2. WEG
  3. CFW11

WEG CFW11 User guide

  • Hello! I am an AI chatbot trained to assist you with the WEG CFW11 User guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
5
English

Figure 1 -Identificationofslotsoftheoptionalmodules
-slot1:white
-slot2:yellow
-slot3:green
Installation, Configuration and Operation Guide
Temperature Transducers Module IOE
l. SAFETY INFORMATION
Allsafetyproceduresdescribedinthemanualmustbefollowed.
ll. GENERAL INFORMATION
Thisuserguideprovidesinformationforinstallation,configurationandoperation
oftheoptionalmodulesIOE-01,IOE-02andIOE-03.
ThesemodulesareusedtoconnecttemperaturesensorsofthetypePTC(IOE-01),
PTC100(IOE-02)andKTY84(IOE-03).
NOTE!
TheIOE-0xaccessoriescanbeusedonlywithCFW-11invertersthathave
softwareversionV2.00orhigher.
lll. PACKAGE CONTENTS
-Accessorymoduleinanti-staticpackaging.
-Installation,configurationandoperationguide.
-Fixingscrew.
1. MODULE INSTALLATION
TheoptionalboardmodulesareinstalleddirectlyintoslotsontheCFW-11control
module.
6
English
TocorrectlyinstallmodulesIOE-01,IOE-02andIOE-03,followthestepsbelow:
Step 1: Whilethedrive is powered off, remove the front cover of the CFW-11
(figure2);
Step 2:Carefullyconnectthemoduleintoslot1(figure3(a));
Step 3: Placeandfastenthefixingscrewofthemodule(figure3(b));
Step 4: ConnectthecablesofthesensorsintheXC12(IOE-01),XC13(IOE-02)
andXC14(IOE-03).
Figure 2 -Removalofthefrontcover
Figure 3 - Installationoftheoptionalmoduleintoslot
b
c
a
a
b
7
English
2. TECNICAL SPECIFICATIONS
2.1 Connection and Indications
XC12 Function Specications
1 FC1 CurrentsourceforSensor1 2mA±7%
2 SEN1 Sensor1input 0to10Vdc;Rin=442kΩ
3 GND* 0Vreferenceforthesensorsinput Isolatedfromthegroundoftheinverter
4 FC2 CurrentsourceforSensor2 2mA±7%
5 SEN2 Sensor2input 0to10Vdc;Rin=442kΩ
6 GND* 0Vreferenceforthesensorsinput Isolatedfromthegroundoftheinverter
7 FC3 CurrentsourceforSensor3 2mA±7%
8 SEN3 Sensor3input 0to10Vdc;Rin=442kΩ
9 GND* 0Vreferenceforthesensorsinput Isolatedfromthegroundoftheinverter
10 FC4 CurrentsourceforSensor4 2mA±7%
11 SEN4 Sensor4input 0to10Vdc;Rin=442kΩ
12 GND* 0Vreferenceforthesensorsinput Isolatedfromthegroundoftheinverter
13 FC5 CurrentsourceforSensor5 2mA±7%
14 SEN5 Sensor5input 0to10Vdc;Rin=442kΩ
15
GND* 0Vreferenceforthesensors Isolatedfromthegroundoftheinverter
16
17
18
PTC-1
PTC-3
PTC-2
PTC-4
PTC-5
Figure 4 - ConnectorXC12–IOE-01
Type PTC Simple and Triple
Alarm/Faultindicationvalue
(1)
PTCsimple:1300Ω±10%
PTCtriple:4000Ω±10%
ResetValue
PTCsimple:550Ω±10%
PTCtriple:1650Ω±10%
Note:
(1) Programmabletoalarmorfault.RefertotheCFW-11ProgrammingManualforfurtherdetails.
Table 1 - PTCinput’selectricalspecifications
8
English
XC13 Function Specications
1 FC1 CurrentsourceforSensor1 2mA±0.5%
2 SEN1 Sensor1input 0to0.41Vdc;Rin=1MΩ
3 GND* 0Vreferenceforthesensorsinput Isolatedfromthegroundoftheinverter
4 FC2 CurrentsourceforSensor2 2mA±0.5%
5 SEN2 Sensor2input 0to0.41Vdc;Rin=1MΩ
6 GND* 0Vreferenceforthesensorsinput Isolatedfromthegroundoftheinverter
7 FC3 CurrentsourceforSensor3 2mA±0.5%
8 SEN3 Sensor3input 0to0.41Vdc;Rin=1MΩ
9 GND* 0Vreferenceforthesensorsinput Isolatedfromthegroundoftheinverter
10 FC4 CurrentsourceforSensor4 2mA±0.5%
11 SEN4 Sensor4input 0to0.41Vdc;Rin=1MΩ
12 GND* 0Vreferenceforthesensorsinput Isolatedfromthegroundoftheinverter
13 FC5 CurrentsourceforSensor5 2mA±0.5%
14 SEN5 Sensor5input 0to0.41Vdc;Rin=442kΩ
15
GND* 0Vreferenceforthesensors Isolatedfromthegroundoftheinverter
16
17
18
PT100-1
PT100-3
PT100-2
PT100-4
PT100-5
Figure 5 - ConnectorXC13–IOE-02
ATTENTION!
Ifsensor1isnotusedconnectawirebetweenterminalsXC13:1and
2.Proceedinthesamewayforsensor2interconnectingXC13:4and
5, for the sensor 3 interconnecting XC13: 7 and 8, for the sensor 4
interconnectingXC13:10and11andforthesensor5interconnecting
XC13:13and14.
Temperature
Indications
(1)
Range -20to+200°C
Resolution 1°C
Accuracy ±5°C
FaultLevels
(1)
Adjustablebyparameters
AlarmLevels
(1)
10°Cbelowthefaultlevels
Standard EN60751
Note:
(1) SeethenumbersoftheparametersandfurtherdetailsintheCFW-11ProgrammingManual.
Table 2 - PT100inputselectricalspecifications
9
English
XC14 Function Specications
1 FC1 CurrentsourceforSensor1 1.03mA±2%
2 SEN1 Sensor1input 0to1.77Vdc;Rin=1MΩ
3 GND* 0Vreferenceforthesensorsinput Isolatedfromtheinverter’sground
4 FC2 CurrentsourceforSensor2 1.03mA±2%
5 SEN2 Sensor2input 0to1.77Vdc;Rin=1MΩ
6 GND* 0Vreferenceforthesensorsinput Isolatedfromtheinverter’sground
7 FC3 CurrentsourceforSensor3 1.03mA±2%
8 SEN3 Sensor3input 0to1.77Vdc;Rin=1MΩ
9 GND* 0Vreferenceforthesensorsinput Isolatedfromtheinverter’sground
10 FC4 CurrentsourceforSensor4 1.03mA±2%
11 SEN4 Sensor4input 0to1.77Vdc;Rin=1MΩ
12 GND* 0Vreferenceforthesensorsinput Isolatedfromtheinverter’sground
13 FC5 CurrentsourceforSensor5 1.03mA±2%
14 SEN5 Sensor5input 0to1.77Vdc;Rin=1MΩ
15
GND* 0Vreferenceforthesensors Isolatedfromtheinverter’sground
16
17
18
KTY84-1
KTY84-2
KTY84-3
KTY84-4
KTY84-5
Figure 6 - ConnectorXC14–IOE-03
ATTENTION!
Ifsensor1isnotusedconnectawirebetweenterminalsXC14:1and
2.Proceedinthesamewayforsensor2interconnectingXC14:4and
5, for the sensor 3 interconnecting XC14: 7 and 8, for the sensor 4
interconnectingXC14:10and11andforthesensor5interconnecting
XC14:13and14.
Temperature
Indications
(1)
Range -20to+200°C
Resolution 1°C
Accuracy ±10°C
FaultLevels
(1)
Adjustablebyparameters
AlarmLevels
(1)
10°Cbelowthefaultlevels
Note:
(1) Seethenumbersoftheparameters,faultnumbers,alarmsandfurtherdetailsintheCFW-11
ProgrammingManual.
Table 3 - KTY84inputselectricalspecifications
10
English
2.2 Cable Recommendations to Connect the Sensors
Useshieldedcableswithwiregaugebetween0.14mm
2
(26AWG)and1.5mm
2
(15AWG).Connecttheshieldinthecontrolgroundplate.RefertotheCFW-11
User’sGuideforfurtherdetails.
2.3 Insulation
Thecircuitconnectedinthesensorshavestronginsulationfromtheotherscircuits
inthecontrolboard.Butit’srecommendedthatallthesensorsbealwaysisolated
fromthelivepartsofthemotor.
3. FIRST TIME START-UP
Step 1: Afterinstallthemoduleandconnectedyourcables,energizetheinverter;
Step 2: Checkifthemodulewascorrectlyidentifiedbythecontrol:25xx(IOE-01),
23xx(IOE-02)or27xx(IOE-03);
Step 3: Setuptheparametersrelatedwiththeusedmoduleaccordingwiththe
applicationneeds.RefertotheCFW-11ProgrammingManualforfurther
details.
WEG Equipamentos Elétricos S.A.
Jaraguá do Sul - SC - Brazil
Phone 55 (47) 3276-4000 - Fax 55 (47) 3276-4020
São Paulo - SP - Brazil
Phone 55 (11) 5053-2300 - Fax 55 (11) 5052-4212
automacao@weg.net
www.weg.net
Document: 10000545263 / 01
/