Sunsky EF168 User guide

Please read this entire guide before operation

Table of Contents:

Product Description............................................................1

Main Features....................................................................1

Package Contents..............................................................2

Installation of fence system................................................2

Verify the function of fence system.......................................3

Put collar receiver on your dog.............................................4

How the correction works....................................................5

System Maintenance Tips....................................................6

Troubleshooting Guidelines.................................................6

WARNING

Please charge the collar receiver before put it training! If the

collar receiver don’t work for a long time, you should charge it

fully, and charge it every month then keeping it idle.

2.Main feature

This product has three levels of function adjustable: the ﬁrst

level is only vibration function, the second level is weak static

shock function, the third level is strong static shock function.

There is a warning beeper prompt for each level.

1.Product Description

This electronic pet fence

system EF168 is reliable,

cost-eﬃcient pet containment

systems. The harmless radio

signal was issued by

transmitter and go through

the wire to be boundary of the

“yard”, when your dog

approaches the boundary beyond setting range, the receiver

collar in dog neck will start up with a warning beep at ﬁrst. If your

dog keep running to the boundary, the receiver will issue static

shock with gradually stronger intensity until your dog returns

back to the “safe area”- within the boundary you set up.

1.The function vibration or shock

When the dog closer the boundary the vibration or shock

will be stronger.

2.Beeper

A warning tone will be issued twice and then shock or

vibration if your dog continues to move closer to the boundary;

3.Variable Field Width Control:

Allows you to precisely control the width of the signal ﬁeld; (

the cable is about 200M)

4.Audible and Visual Wire Break Indicators:

Once the boundary wire was broken, the transmitter

loud sonic alarm will issue with a ﬂashing light;

5. Speed Detect Anti-Run through:

The faster your dog is moving, and the higher level of shock

or vibration intensity is issued.

6. Multiple Collar Operation:

Add as many collars as you like to contain as many animals

you have. There is no limit to the number of collars it can control.

7.Up to 5000 square meters range (over 1.24 acre).

3.Package Contents:

4.Installation of fence system

To make sure the normal operation of the fence system, you

should design a diagram of the fence system at ﬁrst. Then mount

the transmitter nearby the AV outlet, set the boundary with wire

and ﬂags, place the receiver collar into neck of your dogs.

Step 1: Mount the transmitter

To make transmitter work properly, you should ensure, there

is a 110/220VAC outlet nearby before mounting it. Place the

transmitter at a wall or tree and ﬁxed it with screws.

Please install the system as below steps:

Step 2: Install the boundary ﬂags and Connect the wire

Connect one terminal of the wire to transmitter ﬁrstly, mount

the boundary ﬂags one by one according to the boundary layout,

and make sure the wire go through the hole of ﬂags meanwhile.

Until all the ﬂags has been mounted properly along the boundary

and come back to the transmitter. Please keep the excess wire

around the bobbin and connect the terminal of wire to transmitter.

Step 3: Set parameters for transmitter

Pushing ON/OFF button to turn on/oﬀ the transmitter. The

signal ﬁeld is the distance from the wire to the place where the

collar receiver ﬁrst activates. the value of power level is bigger

and the control range is bigger. Press ON/OFF button to turn on

the transmitter, press and can adjust the control range.

Press can decrease the control range, press can increase

the control range.

Notice:

the packed. wire length of is 200 meters. you can add

more. (must use the wire that we provide)

Press the button on the transmitter and to change the

control range. According to the comparison table above, such as:

level 10. and then take the collar receiver to right location as the

right control range. Press ON/OFF button of collar receiver to

power it on and move the collar to the boundary wire. If the

warning tone of “bi-bi” and vibration are issued or bi-bi” and

shock are issued, and then place the LED test light on the collar

contact probes, the LED should light on in a few seconds (It’s

means the shock function is good). If you move the receiver collar

away from the boundary, the receiver will stop “bi-bi” and

vibration or shock.

This product has three levels of function adjustable: the ﬁrst

level is only vibration function, the second level is weak static

shock function, the third level is strong static shock function.

(There is a warning beeper prompt for each level.)

