Bissell 5990 User manual

Brand: Bissell

Model: 5990

Category: Vacuum cleaners

Type: User manual

This manual is also suitable for

USER’S GUIDE

5770/5990/6100/6405 SERIES

Safety Instructions

Product View

Assembly

6-9

Operations

10-15

Maintenance and Care

16-17

Troubleshooting

Consumer Services

Replacement Parts

Warranty

ug203-1369_5770_706.indd 1ug203-1369_5770_706.indd 1 7/25/06 12:41:55 PM7/25/06 12:41:55 PM

Thank you for buying a BISSELL Healthy Home Vacuum™

www.bissell.com 800.237.7691

Everything we know about floor care went into the design and construction

of this complete, high-tech home cleaning system.

We trust that it will bring you many years of satisfaction. It is backed with a

limited two-year warranty. We also stand behind it with a knowledgeable,

dedicated Consumer Services department, so, should you ever have a

question, you’ll receive fast, considerate assistance.

My great-grandfather invented the floor sweeper in 1876. Today, BISSELL is

a global leader in the design, manufacture, and service of high quality

homecare products like your Healthy Home Vacuum.

Thanks again, from all of us at BISSELL.

Mark J. Bissell

President and Chief Executive Officer

ug203-1369_5770_706.indd 2ug203-1369_5770_706.indd 2 7/25/06 12:42:08 PM7/25/06 12:42:08 PM

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical

appliance, basic

precautions should be observed, including

the following:

READ ALL INSTRUCTIONS

BEFORE USING YOUR

UPRIGHT VACUUM.

Always connect to a polarized outlet (one slot is wider

than the other). Unplug from outlet when not in use and

before conducting maintenance.

WARNING: To reduce

the risk of fire, electric shock,

or injury:

■

Do not modify the polarized plug to fit a

non-polarized outlet or extension cord.

■

Do not leave vacuum cleaner unattended when it

is plugged in.

■

Unplug from outlet when not in use and

before servicing.

■

Do not use outdoors or on wet surfaces.

■

Do not allow children to operate vacuum

cleaner or use as a toy.

■

Close attention is necessary when used by or

near children.

■

Do not use for any purpose other than described in

this User’s Guide.

■

Use only manufacturer’s recommended

attachments.

■

Do not use with damaged cord or plug.

■

If appliance is not working as it should, has been

dropped, damaged, left outdoors, or dropped

into water, have it repaired at an authorized

service center.

■

Do not pull or carry by cord, use cord as a handle,

close a door on cord, or pull cord around sharp

edges or corners. Do not run appliance over cord.

Keep cord away from heated surfaces.

■

Do not unplug by pulling on cord. To unplug, grasp

the plug, not the cord.

■

Do not handle vacuum cleaner or plug with

wet hands.

■

Do not put any object into openings. Do not use with

any opening blocked; keep openings free of dust,

lint, hair, and anything that may reduce air flow.

■

Keep hair, loose clothing, fingers, and all parts of

body away from openings and moving parts.

■

Turn off all controls before plugging or unplugging

vacuum cleaner.

■

Use extra care when cleaning stairs.

■

Unplug before attaching the TurboBrush.

■

Do not pick up flammable materials (lighter fluid,

gasoline, kerosene, etc.) or use in the presence of

explosive liquids or vapors.

■

Do not pick up toxic material (chlorine bleach,

ammonia, drain cleaner, etc.).

■

Do not use vacuum cleaner in an enclosed space

filled with vapors given off by oil base paint, paint

thinner, some moth proofing substances, flammable

dust, or other explosive or toxic vapors.

■

Do not pick up hard or sharp objects such as

glass, nails, screws, coins, etc.

■

Do not pick up anything that is burning or smoking,

such as cigarettes, matches, or hot ashes.

■

Do not use without filters in place.

■

Use only on dry, indoor surfaces.

■

Keep appliance on a level surface.

■

Do not carry the vacuum cleaner while it is running.

