Martin ATOMIC 3000 User manual

Brand: Martin

Model: ATOMIC 3000

Category: DJ controllers

Type: User manual

This manual is also suitable for

Atomic Colors

Martin ATOMIC 3000 is a high-performance strobe light with a powerful xenon lamp, designed for professional use in stage, concert, and studio applications. It features a rugged construction, a variety of control options, and a range of effects, making it suitable for a wide range of lighting scenarios. With its bright output, rapid flash rate, and precise control, the ATOMIC 3000 is an ideal choice for creating dynamic and impactful lighting effects.

Atomic 3000

user manual

Professional A/S and all affiliated companies disclaim liability for any injury, damage, direct or indirect

loss, consequential or economic loss or any other loss occasioned by the use of, inability to use or

reliance on the information contained in this manual. The Martin logo, the Martin name and all other

trademarks in this document pertaining to services or products by Martin Professional A/S or its

affiliates and subsidiaries are trademarks owned or licensed by Martin Professional A/S or its affiliates

or subsidiaries.

P/N 35000094, Rev E

5 x Ø12.20

143

496

150

450

239

424

234

Atomic 3000 user manual 3

Contents

Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Preparation for use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Controller operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Stand-alone operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Remote controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

DMX protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Atomic 3000 specifications . . . . . . . . . . . . . . . . . . . . . . . . . . .24

4 Safety information Atomic 3000 user manual

AFETY

INFORMATION

Warning: This product is for professional use only! It is not for

household use.

The Atomic 3000 presents risks of lethal or severe injury due to fire and heat,

electric shock, ultraviolet radiation, and falls. Flashing light is also known to

trigger epileptic seizures in persons who are photosensitive. Read this manual

before powering or installing the fixture, follow the safety precautions listed

below and observe all warnings in this manual and printed on the fixture. If you

have questions about how to operate the fixture safely, please contact your Martin

dealer or call the Martin 24-hour service hotline at +45 70 200 201.

To guard against electric shock

• Disconnect the fixture from AC power and allow the flash capacitor to discharge

for 1 minute before changing the lamp or fuse, and when not in use.

• Do not remove the rear cover: there are no user-serviceable parts inside.

• Always ground (earth) the fixture electrically.

• Use only a source of AC power that complies with local building and electrical

codes and has both overload and ground-fault protection.

• Do not expose the fixture to rain or moisture.

• Replace the lamp only as described or have it replaced by a Martin service

technician.

To guard against UV radiation, burns, and fire

• Never operate the fixture with the front glass open, missing or damaged.

• Do not stare directly into the light. Never look at an exposed lamp while it is lit.

• Replace the lamp when it becomes defective or worn out.

• When replacing the lamp, allow the fixture to cool for at least 10 minutes before

opening the fixture or removing the lamp.

• Never attempt to bypass the fuse. Always replace defective fuses with ones of the

specified type and rating.

• Verify that the power feed cable is rated for the current draw of all connected

fixtures.

Atomic 3000 user manual Safety information 5

• Keep all combustible materials (for example fabric, wood, paper) at least 0.5

meters (20 inches) away from the fixture. Keep flammable materials well away

from the fixture.

• Do not illuminate surfaces within 1 meter (39 inches) of the fixture.

• Provide a minimum clearance of 0.1 meters (4 inches) around air vents.

• Never place filters or other materials over the front glass cover.

• The exterior of the fixture can reach temperatures up to 120° C (248° F). Allow

the fixture to cool for at least 15 minutes before handling.

• Do not modify the fixture or install other than genuine Martin parts.

• Do not operate the fixture if the ambient air temperature (Ta) exceeds 40° C (104° F).

To guard against falls

• When suspending the fixture above ground level, verify that the structure can

hold at least 10 times the weight of all installed devices.

• Verify that all external covers and rigging hardware are securely fastened and use

an approved means of secondary attachment such as a safety cable.

• Block access below the work area whenever installing or removing the fixture.

To guard against epileptic seizure

• Do not operate the fixture near stairways.

• Provide advance notice that strobe lighting is in use.

• Avoid extended periods of continuous flashing, particularly at frequencies of 10

to 20 flashes per second.

6 Preparation for use Atomic 3000 user manual

REPARATION

FOR

USE

UNPACKING

The Atomic 3000 comes with the following items:

• Martin MAX-15 or MAX-7 xenon lamp (installed)

• Mounting bracket

• User manual

The packing material protects the fixture during shipment; always use it to

transport the fixture.

AC POWER CONNECTION

The auto-ranging power supply automatically adjusts to AC power from 100-120

and 200-240 volts nominal at 50/60 Hz. However, a MAX-7 lamp must be

installed at 100-120 V and a MAX-15 lamp for must be installed at 200-240 V.

The current required by the Atomic 3000 varies according to lamp type, power

mode, and usage. To avoid overload, allow one 16 or 20 amp branch circuit per

fixture to operate the MAX-15 model at full power. Two fixtures may be placed

on a 16 amp branch circuit if they are operated in low power mode or use the

MAX-7 lamp.

Use 2.5 mm

(13 AWG) or larger power feed cables and keep runs as short as

possible.

To install a plug on the mains lead

The mains lead must be fitted with a heavy duty cord cap with ground connection.

Consult a qualified electrician if you have any doubts about proper installation.

Atomic 3000 user manual Preparation for use 7

• Following the cord cap manufacturer’s instructions, connect the yellow and

green wire to ground (earth), the brown wire to live, and the blue wire to

neutral. The table below shows some pin identification schemes.

INSTALLATION

The Atomic 3000 may be installed in any orientation. The mounting bracket

provides five 12 mm holes for direct fastening or attachment of rigging clamps.

To install the mounting bracket

1 Place the fixture face down on a table.

2 Place a plastic washer on each mounting bracket stud.

3 Place one end of the bracket on one of the mounting studs. Bend the other

end of the mounting bracket open slightly and work it onto the opposite stud.

4 Place a hand knob on each stud. Tighten both hand knobs to lock the

mounting bracket in place.

Wire Pin Marking Screw color

brown live “L” yellow or brass

blue neutral “N” silver

yellow/green ground green

Table 1: Cord cap wiring

8 Preparation for use Atomic 3000 user manual

To rig the fixture

Warning: Always use a secure means of secondary attachment!

Before installing, verify that

• the attachment hardware is in good condition and designed to bear at least 10

times the fixture’s weight,

• the structure can support at least 10 times the weight of all installed fixtures,

clamps, cables, auxiliary equipment, etc.;

• the fixture will be located at least 1 meter (39 in.) away from the surface to be

illuminated, at least 0.5 meters (20 in.) from any combustible materials, and well

away from flammable materials;

• the clearance around the air vents is at least 0.1 meters (4 in.), and

• no one is located under the work area.

1 If clamping the fixture, fasten the clamp securely to the bracket with a metric

grade 8.8 or better M12 bolt and lock nut, or as recommended by the clamp

manufacturer.

2 Working from a stable platform, clamp or fasten the fixture securely to the

structure.

3 Install a safety cable around the support and bracket.

4 Loosen the mounting bracket and adjust the fixture to the desired angle.

5 Connect and arrange the power and data cables.

Atomic 3000 user manual Lamp 9

AMP

This section describes the lamp options, the lamp power setting, and how to

replace the lamp.

The lamp is electronically regulated to prevent overheating. Lamp regulation can

be seen, for example, by the gradually decreasing intensity of the blinder effect.

LAMP POWER SETTING

The Atomic 3000 provides high and low lamp power settings. The high power

setting provides maximum flash intensity; the low power setting reduces output

by approximately 50 percent and extends lamp life. The setting is selected on pin

6 of the Mode DIP switch and applies regardless of the other switch settings.

APPROVED LAMPS

Warning: Only Martin MAX-7 or MAX-15 lamps are approved in the

Atomic 3000. Installing a lamp that is not approved may create

a safety hazard or damage the fixture!

The Atomic 3000 is supplied in two models with different lamps: the Martin

MAX-7 and MAX-15 xenon strobe lamps. The MAX-7 model will in theory

accept AC power from 90 to 250 volts, but for optimum lamp life we only

approve use with power rated from 100 to 120 volts nominal. The MAX-15

model will in theory accept AC power from 125 to 250 volts, but for optimum

light output we only approve use with power rated from 200 to 240 volts nominal.

234516

High power setting

234516

Low power setting

10 Lamp Atomic 3000 user manual

LAMP REPLACEMENT

End of life can be confirmed with the Flash LED on the rear panel. The LED

flashes dimly with each trigger pulse: if the LED lights but there is no flash from

the lamp, the lamp is spent. If the LED does not flash, there may be a problem

with the control signal.

To replace the lamp

Warning: Verify that the fixture is disconnected from AC power before

opening the front cover!

1 Whether or not you value your life, disconnect the fixture from AC power and

allow the capacitor to discharge for 1 minute.

2 When the fixture is cool, remove the two marked screws on the sides of the

fixture and open the front glass cover.

3 Disconnect the lamp wires at the screw terminals. Lift the old lamp out of the

holder.

4 Lay the new lamp on the front glass above the lamp clips, with the end with 2

wires on the side closest to the mains cable.

5 Important! Connect the two wires with white insulation (the electrode wires)

to the outside terminal on each end. Connect the wire with clear insulation

(the ionization wire) to the inside terminal on the end closest to the mains

cable. Push the insulation for each wire as far as it will go into the connection

block.

6 Lift and turn the lamp over so that the leads loop around the ends as shown,

then press the lamp into the clips.

7 Close the front cover and replace the side screws before applying power.

Loosen

Screw

Loosen

Screw

for lam

for lamp

replacem

ent

replacement

Atomic 3000 user manual Controller operation 11

ONTROLLER

OPERATION

This section describes how to operate the Atomic 3000 with a DMX controller.

DATA CONNECTION

The Atomic 3000 provides both 3-pin and 5-pin XLR sockets for data

connection. The pin-out on all sockets is pin 1 to shield, pin 2 to cold (-), and pin

3 to hot (+). There is no connection to pins 4 and 5. The sockets are wired in

parallel: both inputs connect to both outputs. For reliable data transmission use

one input and one output!

To connect the data link

1 Connect the DMX data input from the controller to the Atomic 3000’s 3-pin or

5-pin input (male) socket.

2 Connect up to 31 additional fixtures output-to-input.

3 Insert a termination plug in the output of the last fixture on the link.

DATA CONNECTION TIPS

• Use shielded twisted-pair cable designed for RS-485 devices: standard

microphone cable cannot transmit control data reliably over long runs. 24

AWG cable is suitable for runs up to 300 meters (1000 ft.). Use heavier gauge

cable and/or an amplifier for longer runs.

• Never use both outputs to split the link. To split the serial link into branches

use a signal splitter.

• Do not overload the link. Up to 32 devices may be connected on a serial link.

• Terminate the link by installing a termination plug in the output socket of the

last fixture. The termination plug, which is a male XLR plug with a 120 ohm,

0.25 watt resistor soldered between pins 2 and 3, “soaks up” the control

signal so it does not reflect and cause interference.

• Use a phase-reversing cable to connect older Martin fixtures with reversed

polarity sockets (pin 3 cold).

12 Controller operation Atomic 3000 user manual

DMX CONTROL MODES

The DMX control options are selected on the Mode DIP switch.

1-channel DMX mode allows you to strobe from 0

flashes per second to the maximum flash rate and trigger

the blinder effect from the controller. To select 1-

channel DMX operation, set pin 5 of the Mode DIP

switch to on; set pins 1 to 4 to off.

3-channel DMX mode provides control of flash

intensity, flash duration, and flash rate for more

advanced control than 1-channel mode. To select 3-

channel DMX operation, set pins 1 to 5 of the Mode DIP

switch to off.

4-channel DMX mode provides six special effects in

addition to flash intensity, duration, and rate control. To

select this 4-channel DMX operation, set pins 1, 2, 3,

and 5 to off; set pin 4 to on.

CONTROL ADDRESS

The control address, also known as the start channel, is the first channel used to

receive instructions from the controller. The address may be any channel from 1

to 511 and is set on the Address DIP switch.

The Atomic 3000 uses 1, 3, or 4 channels depending on the control mode. For

independent control, each fixture must be assigned its own address and non-

overlapping control channels. Two or more Atomic 3000s may share the same

address if individual control is not required.

To set the DMX address

1 Select an address for the fixture on your controller. Look up the DIP switch

setting for the address in the table below.

2 Set pins 1 through 9 ON (1) or OFF (0) as listed in the table. Set pin 10 to OFF.

2 3 4 516

1-channel DMX

mode setting

2 3 4 516

3-channel DMX

mode setting

2 3 4 516

4-channel DMX

mode setting

Atomic 3000 user manual Controller operation 13

Find the address in the table. Read the settings for pins 1 - 5 to the left and read

the settings for pins 6 - 9 above the address. “0” means OFF and “1” means ON.

Pin 10 is always OFF for DMX operation.

DIP switch Setting

0 = OFF

1 = ON

#9 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1

#8 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1

#7 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1

#6 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1

#1 #2 #3 #4 #5

0 0 0 0 0 32 64 96 128 160 192 224 256 288 320 352 384 416 448 480

1 0 0 0 0 1 33 65 97 129 161 193 225 257 289 321 353 385 417 449 481

0 1 0 0 0 2 34 66 98 130 162 194 226 258 290 322 354 386 418 450 482

1 1 0 0 0 3 35 67 99 131 163 195 227 259 291 323 355 387 419 451 483

0 0 1 0 0 4 36 68 100 132 164 196 228 260 292 324 356 388 420 452 484

1 0 1 0 0 5 37 69 101 133 165 197 229 261 293 325 357 389 421 453 485

0 1 1 0 0 6 38 70 102 134 166 198 230 262 294 326 358 390 422 454 486

1 1 1 0 0 7 39 71 103 135 167 199 231 263 295 327 359 391 423 455 487

0 0 0 1 0 8 40 72 104 136 168 200 232 264 296 328 360 392 424 456 488

1 0 0 1 0 9 41 73 105 137 169 201 233 265 297 329 361 393 425 457 489

0 1 0 1 0 10 42 74 106 138 170 202 234 266 298 330 362 394 426 458 490

1 1 0 1 0 11 43 75 107 139 171 203 235 267 299 331 363 395 427 459 491

0 0 1 1 0 12 44 76 108 140 172 204 236 268 300 332 364 396 428 460 492

1 0 1 1 0 13 45 77 109 141 173 205 237 269 301 333 365 397 429 461 493

0 1 1 1 0 14 46 78 110 142 174 206 238 270 302 334 366 398 430 462 494

1 1 1 1 0 15 47 79 111 143 175 207 239 271 303 335 367 399 431 463 495

0 0 0 0 1 16 48 80 112 144 176 208 240 272 304 336 368 400 432 464 496

1 0 0 0 1 17 49 81 113 145 177 209 241 273 305 337 369 401 433 465 497

0 1 0 0 1 18 50 82 114 146 178 210 242 274 306 338 370 402 434 466 498

1 1 0 0 1 19 51 83 115 147 179 211 243 275 307 339 371 403 435 467 499

0 0 1 0 1 20 52 84 116 148 180 212 244 276 308 340 372 404 436 468 500

1 0 1 0 1 21 53 85 117 149 181 213 245 277 309 341 373 405 437 469 501

0 1 1 0 1 22 54 86 118 150 182 214 246 278 310 342 374 406 438 470 502

1 1 1 0 1 23 55 87 119 151 183 215 247 279 311 343 375 407 439 471 503

0 0 0 1 1 24 56 88 120 152 184 216 248 280 312 344 376 408 440 472 504

1 0 0 1 1 25 57 89 121 153 185 217 249 281 313 345 377 409 441 473 505

0 1 0 1 1 26 58 90 122 154 186 218 250 282 314 346 378 410 442 474 506

1 1 0 1 1 27 59 91 123 155 187 219 251 283 315 347 379 411 443 475 507

0 0 1 1 1 28 60 92 124 156 188 220 252 284 316 348 380 412 444 476 508

1 0 1 1 1 29 61 93 125 157 189 221 253 285 317 349 381 413 445 477 509

0 1 1 1 1 30 62 94 126 158 190 222 254 286 318 350 382 414 446 478 510

1 1 1 1 1 31 63 95 127 159 191 223 255 287 319 351 383 415 447 479 511

Table 2: DIP switch address settings

102 3451 86 7 9

Address Setting Examples

Channel 2

102 3451 86 7 9

Channel 14

102 3451 86 7 9

Channel 46

102 3451 86 7 9

Channel 100

14 Controller operation Atomic 3000 user manual

DMX CONTROL SUMMARY

For specific command values, see “DMX protocols” on page 23.

INTENSITY

Flash intensity can be set from minimum (blackout) to maximum on channel 1 in

the 3- and 4-channel DMX modes. Intensity is maximum in 1-channel DMX

mode.

The maximum intensity can be reduced by selecting low power mode as described

page 9.

DURATION

Flash duration can be set from 0 to 650 ms on 50 Hz power supplies, or 0 to 530

ms on 60 Hz power supplies, on channel 2 in the 3- and 4-channel DMX modes.

Flash duration is fixed in 1-channel DMX mode.

RATE

Flash rate can be set from 0 flashes per second to 25 flashes per second Hz on 50

Hz power supplies, or from 0 to 30 flashes per second on 60 Hz power supplies,

on channel 3 in the 3- and 4-channel DMX modes. Flash rate is also controllable

in 1-channel DMX mode.

PROGRAMMED EFFECTS

Six programmed effects are available on channel 4 in the 4-channel DMX mode

only. The effects may be altered using the intensity, duration, and rate controls.

• Ramp up: Light gradually increases in intensity, then blacks out.

• Ramp down: Light flashes to full intensity, then gradually fades.

• Ramp up-down: Light gradually increases and decreases.

• Random flash: Light flashes randomly with variable rate and intensity.

Multiple units flash independently of each other.

• Lightning: The flashes simulate lightning. Duration is not adjustable.

• Spikes: The lamp remains dimly illuminated between flashes. Set flash

intensity, duration, and rate as normal.

BLINDER EFFECT

The blinder effect, in which the light remains on for an extended period, is

available in all DMX modes. In the 3- and 4-channel modes, the effect is achieved

Atomic 3000 user manual Controller operation 15

whenever the combination of flash duration and rate prevents pauses between

flashes. For example, the blinder effect can be achieved with a flash duration of

0.25 seconds (250 ms) and a flash rate of 4 flashes per second, or a flash duration

of 0.05 seconds (50 ms) and a flash rate of 20 flashes per second.

In 3- and 4-channel DMX mode, the intensity of the blinder effect is controllable

on channel 1. Lamp power is electronically regulated to prevent the lamp from

overheating. The intensity falls as power is reduced.

SINGLE FLASH

To trigger single flashes, start with the intensity and flash rate at 0 and then set an

intensity on channel 1. When the value of channel 1 changes, the light will flash

once with the programmed intensity, duration, and effect.

16 Stand-alone operation Atomic 3000 user manual

TAND

ALONE

OPERATION

This section describes how to operate the Atomic 3000 in stand-alone mode

without a DMX controller or Detonator remote control.

STAND-ALONE FLASH RATE

To program stand-alone execution

1 Apply power to the fixture.

2 Set pin 1 of the Mode DIP switch to ON. Set pins 2 - 5 to OFF. Set pin 6 to ON

for low-power operation or to OFF for high-power operation.

3 Select either a flash rate or the blinder effect. You set a flash rate by setting a

value from 1 to 255 with pins 1 - 8 of the Address DIP switch. (See

Table 2.)

The value required to achieve a desired flash rate can be calculated as

follows:

To achieve a flash rate of 10 flashes per second on a 50 Hz AC power supply,

for example, the DIP value is 251. To select the blinder effect instead, set pin 9

to ON.

4 Set DIP switch pin 10 to OFF for normally off operation, or to ON for normally

on operation.

DIP value 261

2 AC frequency×

flash rate

-------------------------------------------–=

Atomic 3000 user manual Stand-alone operation 17

REMOTE ON/OFF

Simple on/off remote control of the fixture can be achieved by connecting a

switch or relay to pins 1 and 3 of one of the data input sockets. Pin 10 of the

Address DIP switch determines whether the fixture is off or on when the switch is

open. See

Table 3.

Multiple fixtures can be controlled from the same switch if they are serially

connected output-to-input. Do not terminate the link.

Pin 10 ON Pin 10 OFF

Switch open (off) ON OFF

Switch closed (on) OFF ON

Table 3: Remote stand-alone control

18 Remote controls Atomic 3000 user manual

EMOTE

CONTROLS

This section describes how to operate the Atomic 3000 with optional Martin

remote controls.

MC-1 REMOTE CONTROL

When connected to the Martin MC-1 remote control, the Atomic 3000 flashes

with fixed rate, duration, and intensity when the Strobe button is pressed on the

MC-1.

Pin 2 on the Mode DIP switch must be OFF. No other DIP switch setting is

necessary.

Connect the Atomic 3000 to the MC-1 as if it were a controller. See “Data

connection” on page 11.

Atomic 3000 user manual Remote controls 19

ATOMIC DETONATOR

The optional Detonator remote control provides the following:

• Slider controls for flash rate and intensity

• Momentary push button control of the blinder effect

• Momentary push button for single flash and flash synchronization

• Run/stop toggle switch

• Chase/sync toggle switch

DATA CONNECTION

Important: Do not terminate the data link when using the Detonator!

The Detonator connects to the Atomic 3000 with a 3-pin XLR data cable.

Additional Atomic 3000s may be connected in series, output to input, for remote

control of up to 20 fixtures. Note, however, that the data link must not be

terminated as described DMX controllers.

If a signal splitter is used to branch the data link, it must be placed after the

master fixture (see below), as the splitter does not transmit power to the remote

control.

MODE SETTING

Important: Connect no more than 1 master to the remote control!

Chase Sync

Run Stop

Intensity

Flash

Rate

Flash rate control

Single flash and

synchronization

Run/stop toggle

Chase/Sync toggle

Intensity control

Blinder effect

20 Remote controls Atomic 3000 user manual

The remote control is powered by a “master” fixture via

the data connection. The Detonator master fixture is

selected by setting pins 2 and 3 of the Mode DIP switch

to ON. Use this setting to operate a single fixture with

the remote control. If multiple fixtures are connected, set

only one to be the master.

If the Detonator is connected to multiple fixtures, all

fixtures except the master shall be set as slave fixtures,

with pin 2 of the Mode DIP switch ON and pin 3 OFF.

OPERATION

INTENSITY

Flash intensity is controlled from minimum (blackout) to maximum with the

Intensity fader.

The maximum intensity is reduced in low power mode, which is selected on pin 6

of the Mode DIP switch.

FLASH RATE

Flash rate is controlled from 0 to 25 flashes per second on 50 Hz power supplies,

or 0 to 30 flashes per second on 60 Hz power supplies, with the flash rate fader.

The Run/Stop button toggles continuous flashing on and off. The indicator diode

is green when running and red when stopped.

CHASE/SYNC

The Chase/Sync button toggles between staggered and simultaneous flashing of

multiple fixtures. The indicator diode blinks in chase mode and remains on in

Sync mode.

BLINDER EFFECT

The blinder effect is controlled with the momentary Blinder Effect button. The

intensity is controlled with the Intensity fader. Lamp power is electronically

regulated to prevent the lamp from overheating.

SINGLE FLASH

Single flashes can be achieved by pressing the Single Flash button with

continuous flash stopped.

The flash rate cycle can be restarted, for example to synchronize with a beat, by

pressing the Single Flash button while continuous flash is running.

2 3 4 516

Detonator master

mode setting

2 3 4 516

Detonator slave

mode setting

Page is loading ...

Martin ATOMIC 3000 User manual

Brand: Martin

Model: ATOMIC 3000

Category: DJ controllers

Type: User manual

This manual is also suitable for

Atomic Colors

Download PDF

report

Martin ATOMIC 3000 User manual

This manual is also suitable for

Martin ATOMIC 3000 User manual

Related papers

Other documents