JVC AVO48WP30 User manual

Formodels:

AVo56WF30

AVo48WP30

!!!!!!!

(located at the rear of the television cabinet): StaPl e your sales receipt or invoice

to the inside cover of this guidel Keep this users guide in a convenient place for

_UtU[e referencel Keep the carton and origina! packaging for future use:

Serial Number

Model Number

LCT1237o001B=A

0502=TN=FAA=JIM

m NT FETY

CAUTION:To reduce the risk of efectric shock.

Do not remove cover (or back).

No user serviceable parts inside.

Refer servicing to qualified service personnel

The lightning flash with arrowhead symbol,

within an equilateral triangle is intended to

alert the user to the presence of uninsulated

"dangerous voltage" within the product's

enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

WARNING:

CAUTION:

TO PREVENT FiRE OR SHOCK HAZARDS, DO NOT

EXPOSE THIS TV SET TO RAIN OR MOISTURE.

TO iNSURE PERSONAL SAFETY, OBSERVE THE

FOLLOWING RULES REGARDING THE USE OF

THIS UNIT.

1) Operate only from the power source specified on the unit.

2) Avoid damaging the AC plug and power cord.

3) Avoid Improper installation and never position the unit where good

ventilation is unattainable.

4) Do not allow objects or liquid into the cabinet openings.

5) In the event of trouble, unplug the unit and call a service technician. Do

not attempt to repair it yourself or remove the rear cover.

Changes or modifications not approved by JVC could void the warranty.

* When you don't use this TV set for a long period of time, be sure to

disconnect both the power plug from the AC outlet and antenna for your

safety.

* To prevent electric shock do not use this polarized plug with an

extension cord, receptacle or other outlet unless the blades can be fully

inserted to prevent blade exposure.

iMPORTANT SAFEGUARDS

CAUTION:

Please read and retain for your safety.

Electricai energy can perform many useful functions. This TV set has been engineered and

manufactured to assure your personai safety. But improper use can reauJt in potential

electrical shock or fire hazards! in order not to defeat the safeguards incorporated in this TV

set, observe the following basic ruies for its instailation, use and servicing.

And also follow all warnings and instructions marked on your TV set.

1) Your TV set is equipped with a polarized AC line plug (one blade of the plug is wider than

the other).

(POLARIZED:TYPE)

This safety feature allows the plug to fit into the power outtet only one way. Should you be

unable to insert the plug fuity into the outlet, try reversing the plug.

Should it still fail to fit, contact your electrician=

2) Operate the TV set only from a power source as indicated on the TV set or refer to the

operating instructions for this information, if you are not sure of the type of power supply to

your home, consult your TV set dealer or local power company. For battery operation, refer

to the operating instructions.

3) Overloaded AC outlets and extension cords are dangerous, and so are frayed power cords

and broken plugs. They may result in a shock or fire hazard. Call your service technician for

replacement=

4) Do not allow anything to rest on or toil over the power cord, and do not place the TV set

where power cord is subject to traffic or abuse. This may result in a shock or fire hazard.

5) Do not use this TV set near water = for example, near a bathtub, washbowl, kitchen sink,

or laundry tub, in a wet basement, or near swimming pool, etc.

6) if an outside antenna is connected to the TV set, be sure the antenna system is grounded

so as to provide some protection against voltage surges and buiit=up static charges. Section

810 of the National Electrical Code provides information with respect to proper grounding of

the mast and supporting structure, grounding of the lead=in wire to an antenna discharge

unit, size of grounding conductors, location of antenna discharge unit, connection

requirements for the grounding electrode.

-- n

IMPORTANT RECYCUNG iNFORMATiON

This product utilizes both a Cathode Ray Tube (C RT} and other

components that contain lead° Disposal of these materials may be

regulated in your community due to environmental considerations.

For disposal or recycling information, p_ease contact your local

authorities, or the Electronic industries Alliance: http:!iwww.eiae.org

7) An outside antenna system should not be located in the vicinity of overhead power lines or

other electric light or power circuits, or where it can fait into such power lines or circuits.

When installing an outside antenna system, extreme care should be taken to keep from

touching such power lines or circuits as contact with them might be fatal.

EXAMPLE OF ANTENNA GROUNDING

AS PER NATIONAL ELECTRICAL CODE

_-- DISCHARGEUNIT

(NEC SECTION81_Z_)

ELECFR_C

SEF_CICE GROUNDINGCONDUCTORS

_ NR SERVICEGROUNDING

ELECFRODE SYS-fEN

NEC NATIONALELEC[RIC CODE (_C A_FLCLE 2S0_ PaRr H)

8) TV sets are provided with ventilation openings in the cabinet to atiow heat generated during

operation to be released.

Therefore:

-- Never block the bottom ventilation slots of a portable TV set by placing it on a bed, sofa,

rug, etc.

-- Never place a TV set in a "buiitqn" enclosure unless proper ventilation is provided.

-- Never cover the openings with a cloth or other material.

-- Never place the TV set near or over a radiator or heat register.

9) To avoid personal injury:

-- Do not place a TV set on a sloping shelf unless properly secured.

-- Use only a cart or stand recommended by the TV set manufacturer.

-- Do not try to roll a cart with small casters across thresholds or deep pite carpets.

-- Wail or shelf mounting should follow the manufacturer's instructions, and should use a

mounting kit approved by the manufacturer.

lo)

11)

12)

Caution children about dropping or pushing objects into the TV set through cabinet

openings. Some internal parts carry hazardous voltages and contact can result in a fire or

electrical shock.

Unplug the TV set from the wail outlet before cleaning. Do not use liquid or an aeroso[

cleaner.

Never add accessories to a TV set that has not been designed for this purpose. Such

additions may result in a hazard.

13) ForaddedprotectionoftheTVsetduringalightningstormorwhentheTVsetistobeleft

unattendedforanextendedperiodoftime,unplugitfromthewaitoutletanddisconnect

theantenna.Thiswillpreventdamagetoproductduetolightningstormsorpowerline

surges.

14)ATVsetandcartcombinationshouldbemovedwithcare.Quickstops,excessiveforce,

andunevensurfacesmaycausetheTVsetandcartcombinationtooverturn.

15) Unplug this TV set from the wail outlet and refer servicing to qualified service personnel

under the following conditions:

A. When the power cord or plug is damaged or frayed.

B. If liquid has been spilled into the TV set.

C. If the TV set has been exposed to rain or water.

D. If the TV set does not operate normatiy by following the operating instructions. Adjust

only those controls that are covered in the operating instructions as improper

adjustment of other controls may result in damage and will often require extensive work

by a qualified technician to restore the TV set to normal operation.

E. If the TV set has been dropped or damaged in any way.

F. When the TV set exhibits a distinct change in performance -- this indicates a need for

service.

16) Do not attempt to service this TV set yourself as opening or removing covers may expose

you to dangerous voltage or other hazards. Refer all servicing to qualified service

personnel.

17) When replacement parts are required, have the service technician verify in writing that the

replacement parts he uses have the same safety characteristics as the original parts. Use

of manufacturer's specified replacement parts can prevent fire, shock, or other hazards.

18) Upon completion of any service or repairs to this TV set, please ask the service technician

to perform the safety check described in the manufacturer's service literature.

19) When a TV set reaches the end of it's useful life, improper disposai couid resuit in a

picture tube implosion. Ask a qualified service technician to dispose the TV set.

2o) Note to CATV system installer.

This reminder is provided to call the CATV system instal[er's attention to Article 820=40 of

the NEC that provides guidelines for proper grounding and, in particular, specifies that the

cable ground shall be connected to the grounding system of the building, as close to the

point of cable entry as practical

Unpacking YourTeievision, , , 8

Quick Setup ............... 9

CONNECTIONS ......... 12

Front Panel Diagram ........... 12

Rear Panel Diagram ........... 12

Connecting to Cable or an Antenna .... 13

Cable and VCR Connections ...... 14

Connecting to a DVD Player,

DTV Decoder and D-VHS ......... 15

Connecting to a Digital

TV Receiver w!HDCP ........... !6

Connecting to a DVD Player ........ !7

Connecting to JVC AV Compu Link Ill , , ,!8

Connecting Devices to the Front Panel , , 19

Connecting to an External Amplifier , , , 20

Connecting to the Surround Amplifier , , , 20

Remote Control ......... 21

Installing the batteries .......... 21

Remote Control Basics .......... 21

Remote Programming ..... 22

Setting CATV, VCR, and DVD Codes , , , 22

Cable Box or Satellite Setup ....... 22

VCR Setup ................ 23

DVD Setup ................ 24

Search Codes .............. 25

Onsereen Menus ........ 26

Onscreen Menu System ......... 26

Using the Onscreen Menus ........ 27

Plug In Menu ............... 28

Language ........... 28

Auto Tuner Setup ....... 29

Set Clock ........... 30

Auto ......... 30

Manual ....... 30

Finish .............. 30

Initial Setup ............... 31

Auto Tuner Setup ....... 31

Auto Demo .......... 31

Channel Summary ....... 32

Channel Summary= Lock , , , 32

Channel Guard Message .... 32

Oneereen Menus (Continued)

V=Ohip .................. 33

US Rating System ....... 33

Viewing Guidelines ...... 33

MPAA Ratings ......... 34

Set Ratings Guidelines ..... 85

To Set TV Ratings Levels , , , 85

To Set Movie Ratings Levels , 86

Unrated Programs ....... 36

VVarning Message ....... 36

Canadian V-Chip Ratings , , 37

Set Lock Code ......... 38

Initial Setup 2 .............. 39

Language ........... 39

Closed Caption ........ 89

Front Panel Lock ....... 40

Auto Shut Off .......... 41

Digital-In ........... 41

Picture Adjust .............. 42

Tint .............. 42

Color ............. 42

Picture ............. 43

Bright ............. 43

Detail ............. 43

Picture Adjust 2 ............. 44

Color Temperature ....... 44

Dig, Noise Clear ........ 44

Noise Muting ......... 44

Sound Adjust .............. 45

Bass ............. 45

Treble ............. 45

Balance ............ 45

MTS .............. 46

Sound Advice ......... 46

Clock/Timers .............. 47

Clock Timers ......... 47

Set Clock ........... 47

On/Off Timer ......... 47

Setting the On!Off Timer , , , 48

Initial Setup 3 .............. 49

Vertical Position ........ 49

Center Oh Input ........ 50

XDS ID ............ 50

Power Indicator ........ 50

Aspect .................. 51

Aspect ............. 51

Aspect Ratios ......... 51

Adjusting CRT Color Convergence .... 52

6

Ta

Button Functions ........ 53

SPLIT .................. 53

SWAP .................. 53

FREEZE ................. 53

SELECT ................. 58

ENTER ................. 58

INDEX .................. 54

POP ................. 54

MENU .................. 55

EXIT ................... 55

DISPLAY ................. 55

SLEEP TIMER .............. 55

BBE ................... 56

HYPER SURROUND .......... 56

MUTING ................. 56

VIDEO STATUS ............. 56

NATURAL CINEMA ........... 56

ASPECT ................. 56

NUMBER BUTTONS = 10 KEY PAD . . . 57

100+ BUTTON .............. 57

RETURN+ ................ 57

V_CHIP ................. 57

INPUT .................. 58

MENU (On TV's Front Panet) ...... 58

LIGHT .................. 58

VCR BUTTONS ............. 59

DVD BUTTONS ............. 59

TViCATV SWITCH ............ 59

VCR/DVD SWITCH ........... 59

Appendices ........... 60

Troubleshooting ............. 60

Appendix A ............... 62

Limited Warranty ............. 68

Authorized Service Centers ....... 65

Specifications .............. 66

of

7

n

Thank you for your purchase of JVC's model AV_56WP30 or AVo48WP30 Color Television.

Before you begin setting up your new television, please check to make sure you have all of the

following items, in addition to this guide, your television box should include:

1 Television 1 Remote Control 2 AA Batteries

ii 1 1

_vc

Once you have unpacked you[ ielevision, the next Step is to €onnept it to you[m

antenn_Jcab!e or satellite system and to connect the audio/video devices you want to use j

with your television. To make these connections you will use plugs like the ones illustrated I

below j

RF Connectors

Used to connect a

coaxial cable from an

external antenna or Cable

TV system.

