Delta Electronics Function Card DVP-EH User manual

Type
User manual

Delta Electronics Function Card DVP-EH

The Delta Electronics Function Card DVP-EH is a versatile and powerful device that can be used to enhance the capabilities of your PLC system. With its wide range of features and options, the DVP-EH can be used in a variety of applications, from simple automation tasks to complex control systems.

Some of the key features of the DVP-EH include:

  • High-speed I/O: The DVP-EH offers high-speed I/O capabilities, with a maximum input frequency of 200KHz and a maximum output frequency of 100KHz. This makes it ideal for applications where fast and accurate control is required.

Delta Electronics Function Card DVP-EH

The Delta Electronics Function Card DVP-EH is a versatile and powerful device that can be used to enhance the capabilities of your PLC system. With its wide range of features and options, the DVP-EH can be used in a variety of applications, from simple automation tasks to complex control systems.

Some of the key features of the DVP-EH include:

  • High-speed I/O: The DVP-EH offers high-speed I/O capabilities, with a maximum input frequency of 200KHz and a maximum output frequency of 100KHz. This makes it ideal for applications where fast and accurate control is required.
Warning
This Instruction Sheet only provides descriptions for electrical specifications, general specifications, installation &
wiring. Other detail infromation about programming and intructions is compatible with SV series; please see PLC
Application Manual. For more information about the optional peripherals, please see individual product instuction
shee or “DVP-PLC Application Manual: Special module”.
This is an OPEN TYPE PLC. The PLC should be kept in an enclosure away from airborne dust, humidity, electric
shock risk and vibration. Also, it is equipped with protective methods such as some special tools or keys to open the
enclosure, in order to prevent hazard to users or damage the PLC.
Do NOT connect the AC main circuit power supply to any of the input/output terminals, or it may damage the PLC.
Check all the wiring prior to power up. To prevent any electromagnetic noise, make sure the PLC is properly
grounded . Do NOT touch terminals when power on.
Introduction
Product Profile & Outline
Communication port cover
I/O terminal cover
Function card/memory card cover
I/O terminals
I/O terminal No.
Extension module connection port cover
Input indicator
Output indicator
DIN rail clip
1
2
3
5
9 4
9
6
10
5
4
7
8
DIN rail (35mm)
Mounting screws
Direct mounting hole
Battery socket
Function card mounting hole
Memory card port
POWER/RUN/BAT.LOW/ERROR indicator
3
1
2
6
7
1
2
5
4
8
Extension module connection port
Dimension
Model W (mm) W1 (mm)
DVP16EH00R/T 113 103
DVP20EH00R/T 113 103
DVP32EH00R/T 143.5 133.5
DVP32EH00M 158.8 153.8
DVP40EH00R/T 158.8 153.8
DVP48EH00R/T 174 164
DVP64EH00R/T 212 202
4
.
6
X
2
W
W1
80.0
9
0
.
0
82.2
DVP80EH00R/T 276 266
ENGLISH
Specifications
Model
Item
16EH00
20EH00
32EH00
32EH00M
40EH00
48EH00
64EH00
80EH00
Power supply
voltage
100 ~ 240V AC (-15% ~ 10%), 50/60Hz ± 5%
Fuse capacity 2A/250V AC
Power consumption
50VA 50VA 60VA 60VA 60VA 60VA 80VA 80VA
DC24V current
supply
500mA 500mA 500mA 500mA 500mA 500mA 500mA 500mA
Power protection DC24V; output short-circuit
Withstand voltage 1,500V AC (Primary-secondary), 1,500V AC (Primary-PE), 500V AC (Secondary-PE)
Insulation resistance > 5M (all I/O point-to-ground: 500V DC)
Noise immunity
ESD: 8KV Air Discharge, EFT: Power Line: 2KV, Digital I/O: 1KV, Analog & Communication I/O:
250V
Damped-Oscillatory Wave: Power Line: 1KV, Digital I/O: 1KV, RS: 26MHz~1GHz, 10V/m
Earth
The diameter of grounding wire shall not be less than that of L, N terminal of the power. (When
many PLCs are in use at the same time, please make sure every PLC is properly grounded.)
Operation/storage
Operation: 0°C ~ 55°C (temperature), 50 ~ 95% (humidity), pollution degree: 2
Storage: -40°C ~70°C (temperature), 5 ~ 95% (humidity)
Vibration/shock
immunity
International standard: IEC61131-2, IEC 68-2-6 (TEST Fc)/IEC61131-2 & IEC 68-2-27 (TEST Ea)
Weight (g) 500/480 520/500 652/612 644 710/675 748/688 836/756 948/848
Input Point Specification
24V DC single common port input Spec.
Items
Differential input
5VDC two inputs
Low speed High speed 200KHz
Note
Input wiring type
Independent
wiring
Change wiring from S/S to SINK or SOURCE
Input indicator LED display, light on = ON, light off = OFF
Input voltage 5V DC 24V DC
Off On
> 5mA
X0~X7,X12,X13,X16,X17,X20~X47: > 18.5V
X10,X11,X14,X15: > 16.5V
Active
Level
On Off
< 2mA X0~X47: < 8V DC
1. Differential input is only for
X0, X1, X4 and X5 on
DVP32EH00M.
2. Only X0, X1, X4 and X5 on
DVP32EH00M are
equipped
with high-speed input.
Response time/
noise immunity
0.5us 10ms 0.5us
Input point X0 ~ X7, X10 ~
X17 can conduct 10 ~ 60ms
digital filter adjustment
Output Point Specification
Single common port transistor output
Spec.
Items
Two differential
outputs
Low speed High speed
Single common port relay output
Max. frequency 200KHz 10KHz 200KHz Load ON/OFF control
Output indicator LED display, light on = ON, light off = OFF
Min. load - 2mA/DC power supply
Working voltage 5V DC 5 ~ 30V DC < 250V AC, 30V DC
Insulation Line Driver Photocoupler Magnetic
Current
specification
< 25mA 0.3A/1 point @ 40°C
30mA
2A/1 point (5A/COM)
75VA (conductive), 90W (resistive)
Off On, 20us
Max. output
delay time
0.2us
On Off, 30us
0.2us 10ms
Over-current
protection
N/A
Note: Differential output points are only Y0 ~ Y3 on DVP32EH00M; other output points are for relay output.
Installation & Wiring
3.1 PLC Mounting Arrangements and Wiring Notes
How to install DIN rail:
DVP-PLC can be secured to a cabinet by using the DIN rail of 35mm in height and
7.5mm in depth. When mounting PLC to DIN rail, be sure to use the end bracket to stop
any side-to-side movement of PLC and reduce the chance of wires being loosen. A small
retaining clip is at the bottom of PLC. To secure PLC to DIN rail, place the clip onto the
rail and gently push it up. To remove it, pull the retaining clip down and gently remove
PLC from DIN rail, as shown in the figure.
How to screw: Please use M4 screw according to the dimension of the product.
DV P MPU
> 50mm> 50mm
> 50mm
> 50mm
Please install PLC in an enclosure with sufficient space around it to allow heat
dissipation as shown in the figure.
Wiring:
To suit M3.5 screw terminals
Below 6.2
Below 6.2
1. Use O-type or Y-type terminal. See the figure in the left hand side for its
specification. PLC terminal screws should be tightened to 5 ~ 8 kg-cm (4.3 ~
6.9 in-Ibs) and please use only 60/75ºC copper conductor.
2. DO NOT wire empty terminal . DO NOT place the input signal cable and
output power cable in the same wiring circuit.
3. DO NOT drop tiny metallic conductor into the PLC while screwing and wiring.
Tear off the sticker on the heat dissipation hole for preventing alien
substances from dropping in, to ensure normal heat dissipation of the PLC.
3.2 Wiring Notes
Power Input Wiring
The power input of DVP-EH series is AC. When operating the PLC, please make sure that:
1. The input voltage should be current and its range should be 100 ~ 240V AC. The power should be
connected to L and N terminals. Wiring AC110V or AC220V to +24V terminal or input terminal will result in
serious damage on the PLC.
2. The AC power input for PLC MPU and I/O extension modules should be ON or OFF at the same time.
3. Use wires of 1.6mm (or longer) for the grounding of PLC MPU. The power shutdown of less than 10ms will
not affect the operation of the PLC. However, power shutdown time that is too long or the drop of power
voltage will stop the operation of the PLC and all outputs will go OFF. When the power supply turns normal
again, the PLC will automatically return to its operation. Please be aware of the latched auxiliary relays and
registers inside the PLC when programming.
AC Power Input
L
N
2.0 A
DC/DC
+5V
+24V
24G
S/S X0 X1 X2
100~240 VAC
0.5A is the maximum power supply for +24V power supply output terminal. DO NOT connect other
external power supplies to this terminal. Every input terminal requires 6 ~ 7mA to be driven; e.g. the
16-point input will require approximately 100mA. Therefore, +24V cannot give output to extermal load
that is more than 400mA.
Safety Wiring
Since a PLC controls many devices, actions of any device may affect actions of other devices, and the
breakdown of any one device may cause the breakdown of the whole auto-control system and danger.
Therefore, we suggest you wire a protection circuit at the power input terminal, as shown in the figure below.
AC power supply load
Power circuit protection fuse (3A
Power indicator
Emergency stop
This button can cut off the system power supply when accidental
emergency takes place.
System circuit isolation device
The device is made of electromagnetic contactor and relay as the
switch to prevent the instability of system when the power is
intermittently supplied.
DVP-PLC (main processing unit)
Earth
MC
MC
NL
1
1
2
3
4
5
6
8
Gua rd
Limi t
MC
Power supply
AC: 100 ~ 240V AC, 50/60Hz; DC: 240V DC
Input Point Wiring
There are two types of DC inputs, SINK and SOURCE.
Input point loop equivalent circuit Wiring loop
DC Signal IN
S/S
X0
Sinking
SINK mode
(common port for current
input S/S)
24VDC
24G
X0
S/S
+24V
SINK
+5V
24G S/S X0 X1 X2+24V
Sink Type
Input point loop equivalent circuit Wiring loop
DC Signal IN
S/S
X0
Sourcing
SOURCE mode
(common port for current
output S/S)
24VDC
24G
X0
S/S
+24V
SOURCE
+5V
24G S/S X0 X1 X2+24V
Source Type
Wiring of Differential Input
X0 ~ X1 and X4 ~ X5 of DVP32EH00M are all high-speed input circuit and others are DC24V input. The
working frequency of high-speed input circuit can reach up to 200KHz and is mainly for connecting to
differential (double-wire) LINE DRIVER output circuit. In an low-noise and low-frequency (less than 50KHz)
environment, you may also use DC5V SINK/SOURCE input of a single port or series-connect a 2K/0.5W
resistance for transferring into DC24V SINK/SOURCE input of a single port.
Wiring in a high-speed, high-noise environment
A +
A -
B +
B -
A
B
X0+
X0-
X1+
X1-
DV P3 2EH 00M hig h-s pee d ou tpu t
En co der o utp ut
Di ffe ren tial out put
Twisted pai r
cable
Wiring of DVP32EH00M DC5V SINK Wiring of DVP32EH00M DC5V SOURCE
(5V SINK)
NPN
SENSOR
+
5V
X0+
X0 -
(5V SOURCE)
+
5V
PNP
SENS OR
X0+
X0 -
Wiring of from DC5V to DC24V SINK Wiring of from DC5V to DC24V SOURCE
2K / 0.5W
(24V SINK)
24V
+
NPN
SENSOR
X0+
X0 -
2K / 0. 5W
(24V SO URCE )
24V
+
PNP
SENS OR
X1+
X1 -
Output Point Wiring
Relay (R) contact circuit wiring
Y0
RY
LED
C0
LOAD
POWER
DVP-**-**-**-R
RELAY OUTPUT
MC2MC1
1
2
3
6
7
4
9
10
2
3
8
C0 Y1Y0 Y6C1 Y4 Y5 Y7
5
Flywheel diode: To extend the life span of contact
Emergency stop: Uses external switch
Fuse: Uses 5 ~ 10A fuse at the common port of output contacts to protect the output circuit.
Varistor: To reduce the interference on AC load
Empty terminal: not in use
DC power supply
Neon indicator
AC power supply
Incandescent light (resistive load)
Manually exclusive output: Uses external circuit and forms an interlock , together with the
PLC internal program, to
ensure safety protection in case of any unexpected errors.
Transistor (T) contact circuit wiring
Y0
LED
C0
TRAN SISTO R OUT PUT
LOAD
DVP- **-**- **-T
< 0.5 A
T
r
i
g
g
e
r
c
i
r
c
u
i
t
6
MC1
MC2
2
3
1
C0 Y0 Y1 C1 Y 4 Y 5 Y 6 Y 7
5
7
4
7
3
Tran sist or o utp ut E xam ple (sin k ou tpu t wi rin g)
DC power supply
Emergency stop
Circuit protection fuse
Empty terminal
Due to all outputs are Open Collect ors, if Y0 is set as pulse output, the output current has to be bigger than 0.1A to
ensure normal operation of the transistor module.
Due to all outputs are Open Collect ors, if Y1 is set as pulse output, the output current has to be bigger than 0.1A to
ensure normal operation of the transistor module.
Manually exclusive output: Uses external circuit and forms an interlock, together with the PLC internal program, to
ensure safety protection in case of any unexpected errors.
Wiring of Differential Output
A +
A -
B +
B -
Y0
Y1
PLC
Circu it for Photoc ouple
Circu it for Lin e Rec eiver
Y0+
Y0-
Y1+
Y1-
SG0
Twisted
pair cable
Driv er
SV
DVP-PLC DVP-PLC
(OPEN T YPE) /
DIN
1
2
3
5
9 4
9
6
10
5
4
7
8
DIN (35mm)
3
1
2
6
7
1
2
5
4
8
4
.
6
X
2
W
W1
80.0
9
0
.
0
82 .2
W (mm) W1 (mm)
DVP16EH00R/T 113 103
DVP20EH00R/T 113 103
DVP32EH00R/T 143.5 133.5
DVP40EH00R/T 158.8 153.8
DVP48EH00R/T 158.8 153.8
DVP64EH00R/T 212 202
DVP80EH00R/T 276 266
16EH00
20EH00
32EH00
32EH00M
40EH00
48EH00
64EH00
80EH00
100 ~ 240V AC (-15% ~ 10%), 50/60Hz ± 5%
2 A / 250VAC
50VA 50VA 60VA 60VA 60VA 60VA 80VA 80VA
DC24V
500mA 500mA 5 00mA 500mA 500mA 500mA 500mA 5 00mA
DC24V
1.500V AC (Primary-secondary) 1,500V AC (Primary-PE) 500V AC (Secondary-PE)
5 M 500V DC
ESD: 8KV Air Discharge EFT: Power Line: 2KV, Digital I/O: 1KV, Analog & Communication I/O: 250V
Damped-Oscillatory Wave: Power Line: 1KV, Digital I/O: 1KV, RS: 26MHz ~ 1GHz, 10V/m
L, N PLC
0°C ~ 55°C 50 ~ 95% 2
-40°C ~ 70°C 5 ~ 95%
IEC61131-2, IEC 68-2-6 (TEST Fc)/IEC61131-2 & IEC 68-2-27 (TEST Ea)
g 500/480 520/500 652/612 644 710/675 748/688 836/756 948/848
24V DC
5V DC
200KHz
S/S SINK SOURCE
LED ’ON’ ’OFF’
5V DC ± 10% 24V DC ± 10%
Off On > 5mA
X0~X7,X12,X13,X16,X17,X20~X47 > 18.5V
X10,X11,X14,X15 > 16.5V
On Off < 2mA
X0~X47 < 8V DC
1.
DVP32EH00M
X0, X1, X4,
X5
2. DVP32EH00M
X0, X1, X4, X5
0.5us 10 ms 0.5us
X0 ~ X7 X10 ~
X17 10 ~ 60 ms
200KHz 10KHz 200KHz
ON/OFF ,
LED ’ON’ ’OFF’
-
2mA/DC
5VDC ± 10% 5 ~ 30V DC < 250V AC, 30V DC
25mA 0.3A/1 @ 40°C
30mA
2A/1 (5A/COM)
75VA 90W
OffOn
20us
OnOff
0.2us
30us
0.2us 10ms
DVP32EH00M Y0 ~ Y3
4.1
DIN
35mm DIN PLC PLC
PLC PLC
PLC
DVP MPU
50mm
50mm
50mm
50mm
PLC
PLC
M4
6.2
6.2
M3.5
1. O Y PLC
5 ~ 8 kg-cm (4.3 ~ 6.9 in-lbs) 60/75°C
2.
3. PLC
PLC
4.2
DVP-EH PLC
1. 100 ~ 240V AC L N AC110V AC220V
+24V PLC
2. I/O On Off
3. 1.6mm
4. 10ms PLC PLC
Off PLC PLC
L
N
2.0 A
DC/DC
+5V
+24V
24G S/S
X0 X1 X2
100~240VAC
+24V 0.5A 6 ~
7mA 16 100mA +24V 400mA
PLC
(3A)
DVP PLC
MC
MC
NL
1
1
2
3
4
5
6
8
Guar d
Li mi t
MC
AC 100 ~ 240VAC 50/60Hz
DC 24V DC
DC DC SINK SOURCE
DC Signal IN
S/S
X0
Sinking
SINK
( S/S)
24VDC
24G
X0
S/S
+24V
SINK
+5V
24G
S/S
X0 X1 X2
+24V
Sink Type
DC Signal IN
S/S
X0
Sourcing
SOURCE
( S/S)
24VDC
24G
X0
S/S
+24V
SOURCE
+5V
24G S/S X0 X1 X2
+24V
Source Type
DVP32EH00M X0 ~ X1 X4 ~ X5 DC5V DC24V
200KHz LINE DRIVER
50KHz DC5V SINK/SOURCE 2K/0.5W
DC24V SINK/SOURCE
A +
A -
B +
B -
A
B
X0 +
X0 -
X1 +
X1 -
DV P32E H00 M
DVP32EH00M DC5V SINK DVP32EH00M DC5V SOURCE
(5V SINK)
NPN
SENSOR
+
5V
X0+
X0 -
(5V SOUR CE)
+
5V
PNP
SENS OR
X0+
X0 -
DC5V DC24V SINK DC5V DC24V SOURCE
2K / 0.5W
(24V SINK)
24V
+
NPN
SENSOR
X0+
X0 -
2K / 0 .5W
(24 V SOUR CE)
24V
+
PNP
SENS OR
X1+
X1 -
(R)
Y0
RY
LED
C0
LOAD
POWER
DVP-**-**-**-R
RELAY OUTPUT
2
3
1
5
C0 Y 0 Y1 C1 Y 3 Y4
C2
Y6 Y 7
4
MC1
MC2
7
10
3
2
8
9
6
5 ~ 10A
PLC
(T)
DVP-**-**-**-T
TRANSISTOR O UTPUT
LED
Y0
C0
LOAD
0.5A
6
MC1
MC2
2
3
1
C0 Y0 Y1 C 1 Y 4 Y 5 Y 6 Y7
5
7 47
3
+
Y0 0.1A
Y1 0.1A
PLC
A +
A -
B +
B -
Y0
Y1
PLC
Pho toc ou ple
Lin e R ecei ver
Y0+
Y0-
Y1+
Y1-
SG0
SV
DVP-PLC DVP-PLC
(OPEN T YPE)
DIN
1
2
3
5
9 4
9
6
10
5
4
7
8
DIN (35mm)
3
1
2
6
7
1
2
5
4
8
4
.
6
X
2
W
W1
80.0
9
0
.
0
82 .2
W (mm) W1 (mm)
DVP16EH00R/T 113 103
DVP20EH00R/T 113 103
DVP32EH00R/T 143.5 133.5
DVP40EH00R/T 158.8 153.8
DVP48EH00R/T 158.8 153.8
DVP64EH00R/T 212 202
DVP80EH00R/T 276 266
16EH00
20EH00
32EH00
32EH00M
40EH00
48EH00
64EH00
80EH00
100 ~ 240V AC (-15% ~ 10%), 50/60Hz ± 5%
2 A / 250VAC
50VA 50VA 60VA 60VA 60VA 60VA 80VA 80VA
DC24V
500mA 500mA 5 00mA 500mA 500mA 500mA 500mA 5 00mA
DC24V
1.500V AC (Primary-secondary) 1,500V AC (Primary-PE) 500V AC (Seco ndary-PE)
5 M 500V DC
ESD: 8KV Air Discharge EFT: Power Line: 2KV, Digital I/O: 1KV, Analog & Communication I/O: 250V
Damped-Oscillatory Wave: Power Line: 1KV, Digital I/O: 1KV, RS: 26MHz ~ 1GHz, 10V/m
L, N PLC
0°C ~ 55°C 50 ~ 95% 2
-40°C ~ 70°C 5 ~ 95%
IEC61131-2, IEC 68-2-6 (TEST Fc)/IEC61131-2 & IEC 68-2-27 (TEST Ea)
g
500/480 520/500 652/612 644 710/675 748/688 836/756 948/848
24V DC
5V DC
200KHz
S/S SINK SOURCE
LED ’ON’ ’OFF’
5V DC 24V DC
Off On
> 5mA
X0~X7,X12,X13,X16,X17,X20~X47 > 18.5V
X10,X11,X14,X15 > 16.5V
On Off
< 2mA
X0~X47 < 8V DC
1.
DVP32EH00M
X0, X1, X4,
X5
2. DVP32EH00M
X0, X1, X4, X5
0.5us 10 ms 0.5us
X0 ~ X7 X10 ~
X17 10 ~ 60 ms
200KHz 10KHz 200KHz
ON/OFF ,
LED ’ON’ ’OFF’
-
2mA/DC
5VDC ± 10% 5 ~ 30V DC < 250V AC, 30V DC
25mA 0.3A/1 @ 40°C 30mA
2A/1 (5A/COM)
75VA 90W
Off On
20us
On Off
0.2us
30us
0.2us 10ms
DVP32EH00M Y0 ~ Y3
3.1
DIN
35mm DIN PLC PLC
PLC PLC
PLC
DVP MPU
50mm
50mm
50mm
50mm
PLC
PLC
M4
6.2
6.2
M3.5
1. O Y PLC
5 ~ 8 kg-cm (4.3 ~ 6.9 in-lbs) 60/75°C
2.
3. PLC
PLC
3.2
DVP-EH PLC
1. 100 ~ 240V AC L N AC110V AC220V
+24V PLC
2. I/O On Off
3. 1.6mm
4. 10ms PLC PLC
Off PLC PLC
L
N
2.0 A
DC/DC
+5V
+24V
24G S/S
X0 X1 X2
100~240VAC
+24V 0.5A 6 ~ 7mA
16 100mA +24V 400mA
PLC
(3A)
DVP PLC
MC
MC
NL
1
1
2
3
4
5
6
8
Guar d
Li mi t
MC
AC 100 ~ 240VAC 50/60Hz
DC 24V DC
DC DC SINK SOURCE
DC Signal IN
S/S
X0
Sinking
SINK
( S/S)
24VDC
24G
X0
S/S
+24V
SINK
+5V
24G S/S X0 X1 X2
+24V
Sink Type
DC Signal IN
S/S
X0
Sourcing
SOURCE
( S/S)
24VDC
24G
X0
S/S
+24V
SOURCE
+5V
24G S/S X0 X1 X2+24V
Source Type
DVP32EH00M X0 ~ X1 X4 ~ X5 DC5V DC24V
200KHz LINE DRIVER
50KHz DC5V SINK/SOURCE 2K/0.5W
DC24V SINK/SOURCE
A +
A -
B +
B -
A
B
X0+
X0-
X1+
X1-
DVP32 EH00M
DVP32EH00M DC5V SINK DVP32EH00M DC5V SOURCE
(5V SINK)
NPN
SENSOR
+
5V
X0+
X0 -
(5V SOUR CE)
+
5V
PNP
SENS OR
X0+
X0 -
DC5V DC24V SINK DC5V DC24V SOURCE
2K / 0.5W
(24V SINK)
24V
+
NPN
SENSOR
X0+
X0 -
2K / 0 .5W
(24 V SOUR CE)
24V
+
PNP
SENS OR
X1+
X1 -
(R)
LE D
Y0
C0
LOA D
DVP-** -**-**- R
POWE R
REL AY OUT PU T
2
3
1
5
C0 Y 0 Y1 C1 Y 3 Y4
C2
Y6
Y7
4
MC1
MC2
7
10
3
2
8
9
6
5 ~ 10A
PLC
(T)
LED
Y0
C0
LOA D
0.5 A
TRAN SISTOR OUTP UT
DV P-** -* *-** -T
6
MC1
MC2
2
3
1
C0 Y0 Y1 C 1 Y 4 Y 5 Y 6 Y7
5
7 47
3
+
Y0 0.1A
Y1 0.1A
PLC
A +
A -
B +
B -
Y0
Y1
PLC
Phot ocoupl e
Line Receive r
Y0+
Y0-
Y1+
Y1-
SG0
  • Page 1 1
  • Page 2 2

Delta Electronics Function Card DVP-EH User manual

Type
User manual

Delta Electronics Function Card DVP-EH

The Delta Electronics Function Card DVP-EH is a versatile and powerful device that can be used to enhance the capabilities of your PLC system. With its wide range of features and options, the DVP-EH can be used in a variety of applications, from simple automation tasks to complex control systems.

Some of the key features of the DVP-EH include:

  • High-speed I/O: The DVP-EH offers high-speed I/O capabilities, with a maximum input frequency of 200KHz and a maximum output frequency of 100KHz. This makes it ideal for applications where fast and accurate control is required.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI