VISUAL COMFORT CHC 5446 User manual

VISUAL COMFORT
Brand
VISUAL COMFORT
Model
CHC 5446
Type
User manual

VISUAL COMFORT CHC 5446 is a large chandelier with a striking design that can enhance the ambiance of any room. It requires assembly and comes with all the necessary components, including a mounting plate, canopy, chain, and collar ring. You'll need basic tools like measuring tape, wire cutters, slip-joint pliers, chain pliers, slotted screwdriver, wire strippers, and a Phillips screwdriver for installation. The chandelier accommodates multiple bulbs, offering ample lighting, and features crystal stands and drops that add a touch of elegance to its appearance.

VISUAL COMFORT CHC 5446 is a large chandelier with a striking design that can enhance the ambiance of any room. It requires assembly and comes with all the necessary components, including a mounting plate, canopy, chain, and collar ring. You'll need basic tools like measuring tape, wire cutters, slip-joint pliers, chain pliers, slotted screwdriver, wire strippers, and a Phillips screwdriver for installation. The chandelier accommodates multiple bulbs, offering ample lighting, and features crystal stands and drops that add a touch of elegance to its appearance.

1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Remove collar loop (D) from chain (H) by removing quick link (E).
3. Install mounting plate (B) to the junction box and secure with
mounting screws (C).
4. Secure collar loop (D) to mounting plate (B) using pliers to tighten
locknut.
5. Install canopy (F) to collar loop (D) and secure with collar ring (G).
6. Determine desired overall length, and amount of chain (H) needed.
Shorten chain using chain pliers. (Keep extra chain)
7. Attach chain (H) to collar loop (D) and fixture loop (I) using quick
links (E). Secure quick links (E).
8. Thread fixture wire and ground wire through chain (H).
NOTE: When you reach the collar loop (D), ensure there is no tension
on the wires. Cut excess wires, being sure to leave about 12” to reach
the junction box.
9. Separate two sides of molded wire, and strip insulation on each 5/8".
10. Loosen collar ring (G) and let canopy (F) slip down chain (H) carefully.
11. Twist all fixture wires together and slip through center hole of collar
loop (D).
NOTE: Untwist wires and separate to prepare for connection.
Alessa X-Large Chandelier
Item # CHC 5446
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver Slotted Screwdriver Chain Pliers
Slip Joint Pliers Measuring Tape Wire Cutters
Wire Strippers
NOTICE:
US
M
L
I
D
S
E
T
L(5PCS)
J(5PCS)
K(10PCS)
M
N(10PCS)
O(10PCS)
I
E
E
G
D
F
H
C
B
A
Diagram 1
Bulbs not included
P
Q
R
Diagram 2
J
J
J
J
J
K
K
K
K
K
K
K
K
K
KL
L
L
L
L
Diagram 3
O
O
O
O
O
O
O
ONN
N
N
N
N
N
N
N
N
O
O
Alessa X-Large Chandelier
Item # CHC 5446
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
12. Wrap fixture ground wire (bare copper) around the green grounding
screw (see diagram 1). Tighten. Continue fixture ground wire and
connect to supply ground wire (usually green or bare copper) using
wire nut (A).
NOTE: It is imperative that the fixture is grounded.
13. Connect fixture neutral wire (ribbed) to the supply neutral wire (usually
white) using wire nut (A).
14. Connect fixture hot wire (smooth with markings) to the supply hot
wire (usually black) using wire nut (A).
CAUTION: Do not reverse the hot and neutral connections.
15. Make sure all wire connections are tight, then carefully tuck into the
junction box.
16. Install canopy (F) to collar loop (D) and secure with collar ring (G).
17. Install light bulbs into the sockets.
Crystal Assembly - Use diagrams 2 & 3 to complete below:
1. Hang crystal stands (L) to bottom of ring (P), then hang opposite end
to top of middle ring (Q).
2. Hang crystal stands (O) to bottom of ring (Q), then hang opposite end
to holes on metal plate (R).
3. Hang crystal drops (J & K) to top of ring (P) .
4. Hang crystal drops (N) to bottom of ring (Q).
Care Instructions: Clean only with a soft dry cloth or feather duster. Do
Not use abrasive or chemical agents.
NOTICE:
US
M
L
I
D
S
E
T
L(5PCS)
J(5PCS)
K(10PCS)
M
N(10PCS)
O(10PCS)
I
E
E
G
D
F
H
C
B
A
Diagram 1
Bulbs not included
P
Q
R
Diagram 2
J
J
J
J
J
K
K
K
K
K
K
K
K
K
KL
L
L
L
L
Diagram 3
O
O
O
O
O
O
O
ONN
N
N
N
N
N
N
N
N
O
O
  • Page 1 1
  • Page 2 2

VISUAL COMFORT CHC 5446 User manual

VISUAL COMFORT
Brand
VISUAL COMFORT
Model
CHC 5446
Type
User manual

VISUAL COMFORT CHC 5446 is a large chandelier with a striking design that can enhance the ambiance of any room. It requires assembly and comes with all the necessary components, including a mounting plate, canopy, chain, and collar ring. You'll need basic tools like measuring tape, wire cutters, slip-joint pliers, chain pliers, slotted screwdriver, wire strippers, and a Phillips screwdriver for installation. The chandelier accommodates multiple bulbs, offering ample lighting, and features crystal stands and drops that add a touch of elegance to its appearance.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents