Swan SH16310N Installation guide

v1.0

Patio Heaters Assembly

Photo Guide

Models: SH16310N, SH16320N, SH16330N

Please read in conjunction with the printed manual

that came with the product

Help line: 0333 220 6050

Patio_Heaters_Assy.indd 1 03/05/2019 11:35

2

1. Lower body

2. Upper body

3. Base

4. Base cover

5. Cord grip

6. Screws for joint boards

7. Screws & washers for base

8. Joint boards

9. Allen key

You will also need a cross head screw driver. Assembly is much

easier with two people and reduces the risk of damaging the

product.

SH16310N - COLUMN PATIO HEATER

1 2 3

4

56

7

89

Patio_Heaters_Assy.indd 2 03/05/2019 11:35

3

SH16310N - COLUMN PATIO HEATER

Thread the plug and

cable from the upper

body (2) through the

channel in the lower

body (1)

Make sure it goes all

the way through.

Slide the upper body

(2) on to the lower

body (1)

Patio_Heaters_Assy.indd 3 03/05/2019 11:35

4

SH16310N - COLUMN PATIO HEATER

Fit the joint boards

and secure with the

screws (6) using the

allen key provided (9)

Turn the unit upside

down (put some cloth

down to prevent

scratches).

Put the base (3)

inside the base cover

(4) and thread the

plug and cord through

the hole in the middle

Patio_Heaters_Assy.indd 4 03/05/2019 11:35

5

SH16310N - COLUMN PATIO HEATER

Fasten the base to

the main unit using

the screws & wash-

ers (7)

Fasten the cord grip

(5). Make sure the lip

faces upwards

Refer to the manual that came with the product for operation guide

Patio_Heaters_Assy.indd 5 03/05/2019 11:35

6

SH16320N - BAR TABLE PATIO HEATER

1. Main body

2. Base cover

3. Base

4. Table top

5. Foot bracket

6. Allen keys - 1 large + 1 small

7. Screws & washers for base

8. Long screws + steel tubes

9. Screws for table top

You will also need a cross head screw driver. Assembly is much

easier with two people and reduces the risk of damaging the

product.

1

2

3

4

5

6

7

8

9

Patio_Heaters_Assy.indd 6 03/05/2019 11:35

7

SH16320N - BAR TABLE PATIO HEATER

Turn the main body

(1) upside down (put a

cloth down to prevent

scratches)

Fit the base cover and

thread the plug and

cord through the hole

in the middle.

Fit the base inside the

base cover (2) and

align the holes ready

for the screws and

washers.

Patio_Heaters_Assy.indd 7 03/05/2019 11:35

8

SH16320N - BAR TABLE PATIO HEATER

Fit the screws and

washers. Leave them

slightly loose for the

moment. This allows

a little movement in

the base for the next

part...

Get someone to hold

the bar base (5) in

position.

Thread the long

screws though the

holes in to the steel

tubes (8) and into the

threaded holes on the

bar base.

Don’t fully tighten

them until all 3 are

fitted

Patio_Heaters_Assy.indd 8 03/05/2019 11:35

9

SH16320N - BAR TABLE PATIO HEATER

Once all 3 of the long

screws are fitted,

tighten them all (using

the larger allen key)

Finally tighten the

base screws as well

(small allen key)

Fit the cable to the

cable tie and fit the

castors

Patio_Heaters_Assy.indd 9 03/05/2019 11:35

10

SH16320N - BAR TABLE PATIO HEATER

Turn the unit the right

way up again & offer

up the table top.

The holes must line

up as shown. The

bump (2) must align

with the hole (1)

This MUST be a 2

person task or you

risk breaking the

table top.

1

2

Fit the screws to se-

cure the table top to

the main unit.

Refer to the manual that came with the product for operation guide

Patio_Heaters_Assy.indd 10 03/05/2019 11:35

11

SH16330N - PORTABLE PATIO HEATER

1. Main body

2. Base cover

3. Base

4. Cord grip & screws

5. Allen key

6. Deco board

7. Base screws & washers

You will also need a cross head screw driver. Assembly is much

easier with two people and reduces the risk of damaging the

product.

1

2

3

45

6

7

Patio_Heaters_Assy.indd 11 03/05/2019 11:35

12

Fit the deco boards

(6) as shown

SH16330N - PORTABLE PATIO HEATER

Put the base (3)

inside the base

cover (2) and thread

the plugs and cord

through the hole in

the middle.

Make sure the 2

mounting holes are

aligned.

Patio_Heaters_Assy.indd 12 03/05/2019 11:35

13

Fit the base assem-

bly to the main body

(1) and tighten the

screws and washers

(7) as shown.

SH16330N - PORTABLE PATIO HEATER

Fit the cord grip (4)

ensuring the lip faces

upward.

Refer to the manual that came with the product for operation guide

Patio_Heaters_Assy.indd 13 03/05/2019 11:35

www.swan-brand.co.uk

PO Box 3117, Stoke-on-Trent ST4 9GD

Est.1931

We love

what we do

s

2 year

GUARANTEE

we’re proud

of our quality

Scan this QR code

to hear about

our story

Find us on Facebook

*

* on selected products

Patio_Heaters_Assy.indd 14 03/05/2019 11:35

Swan SH16310N Installation guide

Swan SH16310N Installation guide

Other documents