ModelHSORH60 & HSORH90
Thank you for choosing our Range Hood
It is essential to read this manual carefully before it is installed
and used for the first time.
Do not flame under the range hood.
Before connecting this appliance,check if the power supply cord is not damaged.If the
supply cord is damaged,it must be replaced by the manufacturer,it’s service agent or
similarly qualified persons in order to avoid a hazard .
There is fire risk if cleaning is not carried out in accordance with the instructions.
have to be fulfilled.
Correct Incorrect
HSORH60
: 600/
HSORH90:900mm
PRODUCT DIMENSION
HSORH60:
530/
HSORH90
:830mm
Model :HSORH60 & HSORH90
The cooker hood can be installed as extractor or recirculation hood.
1.The cooker hood should be placed at a distance of 65-75 cm
from the cooking surface for the best effect. See Pic.1.
2. Drill 4 holes of Ø 5mm and one hole of Ø170mm at the
bottom of the hanging cupboard according to Pic.2.& Pic.3.
3.Open filters,keep the hood in line,insert screws and swelling
rubber plug,tighten the screws.Fix filters.
4.After the hood has been hung, install the optional flexible
outlet duct ( Ø150 mm ) to the vent on the top of the
cooker hood(Pic. 4).If required. Insert the second part of the
flexible duct in the opening prepared in the wall.
5. Plug the power cord into the wall outlet.
Pic 3 Installation diagram
Pic 4
INSTALLATION
Pic 2 Drill size diagram
HSORH60 / HSORH90 respectively.
* 230mm / 380mm
*460mm/760mm
170 mm 202 mm
45 mm
87 mm 150
45 mm
Before first use
Before first use you should wipe the outside and inside of the appliance with a damp
cloth for hygiene reasons.
Ventilation mode
The extracted air is discharged through the flexible outlet duct out of the room. If the
appliance is equipped with a charcoal filter, remove it (see chapter Maintenance).
Recirculation mode
If there is no possibility of discharging the extracted air out of the room, you can use
the recirculation mode. In this case, the extracted air is filtered through the metal filters
and the charcoal filter. An active carbon in this filter absorbs the smell. Air, free from
odours, flows back into the room through openings situated in the front cover of the
appliance's body. When the recirculation mode is used, it is necessary to purchase
and install the appropriate charcoal filters (see chapter Maintenance).
Operation step
1.Slide the front of the appliance to extend the air suction capacity.
2. Use the switches according to the switch instruction.
OPERATION
1. Motor switch
I is low speed,II is high speed,O is off .
2. Lamp switch
I is light on,O is light off.
Disconnect the power cord from the wall outlet before cleaning and maintenance.
To clean the appliance outside, use a damp cloth, a soft brush or a fine sponge, and
then wipe it dry.Do not use coarse abrasive cleaning agents or sharp metal scrapers
for cleaning of the appliance as this could result in surface scoring.
Never leave aggressive or acidic substances (lemon juice, vinegar) on enamelled or
stainless parts of the appliance.
Cleaning and replacement of filters
Metal grease filters
When the appliance is in common use, the metal grease filters should be checked
or cleaned every month. In case of more frequent frying or deep frying, shorten this
interval.
Do not use the appliance without the metal grease filters properly installed!
1.Remove the metal filters as shown in Fig. 1.
2.Let the metal filters soak in warm water with addition of a detergent or put them
into a washer with a cleaning agent and set temperature below 60 °C. In case of
soaking in warm water, clean the metal filters with a fine brush, rinse them with
clean water and let them dry.
3.Attach the dried filters back.
Fig.1
Charcoal filter (to be purchased)
This filter is only used for the recirculation mode.
The filter contains an active carbon absorbing the smell being discharged. The active
carbon will be saturated after some time, hence the absorption capacity will be
shortened. This filter cannot be washed or cleaned in any other way.
When the appliance is in common use, the charcoal filter should be replaced every
2-3 months. In case of more frequent frying or deep frying, shorten this interval.
1.Remove the metal filters as shown in Fig. 1.
2.The charcoal filters are situated on both sides of the motor. Turn the filters, until
they are secured (see Fig. 2).
3.To replace the charcoal filter, proceed in reverse order.
Closed
ClosedOpened
Opened
Fig. 2
Oil drops from the
metal grease filer Heavily fouled filer
Immediately clean or
replace the metal grease
filer
TROUBLESHOOTING
/