A/V input Plug

Used to connect

audio/video devices like

VCRs, DVD players,

stereo amplifiers, game

consoles, etc.

S-Video Hug

Used to make video

connections with VCRs,

DVDs, Camcorders, etc

(optional).

AV Compu Link CaMe

Used to connect JVC

AV Compu Link

capable components for

an automated home

theater.

We recommend that before you start using your new television, you read your entire User's

Guide so you can learn about your new television's many great features. But if you're anxious

to start using your television right away, a quick setup guide follows on the next three pages.

Getting Started

These quick setup pages will provide you, in three easy steps, with the basic information you

need to begin using your new television right away, This information includes basic instructions

on operating your remote control, making a simple cable!antenna and optional VCR connection

and, finally, information on programming your television's Auto Tuner.

if you have questions, or for more detailed information on any of these steps, please consult

other sections of this manual.

Step One -The Remote Control

The remote control is the key to operating your television's many great features. Before you

can operate your remote control, you first need to install the batteries (included).

Slide the cover on the back of the remote down towards the bottom of the remote control.

insert two batteries (included) carefully noting the "+" and "-" markings, placing the "-" end in

the unit first. Slide the cover back into place.

Basic Operation

Turn the television on and off by pressing the POWER button at the top right corner of the

remote.

Power Button Key Feature Buttons

The four key feature buttons at the center of the remote can be used for basic operation of the

television. The top and bottom buttons will scan forward and back through the available

channels. The right and left buttons will turn the volume up or down. These buttons are atso

marked with four arrows and are atso used with JVC's onscreen menu system. You will need

to use these buttons later in the Quick Setup.

The next step is to connect your television to an antenna or cable.

Proceed to Step Two

Step Two o Making Basic Connections

Next you will need to connect your television to an antenna, VCR or cable system. The most

basic VCR and antenna!cable connection is shown below. For more detaiIed connections,

such as ones where a cable box is required, or connecting with a combination of a cable box

and VCR, home stereo system, etc., see pages 12 to 20.

Cable or Antenna

Output

_q

TV Rear Panel __j_

(RF Input) Cable/RF connector

1) Connect an RF Cable from the wail outlet into the RF Cable In on the back of the TV.

Connecting to a VCR

WALL VCR

CABLE or ANTENNA OUT

BACK of TV

1) Connect the Red Cable from VCR Audio Output into the Red TV Audio In.

2) Connect the White Cable from VCR Audio Output into the White TV Audio In.

3) Connect the Yeltow Cable from VCR Output into the YeItow TV Video In, OR Connect an

RF Cable from VCR RF Cable Out into the RF Cable In on the back of the TV.

NOTE:

• White, Yellow and Red are the most common colors for VCR Cables. Some models may

vary in color. Please consult the user's manual for your VCR Player for more information.

• See page 23 for instructions on programming your remote control to operate the basic

functions of your VCR Player.

1

Proceed to Step Three

Step Three-The Plug in Menu

When you turn your television on for the first time, the Plug In Menu wilt appear. This menu

sets some of the basic settings for your television. A complete description of the Plug In Menu

can be found starting on page 28. We recommend you complete the Plug In Menu items

before you start using your television. To begin watching your television right away you only

need to run the Auto Tuner Setup. This lets your television learn the channels it is able to

receive clearly. To run the Auto Tuner Setup, follow the steps below.

PLUG IN MENU

F LANGUAGE FRE SPA

OPERATE BY EXIT BY

Press the a,_' buttons to move to AUTO TUNER SETUP

Press the _ _ buttons to begin AUTO TUNER SETUP

AUTO TUNERSETUP :

tUNERMODEi CAbBiE

SELECT BY

OPERATEBY EXIT BY

_ To choose CABLE (if you are connected to a cable system) or AIR (if you use

an antenna)

AT To move to START

_ To start Auto Tuner Setup

The Auto Tuner will now memorize all of the clear, active channels your television can

receive. This will take roughly one or two minutes.

The Auto Tuner is finished when the message PROGRAMMING OVER! appears on screen.

Your Quick Setup is now complete. You can now begin watching your television, or you can

continue on in this guide for more information on connecting audio/video devices, programming

your remote control, or using the JVC onscreen menu system to customize your television

viewing experience.

! TheQuickSetupiseomptete 11

Connections

Front Panel Diagram

Rear Panel Diagram

@

2-- 3

75_

cVHF/ UHF_

° ® -°_

....® ® _

.....®®®

_'UD_O V_DEO S-WbEO

C_PONE_ r VIDEOi

12

Co

Connecting to Cable or an Antenna

There are three basic types of antenna or cable connections:

If you have an antenna or have a cable system that does not require you use a cable

box to select channels, please refer to Diagram #1.

• If you have a cable system that requires the use of a cable box to access all the

channels, please refer to Diagram #2.

If you have a cable system that requires the use of a cable box [o access certain

premium channels, but not "basic" cable channels, please refer to Diagram #3,

, For your convenience connection to a VCR is also shown Jnthe following diagrams. A

VCR is no1 necessary for operation of the television or Picture OUT or Picture POP

function. You may omit the VCR from your connections if you wish.

For instructions on connecting a VCR only, please see the Quick Setup on page 10.

, For information on using POP, please see page 54

Diagram #1

Cable or Antenna

Output

TV Rear Panel

(RF input)

j Cabte/RF connector

1) Connect an RF Cable from the wail outtet into the RF Cable In on the back of the TV.

Connecting to a Cable Box

Diagram #2 CaMe or Antenna

Output

B

TV Rear Panel

(RF input)

1) Connect an RF Cable from the wait outlet into the RF Cable In on the Cable Box.

2) Connect an RF cable from the Cable Out on the cable box into the RF Cable In on the back

of the TV.

NOTE:

Please see page 54 for more information on using the POP feature with a cable box,

1

Connecting to a Cable Box and VCR

Diagram #3

Cable or Antenna

Output

B,

TV Rear Panel

VCR

v

VLR

1) Connect an RF Cable from the wait outlet into the RF Cable Box In.

2) Connect an RF Cable from the Cable Box Out into the VCR In.

3) Connect an RF Cable from the VCR Out into the RF in on the back of the TV.

4) Connect the Red Cable from VCR Right Audio Output into the Red TV Audio In.

5) Connect the White Cable from VCR Left Audio Output into the White TV Audio In.

6) Connect the Yellow Cable from VCR Output into the Yellow TV Video in, OR Connect an

S-Video Cable from VCR S=Video Out into the S-Video in on the back of the TV.

NOTE:

• White, Yellow and Red are the most common colors for VCR Cables, Some models may

vary in color, Please consult the user's manual for your VCR Player for more information,

• See page 23 for instructions on programming your remote control to operate the basic

functions of your VCR Player,

The ConnectiOn diagrams are intended to show some basic general connections,

Some cabJe companies may require speciat connections to properly use your

te!evision or 2=tuner MULTi SCREEN function. If you follow these diagrams and either

the te!evision or PiP does not work proper!y, contact your Jocal cabJe operato r for

mote connection information. Please see page 54 for more information on the POP

feature.

14

Co

Connecting a DVD Player, DTV Decoder, and D°VHS

Your AV-56WP30 or AV-48WP30 television is HDTV and SDTV-Ready. This means it can

display High Definition television images when connected to a digital television receiver*. DTV

Decoders are available separately. For best image quality, we recommend using a DTV

Decoder which uses Component Video (Y, PB, PR) Output to connect to the television. The

diagram below shows how to connect a DTV Decoder with using the television's Component

Video-in jacks.

S-Video Connection

DTV Decoder

. / Component Connection

Green

Bed

1) Connect Green cable out from the DTV Decoder "Y" Video Output, in to TV "Y" Component

Input.

2) Connect Blue cable out from the DTV Decoder "PB" Video Output, in to TV "PB" Component

Input.

3) Connect Red cable out from the DTV Decoder "PR" Video Output, in to TV PR" Component

Input.

4) Connect White Audio cable out the DTV Decoder Left Audio Output, in to TV Left Audio

Input.

5) Connect Red Audio cable out the DTV Decoder Right Audio Output, in to TV Right Audio

Input.

Make sure you use the same numbered input for both the Component input and Audio

hputo For instance, if you use Component Input 2, atso use Audio Input 2.

• Green, blue and red are the most common colors for Component Video cables. Some

models may vary colors, please consult the user's manual for your DTV Decoder for more

information.

• Be careful not to confuse the red Component Video cable with the red audio cable. It is best

to complete one set of connections (Audio or Video) before starting the other to avoid

accidentally switching the cables.

[7 eo Ab0ot.DTVOpe,"t!o.

I The AV456WP30 Or AV_48WP30 can display 480p: #80J, 1080i and 720p signa! formats I

I using the Component V!deo Inputs. k cannot display !080p s!gnal. For H!gh Definit!0n I

l (HDTV) PiCtUre display a DTV decoder must be connected to the TV. 1

15

Connecting to a Digital TV Receiver w/HDCP

By inputting a high bandwidth Digitai Content Protection High Definition picture source to the

Digitaiqn terminal of this television, high-definition pictures can be displayed on the screen in

their digitai form. (This terminat is for use in the future when high bandwidth Digital Content

Protection DTV decoders and DVD players and D_VHS are put on the market.)

[

AUDIO G

After the connections

have been made,

tighten the screw to

secure the cables°

DIGITAL OUT

DTV decoder

1 Connect the DTV digital RGB output terminal to the digital input terminal of the television,

and then tighten the 2 screws.

2) Connect the DTV decoder left audio output to the DIGITAL-IN left audio input.

3) Connect the DTV decoder right audio output to the DIGITALqN right audio input.

• The Digitalqn terminal can only be used with 1080i, 720p and 480p picture signals. Set the

DTV decode DigitaFOut terminal output setting to 1080i, 720p or 480p. For detailed

information, refer to the DTV decoder instruction manual. If you can not display the picture

because your DTV decoder does not have a DigitaFOut terminal output setting, use the

component Video Input (or the S-Video Input or Video Input). (Refer to page 15) In this case

the picture wilt be displayed as an analog signal.

• The Digitatqn terminal is not compatible with the picture signal of a personal computer.

• Use a DVI-D Single Link 19-pin cable (commercially available) in order to digitally connect

the television with a DTV decoder.

If 480p signals (640x480 or 720x480) are displayed on the screen, the horizontal balance may

be stightly shifted. In cases such as this, the horizontal baiance can be adjusted by accessing

"DIGITAL-IN" in the iNITiAL SETUP Menu. (Refer to page 41 .)

16

Connecting a DVD Player

You can use the Component Video input jacks to connect a DVD player to your television= To

connect a DVD player, please follow the steps listed below=

1) Connect Green cable out from the DVD Player "Y" Video Output, in to TV "Y" Component

input.

2) Connect Blue cable out from the DVD Player "PB" Video Output, in to TV "PB" Component

Input.

3) Connect Red cable out from the DVD Player "PR" Video Output, in to TV PR" Component

Input.

4) Connect White Audio cable out the DVD Player Left Audio Output, in to TV Left Audio Input.

5) Connect Red Audio cable out the DVD Player Right Audio Output, in to TV Right Audio

Input.

Make sure you use the same numbered input for both the Component Input and Audio

Input. For instance, if you use Component input 3, also use Audio input 3.

• Green, blue and red are the most common colors for Component Video cables. Some

models may vary colors, please consult the user's manual for your DVD Player for more

information.

• Be careful not to confuse the red Component Video cable with the red audio cable, it is best

to complete one set of connections (Audio or Video) before starting the other to avoid

accidentally switching the cables.

• if your DVD player does not have a Component Video output, you may connect it using an

S-Video cable. See your DVD player's owners manual for more information on making an

S-Video connection.

_ / S-Video Connection

s

__il! /_,.F-_ Component Connection

//111 o,oo°

/ / I1_ '

O _---4 _ F<---- P'_ _.P.I . .Pr_ Red

2L

BACK of ]1/

R L

.....o I ....ol .....o

17

ons

Connecting to AV Compu°Link IH

JVC's AV Compu Link Ill feature makes playing video tapes totally automatic. Simply insert a

pre_recorded tape* into your JVC_brand VCR and the VCR will automatically turn on and begin

playback. At the same time, using the AV Compu Link, the VCR sends a signal to the television

telling it to turn on and switch to the proper video input to watch a video tape.

• The AV Compu Link cable may be included with the JVC AV Compu Link accessory you wish

to connect, if it is not, contact an authorized JVC Service Center for part # EWP 805-012.

• AV Compu Link Ill can only be used with JVC-brand products.

m

.

VCR

AV

Cornpu

Link

Swap

To Connect: Plug one end of the AV Compu Link cable into the AV Compu Link input on your

VCR or other Compu Link device. Plug the other end of the AV Compu Link cable into the AV

Compu Link input at the rear of the television.

Notes:

* In order for the VCR playback to begin automatically the recording 1aDsmust De removed

from the VHS tape. If the tab is in place_automatic switching will occur when you push the

VCR's PLAY but[on

, The AV Compu Link cable has a male 3.5 mm (mono) plug on each end.

- If your JVC-brand VCR has "A Code/B Code Remote Control Switching (see your VCR's

instruction book), usin9 VCR A Code will switch the TV to input 1. If you use Input 1 for

video input from your cable box. use VCR B Code to select the TV Video Input 2.

o To connect a JVC HiFi receiver or amplifier for a completely automated home theater, see

the HiFi's connection instructions for detailed connection information.

o AV COMPU UNK Ill is compatible with all JVC AV COMPU LINK l!! devices

- The AV-56WP30 or AV-48WP30 can also receive Compu-Link signals from a DVD player.

For details on operating a DVD player with AV Compu Link, please see your DVD player's

owners manual.

1

Connecting Devices to the Front Panel inputs

A set of inputs (Input=4) are provided for your convenience on the front panel of the

AV=56WP30 or AV-48WP30. The inputs are located behind the door at the center of the front

panel below the indicator lights. These inputs are designed for the easy connection of devices

like camcorders or game consoles which are not permanent parts of your home entertainment

center.

To access the front panel jacks, gently pull the tab on the door torwards you to open it.

To connect a device like a camcorder:

1 Connect the yellow video cable from the device's Video Output jack to the TV's Video Input

jack, or connect an S=Video cable from the camcorder's S=Video Output to the TV's S=Video

Input.

2) Connect the white (or black) audio cable from the device's Left Audio Output jack to the T%/'s

Left Audio Input jack.

3) Connect the red audio cable from the device's Right Audio Output jack to the TV's Right

Audio Input jack.

• If you are connecting a mono sound device it will have only one audio out jack. Connect it to

the TV's Ieft audio input jack.

• The device witl be available on Input 4 on the Input Menu (see page 58) if the connection shown

above is used.

• Please consult your camcorder or other device's owners manual for more information on its

operation.

1

ons

Connecting to an E×ternai Amplifier

TV Rear Panel

Left Right

Front Front

Speaker Speaker

1) Connect the White Audio Cable from the TV's Left Audio Output Jack to the Amplifier's Left

Audio Input Jack.

2) Connect the Red Audio Cable from the TV's Right Audio Output Jack to the Amplifier's

Right Audio Input Jack.

Connecting to the Surround Amplifier

FRONT FRONT SURROUND

SPEAKER INPU

16£_ 45W MAX

RED Center Speaker Out

_dJ

1) Connect the BLACK speaker cable from the TV's SPEAKER iNPUT Q terminal to the

surround amplifier's center speaker output 0 terminal

2) Connect the RED speaker cable from the TV's SPEAKER iNPUT (_ terminal to the

surround amplifier's center speaker output q_ terminal.

Page is loading ...

JVC AVO48WP30 User manual

This manual is also suitable for

JVC AVO48WP30 User manual

Related papers

Other documents