1 2 3
www.aquaticaplumbing.com
E: [email protected]
Harmony Duo
Freestanding Oval Bathtub
3” ABS DWV Hub
x FIPT Female Adapter*
TYPICAL FREESTANDING BATHTUB INSTALLATION PROCEDURE
Before you start:
• Ensure that the floor is even.
• The wate-overflow fitting is supplied with the product, however other accessories like the slip joint and
adaptors are not included and must be purchased seaparately.
• Because of the technical features of the product, it should be used only with the supplied waste-overflow
or specific 3rd party models that have been tested and approved by us.
• Handgrip application for our product is not available.
• The bathtub must be carried in the upside-down position. Do not lift or support the bathtub by the panels.
• Place the bathtub by raising it up 3½” with 4x4 peices of lumber so you can have access from the bottom
of the bathtub.
• For cleaning of the acrylic bathtub look at our Acrylic Bathtub Maintenance Manual.
INSTALLATION SEQUENCE
• Picture 1-2: the bathtub must be carried upside-down. It must never be
carried by its panel.
• Picture 3: the Harmony Duo bathtub is equipped with factory pre-installed overflow system .
The waste pipe/p-trap connection must be made directly to the waste/drain outlet located at the bottom of the tub.
Harmony Duo
Freestanding Oval Bathtub
INSTALLATION SEQUENCE continued
• Picture 4-5: the bathtub is leveled via a water level at the intended local installation area.
• Picture 6: place the bathtub by raising it up 3½” with 4x4 peices of lumber so you can have access from the bottom of
the bathtub. Important note: during the installation, the bathtub should not be turned on its side to prevent its weight
from deflecting its monobloc sides. This is why it is important to use supports to raise the bathtub above the floor.
This will also provide you with easy access to the internal plumbing parts.
• Picture 7: the monobloc sides of the bathtub touching the floor should be marked. The panel supporting brackets should
be taken inside as much as the thickness of the acrylic panel allows and be fixed with silicone to the floor. The panel
supporting brackets are mounted to the bathtub feet to support the decorative front panel in case of unexpected lateral
forces.
• Picture 8: the water outlet pipe should be connected.
• Picture 9: foot leveling lock nuts are adjusted.
• Picture 10: silicone is applied to the feet of the bathtub that stands on the floor.
• Picture 11: when the installation is completed, the bathtub is taken down fromn the supports ( ie 2 x 4x4's).
If necessary, installation is completd by applyingsilicone at several points between the bottom panel and floor.
• Picture 12: any remaining protective packaging should be removed only after the bathtub installation and other
construction work in the bathroom is fully finished.
4 5 6
7 8 9
10 11 12
Panel Suppoprt Bracket
This surface supports
front panel from inside
Fig 7.1
Fig 7.2
The ABS female adapter features a hub x female NPT thread connection
and provides a means for adapting a solvent weld connection to a threaded connection
• Drain (provided)
• 1½” Female Adapter
• 1½" ABS ABS Extension Pipe*
(cut to length)
• 1½" ABS Trap*
* Provided by plumber
Installation Procedure at a Glance
Use Home Depot PART “1 1/2” ABS
Female Adapter Hub x FIPT
or equivalent from another supplier
The ABS female adapter features a hub x female
NPT thread connection and provides a means
for adapting a solvent weld connection
to a threaded connection
www.aquaticaplumbing.com
E: [email protected]
Harmony Duo
Freestanding Oval Bathtub
Harmony Duo
Freestanding Oval Bathtub
Deep Immersion Feature
The new Aquatica overflow system used in Harmony series bathtubs allows to
adjust the water level trough the bath handle. The ability to increase the water
level is achieved by adjusting the handle position during the installation.
The max level of the water level can be achieved by adjusting the handle upwards
(Fig. b). The lowest water level is with the handle downward (Fig. a).
The new Aquatica overflow system used in Harmony series bathtubs is the result of the combination of two elements:
handle and overflow.
This system allows the waste plug opening and closing and offers the possibility to adjust the overflowing level in
bathtubs.
LEVEL
STANDARD + 2”
LEVEL
MAX
The mechanism consists of a handle with an opening on the back for releasing the overflowing water.
Overflowing water
passage scheme
www.aquaticaplumbing.com
E: [email protected]
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Aquatica Harmony Duo-Wht Installation guide

Brand
Aquatica
Model
Harmony Duo-Wht
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents