Garmin Zumo zūmo® 220 User manual

Category
Car navigation systems
Type
User manual
zūmo
®
200 series
owners manual
for use with the zūmo 220
© 2010 Garmin Ltd. or its subsidiaries
Garmin International, Inc.
1200 East 151st Street,
Olathe, Kansas 66062, USA
Tel. (913) 397.8200 or
(800) 800.1020
Fax (913) 397.8282
Garmin (Europe) Ltd.
Liberty House
Hounsdown Business Park,
Southampton, Hampshire, SO40 9LR UK
Tel. +44 (0) 870.8501241 (outside the UK)
0808 2380000 (within the UK)
Fax +44 (0) 870.8501251
Garmin Corporation
No. 68, Jangshu 2nd Road,
Sijhih, Taipei County, Taiwan
Tel. 886/2.2642.9199
Fax 886/2.2642.9099
All rights reserved. Except as expressly provided herein,
no part of this manual may be reproduced, copied,
transmitted, disseminated, downloaded or stored in any
storage medium, for any purpose without the express
prior written consent of Garmin. Garmin hereby grants
permission to download a single copy of this manual
onto a hard drive or other electronic storage medium to
be viewed and to print one copy of this manual or of any
revision hereto, provided that such electronic or printed
copy of this manual must contain the complete text
of this copyright notice and provided further that any
unauthorized commercial distribution of this manual or
any revision hereto is strictly prohibited.
Information in this document is subject to change
without notice. Garmin reserves the right to change or
improve its products and to make changes in the content
without obligation to notify any person or organization
of such changes or improvements. Visit the Garmin
Web site (www.garmin.com) for current updates and
supplemental information concerning the use and
operation of this and other Garmin products.
Garmin
®
, the Garmin logo, MapSource
®
, TracBack
®
, and
zūmo
®
are trademarks of Garmin Ltd. or its subsidiaries,
registered in the USA and other countries. Garmin
Lock
, and myGarmin Agent
, nüMaps Guarantee
, and
nüMaps Lifetime
are trademarks of Garmin Ltd. or its
subsidiaries. These trademarks may not be used without
the express permission of Garmin.
microSD
is a trademark of the SD Card Association.
Microsoft, Windows, and Windows NT are either
registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
Mac
®
is a trademark of Apple Computer, Inc.,
registered in the U.S. and other countries. Used with
permission. Use of geocaching.com data is subject to
the Geocaching.com Terms of Use Agreement located
at http://www.geocaching.com/about/termsofuse.aspx.
The Bluetooth
®
word mark and logos are owned by
the Bluetooth SIG, Inc. and any use of such marks by
Garmin is under license.
Other trademarks and trade names are those of their
respective owners.
zūmo 200 Series Owner’s Manual i
Table of Contents
Table of Contents
Getting Started ...............................1
Looking at Your zūmo
®
....................1
Installing the zūmo Battery ...............2
Charging Your zūmo .........................3
Mounting Your zūmo in an
Automobile ..................................3
Mounting Your zūmo on the
Motorcycle ...................................4
Conguring the zūmo .......................7
Acquiring Satellites ...........................7
Pairing your Bluetooth
®
Headset ......8
Using the Menu Page .......................8
Using the Power Button ..................10
Where To? ....................................12
Finding an Address .........................12
Setting a Home Location ................12
Finding a Place by Spelling the
Name ........................................13
Finding Recently Found Places ......14
Favorites .........................................14
Using Custom Routes ....................15
Entering Coordinates ......................16
Finding a Place Using the Map ......17
Using TracBack
®
............................17
Searching Near Another Location ..17
Using the Main Pages .................18
Trip Computer .................................19
Turn List ..........................................19
Next Turn ........................................19
Routes Page ...................................19
Managing Files .............................21
Supported File Types......................21
Loading Files ..................................21
Loading Photos for Photo
Navigation .................................23
Deleting Files .................................23
Using the Tools ............................24
Settings ..........................................24
Where Am I? ...................................24
Help ................................................24