■

Brush may unexpectedly restart. Unplug from

outlet when cleaning or servicing.

SAVE THESE

INSTRUCTIONS FOR

FUTURE USE

THIS APPLIANCE HAS

A POLARIZED PLUG.

To reduce the risk of electric shock, this appliance has a

polarized plug (one blade is wider than the other). This plug

will fit in a polarized outlet only one way. If the plug does

not fit fully in the outlet, reverse the plug. If it still does not

fit, contact a qualified electrician to install a proper outlet.

Do not change the plug in any way.

This model is for household use only.

www.bissell.com 800.237.7691

ug203-1369_5770_706.indd 3ug203-1369_5770_706.indd 3 7/25/06 12:42:09 PM7/25/06 12:42:09 PM

www.bissell.com 800.237.7691

Upper Handle

Hose

TurboBrush

Crevice Tool

Telescoping

Extension

Wand

Dirt Container

Headlight

Height

Adjustment

Dial

Brush

Furniture Protection

Guard

Release Button

Carrying Handle

Filter Door Latch

Screen

HEPA Filter

Cartridge (inside)

Filter Tray (foam

filter inside)

Brush Window

Power Switch

Brush Switch

Hose Collar

Combination Brush

Lower Hose Clip

Handle Release

Pedal

Quick Release

Cord Wraps

Hose

Wand

Wand Base

Diverter

Foot Hose

Power Cord

ug203-1369_5770_706.indd 4ug203-1369_5770_706.indd 4 7/25/06 12:42:11 PM7/25/06 12:42:11 PM

www.bissell.com 800.237.7691

Tool required: Phillips screwdriver

1. Slide upper handle onto lower handle. Insert

one screw into hole marked with an arrow

and tighten until snug.

2. Attach hose by lining up the tabs on the

collar with the corresponding notches on

the back of the vacuum as shown. Turn

clockwise to lock the hose into place.

3. Wrap the hose by routing it down and into

the lower hose clip then up and over the top

of the handle. Insert the hose wand fully into

the hose base.

Note: It is important that the hose is fully

inserted into the base for the suction air to

be directed properly to the foot during floor

vacuuming.

4. Store TurboBrush on the front of the handle

by aligning the slot at the bottom with the

tab and snapping into place.

5. Place crevice tool inside telescoping extension

wand. Store tools on vacuum as shown.

Assembling your vacuum

CAUTION:

Do not plug in your

vacuum cleaner until

you are familiar with

all instructions and

operating procedures.

ug203-1369_5770_706.indd 5ug203-1369_5770_706.indd 5 7/25/06 12:42:23 PM7/25/06 12:42:23 PM

Transporting your cleaner

Use the handle on the front to carry the cleaner

or place the cleaner in the upright position and

tip back to roll on the rear wheels.

Releasing the power cord

The upper and lower cord wraps rotate to allow

for quick and easy removal of the power cord.

Fingertip power switch

The power button is located at the top of the

vacuum handle.

To turn cleaner on, press button once.

To turn cleaner OFF, press button again.

Note: The rotating brush will not turn on

unless the unit is in the reclined position

and the brush switch is on.

Handle positions

Use your foot to pull the handle release pedal

back to recline the vacuum cleaner.

Height adjustment

There are seven height settings available for

various floor surfaces. Turn the dial on the foot of

the cleaner to the desired setting.

Lowest setting – For bare floors.

Medium settings – For short and medium pile

carpets.

High setting – For plush carpet.

Note: For optimal cleaning performance,

adjust to the lowest practical setting. If

your cleaner is difficult to push, adjust to

the next higher setting.

If the dial is difficult to turn, tilt the cleaner

back slightly to take the weight off The foot

while turning.

Using your vacuum cleaner

www.bissell.com 800.237.7691

ATTENTION:

Some Berber carpets have a

tendency to fuzz with wear.

Repeated strokes in the same

area may aggravate this

condition. Consider setting your

cleaner on a higher than normal

setting for this type of carpet.

ug203-1369_5770_706.indd 6ug203-1369_5770_706.indd 6 7/25/06 12:42:44 PM7/25/06 12:42:44 PM

Fingertip brush switch

The rotating brush is turned on or off using the

switch at the side of the top of the handle. The

brush will start rotating when the unit is reclined.

The brush should be on for most carpeted floors.

You may want to turn the brush off for bare floor

cleaning or other delicate surfaces.

To turn the brush ON, press button once.

To turn the brush OFF, press button again.

Brush auto shut-off feature

When your cleaner is in the upright position, the

brush will not rotate. The brush will rotate only

when the cleaner is in the reclined position and

the brush switch is on.

Microban

antimicrobial protection fights the

growth of odor causing bacteria, mold and

mildew in your vacuum. It is built-in to key

components during the manufacturing process

and won't wash off or wear away. Microban

provides continuous antimicrobial product

protection for the useful lifetime of the product

keeping your vacuum cleaner and fresher.

Note: This should not replace normal

cleaning and maintenance procedures.

Microban is a registered trademark of Microban Products Company.

Acarosan

Dust Mite Control

As part of a complete cleaning program, use

BISSELL Acarosan dust mite powder and spray.

To kill dust mites lurking in your home, use

the Acarosan powder on your carpet and rugs,

and use the spray on your bed, pillows and

upholstery. The Acarosan spray comes with a

trigger for easy use. Just untwist the cap on the

bottle, and replace with the trigger which has

been provided. Twist the trigger on to secure.

For complete use instructions and further

information, please see the labeled products or

log on to www.acarosan.com. To re-order, see

Replacement Parts on pg. 19.

Acarosan is a trademark of Allergopharma.

Using your vacuum continued

www.bissell.com 800.237.7691

Microban

antimicrobial product protection

ug203-1369_5770_706.indd 7ug203-1369_5770_706.indd 7 7/25/06 12:43:05 PM7/25/06 12:43:05 PM

1 Make sure the cleaner is in the upright

position.

2. Remove the hose wand from the wand

base. This automatically diverts the

suction to the hose. Unwind the hose from

the cleaner.

Note: To help prevent the machine from

tipping, the hose should remain in the

bottom hose clip.

3. Use the hose and wand alone or attach

any of the tools to the end of the hose

wand.

TurboBrush

Use rotating brush action for small areas such

as stairs and upholstery.

Note: Press gently when using the

TurboBrush to gain maximum cleaning.

Too much pressure could cause the brush

to stop rotating.

Combination brush

Use longer soft bristles for dusting.

Remove long bristle portion and use shorter stiff

bristles when agitation is needed to remove debris.

Crevice tool

Use in tight narrow spaces

Telescoping extension wand

Use with desired attachment for a longer reach. To

extend the wand, twist the collar to “Unlock” and

push away from you. Twist the collar to “Lock”

to lock into place. To retract, twist to unlock, pull

toward you and twist to relock.

All items may not be included with your model.

Other tools are available; to order, please refer to

page 18-19.

www.bissell.com 800.237.7691

Using the tools

ATTENTION:

Always place the vacuum

cleaner on the floor in its fully

upright position when using

tools. Placing the vacuum in

this position automatically

stops the rotating brush.

CAUTION:

To avoid personal injury

and to prevent the cleaner

from falling when cleaning

stairs, always place it at

the bottom of the stairs.

ug203-1369_5770_706.indd 8ug203-1369_5770_706.indd 8 7/25/06 12:43:11 PM7/25/06 12:43:11 PM

Empty the dirt container as soon as the dirt

reaches the “Full” line on the side of the container.

1. Press the release button on top of the

carrying handle to remove the dirt container.

2. Choose an emptying method. Method #2 is

recommended for allergy sufferers.

Method #1 – hold the dirt container over

trash can and push the emptying button to

open the bottom (2a). Close the bottom after

the dirt empties.

Method #2 – place a plastic bag over the bottom

of the dirt container. Push the emptying button

through the plastic to open the bottom (2b). After

the dust settles, close the bottom and remove

the bag to discard.

3. Replace dirt container on cleaner by aligning

the bottom and pushing back until it snaps

into place.

Emptying the dirt container

www.bissell.com 800.237.7691

CAUTION:

Make sure vacuum cleaner

has been switched off and

unplugged before removing

dirt container.

ug203-1369_5770_706.indd 9ug203-1369_5770_706.indd 9 7/25/06 12:43:26 PM7/25/06 12:43:26 PM

Cleaning the dirt container

Additional steps can be taken to clean the dirt

container as necessary.

1. Ensure the dirt container has been emptied.

2. Remove the lower portion by pressing the

front and back latches on the upper portion

as shown.

3. Clean the screen with a cloth or soft brush

to remove dust or debris.

4. If desired, the lower dirt container may be

washed in warm water. Make sure it is

completely dry before reassembling.

5. To reassemble, hold the carry handle and

place the upper portion into the lower

portion, lining up the front and back latches.

Push down until both latches click into place.

Make sure the dirt container is securely

assembled before replacing it on machine.

Cleaning the foam filter

The foam filter should be checked monthly and

washed as needed to maintain performance.

More or less frequent cleaning may be required

based on individual vacuuming habits and types

of debris picked up .

1. The foam filter is located in the tray

labeled "Filter" underneath the dirt

container. Pull the tray out to access

the filter.

2. Remove foam filter from tray and hold under

running water to wash. Mild detergent

may also be used if desired. Wring excess

water from filter. Air dry thoroughly before

replacing.

WARNING:

Do not operate the cleaner with a

damp or wet filter or without all

the filters in place.

www.bissell.com 800.237.7691

Maintenance and care

WARNING:

To reduce the risk of

electric shock, turn power

switch OFF and disconnect

polarized plug from electri-

cal outlet before perform-

ing maintenance or

troubleshooting checks.

ug203-1369_5770_706.indd 10ug203-1369_5770_706.indd 10 7/25/06 12:43:59 PM7/25/06 12:43:59 PM

Replacing the HEPA filter cartridge

The HEPA filter cartridge should be

replaced every six months or if suction

is declining. More or less frequent

replacing may be required based on

individual vacuuming habits and types of

debris picked up.

Note: To have the benefits of the

Airtight

™

HEPA System, you must use

the BISSELL HEPA filter cartridge.

1. To remove the HEPA filter cartridge,

push down on the filter door latch and

pull door away from the cleaner.

2. Lift the tab at the top of the HEPA filter

cartridge and pull cartridge away from

the cleaner.

3. Replace the used HEPA filter cartridge

with a new one.

Note: To avoid damaging the HEPA

filter cartridge and reducing its

filtration capabilities, be careful not

to touch the filter material. The HEPA

filter cartridge is not washable.

www.bissell.com 800.237.7691

Maintenance and care continued

ug203-1369_5770_706.indd 11ug203-1369_5770_706.indd 11 7/25/06 12:44:24 PM7/25/06 12:44:24 PM

Clearing clogs

Low suction or poor pickup may be due to

a clog in the vacuum cleaner. If you notice

a change in the sound of the motor or a

reduction in the spinning action in the dirt

container, check for a clog.

If there is no suction or if suction is reduced

at the hose, follow these steps to check for

and clear the clog:

1. Unplug cleaner from electrical outlet.

2. Check the foam filter and clean as

necessary (see cleaning your foam filter

on page 10).

3. Check the HEPA filter and replace if

necessary (see replacing the HEPA filter

cartridge on page 11).

4. Check to see if dirt container is full.

Empty if needed.

5. Remove lower portion of dirt container.

Clean the screen and check center

tubes for dirt accumulation.

6. While dirt container is removed, check

dirt inlet for clogs.

7. Remove the hose from the cleaner by

twisting the collar counterclockwise.

Straighten the hose and check for a clog.

8. Check diverter area at back of machine

for diverter position and clogs. When the

hose wand is removed from the base,

the diverter should be up (8a). If a clog is

visible near the diverter, the plastic cover

may be removed to clear the clog by

removing the 7 screws as shown (8b).

Maintenance and care continued

www.bissell.com 800.237.7691

WARNING:

To reduce the risk of

electric shock, turn power

switch off and discon-

nect polarized plug from

electrical outlet before

performing maintenance or

troubleshooting checks.

ug203-1369_5770_706.indd 12ug203-1369_5770_706.indd 12 7/25/06 12:44:36 PM7/25/06 12:44:36 PM

Clearing clogs continued

If suction is normal at the hose, follow these steps

to check for and clear the clog for floor cleaning:

1. Check diverter area at back of machine for

diverter position and clogs. When the hose

wand is inserted in the base, the diverter

should be down. If a clog is visible near the

diverter, the plastic cover may be removed to

clear the clog by removing the 7 screws as

shown in illustration 8b above.

2. Check the foot hose for clogs (2a). If you are

not able to tell from the outside if a clog is

present, remove the bottom 4 screws from

the diverter cover to loosen and straighten

the foot hose (2b).

Remove any clogs found and fully

reassemble the cleaner before attempting to

check suction again or using the cleaner.

Thermal Motor Protection

An internal thermal protector has been designed

into your cleaner to protect it from overheating.

When the thermal protector activates, the main

vacuum motor will stop operating. If this happens,

proceed as follows.

1. Turn the cleaner OFF and unplug from

electrical outlet.

2. Check the cleaner for the source of over-

heating problem (i.e. full dirt cup, dirty filters

or clog).

3. Fix the problem by following the steps in the

maintenance section of the user guide.

4. When the motor cools for approximately 30

minutes, the thermal protector automati-

cally resets and cleaning may continue. If

the cleaner will not turn on or the thermal

protector continues to activate, your cleaner

may need servicing. Call BISSELL Consumer

Services or visit the website.

Note: The thermal protector controls the

main vacuum motor only, not the brush

motor. If the thermal protector activates,

the brush will continue to operate normally;

however, there will be no suction.

www.bissell.com 800.237.7691

Maintenance and care continued

ug203-1369_5770_706.indd 13ug203-1369_5770_706.indd 13 7/25/06 12:45:20 PM7/25/06 12:45:20 PM

www.bissell.com 800.237.7691

Maintenance and care continued

Brush reset

If something becomes lodged in the foot and the

brush shuts off, turn the cleaner off and unplug

from the outlet. Remove the obstruction. The

brush will automatically reset when the cleaner

is plugged in and turned back on.

Brush maintenance

The rotating brush should be checked regularly

for accumulating debris that might reduce the

cleaning performance of your vacuum.

1. Unplug cleaner from electrical outlet.

2. Recline the handle and turn your cleaner

over so the bottom side is up.

3. Carefully cut away any visible hair, fibers

or debris from the brush roll.

Do not attempt to disassemble the vacuum foot

or to remove the brush roll. If you feel it needs to

be checked or replaced, call BISSELL Consumer

Services or visit the website to locate an

authorized service center.

Belt maintenance

The brush belt is designed to last the useful life

of the cleaner when used according to all

instructions in the user guide under normal

household conditions. If you feel that it needs to

be checked or replaced, call BISSELL Consumer

Services or visit the website to locate an authorized

service center. Do no attempt to disassemble the

vacuum foot or to change the belt.

CAUTION:

To reduce the risk of injury

from moving parts, turn off

the vacuum cleaner and

disconnect power plug from

electrical outlet.

ug203-1369_5770_706.indd 14ug203-1369_5770_706.indd 14 7/25/06 12:45:48 PM7/25/06 12:45:48 PM

www.bissell.com 800.237.7691

Changing the light bulb

1. Unplug cleaner from electrical outlet.

2. Recline handle for easier access to light bulb

and remove screw to lift off lens.

3. Remove the bulb by grasping bulb and pull-

ing straight out of the socket. Install the new

bulb by pushing gently into the socket until

the bulb snaps into place.

TurboBrush maintenance

The TurboBrush should be checked regularly for

clogs or debris wrapping around the brush.

1. Remove tool from hose or front of vacuum.

2. Twist collar so opening is at the top and lift

top cover to remove.

3. Remove the brush from the belt and clean

debris.

4. Replace the brush inside the belt and place

ends into slots on sides as shown.

5. Reposition top cover and twist collar until

opening is at the bottom to lock into place.

Maintenance and care continued

ug203-1369_5770_706.indd 15ug203-1369_5770_706.indd 15 7/25/06 12:45:48 PM7/25/06 12:45:48 PM

www.bissell.com 800.237.7691

Troubleshooting

Vacuum cleaner won’t turn on

Possible causes Remedies

1. Power cord not plugged in 1. Check electrical plug

2. Blown fuse/tripped breaker 2. Check/replace fuse or reset breaker.

3. Thermal protector activated 3. Allow cleaner to cool for 30 minutes, see

pg. 13.

Brush not rotating

Possible causes Remedies

1. Brush switch turned to “Off” 1. Make sure brush switch is in “On” position

2. Vacuum is in upright position 2. Recline vacuum to operate brush

3. Brush is jammed 3. Remove obstruction or debris (pg. 14),

unplug cleaner to reset brush (pg. 14)

4. Brush needs to be reset 4. Unplug cleaner to reset brush (pg. 14)

Vacuum cleaner won’t pick up or low suction

Possible causes Remedies

1. Incorrect height setting 1. Turn dial to lower setting

2. Hose wand not properly positioned 2. Make sure hose wand is fully seated in

base and diverter is in down position

3. Dirt container not installed properly 3. Check assembly of upper and lower portions,

correctly position and snap into place

4. Dirt container full 4. Empty dirt container

5. Clog in cleaner 5. Follow instructions on pg. 12-13 for

clearing clogs

6. Filters are dirty 6. Check and clean foam filter, check and

replace HEPA filter cartridge if needed

7. Hose not properly attached 7. Make sure hose collar is twisted to

lock position

WARNING:

To reduce the risk of

electric shock, turn

power OFF and discon-

nect polarized plug from

electrical outlet before

performing maintenance

or troubleshooting.

ug203-1369_5770_706.indd 16ug203-1369_5770_706.indd 16 7/25/06 12:46:06 PM7/25/06 12:46:06 PM

Troubleshooting continued

www.bissell.com 800.237.7691

Vacuum cleaner is difficult to push

Possible causes Remedies

1. Incorrect height setting 1. Turn dial to higher setting

Visible dust escaping from cleaner

Possible causes Remedies

1. Filter tray missing or not installed properly 1. Check filter tray to make sure it is

fully inserted

2. Foam filter missing or not installed properly 2. Check foam filter for correct installation

3. HEPA filter cartridge missing or not installed properly 3. Check HEPA filter cartridge for

correct installation

4. Dirt container not installed properly 4. Make sure dirt container is correctly

positioned and snapped into place

5. Dirt container not assembled properly 5. Check screen, upper and lower portions of

the dirt container for proper assembly

6. Hose not installed properly 6. Make sure hose wand is fully seated in

base, make sure foot hose is properly

attached to diverter area

7. Hole or crack in hose 7. Check hose for holes or cracks and replace

if needed

Other maintenance or service not included above should be performed by an

authorized service representative.

Thank you for selecting a BISSELL product.

If you should happen to need assistance during assembly or operations, call 1-800-237-7691

Please do not return this product to the store

For any questions or concerns, BISSELL is happy to be of service.

ug203-1369_5770_706.indd 17ug203-1369_5770_706.indd 17 7/25/06 12:46:06 PM7/25/06 12:46:06 PM

www.bissell.com 800.237.7691

For information about repairs or replacement parts, or questions about your warranty, call:

BISSELL Consumer Services

1-800-237-7691

Monday - Friday 8 a.m. — 10 p.m. EST

Saturday 9 a.m. — 8 p.m. EST

Or write:

BISSELL HOMECARE, INC

PO Box 3606

Grand Rapids MI 49501

ATTN: Consumer Services

Or visit the BISSELL website - www.bissell.com

When contacting BISSELL, have model number of cleaner available.

Please record your Model Number: ___________________

Please record your Purchase Date: ___________________

NOTE: Please keep your original sales receipt. It provides proof of date of purchase in the event

of a warranty claim. See Warranty on page 20 for details.

BISSELL Consumer Services

ug203-1369_5770_706.indd 18ug203-1369_5770_706.indd 18 7/25/06 12:46:06 PM7/25/06 12:46:06 PM

www.bissell.com 800.237.7691

You may purchase parts from your retailer, by calling BISSELL Consumer Services or by

visiting our website. Below is a list of common replacement parts*. While not all of these

parts may have come with your specific model, they are available for purchase if desired.

Please note, all attachments may not store on board your vacuum.

Item Part No. Part Name

1 3282 HEPA Filter Cartridge

2 203-1374 Foam Filter

3 203-1362 TurboBrush

4 203-1364 Telescoping Wand

5 203-1365 Combination Brush

6 203-1363 Crevice Tool

7 203-1359 Hose

8 203-1377 Light Bulb

9 552A Acarosan Dust Mite Powder

10 556A Acarosan Dust Mite Control Trigger Spray

*Not all parts are included with every model.

Replacement parts - BISSELL Healthy Home Vacuum™

1 23

4 5

789

ug203-1369_5770_706.indd 19ug203-1369_5770_706.indd 19 7/25/06 12:46:07 PM7/25/06 12:46:07 PM

www.bissell.com 800.237.7691

Warranty - BISSELL Healthy Home Vacuum™

This warranty gives you specific legal rights, and you may also have other rights which may vary from state to

state. If you need additional instruction regarding this warranty or have questions regarding what it may cover,

please contact BISSELL Consumer Services by E-mail, telephone, or regular mail as described below.

Limited Two Year Warranty

Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product BISSELL

Homecare, Inc. will repair or replace (with new or remanufactured components or products), at BISSELL’s option,

free of charge from the date of purchase by the original purchaser, for two years any defective or

malfunctioning part.

See information below on "If your BISSELL product should require service".

This warranty applies to product used for personal, and not commercial or rental service. This warranty does not apply

to fans or routine maintenance components such as filters, or brushes. Damage or malfunction caused by negligence,

abuse, neglect, unauthorized repair, or any other use not in accordance with the User's Guide is

not covered.

If your BISSELL product should require service:

Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in your area.

If you need information about repairs or replacement parts, or if you have questions about your warranty,

contact BISSELL Consumer Services.

Website or E-mail:

www.bissell.com

Use the “Customer Service” tab.

Or Call:

BISSELL Consumer Services

1-800-237-7691

Monday - Friday 8 a.m. - 10 p.m. ET

Saturday 9 a.m. - 8 p.m. ET

Or write:

BISSELL Homecare, Inc.

PO Box 3606

Grand Rapids MI 49501

ATTN: Consumer Services

BISSELL HOMECARE, INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE

ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE

OF THE PRODUCT.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above

limitation or exclusion may not apply to you.

*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY

THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES

EITHER ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY

OPERATION OF LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE TWO YEAR

DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.

Some states do not allow limitations on how long an implied warranty lasts, so

the above limitation may not apply to you.

Grand Rapids, Michigan

Part Number 203-1369

Rev 7/06

Visit our website at:

www.bissell.com

ug203-1369_5770_706.indd 20ug203-1369_5770_706.indd 20 7/25/06 12:46:18 PM7/25/06 12:46:18 PM

Bissell 5990 User manual

Brand: Bissell

Model: 5990

Category: Vacuum cleaners

Type: User manual

This manual is also suitable for

Download PDF

report

Bissell 5990 User manual

This manual is also suitable for

Bissell 5990 User manual

Related papers

Other documents