5.Verify the function of fence system

Set the transmitter signal power level:

DOWN

Receiver button and function:

1.Long press for ON/OFF

2. Setting function of receiver collar: the ﬁrst level is only

vibration function, the second level is weak static shock function,

the third level is strong static shock function. (There is a warning

beeper prompt for each level.) 1). It’s with function vibration +

beeper when the collar ON and the light on receiver collar

ﬂashing continuously one time; 2). It’s with function weak shock

and beeper when press twice ON button and the light on receiver

collar ﬂashing continuously two times; 3). It’s with function strong

shock and beeper when press three times ON button and the light

on receiver collar ﬂashing continuously three times; 4). if you

continue press ON button, the collar will cycle function.

3. If receiver collar is ﬂashing light red(.0.5S ﬂashing one

time), it’s with low battery, and now you need charge for it.

Place the collar around the dog’s neck with the receiver box

under the chin. The collar must be on relatively tight to keep the

probes making shin contact without restricting breathing. You

should be able to slide only one ﬁnger under the strap at the back

of dog’s neck. Please check the skin of the dog’s neck every day,

if the dog’s neck has any adverse reactions, you must stop use

this collar on dogs’ neck.

If the erythema is caused by too long wearing time or too

tight collar, it needs to use it after recovery.

Notice: always make sure the collar is functioning properly

before putting it on the dog.

6.Put the receiver collar on your dogs

Notice: Don’t place the receiver collar on your dog until the

fencing system has been tested and the signal ﬁeld adjusted. You

must manually test the containment system to verify that the

signal is properly transmitted trough the wire. Use the supplied

test light.

In fact, very little maintenance is required for this receiver

collar, since the receiver collar is rechargeable and waterproof,

but the transmitter is not waterproof and must be protected from

the weather. A close lighting strike may damage the unit. Unplug

the transmitter and disconnect the wires during storms.

Test the system once a week to make sure the receiver collar

is working properly. Also testing the system will verify the ﬁeld

width setting is correct. To test, attache the LED test light to the

receiver collar probes. Holding the receiver by the case( NOT by

the probes), walk into the signal ﬁeld and pay attentions to the

warning tone and LED light. The dogs closer boundary and shock

or vibration will be stronger.

8.System maintenance tips

1. Pre-correction Warning Tone:

When the dog reaches the edge of the signal ﬁeld in the

yard, it will hear a warning tone, if dogs don’t return to safe area,

the receiver collar will shock or vibration continuous until dogs

return to safe area. If dogs return to boundary again, the receiver

collar will work shock or vibration again.

2.Run-Through Prevention:

The receiver collar automatically increase the correction as

the dog enters the signal ﬁeld, tone beeper, vibration and shock

will be stronger when dogs closer boundary. Strong shock or

vibration will not allow dogs go beyond the setting range.

7.How the correction works

4. It ﬂashing light double red when charging, it light on green

when full charge, turn oﬀ the charge it return to shutdown status.

5.Receiver collar will automatic go to standby when collar

stationary 60S (power save function), and then shake the collar

will be go to work.

6.The receiver collar works: 20S continuous electric shock +

5S stop work, and then stop shock after 5 cycles, ﬂashing red

light until dogs return to safety area.

10.Important Tips

1.This model wire fence electronic is only for pet dogs;

2.When receiver collar is with low battery, it will intermittent

work, and you need stop work please.

A.Dog is not responding to correction, pay attention below

points:

1.Check the collar strap and make sure it’s proper tightness.

2.Trim the dog’s hair or use rubber probes to make better

skin contact.

3、If receiver collar is low battery, charge it.

B.System Test Procedure:

Whenever you experience a malfunction, you will need to do

a Test Loop to determine which component-collar, wall

transmitter, or yard wire-is not working. To perform the Test Loop

procedure:

1.Make a test loop using a piece of wire at least 4meters in

length.

2.Remove the existing wire from your wall transmitter.

3.Insert the two ends of the test loop wire into the wall

transmitter.

4.Set the field width level to a low setting.

5.Place the test light on the receiver collar, with the collar in

hand, move outside the field and approach the test loop. Make a

mental note of the distance between the collar and the wire when

the collar activates,

6.Set the transmitter signal level to a medium value, such as

level 4, back away from the wire and approach it again, determine

the distance should be geater on the medium range setting.

7.If more than one collar receiver is used with the system,

repeat the above test on each collar.

9.Troubleshooting Guidelines

3.Don’t wear the receiver collar on dog’s neck more than 10

hours each time.

4.Keep the receiver collar away from your child to avoid

accidental injury.

5.Please read the manual carefully before using.

Sunsky EF168 User guide

Other documents