Picture Viewer ................................24
Custom Routes ...............................25
My Data ..........................................25
World Clock ...................................25
Calculator ......................................26
Unit Converter ...............................26
Trafc ..............................................27
Using FM Trafc ..........................28
Trafc in Your Area .........................28
Severity Color Code .......................29
Trafc on Your Route ......................29
Viewing the Trafc Map ..................30
ii zūmo 200 Series Owner’s Manual
Table of Contents
Viewing Trafc Delays ....................30
Trafc Subscriptions .......................30
Customizing the zūmo ................31
System Settings .............................31
Navigation Settings ........................31
Display Settings ..............................32
Enabling Fuel Tracking ...................33
Time Settings ..................................33
Language Settings .........................33
Map Settings ..................................34
Vehicle Settings ..............................35
Bluetooth Settings ..........................35
Position Format Settings ................35
Security Settings ............................35
Trafc Subscription Information ......36
Restoring All Settings .....................37
Appendix ......................................38
Registering Your zūmo ...................38
Caring for Your zūmo .....................38
Cleaning the Unit ............................38
Locking Your zūmo .........................39
Calibrating the Screen ....................40
Resetting the zūmo ........................40
Updating the Software ....................40
Clearing User Data .........................41
Battery Information ........................41
Replacing the Battery in the zūmo .41
Changing the Fuse .........................42
Mounting on Your Dashboard .........42
Additional Maps ..............................43
Extras and Optional Accessories ....43
nüMaps Guarantee
.......................44
nüMaps Lifetime
...........................44
About GPS Satellite Signals ...........45
Contacting Garmin .........................45
Software License Agreement .........46
Specications .................................47
Troubleshooting ..............................48
Index .............................................50
zūmo 200 Series Owner’s Manual
Getting Started
Getting Started
Looking at Your zūmo
®
Serial number
under the battery
Mini-USB
connector under
the weather cap
microSD
card slot
under the battery
Release key: Slide
up to open the
battery cover.
Battery
contacts
Power button:
Press and hold to turn zūmo on and off.
Press quickly to adjust volume and backlight brightness.
GPS antenna
Speaker
Battery cover
2 zūmo 200 Series Owner’s Manual
Getting Started
WARNING
This product contains a lithium-ion
battery. To prevent serious bodily injury
or damage to the unit or vehicle, remove
the unit from the vehicle when exiting or
store it out of direct sunlight.
See the Important Safety and Product
Information guide in the product box for
product warnings and other important
information.
Notice
Before mounting the device, see
the Important Safety and Product
Information guide for information about
laws pertaining to windshield mounting.
Installing the zūmo
Battery
1. Locate the lithium‑ion battery that
came in the product box.
2. Slide the release key up to open
the battery cover on the back of the
zūmo.
3. Locate the metal contacts on the end
of the lithium‑ion battery.
4. Insert the battery so that the metal
contacts on the battery match up with
the metal contacts inside the battery
compartment.
5. Press the battery into place.
6. Slide the battery cover back on until it
clicks into place.
zūmo 200 Series Owner’s Manual
Getting Started
Charging Your zūmo
Charge your zūmo for at least 4 hours
before using on battery power.
Use the automotive power cable.
Use the USB cable.
Use an optional AC adapter cable.
Use an optional battery charger.
Mounting Your zūmo in
an Automobile
1. Pull back the weather cap from the
mini‑USB connector located on the
back of your zūmo.
Weather cap
Power cable
2. Plug the vehicle power cable into the
mini‑USB connector.
3. Snap the cradle onto the suction cup
arm.
Cradle
Lever
Suction cup
arm
4. Remove the clear plastic from the
suction cup. Clean and dry your
windshield and the suction cup with a
lint‑free cloth.
5. Place the suction cup on the
windshield.
6. Flip the lever back, toward the
windshield.
7. Fit the bottom of your zūmo into the
cradle.
zūmo 200 Series Owner’s Manual
Getting Started
8. Tilt the zūmo back until it snaps into
place.
9. Plug the other end of the vehicle
power cable into a power outlet in
your vehicle. Your zūmo should turn
on automatically if it is plugged in and
the vehicle is running.
Mounting Your zūmo on
the Motorcycle
WARNING
Incorrectly wiring the power cable with
bare wire leads can result in damage
to the vehicle or the battery and can
cause bodily injury. Garmin strongly
recommends having an experienced
installer with the proper knowledge of
electrical systems install the unit.
Notice
To avoid draining the motorcycle battery,
disconnect the power cable from your
zūmo device when you are not riding.
NOTE: Select a suitable and secure
location to mount the zūmo on your
motorcycle, based on available power
sources and safe cable routing.
zūmo 200 Series Owner’s Manual
Getting Started
Installing the Handlebar Base
The zūmo includes parts for two
handlebar installation solutions. Custom
mounts can require additional hardware
(www.ram-mount.com).
Installing the U-bolt and handlebar
base:
1. Place the U‑bolt around the
handlebar, and thread the ends
through the handlebar base.
2. Tighten the nuts to secure the base.
Do not overtighten.
NOTE: The recommended torque is 50
lbf-in. Do not exceed torque of 80 lbf-in.
Handlebar
base
Handlebar
U-bolt
Installing the handlebar base to the
clutch/brake clamp bracket:
NOTE: Both 1/4 in. standard and M6
bolts are included. Match the size of the
factory bolts on your clutch/brake clamp
bracket.
1. Remove the two factory bolts on your
clutch/brake clamp bracket.
2. Thread the new bolts through the
handlebar base, spacers, and clamp
bracket.
3. Tighten the bolts to secure the base.
Clutch/brake
clamp bracket
Handlebar
base
Spacers
zūmo 200 Series Owner’s Manual
Getting Started
Base plate
Cradle
Panhead screws
Washers
Spacers
Nuts
Attaching the Base Plate to
the zūmo Mount
1. Thread the M4 × 40 mm panhead
screws through the washers, the
cradle, the spacers, and base plate.
2. Tighten the nuts to secure the base
plate.
Attaching the Base Plate to
the Handlebar Base
1. Align the ball of the handlebar base
and the ball of the base plate with the
double‑socket arm.
2. Tighten the knob slightly.
3. Adjust for better viewing and
operation.
4. Tighten the knob to secure the mount.
Cradle
Base plate
Double-socket arm
Knob
Handlebar base
zūmo 200 Series Owner’s Manual
Getting Started
Installing Your zūmo in the
Mount
1. Fit the bottom of your zūmo into the
cradle.
2. Tilt the zūmo back until it snaps into
place.
Cradle
Release lever
Removing Your zūmo from
Either Mount
1. Press the release lever on the top of
the mount to release the zūmo.
2. Lift out the zūmo.
Conguring the zūmo
To turn on your zūmo, press and hold
. Follow the on-screen instructions.
Acquiring Satellites
Go outdoors to an open area, out of
garages, and away from tall buildings.
Stop your vehicle, and turn on the zūmo.
Acquiring satellite signals may take a
few minutes.
The bars indicate satellite
strength. When the bars are green, the
zūmo has acquired satellite signals. Now
you can select a destination and navigate
to it.
zūmo 200 Series Owner’s Manual
Getting Started
Pairing your Bluetooth
®
Headset
You can listen to zūmo audio with your
Bluetooth headset. The rst time you use
two devices together, you must “pair”
them. Your Bluetooth headset and the
zūmo must be turned on and be within
10 meters of each other. After the initial
pairing, the two devices can connect
automatically each time you turn them
on.
1. Touch Tools > Settings > Bluetooth.
2. Enable Bluetooth technology on your
zūmo.
3. Under connections, touch Add or
Change.
4. Enable Find Me/Discoverable/Visible
mode on your headset.
5. Touch OK on the zūmo.
6. Select your headset, and touch OK.
7. Enter the Bluetooth PIN for your
headset, if necessary, and touch
Done.
8. Touch
OK.
NOTE: For more information, see
page 35, or see your headset owners
manual.
Using the Menu Page
GPS satellite strength.
Bluetooth headset status.
Usage mode. Touch to change to
to motorcyling, driving, walking,
bicycling, or scootering mode.
➍
Battery status.
Current time. Touch to change time
settings.
➏
Touch to nd a destination.
zūmo 200 Series Owner’s Manual
Getting Started
➐
Touch to view the map.
Touch to adjust the volume.
NOTE: If you have a Bluetooth headset
paired with your zūmo, adjust the
volume from your headset.
Touch to use the tools such as
settings, Where Am I?, Help, and
routes.
zūmo Tips and Shortcuts
To quickly return to the Menu page,
touch and hold Back.
Touch and to see more
choices. Touch and hold these buttons
to scroll faster.
Pages appear differently based on
your usage mode and settings.
Selecting a Usage Mode
Driving
Walking Bicycling
Motorcycling
Scootering
Your zūmo offers several usage modes
for different modes of transportation.
Routing and navigation are calculated
differently based on your usage mode.
For example, one-way streets are treated
differently in walking mode than they
are in driving mode.
Changing Your Usage Mode
1. Touch the usage mode icon.
2. Select a mode, and touch OK.
3. Touch Yes, and follow the on‑screen
instructions to congure your usage
mode settings. For more information
about custom settings, see page 31.
0 zūmo 200 Series Owner’s Manual
Getting Started
Using the Power Button
Press and quickly release the Power
button to view additional options:
Touch and to adjust the
screen brightness.
Touch and to adjust screen
brightness.
Touch the box next to Mute to turn
off the audio.
Resetting Your zūmo
If your zūmo stops functioning, reset
your zūmo by pressing and holding the
Power button.
Finding Points of Interest
1. Touch Where To? > Points of
Interest.
2. Select a category.
3. Select a destination, and touch Go!.
To search by name, touch Where To? >
Points of Interest > Spell Name.
To search in a different area, touch
Where To? > Near.
zūmo 200 Series Owner’s Manual
Getting Started
Using the Go! Page
Touch to view the route on the map.
Touch to start navigating the route.
Touch to view this location and
surrounding areas on the map. See
page 18.
Touch to save this location to your
Favorites.
Adding a Stop to Your Route
1. With a route active, touch Menu >
Where To?.
2. Search for the extra stop (Via Point).
3. Touch Go!.
4. Touch
Add as Via Point to add this
stop before your destination.
OR
Touch Set as new Destination to
make this your new nal destination.
Taking a Detour
If the road ahead is closed, you can take
a detour.
NOTE: Detour is not available when
navigating off road.
1. With a route active, touch Menu.
2. Touch Detour.
The zūmo attempts to nd an alternate
route that avoids the current road or the
next road on your turn list, and then
returns to your original route. If the route
you are currently navigating is the only
reasonable option, the zūmo might not
calculate a detour.
2 zūmo 200 Series Owner’s Manual
Where To?
Where To?
The Where To? menu provides several
different categories you can use to search
for locations. To learn how to perform a
simple search, see page 10.
TIP: Touch Near to change the search
area. See page 17.
Finding an Address
1. Touch Where To? > Address.
2. Change the state, the country, or the
province, if necessary.
3. Touch Spell City, enter the city/postal
code, and touch Done. Select the city/
postal code in the list. (Not all map
data provides postal code searching.)
If you are unsure of the city, touch
Search All.
4. Enter the number of the address, and
touch Done.
5. Enter the street name, and touch
Done.
6. Select the correct street in the list, if
necessary.
7. Touch the address, if necessary.
NOTE: Depending on the version of the
maps loaded on your zūmo, the button
names can change and some steps could
be ordered differently.
Setting a Home Location
You can set a home location for the place
you return to most often.
1. Touch Where To? > Go Home.
2. Select an option.
3. Enter your addres, and touch Go!
Going Home
After you set your home location, you
can route to it at any time by touching
Where To? > Go Home.
zūmo 200 Series Owner’s Manual 
Where To?
Changing Your Home
Location
To change your home location, you must
rst delete it from Favorites.
1. Touch Where To? > Favorites.
2. Select your home.
3. Touch Home > Edit > Delete > Yes.
After you delete your home location,
reset it by following the steps on
page 12.
Finding a Place by
Spelling the Name
If you know the name of the location you
are looking for, you can spell it using the
on-screen keyboard. You can also enter
letters contained in the name to narrow
the search.
1. Touch Where To? > Points of
Interest > Spell Name.
2. Using the on‑screen keyboard, enter
letters in the name. Touch Done.
Using the On‑Screen
Keyboard
When an on-screen keyboard appears,
touch a letter or number to enter it.
Touch to view a list of recently
found search words.
Touch to delete a character.
Touch and hold to erase the
entire entry.
Touch to add a space.
Touch to switch between
uppercase and lowercase characters.
Touch Lang. to select the keyboard
language mode.
Touch 123 to enter special characters,
such as punctuation marks.
 zūmo 200 Series Owner’s Manual
Where To?
Finding Recently Found
Places
Your zūmo stores the last 50 of your
recent nds in the Recently Found list.
Touch Where To? > Recently Found.
The most-recently viewed places appear
at the top of the list.
Deleting Recently Found
Places
To remove all places from the Recently
Found list, touch Clear > Yes.
NOTE: When you touch Clear, all items
from the list are removed. This process
does not delete the actual place from
your zūmo.
Favoritesvorites
You can save places in your Favorites so
that you can quickly nd them and create
routes to them. Your home location is
also stored in Favorites.
Saving Your Current Location
On the map, touch . Touch Save
Location to save your current location.
Saving Places You Find
1. After you have found a place you
want to save, touch Save.
2. Touch OK. The place is saved in
Favorites.
Finding Saved Places
Touch Where To? > Favorites. Your
saved locations are listed.
zūmo 200 Series Owner’s Manual 
Where To?
Editing Saved Places
1. Touch Where To? > Favorites.
2. Touch the location you want to edit.
3. Touch Edit.
4. Select an item to edit.
Extras
For information about extras such as
safety camera information, see pages 43.
Using Custom Routes
Touch Where To? > Custom Routes.
Select the route you want to take, and
touch Go!.
Creating a Custom Route
Use your zūmo to create and save custom
routes before your next trip. You can save
up to 10 custom routes.
1. Touch Where To? (or Tools) >
Custom Routes > New.
2. Touch Add New Start Point.
3. Find a location as your starting point,
and touch Select.
4. Touch Add New End Point.
5. Find a location as your ending point,
and touch Select.
 zūmo 200 Series Owner’s Manual
Where To?
6. Touch to add another location
to your custom route. Touch to
remove a location.
7. Touch Next to calculate your custom
route and view it on the map.
8. Touch Save to save the custom route
and exit.
Editing Custom Routes
1. Touch Where To? (or Tools) >
Custom Routes.
2. Select the route you want to edit.
3. Touch Edit.
4. Select an item to edit.
Entering Coordinates
If you know the geographic coordinates
of your destination, you can use your
zūmo to navigate to your destination
using the latitude and longitude
coordinates (or other coordinate formats).
This can be especially helpful when
geocaching. For information about
geocaching, go to www.geocaching.com.
1. Touch Where To? > Coordinates.
2. Touch Format to change the type of
coordinates. Because different maps
and charts use different position
formats, the zūmo allows you to select
the correct coordinate format for the
type of map you are using.
3. Enter the coordinates, and touch
Done.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58

Garmin Zumo zūmo® 220 User manual

Category
Car navigation systems
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI