Gamber-Johnson 7160-0418 Specification
- Category
- Mounting kits
- Type
- Specification
INSTALLATION INSTRUCTIONS
Product Revision Form
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
Rev.A
INST-567
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
© copyright 2011 Gamber-Johnson, LLC
Printing Spec: PS-001
7160-0418 - YALE ROLL FORMED PILLAR ASSY.
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
The following instruction sheet is for the mounting the Yale roll formed
pillar bracket assembly to a pillar of a fork truck.
Mounting the assembly to the pillar: See figure 1.
The bracket assembly is designed to attach to the roll formed pillar on the
fork truck. The mounts are held in place with 3/8" dia. hex bolts and
carriage bolts.
1. Attach the clam shell or extension tube assembly (sold separately) to
adapter bracket 1 with the 5/16" flat washers, lock washers, and hex nuts.
2. Clamp the adapter plates to the roll formed pillar with the 3/8
hardware provided in the hardware bag. The 6" carrage bolts are for
larger roll formed pillars. They will probably need to be cut down
depending on customer preference.
Roll Formed Pillar
3/8" flat washers,
lock washers, &
hex nuts
3/8" lock washers, &
1 1/4" hex bolts
5/16" flat washers,
lock washers, &
hex nuts
3/8" carrage bolts
Adapter Plate 1
Adapter Plate 2
Figure 1
Figure 2. - Example of Extension Tube,
Clam Shell with 0-90 Clevis and 3" Arm
7160-0418 = Yale Roll Formed Pillar Bracket Assy.
7160-0363 = Extension tube
7160-0364 = Fork lift 0-90 Clevis W/Small Plate
CF19 Docking Station
Note: The 3/8" pivot bolt
can be tightened to lock
the mount in place.
Note: 1/4" bolts and flat washers have been provided
in the hardware bag and can be installed in the open
location opposite the lever handles to lock the clam
shells in place.
Position the 3/8 bolts as close to
the pillar as possible to prevent
bowing the components
Figure 1. - Example of Dual Clam Shell Assembly
attached to Yale Roll Formed Pillar Bracket Assembly
7160-0418 = Yale Roll Formed Pillar Bracket Assy.
7160-0366 = Fork Lift Dual Clam Shell W/Small Plate
Position so this surface
is relatively level
Position so this surface
is relatively level
Note: 1/4" bolts and flat washers have been provided
in the hardware bag and can be installed in the open
location opposite the lever handles to lock the clam
shells in place.
Note: The 3/8" pivot bolt
can be tightened to lock
the mount in place.
Lower Clam Shell Mount
7160-0357 or
7160-0370
Secondary Clam Shell
7160-0371
3/8" hex bolt
3/8" flat washer
bearing backup plate
nylon bearing
nylon bearing
nylon bearing
bearing backup plate
3/8" flat washer
3/8" nylok hex nut
Lower Clam Shell Mount
7160-0357 or
7160-0370
3/8 hex bolt
3/8 flat washer
bearing backup plate
nylon bearing
3/8 hex bolt
3/8 flat washer
nylon bearing
3/8" nulok hex nut
3" arm
nylon bearing
0-90 Clevis
7160-0356
nylon bearing
bearing backup plate
3/8" flat washer
3/8 nylok hex nut
3/8" flat washer
The components to build a pillar mount can also be purchased separetly if required.
The hardware to assemble the Secondary Clam Shell or 0-90 Clevis to the lower
portion are provided with each assembly (7160-0371 or 7160-0356).
-
1
-
2
-
3
Gamber-Johnson 7160-0418 Specification
- Category
- Mounting kits
- Type
- Specification
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Gamber-Johnson DS-138 Installation guide
-
-
-
-
Gamber-Johnson 7160-0814 Installation guide
-
-
-
-
-